Keystone Quick Start Guide: F02/EPI2 Quarter-Turn Electric Actuator Base and OM1 Card Manuals & Guides

Quick Start Guide

F02/EPI2 Base and OM1 Card

VCIOM-08536-US Rev. 0

F02/EPI2 Quarter-Turn
Electric Actuator

Base and OM1 Card

April 2018

Quick Start Guide

VCIOM-08536-US Rev. 0

Base Card

F02/EPI2 Quarter-Turn Electric Actuator

Rotary Switch Settings

Move switch SW4 to position

Configurations

CLOSE LIMIT by position

Drive the actuator to
the CLOSE position
using the handwheel

OPEN LIMIT by position

Drive the actuator to
the OPEN position
using the handwheel

CLOSE LIMIT by torque 2 0 (*)

OPEN LIMIT by torque 3 0 (*)

CLOSING speed 4

OPENING speed 5

% CLOSING torque 6

% OPENING torque 7

CW/CCW 8

BLINKER/local selector 4

Note:

(*) Factory

PRE-INSTALLATION: See VCIOM-2881 INSTALLATION AND MAINTENANCE INSTRUCTIONS. Not performing the following procedures will invalidate the product warranty.
INSTALLATION: To assemble the actuator onto the valve proceed as follows:

a. Verify proper mounting hardware.
b. Verify proper electrical service to the actuator
c. Lubricate the valve stem with oil or grease to make the assembly easier: pay attention not to contaminate with lubricant the ange surfaces which transmit the actuator torque.
d. Clean the valve ange and remove anything that might prevent a perfect adherence to the actuator ange and especially all traces of grease.
e. Install the actuator onto the valve so that the shaft out put drive enters the groove of the stem extension. This coupling must take place without forcing and only with the weight of the
actuator.
f. Ensure actuator and valve are in same orientation when bolting together.
g. With the handwheel, operate the actuator to verify it moves the valve smoothly.

indicated in each row

2 1 (*)

0 0

3 1 (*)

1 0

WARNING

The conguration must be done while the actuator is powered on. As a consequence, all conguration operations must be carried out by specically qualied personnel for operations on
powered electronic cards. Hazardous voltages may be present. Before connecting power to the actuator, check that the voltages are correct and according to the nameplate data. Improper power

supply will cause permanent damage to the electrical components. Actuator conguration programming requires removal of the actuator cover. Refer to VCIOM-2881 IOM for instructions.

Move switch SW6 to position

indicated in each row

4

6 (*)

8

2 = 50%
5 = 75%
9 = 100% (*)

0 = CW (*)
1 = CCW

0 = off (*)
1 = Blinker
2 = Loc. Sel.

See

table 1

SW3

Enter set up conguration moving SW3 to ON

Conrm by

SW5

PUSH

Red LED

LED lights up once

LED lights up once

Operate the
actuator to direction
bylocal/remote
control and wait
until it stops by

torque

LED lights up once

Figure 1 Model 063-125

SW3

Green LED
Power ON

Figure 2 Model 250-500-1000-2000

Exit set up conguration moving SW3 to 1 (Run Setting)

Green LED
Power ON

Table 1.

Operating Times

Nominal torque

Model

063 63/600 15 28 48

125 125/1300 15 28 48

250 250/2500 15 28 48

500 500/5100 15 28 48

1000 1000/9100 24 45 80

2000 2000/17700 53 100 180

(Nm/lb.in.)

F02/EPI2 Base and OM1 Card

April 2018

Dip switch

SW3

Rotary switch

SW4

Dip switch

SW3

Rotary switch

SW6

Push button

SW5

Red LED
Enter configuration

Rotary switch

SW6

Push button

SW5

Red LED
Enter configuration

Rotary switch

SW4

Operating time (secs 90o) at selected step

8 6 4

Quick Start Guide

Input Signal Configuration

VCIOM-08536-US Rev. 0

OM1 Card

F02/EPI2 Quarter-Turn Electric Actuator

Rotary Switch Settings

Configurations

Move switch SW8 to

position indicated in

each row

Move switch SW7 to
position indicated in

each row

Move switch SW9 to
position indicated in

each row

SW4

Conrm

by

SW2

Red LED

SW4

Figure 3

Enter
Configuration

Red LED

Rotary Switch

SW8 SW7 SW9

F02/EPI2 Base and OM1 Card

April 2018

Confirmation Push Button

SW2

SW5

RELAYS LS3-LS5 7

RELAYS LS4-LS6 8

POSITION Relays LS3 0 0 to 9 [0=(*)]

