How it Works
Kia
Loading...
1U056 ADU00

Kia 1U056 ADU00 Installation Instructions Manual

Vehicle Model Sorento (Key Start) Accessory Remote Engine Start
Model Year 2014 ~ Diffi culty ( B ) Part No. 1U056 ADU00
Instruction Symbols / Defi nitions
KIA Genuine Accessories
( A ) Customer ( B ) Dealer Technician ( C ) Master Technician
Ensure vehicle is equipped with automatic transmission, power door locks and power windows. If the vehicle is not equipped with these options, do not proceed. Ensure vehicle does NOT have SMART KEY.
Denotes warnings that may lead to serious physical injury or vehicle damage.
!
Denotes cautions to be taken to avoid physical injury or electronic component damage.
Denotes cautions to be taken to avoid vehicle and component damage.
Basic Required Hand Tools
Ratchet
#2 Phillips Screwdriver
10 mm Socket
Pliers
Tape Measure
Extension
Denotes quality processes to be checked prior to moving to the next step.
Denotes specifi c tools that are neces- sary to complete the step.
N
Denotes instructional steps
O
necessary to complete the
T
process.
E
Notes to the Installer:
Read the entire installation manual prior to beginning the installation of the accessory.
Factory wire harness colors are subject to change, please use the specifi ed pin # in the harness connector to identify the correct wire for T-Tap installation.
Ensure that the vehicle is properly protected in the area that the accessory is to be installed.
To prevent vehicle damage, never place tools on top of painted surfaces, seats, dash pad, console or fl oor carpet / mat.
Always wear appropriate safety gear to include gloves and eye protection when required.
To prevent stress on the remote start wire harness, ensure the tilt/telescopic steering column is fully extended, if equipped.
Ensure the transportation fuse is properly installed before performing the function check on page 17.
Denotes safety equipment required to be used such as a mask, goggles, rubber gloves, and hearing protection.
Mask
Goggles
Rubber Gloves Hearing Protection
Alcohol Cleaner /
Trim Tool
Wire Cutter
Clean Cloth
Torque Wrench
P/N: 4280516, Rev. A
Revision Date
4/22/2013
Technical Support
For Authorized Dealers - (800) 667-5176 Hours: 9:00 a.m. - 5:30 p.m. EST Monday - Friday
Page 1 of 25
1 2 3 4 5
Control Module P/N: U8560 00002 DNA P/N: 1U056 ADUS1
KIA Genuine Accessories
P/N: 00056 ADU50 P/N: U8560 00009
P/N: 1U056 ADUS2
Hardware Kit
6
Installation Instructions
No. Qty. Description No. Qty. Description
1 1 Control Module/DNA 6 1 Installation Instructions 2 1 Dipole Antenna 7 1 Owner’s Guide 3 2 Transmitters 8 1 Quick Reference Guide 4 1 Wire Harness 9 1 Warning Label 5 1 Hardware Kit 10 6* 15” Wire Tie (Large)
Owner’s Guide Quick Reference Guide
7
8
9
Warning Label
10
15” Wire Tie (Large)
Hardware Kit Contents
A
12*
8” Wire Tie (Small)
Hardware Kit Total
18
* Extra components intentionally placed in kit as spares. Please follow directions for proper placement of each component.
B
Female T-Tap
2*
C
3
Small Foam Tape
Revision Date
4/22/2013
D
M6 Serrated Flange
1
Hex Nut
Page 2 of 25
T-Tap Installation Procedure
Factory wire harness colors are subject to change. Please use the specifi ed pin # in the harness connector to identify the correct wire for T-Tap installation.
KIA Genuine Accessories
Spade Terminal
Pointed Up
INCORRECT INCORRECT
Spade Terminal
Pointed Down
1. Place T-Tap on vehicle wire.
N
O OO
NO GOOD
D
2. Using pliers, close and crimp T-Tap around vehicle wire.
** Extreme care must be taken to ensure that the male spade
terminal is inserted into the T-Tap properly.
CORRECT
Spade Terminal CENTERED
Inside Connector
3. Insert harness wire with male spade terminal end into the T-Tap.
Disconnecting Connectors
When disconnecting connectors, grasp the connec­tors, not the wires.
Wire Colors
When a two-color wire is listed, the fi rst color indicates the base color of the wire, the second color indicates the color of the stripe. For example: Black/White.
Striped Wire
Black (Base Color)
White (Stripe Color)
Solid Wire
Black
Locking Connectors
When locking connectors, listen for a click indicating they are securely locked.
Connector Diagrams
Connector diagrams may be shown on the har­ness side or the terminal side, extreme care must be taken to verify proper terminal location before a T-Tap connection is made.
Revision Date
4/22/2013
Terminal End View
Harness End View
Page 3 of 25
KIA Genuine Accessories
Vehicle Preparation
1. Clean hands.
2. Set the parking brake and open driver’s door window.
3. Vehicle should be at room temperature.
4. Ensure vehicle is equipped with automatic transmission, power door locks and power windows. If the vehicle
is not equipped with these options, do not proceed. Ensure vehicle DOES NOT have SMART KEY.
5. ENSURE THE TILT/TELESCOPIC STEERING WHEEL COLUMN IS FULLY EXTENDED AND LOCKED BEFORE
INSTALLING THIS ACCESSORY.
Fuse Box
Goggles
Rubber Gloves
Ratchet, 10 mm Socket, Alcohol Cleaner and Clean Cloth
1. Remove and isolate the negative battery cable from
N
the battery.
O
2. Using alcohol and a clean cloth, clean the top
T
surface of the underhood fuse box. Ensure the
E
surface is completely dry.
