Page 1
Instruction Manual
ETLus Electric Fan
KSTFA120AG
For Household Use Only
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
This fan has a polarized plug (one blade is wider than the other). To reduce the
risk of electric shock, this plug is intended to fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not attempt to defeat this safety feature.
This product employs overload protection (fuse). A blown fuse indicates an
overload or short-circuit situation. If the fuse blows, unplug the product from the
outlet. Replace the fuse as per the user serv icin g instructions (follow product
marking for proper fuse rating) and check the prod uct, If the replacement fuse
blows, a short-circuit may be present and the produ ct should be discarded or
returned to an authorized service facility for ex amination and/or repair.
WARNING – To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This
Fan With Any Solid-State Speed Control Device.
WARNING – To Reduce The Risk Of Electric Shock, Do Not Expose to Water
or Rain.
WARNING – This is a fan – not a toy! To reduce the risk of personal injury and
electric shock, it should not be played with or placed where small children can
reach it.
When using electric appliances, basic safety pre cau tions should always be
followed, including the following:
1. Do unplug or disconnect the appliance from the power supply be fo re servicing.
2. Do not use gasoline, thinners, solvents, ammonias or other chemicals for
cleaning.
3. Do clean your fan regularly. Refer to the Cleaning instructions provided. Never
clean the fan in any manner other than as instructed in this manual.
4. Do not operate any fan with a damaged cord or plug. Dis card fan or return to
an authorized service facility for examination and/or repair.
5. Do not run cord under carpeting. Do not cov er cord with throw rugs, runners,
or similar coverings. Do not route cord under furniture or app lia nces. Arrange
cord away from traffic area and where it will not be tripped over.
6. Do not use this product outdoors.
7. Do not use this product on wet surfaces.
8. Do not use this product in a bathtub or shower.
9. Do not use near furnaces, fireplaces, stove or other high-temperature heat
sources.
10. Do not immerse this product in water or allow water to drip into the motor
housing.
11. Do not position this fan too close to draperies because they may be drawn into
the rear guard, cutting off airflow.
SAVE THESE INSTRUCTIONS
User Servicing Instructions
P1-14606
P2-14606
Page 2
Grasp plug and remove from the receptacle or other outlet device. Do not unplug
by pulling on cord. Open fuse cover (A.) by sliding access cover on top of
attachment plug towards blades. Remove f use care fully (B.) by gently prying out
the ends of the fuse from the receptacle.
Risk of fire. Replace fuse only with 2.5 Amp, 125 Vo lt fuse.
Install replacement fuse (C.) by first placing the end of the fuse into the fuse
receptacle which is opposite of the blades of the plug, then carefully push in the
other end. Only push against the metal end of the fu se, not the glass center
portion. Close the fuse access cover (D.) by sliding the cov er back into the plug
until it is completely closed, latches and is flush with the face of the plug.
Risk of fire. Do not replace attachment plug. Contains a safety device (fuse , AFCI,
LCDI) that should not be removed. Discard product if the attachment plug is
damaged.
Know Your Fan
Parts and Their Function
Parts Function
●Height adjust button
Use only when higher position required.
Pressing the height adjust button, pull
the slide pipe upwards.
When lower position required, just push
the slide pipe downwards.
You can adjust the height in 2 steps.
Caution: Be careful not to pinch fingers.
●Swivel button
Press down…Swivel starts
Pull up…Swivel stops
How to Assemble
P4-14606
P3-14606
P4-14606
Page 3
CAUTION:
Do not insert the plug into the power point before assembly is complete.
(May cause electric shock or injury)
Do not press height adjustment button while fan and fan guard are
detached.
(The motor section (slide pipe) may jump out of stand, causing injury)
1. Fix the stand onto the base
●Remove the motor shaft cover.
●Check the stand direction by the
indication of front and back of
the base and stand, insert the front
protusions of stand into the concav
-es of the base, then push the
whole stand part down onto the
base until it is fitted in firmly.
●Placing the motor shaft upward,
then fix the stand and base by
turning the base fixing ring
provided clockwise.
Attention:
● Base fixing ring is temporarily attached on bottom of stand. Unscrew it
When you assemble the fan.
● Do not forcibly push the stand down onto the base. May cause damage.
