Keystone Manual: DF Butterfly Valves Figure 631 - larger sizes - Repair Instructions, Keystone-EN Manuals & Guides
1 4
1918
15 12 11
KEYSTONE FIGURE 631 PN16 DOUBLE FLANGED BUTTERFLY VALVE
REPAIR AND MAINTENANCE INSTRUCTIONS
Complete assembly and disassembly instructions for 600 - 1050 mm
F631 PN16 double flanged butterfly valves
SAFETY PRECAUTIONS
Whenever a valve is being installed or removed
from the pipeline, ensure the line is not
pressurized and any hazardous medium is
drained away.
Before carrying out any maintenance where the
valves are either pnuematically or electrically
actuated be sure to close/isolate the air supply
and exhaust the pressure to the actuator OR
ensure the electrical supply is disconnected by
authorized personnel.
DISASSEMBLY INSTRUCTIONS
1. Turn the disc (2) to the 5° open position.
2. Remove the actuator from the valve, if you
have not already done so.
3. Undo disc pin nuts (9) then remove disc
pins(8).
4. Remove end cover (11) by undoing the four
(4) end cover bolts (19) and then remove end
cover O-ring (18) and thrust washer (12).
5. Remove gland bush O-ring outer (17), gland
bush (14) and gland bush O-ring inner (16).
6. Remove shaft (3) carefully, ensuring not to
scrape shaft against the shaft bore.
Note position of keyway in relation to the
actuator.
7. Twist disc (2) to the fully open position then
roll the disc out of the seat, ensuring not to
damage the disc edge.
8. Collapse seat (4) to the center of the valve
bore at the O-ring housing spigots (shaft
holes) and gently lever one side of the seat
from the flange face, then pull through
when the seat is clear of the bed groove.
Donot use any sharp tools to aid removal
ofseat.
9. Remove upper and lower bearings (15) for
inspection.
10. Thoroughly clean all components and
examine them for excessive wear or
damage. It is recommended that all O-rings
be replaced and all seats, bushes, plugs etc.
are free from damage burrs etc.
MAINTENANCE
Routine maintenance or lubrication are not
required.
REMOVAL INSTRUCTIONS
If it is necessary to replace components,
thevalve must be removed from the pipe.
1. Partially open valve (5°open).
2. Disconnect any power supplies.
3. Remove flange bolts.
4. Spread flanges and remove valve.
14
16
www.valves.emerson.com © 2017 Emerson. All rights reserved.
31517
9
8
2
VCIOM-03014-EN 16/09
KEYSTONE FIGURE 631 PN16 DOUBLE FLANGED BUTTERFLY VALVE
REPAIR AND MAINTENANCE INSTRUCTIONS
1 4
14
16
31517
ASSEMBLY INSTRUCTIONS
1. Check all components are clean and free of
damage.
2. Fit seat insert O-rings (6) into seat inserts(5)
encapsulated in the seat (300 to 500 only).
3. Collapse the seat (4) and push into the bore
of the valve, aligning the seat inserts (5)
with the shaft bore. Ensuring O-rings are
still in position, locate spigot in shaft bore
at the hub end, then gently push seat(4)
into bedgroove simultaneously on both
sides, working your way up to the top shaft
bore. Then ensure the remaining spigot is
correctly positioned. Inspect the seat(4)
to ensure that it is sitting evenly in the
bedgroove and apply pressure with thumbs
at the spigots to ensure correct fitand that
the seat is sitting evenly on the flange face.
4. Fit inner and outer gland bush
O-ring(16),(17) either side of gland
bush(14).
5. Fit upper and lower bearings (15).
15 12 11
1918
10
8
9
2
6. Insert the shaft (3) into the neck of the valve
and stop prior to entering the valve bore.
7. Roll disc (2) into the seat leading with the
disc edge (ensuring not to damage the edge)
with the disc screw holes closest to the neck
of the valve, then twist disc until the shaft
holes are aligned.
8. Push shaft (3) downwards through the
disc(2) into the hub of the valve until the
disc screw holes are aligned. A twisting
motion while pushing down will aid with
smooth insertion.
9. Fit disc pins (8), push on disc pin
O-ring(10),one on each side, and tighten
disc pin nuts (9) to 20 Nm.
10. Replace thrust washer (12), O-ring (18) and
end cover (11) then secure by means of the
four bolts (19).
11. Slowly actuate valve to ensure all
components are free and correctly aligned.
12. Assembly is now complete and the valve is
ready for installation or storage.
Refer to F631 Installation Instructions for
details.
© 2017 Emerson. All rights reserved.
2
Loading...