KI Pull Out Worksurface Storage Assembly Instructions Manual

slide rail

Assembly Instructions

Pull Out Worksurface Storage

November 2004

Kit Parts:
(1) Slide Rail
(10) #8 x

1

⁄2" Pan-Head Screws
(2) Recessed Bumpers
(2) #6 Wood Screws
(1) Wire Rack
(1) Shoulder Bolt
(2) Nylon Washers
(1) Rotating Arm Assembly
(2) Slide Guides
(1) SnapRack

TM

CD Rack (two parts

that snap together)

(1) All Terrain Bin

1. Install the Slide Rail. Hold the

slide rail on the bottom of the
work surface to be mounted.
Mark the hole locations for
mounting. Please reserve the
center screw hole on each end for
the recessed bumpers. Remove
the slide rail and pre-screw four

1

#8 x

⁄2" pan-head screws into the
work surface at both ends using
the outside two holes, then
remove. Next, hold the slide rail
in place and mount four #8 x
pan-head screws into the pre­screwed holes until flush,
continue placing the remaining
six mounting screws (Figure 1).

1

⁄2"

Figure 1

nylon washer bushing

#8 x 1/2” pan-head screw (10 req’d)

recessed bumper (2 req’d)

#6 wood screw (2 req’d)

rotating arm assembly

slide guide (2 req’d)

wire rack

2. Install Recessed Bumper. Using
one #6 wood screw, mount one
recessed bumper into the center
screw hole at far end of the slide
rail, away from the front of the
desk. This will keep the rotating
arm assembly from sliding out of
the back of the rail (Figure 1).

3. Assemble the Rotating Arm.
Place one nylon washer onto the
shoulder bolt, then place the
shoulder bolt through the bottom
of the wire rack.

Note: The wire rack is in up
position when the arc is a “U”.

Place one nylon washer onto the
opposite end of the shoulder
bolt. By hand, mount the
shoulder bolt into the end of the
rotating arm assembly, until it
catches, then using the Allen
wrench, tighten until snug. Place
one slide guide on each end of
the rotating arm assembly
(Figure 2).

flat nylon washer

5/16 shoulder bolt

Figure 2

1330 Bellevue Street • P. O. Box 8100 • Green Bay, WI 54308-8100 • Tel [phone] • www.ki.com

© 2004 KI All Rights Reserved • Litho in USA • Code KI-61645/TM/GT/1104

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and injury.

Pull Out Worksurface Storage

Assembly Instructions

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and injury.

Figure 3

recessed

bumper

rotating arm

slide rail

slide rail assembly

4. Install Rotating Arm Assembly to
Slide Rail. Slide the rotating arm
in the slide rail. Push all the way
back until it stops (Figure 3).

5. Install Last Recessed Bumper.
Using one #6 wood screw, mount
the remaining recessed bumper
in the center hole at the front end
of the slide rail (Figure 4).

6. Assemble the SnapRack

TM

CD
Rack. Snap the two sides of the
CD rack together by lining up the
snap detail at the bottom, making
a "V" shape. Place in the wire
rack assembly (Figure 5).

7. Install the All Terrain bin
(Figure 6).

Figure 4

Figure 6

SnapRack CD rack

Figure 5

snap together at the bottom