IMPULSE
SEALER
(
100H,
200H, 300H,
400H,
520H
)
\
200HC. 300HC, 400HC,
500HC
'
INSTRUCTION
MANUAL
Thanks
for
your
purchase
of
our impuse
sealers.
To
obtain
the
benefit
from
our
products.
Please
read
the following
instruction
before
operation.
HANDLE
\
TIMER
KNOB
WARNING !!
To
reduce the
risk
of shock,
disconnect
the
unit
from
the
supply circuit
before
servicing
the
replacement
of
the
heating
element.
-1-
HEATING
ADJUSTMENT
LIST
{enrlt-
trOlClfOR---'-
POLYETHYLENE
POLYPROPYLENE
OR HIGH-HEAT FILiI
UNDER 006m/m
2
UNDER 0.1m/m
3
UNDER 0.14m/m
4
UNDER 0.2mlm UNDER
0.03m/m
q
UNDER
0.044m/m
6
UNDER
0.06m/m
7
UNDER
OOBm/m
OPERATION
.
PUT
THIS MACHINE
ON
A LEVEL AND DRY
WORK TABLE.
.
PLEASE CHECK
THE VOLTAGE
OF
POWER
SOCKET, THEN INSERT
I
THE
POWER
PLUG INTO SOCKET. TRY TO PRESS DOWN
HANDLE
KNOB AND
TO EXAMINE
THE PILOT LAMP IS LIGHTING
OR
NOT.
II
.
ACCORDING
TO
MATERIAL VARIETY
AND
THICKNESS
OF
POLY-BAG,
REGULATED HEATING TIME
DURATION AT
APPROPRIATE DEGREE.
.
PUT A POLY-BAG ON
THE HEATING
ELEMENT
OF
THIS
MACHINE,
THEN PRESS DOWN HANDLE
KNOB AFTER
1.2 SECONDS,
THE
PERFECT
SEAL
APPEAR.
(SLIDE THE
KNIFE
COVER FINISHED
cuTTlNG,
200HC. 300HC.
400HC)
.
IF
THE
SEALING
APPREARANCE
IS BREAK OR DAMAGE PLEASE
REGULATE
TIMER
KNOB,
TOWARD
THE
'S"
SIDE AND TRY AGAIN
TILL THE PERFECT SEAL
APPEAR.
.IF
THE
SEALING
APPEARANCE
IS
NON-FULL.WELD,
PLEASE
REGULATE TIMER
KNOB
TOWARD
THE
"L'
SIDE AND TRY AGAIN
TILL THE PERFECT SEAL
APPEAR.
.
IF
THE POLY-BAG STICKS
TO SEALING SILICON
RUBBER.
PLEASE
SHORTEN
THE
SEALING
PRESS
TIME.
-2-
CAUTION
O
KEEP CLEAN,
ESPECIALLY
THE
CLEAN
OF HEATER
.
INSULATED
CLOTH, UPPER CLOTH AND
HEATING
ELEMENT.
.
DON'T BE WET OR HUMIDITY
FOR
THE
CAUSE
OF
ELECTRIC
OBSTACLE.
.
BEFORE
OPERATION OR
ON
OPERATION,
CHECK
HEATER
INSULATED
CLOTH
AND
UPPER
CLOTH. IF
THEY ARE
UNUSUAL,
REPLACE IT AT
ONCE,
BECAUSE
THE WORN
HEATER
INSULATED
CLOTH
AND
UPPER
CLOTH
WILL MAKE
ELECTRIC
SHORTWAY
ALSO WILL DAMAGE
TO HEATING
ELEMENT,
.
WHILE
REPLACED
HEATING ELEMENT
MUST BE
SAME
SIZE
AS
ORIGINAL.
.
WHILE
SEALING
APPEARANCE
IS
NOT ENOUGH
EXCELLENT
SHOULD
REPLACE
SEALING SILICON
RUBBER.
.
DON'T STRIKE POWERFULLY
OTHERWISE
THE
BREAKDOWN
WILL
HAPPEN.
.
WHEN USE
EXCESSIVE.
THE
TEMPERATURE
TOO
HIGH,
SUSPEND
A LITTLE
WHILE,
-3-
Loading...