Page 1
GRILL STATION
INSTALLATION INSTRUCTIONS
Page 2
2 Keystone Step-by-StepKits
VISAGE GRILL STATION
Outdoor Grill Station Kit Placement
Outdoor grill station kit may be placed directly on a
stable patio surface or be supported by a concrete
or crushed stone leveling pad below grade. Below
grade leveling pad shown here. Adjust height as
desired.
Note: See foundation layout details sheet for further
foundation information.
Safety
Glasses
BASIC TOOLS
safety alterations finishing leveling general
Gloves Mallet Caulking
Gun
Concrete
Adhesive
Level Mallet Shovel Wheelbarrow Hand
Compactor
You will need:
55 - Visage - 16"/12"unit
57 - Visage - 16"/14"unit
10 - Tubes exterior grade concrete adhesive
Crushed Aggregate - 15.28 cf
Built-in Grill*
(31"w x 21"d x 10"h rough opening)
Access Door* (15¾"w x 19½"h rough opening)
Lower Counter Material - 91¼" x 25½"
Upper Counter Material - 91¼" x 16"
Steel Lintel (shown)*
(6"wide x 41"long x 5⁄16"thick)
Note: All units are 6"h x 8"d.
*Modify rough opening sizes in both the block units
and counter top to accommodate different sized
appliances, if needed.
Concrete Saw
Wheel Grinder
Page 3
Keystone Step-by-StepKits 3
www.KeystoneRetailProducts.com
VISAGE GRILL STATION
www.KeystoneRetailProducts.com
General Note:
In consideration of freeze / thaw issues
during the cold weather season it is
recommended that this outdoor built-in
grill station element be protected from
rain, snow and ice as necessary.
Page 4
4 Keystone Step-by-StepKits
VISAGE GRILL STATION
Page 5
Keystone Step-by-StepKits 5
www.KeystoneRetailProducts.com
COURSE BY COURSE INSTRUCTIONS
On Grade Installation Note:
If the grill station is to be built on top of a stable
patio or hardscape surface, eliminate the 1st
course and base leveling pad from the grill
station design.
Appliance Service Note:
Plan and install gas and other desired utilities
prior to and during construction as needed.
Page 6
6 Keystone Step-by-Step Kits
COURSE BY COURSE INSTRUCTIONS
On Grade Installation Note:
If the grill station is to be built on top of a stable
patio or hardscape surface, eliminate the 1st
course and base leveling pad from the grill
station design.
Page 7
Keystone Step-by-Step Kits 7
www.keystonewalls.com
COURSE BY COURSE INSTRUCTIONS
Page 8
8 Keystone Step-by-Step Kits
COURSE BY COURSE INSTRUCTIONS
Block Cutting Note:
Using a concrete saw or wheel grinder tool w/
masonry disk, cut block units as needed. Block
units to be cut due to obstruction are labeled
with solid hatching. Block units to be cut to fit are
labeled with angular hatching.
Block Cutting for Appliances Note:
See appliance manufacturer’s installation
instructions for correct block cutting to allow for
proper fit for appliances.
Page 9
Keystone Step-by-Step Kits 9
www.keystonewalls.com
COURSE BY COURSE INSTRUCTIONS
Block Cutting Note:
Using a concrete saw or wheel grinder tool w/
masonry disk, cut block units as needed. Block
units to be cut due to obstruction are labeled
with solid hatching. Block units to be cut to fit are
labeled with angular hatching.
Block Cutting for Appliances Note:
See appliance manufacturer’s installation
instructions for correct block cutting to allow for
proper fit for appliances.
Page 10
10 Keystone Step-by-Step Kits
COURSE BY COURSE INSTRUCTIONS
Block Cutting Note:
Using a concrete saw or wheel grinder tool w/
masonry disk, cut block units as needed. Block
units to be cut due to obstruction are labeled
with solid hatching. Block units to be cut to fit are
labeled with angular hatching.
Block Cutting for Appliances Note:
See appliance manufacturer’s installation
instructions for correct block cutting to allow for
proper fit for appliances.
Page 11
Keystone Step-by-Step Kits 11
www.keystonewalls.com
COURSE BY COURSE INSTRUCTIONS
Block Cutting Note:
Using a concrete saw or wheel grinder tool w/
masonry disk, cut block units as needed. Block
units to be cut due to obstruction are labeled
with solid hatching. Block units to be cut to fit are
labeled with angular hatching.
Block Cutting for Appliances Note:
See appliance manufacturer’s installation
instructions for correct block cutting to allow for
proper fit for appliances.
Page 12
12 Keystone Step-by-Step Kits
COURSE BY COURSE INSTRUCTIONS
Block Cutting Note:
Using a concrete saw or wheel grinder tool w/
masonry disk, cut block units as needed. Block
units to be cut due to obstruction are labeled
with solid hatching. Block units to be cut to fit are
labeled with angular hatching.
Block Cutting for Appliances Note:
See appliance manufacturer’s installation
instructions for correct block cutting to allow for
proper fit for appliances.
Page 13
Keystone Step-by-Step Kits 13
www.keystonewalls.com
COURSE BY COURSE INSTRUCTIONS
Block Steel Lintel Cutting Note:
Prior to installing steel lintel, use a wheel grinding
tool to notch out top of block creating a level
shelf to place steel lintel, such that lintel is flush
with top of cut block. Block units to be cut for
steel lintel are shown with solid hatching.
Page 14
14 Keystone Step-by-Step Kits
COURSE BY COURSE INSTRUCTIONS
Counter Top Cutting for Appliances Note:
See appliance manufacturer’s installation
instructions for correct counter top opening sizes.
Cut to allow for proper fit for applicances. Unless
otherwise directed, use a concrete saw or wheel
grinder tool w/masonry disk to cut the counter
top as needed.
Counter Top Installation Note:
Depending on the type of counter top material
used, the counter top may be installed in multiple
pieces as needed. Joints shown with dashed lines
are suggested locations only.
Unless otherwise directed, install and secure
counter top material with a polyurethane
masonry adhesive or approved equal as per
manufacturer’s intallation instructions.
Page 15
Keystone Step-by-Step Kits 15
www.keystonewalls.com
COURSE BY COURSE INSTRUCTIONS
Counter Top Cutting Note:
Unless otherwise directed, use a concrete saw or wheel
grinder tool w/masonry disk to cut the counter top as
needed.
Counter Top Installation Note:
Depending on the type of counter top material used, the
counter top may be installed in multiple pieces as needed.
Joints shown with dashed lines are suggested locations only.
Unless otherwise directed, install and secure counter top
material with a polyurethane masonry adhesive or approved
equal as per manufacturer’s intallation instructions.
Counter Top Support Note:
Provide under counter support as needed depending on
the over hang of the counter and the type of counter top
material used.
Page 16
Keystone Retaining Wall Systems LLC
A Contech Company
4444 West 78th Street • Minneapolis, MN 55435
(952) 897-1040 • www.keystonewalls.com
©2016 Keystone Retaining Wall Systems LLC
We reserve the right to improve our products and make changes in the specifications and design without
notice. The information contained herein has been compiled by KEYSTONE and to the best of our knowledge,
accurately represents the KEYSTONE product use in the applications which are illustrated. Final determination
of the suitability for the use contemplated and its manner of use are the sole responsibility of the user.
Sbs Visage-Grill Station - 0416
Don’t forget to check out all of our Keystone Outdoor Living designs on keystonewalls.com.
Outdoor Kitchen Designs Fireplaces Columns Fire Pits Water Feature Bench
Loading...