3. Remove the backing on the warning label and mount in place, as shown above.
WARNING! Shock Hazard. Do not touch vehicle’s negative battery terminal to vehicle’s
!
positive battery terminal. Serious physical
injury or vehicle damage may occur.
Warning Label
Negative Battery Cable
1
Pressure Clips
Fuse Panel Access Cover
Trim Tool
1. Remove the fuse panel access cover to assist in
N
the removal of the driver’s side dash end cap.
O
2. Remove the driver’s side dash end cap panel by
T
prying outward to disengage the four (4) pressure
E
clips.
0
2
Phillips Screws
Retaining Tabs
#2 Phillips Screwdriver
1. Remove the two (2) #2 phillips screws from the side
N
of the lower dash fi nish panel.
O T
E
Pressure Clips
Phillips Screws
Retaining Clip
#2 Phillips Screwdriver and Trim Tool
1. Remove the lower dash fi nish panel by removing
N
the two (2) #2 phillips screws from the bottom of
O
the panel. Using a trim tool, carefully pry outward
T
to release the two (2) retaining tabs from the side,
E
3
as shown in Step 3 and the fi ve (5) pressure clips from the front of the panel.
2. Disengage the driver’s side kick panel retaining clip from the lower dash fi nish panel.
3. Remove the OBDII connector from the panel.
4. Disconnect the remaining connectors, if equipped.
4
Revision Date
4/22/2013
Page 4 of 25
KIA Genuine Accessories
10 mm Bolts
10 mm Nut
Ratchet, Extension and 10 mm Socket
1. Remove the fi ve (5) 10 mm bolts and the one (1)
N
10 mm nut securing the steel knee bolster panel.
O
2. Remove the steel knee bolster panel from the
T
vehicle.
E
Phillips Screws
#2 Phillips Screwdriver and Trim Tool
1. Remove the three (3) #2 phillips screws securing
N
the steering column shroud (one (1) underneath
O
and two (2) behind the steering wheel). Turn the
5
T
steering wheel for access.
E
2. Release the tilt steering wheel adjuster lever.
3. Pull down to separate the lower steering column shroud (use trim tool, if necessary) and remove from the vehicle.
6
Access Cover and Phillips Screw
Trim Tool and #2 Phillips Screwdriver
1. Carefully pull the weatherstrip away from the driver’s
N
side “A” pillar.
O
2. Remove the access cover and the one (1) #2 phillips
T
screw from the “A” pillar.
E
Pressure Clips
Trim Tool
N
1. Starting at the top, use a trim tool and remove the
O
driver’s side “A” pillar trim panel by inserting the
T
tool behind the panel and prying outward to release
E
7
the two (2) pressure clips.
WARNING! Do not damage air bag components.
!
CAUTION! Do not lose the two (2) pressure clips.
8
Revision Date
4/22/2013
Page 5 of 25
Rubber Gloves
Goggles
KIA Genuine Accessories
Alcohol Cleaner, Clean Cloth and Tape Measure
1. Clean the area of the windshield where the antenna will be mounted with an alcohol cleaner and clean cloth.
N
Ensure the glass surface is completely dry.
O T
2. Remove protective backing and mount the dipole antenna to the windshield approximately 0.25” (7 mm) below the
E
mirrors lowest attachment point and/or any windshield electronic gridwork. Press fi rmly to ensure a good glass to adhesive bond.
10” (254 mm)
9"
Foam Tape
10” (254 mm)
9"
7” (178 mm)
10"
9
Trim Tool and Tape Measure
1. Wrap the antenna cable with three (3) pieces of small foam tape, at the distances shown above, to ensure that the
N
antenna cable will stay in place after routing.
O
2. Route the antenna cable vertically on the right hand side of the mirror mount up to the headliner. Tuck the cable
T
behind the headliner and down the “A” pillar, as shown above.
E
Revision Date
4/22/2013
10
Page 6 of 25
Air Bag Infl ator
KIA Genuine Accessories
Small Wire Ties
Antenna Cable
Wire Cutter
1. Use four (4) small wire ties to secure the antenna cable to the factory harness located within the “A” pillar, as
N
shown above. Trim off excess wire ties.
O T
E
WARNING! Air Bag system interference hazard. DO NOT wrap antenna cable around or secure antenna cable to any Air Bag components. Damage to the vehicle’s Air Bag system may occur which could result
!
in serious physical injury.
CAUTION! Ensure the antenna cable is routed away from the Air Bag Infl ator.
CAUTION! If the vehicle is equipped with a sunroof, be careful not to place the wire ties around the drain tube or the sunroof may not drain properly.
Antenna Cable Connector
11
16-Pin
N
1. Remove the two (2) transmitters and attach individually to each factory key.
O
2. Route the antenna cable past the left side of the dashboard and over to the dash wall area.
T
3. Plug the remote start harness 16-pin connector, 24-pin connector, 10-pin connector and the 2-pin antenna cable
E
connector into the remote start control module before mounting.
4. Ensure all connectors are properly locked into position.
CAUTION! Be careful not to bend/damage any of the terminals inside the remote start module.
Revision Date
4/22/2013
10-Pin
24-Pin
12
Page 7 of 25
KIA Genuine Accessories
Ratchet, Extension, 10 mm Socket and Torque Wrench
1. Secure the remote start control module to the factory stud, located on the vehicle dash wall, above the accelerator
N
pedal assembly with one (1) supplied M6 nut, as shown above.
O
2. Torque the M6 nut to 14 Nm (1.4 Kgf.m, 10 lb-ft).
T
E
Revision Date
4/22/2013
M6 Nut Torque to 14 Nm (1.4 Kgf.m, 10 lb-ft)
13
Page 8 of 25
Loading...
+ 17 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use