POSITION Relays LS4 1 0 to 9 [3=(*)]

POSITION Relays LS5 2 0 to 9 [7=(*)]

POSITION Relays LS6 3 0 to 9 [9=(*)]

SET Input as “4-20mA” 9

SET 0% input 4-20mA

SET 100% input 4-20mA 1 = 20mA (*)

SET Input as “0-10V”

Feedback mA or Vdc

Modulation

Table 2.

SW7 Position Relays 0 1 2 3 4 5 6 7 8 9

Description Inactive 2% 12,50% 25% 37,50% 50% 62,50% 75% 87,50% 99%

Note:

(*) Factory default data

PRE-INSTALLATION: See the BASE CARD procedure.
INSTALLATION: See the BASE CARD procedures.

WARNING

For complete Instruction & Warning see the VCIOM-01494 INSTALLATION AND MAINTENANCE INSTRUCTIONS. HARDWARE conguration MUST be done with system
OFF (NO power supply).SW3 and SW5 position in order to set the INPUT signal type.

HARDWARE conguration (SW1/3/5/6): This conguration is an Hardware setting; it’s mandatory to do it with power off (NO POWER SUPPLY)

4

9

0=break

1=make (*)

0=off

1=on (*)

0 = 4mA (*)

0=off (*)

1=on

2= mA (*)

3= Volt

0=off (*)

1=on

See table 2

Any position

4

Any position

5

1

3

Push

LED lights up once

Enter set up conguration moving SW4 to ON

Exit set up conguration moving SW4 to 1 (Run Setting)

Input Signal Configuration

Enable Configuration Mode

0-10V ON OFF OFF

4-20mA OFF ON ON

0-10V OFF ON ON OFF ON

4-20mA ON OFF OFF ON OFF

SW3

SW4

SW6 SW1

Output Signal Configuration

Hardware Configuration

Input Signal

SW3 SW5

1 2 1

Output Signal

SW1 SW6

1 2 3 4 1

World Area Con÷guration Centers (WACC) offer sales support, service,
inventory and commissioning to our global customers.
Choose the WACC or sales of÷ce nearest you:

NORTH & SOUTH AMERICA

19200 Northwest Freeway
Houston TX 77065
USA
T [phone]

Av. Hollingsworth
325 Iporanga Sorocaba
SP 18087-105
Brazil

MIDDLE EAST & AFRICA

P. O. Box 17033
Jebel Ali Free Zone
Dubai
T [phone]

P. O. Box 10305
Jubail 31961
Saudi Arabia
T [phone]

T [phone]

24 Angus Crescent

ASIA PACIFIC

Longmeadow Business Estate

East
No. 9 Gul Road
#01-02 Singapore 629361
T [phone]

P.O. Box 6908 Greenstone

1616 Modderfontein Extension 5

South Africa

T [phone]

No. 1 Lai Yuan Road
Wuqing Development Area

Tianjin 301700
P. R. China
T [phone]

EUROPE

Holland Fasor 6

Székesfehérvár 8000

Hungary

T [phone]

Strada Biffi 165

29017 Fiorenzuola d’Arda (PC)

Italy

T [phone]

For complete list of sales and manufacturing sites, please visit

www.emerson.com/actuationtechnologieslocations

Or contact us at info.actuation [e-mail]

www.emerson.com

©2018 Emerson. All rights reserved.

The Emerson logo is a trademark and service mark of Emerson Electric Co.

The contents of this publication are presented for information purposes
only, and while every effort has been made to ensure their accuracy,
they are not to be construed as warranties or guarantees, express or
implied, regarding the products or services described herein or their
use or applicability. All sales are governed by our terms and conditions,

which are available on request. We reserve the right to modify or
improve the designs or specications of our products at any time

without notice.