Page 1
Instruction Manual
ETLus Electric Fan
KSTFA070AG
For Household Use Only
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
This fan has a polarized plug (one blade is wider than the other). To reduce the
risk of electric shock, this plug is intended to fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not att empt to defeat this safety feature.
This product employs overload protection (fuse). A blown fuse indicates an
overload or short-circuit situation. If th e fuse blows, unplug the product from the
outlet. Replace the fuse as per the user servicin g in structions (follow product
marking for proper fuse rating) and check the product, If the replacement fuse
blows, a short-circuit may be present and the produ ct sh ou ld be discarded or
returned to an authorized service facility for ex amination and/or repair.
WARNING – To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This
Fan With Any Solid-State Speed Control Device.
WARNING – To Reduce The Risk Of Electric Shock, Do Not Expose to Water
or Rain.
WARNING – This is a fan – not a toy! To reduce the risk of personal inju ry
and electric shock, it should not be played with or placed where small children can
reach it.
When using electric appliances, basic safety precautions should always be
followed, including the following:
1. Do unplug or disconnect the appliance from the power supply before servicing.
2. Do not use gasoline, thinners, solvents, ammonias o r ot her chemicals for
cleaning.
3. Do not operate any fan with a damaged cord or plug. Di scard fan or return to
an authorized service facility for examination and/or repair.
4. Do not run cord under carpeting. Do not cov er cord with throw rugs, runners,
or similar coverings. Do not route cord under furniture or applia nces. Arrange
cord away from traffic area and where it will not be tripped over.
5. Do not use this product outdoors.
6. Do not use this product on wet surfaces.
7. Do not use this product in a bathtub or shower.
8. Do not use near furnaces, fireplaces, stove or other high-temperature heat
sources.
9. Do not immerse this product in water or allow water to drip into the motor
housing.
SAVE THESE INSTRUCTIONS
P1-14606
P2-14606
Page 2
User Servicing Instructions
Grasp plug and remove from the receptacle or other outlet device. Do not unplug
by pulling on cord. Open fuse cover (A.) by sliding access cover on top of
attachment plug towards blades. Remove fuse carefully (B.) by gently prying out
the ends of the fuse from the receptacle.
Risk of fire. Replace fuse only with 2.5 Amp, 125 Vo lt fuse.
Install replacement fuse (C.) by first placing the end of the fuse into the fuse
receptacle which is opposite of the blades of the plug, then carefully push in the
other end. Only push against the metal end of the fuse, not the glass center
portion. Close the fuse access cover (D.) by sliding the cover back into the plug
until it is completely closed, latches and is flush with the face of the plug.
Risk of fire. Do not replace attachment plug.
Contains a safety device (fuse, AFCI, LCDI) that should not be removed.
Discard product if the attachment plug is damaged.
Know Your Fan
Parts and Features
Swing Control and Tilting Adjustment
Press down…Swivel starts.
Pull up…Swivel stops.
Always switch the fan off
before making a tilt adjustment.
The air flow can be adjusted
upward or downward simply by
moving the guard up or down.
P414606
P3-14606
Page 3
How to Operate
OFF/ ON
Operation 0(OFF), 1(LOW), 2(HIGH)
TIMER ON
Select TIMER ON (1min ~ 180min)
TIMER OFF
Select TIMER OFF
Ready
Insert the power plug into power point.
Start
Rotating [0 - 1 - 2], select speed 1(LOW), 2(HIGH).
Timer setting
Rotating [TIMER ON], select time (30 min~180min).
Until [TIMER OFF], the fan is not operated.
Maintenance and Storage
WARNING
When clearing, the plug must be removed from the power point. Do not handle
plug with wet hands.
[May cause electric shock or injury.]
How to Clean
Use in a dry place, free of excessive humidity and wate r.
Keep fan clean, wipe away dirt with a clean cloth.
Use a vacuum cleaner to clean the front grid and blade. Do not use gasoline
or thinner to clean fan.
Before putting the fan in storage, clean thoroughly then cover with a vinyl bag
and store in a dry place.
CAUTION:
Do not use volatile solvents such as gasoline, thinner, benzene, wax,
kerosene, alcohol, polishing powder, or alkaline detergent. These may
discolour or damage the machine, causing injury.
If using a chemical dust cloth, follow those instruction .
Do not oil plastic. May cause discoloration or injury from damaged parts.
When the fan is not facing front, do not force the fan to turn. Use the swivel
function.
Clean the fan and guard referrring to [ How to Clean], then store it.
How to Remove Front Guard for Cleaning
1. Use tool to unlock the screw of the guard, turn counter clockwise remove the
front guard.
2. After cleaning, turn clockwise to assemble the front gu ard, and use tool to lock
the screw of the guard.
Technical Specifications
V
oltage
120V~60Hz
Power Consumption
?A or ?W
Fan Speed
OFF/ON, TIMER ON, TIMER OFF
Timer
1min ~ 180min
Product HolderJoin-One Electric (Shenzhen) Co.,Ltd
Subject to technical modification
P5-14606
P6-14606
Loading...