● Do not put the stand onto the base in wrong direction. May cause damage.
● Do not press the height adjust button while assemb lin g. May cause injury,
damage to the product or machine failure.
2. Fix Rear Guard and Fan Blade
●Couple protrusions (three) on the motor sec tion to concaves (three) on the
rear guard.
●Fix them firmly by turning the guard fixing ring toward [fasten].
●Couple the pin on the motor shaft and the concave on the fan blade and
insert the fan part into the motor part. Then pressing the fan part towards
the motor part and turn the fan blade cap toward [fasten] to fix them firmly.
Attention:
● If the fan blade cap is not fastened firmly enough, fan blade may come off,
causing injury.
● Be careful not to be injured by motor shaft or pin when assembling or
disassembling.
3. Fix Front Guard
●Hold the rear guard and press the front guard
toward the rear guard from the top, making sure
that the whole periphery of the front gu ard clicks
into the rear guard.
●Clip the front and rear guard together
with the clip on the guard.
Attention:
● If the front guard is not clip pe d together
firmly enough, the front guard may come off , cau sin g in jury.
How to Take off Front Guard
Unplug first and stop the ratation of the fan blade. Then undo the clip and pull the
grip on the guard ring, pressing the front guard down.
Attention: Do not pull by the clip. May damage the clip.
P5-14606
P6-14606
Page 4
How to Operate
SPEED
STOP/ LOW - MID - HIGH
ON TIMER
Select TIMER ON (0 -0.5-1.0-1.5-2.0-2.5-3.0 Hour)
OFF TIMER
Select TIMER OFF
Ready
Insert the power plug into a 120V power point.
Start (speed setting)
Switch on by pushing [LOW - MID - HIGH] button.
Pushing [STOP] button to end the operation.
Timer setting
Turn timer on, select at your desired time (0 -0.5-1.0-1.5-2.0-2.5-3.0 Hour).
(After the time you set, the fan will stop automatically)
When the timer is set [TIMER OFF], will stop timer function.
Tilting Adjustment
Always switch the fan off before making a tilt adjustment. The air flow can be
adjusted upward or downward simply by moving the guard up or down.
CAUTION:
In the case of no blades installed, Please don't run the product.
Maintenance and Storage
WARNING
When cleaning, the plug must be removed from the power point. Do not
handle plug with wet hands.
[May cause electric shock or injury.]
Do not press the height adjustment butt o n while the fan and fan guard are
detached.
[The motor section (slide pipe) may jump out of the stand pa rt, causing injury.]
When disassembling the base or stand, unplug plug from the power point.
[May cause electric shock or injury.]
How to Clean
Disassemble the fan and guard in the inverse order of as sembling. Wash off dirt
and dust with well squeezed wet soft cloth with water or neutral detergent, then
wipe off the detergent.
CAUTION:
Do not use volatile solvents such as gasoline, thinner, benzene, wax,
kerosene, alcohol, polishing powder, or alkaline detergent. These may
discolour or damage the machine, causing injury.
If using a chemical dust cloth, follow those instruct ion .
Do not oil plastic parts. May cause discoloration or injury from damaged parts.
How to Store
Disassemble fan, guard, stand and base in the inverse order of assembling.
Clean the motor shaft and oil put the motor shaft cover back to the motor shaft.
Store these parts in the box provided at purchase and keep in a dry place.
CAUTION:
When the fan is not facing front, do not force the fan to turn. Use the swiv el
function.
Clean the fan and guard referrring to [ How to Clean], then store it.
How to Disassemble the Base
P8-14606
P7-14606
Page 5
1. Put the motor shaft upward, then unscrew f i x i n g rin g b y turning anticlockwise.
(Refer to the drawing at below)
Holding the base firmly, then pull the base.
CAUTION:
If the motor shaft is facing downward, the fan will become unstable and may
damage the product or floor.
When putting the motor shaft down, the fan is unstable. May cause machine
failure and damage to floor.
2. Hold the stand firmly and gently lift and remove the base.
Technical Specifications
V
oltage
120V~60Hz
Power Consumption
?A or ?W
Fan Speed
STOP/ LOW - MID - HIGT
Timer
0 -0.5-1.0-1.5-2.0-2.5-3.0 Hour
P9-14606
Loading...