Keysight (Agilent) P281C Data Sheet

Agilent Technologies
X/P/K281C Adapters

Including Options 006, 012, 013

Operating and
Service Manual

Agilent Part Number: 00281-90043
Printed in USA
Print Date: April 2002

Supersedes: June 2001

Notice

The information contained in this document is subject to change without
notice.

Agilent Technologies makes no warranty of any kind with regard to this
material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. Agilent Technologies
shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or
use of this material.

Agilent Technologies assumes no responsibility for the use or reliability of
its software on equipment that is not furnished by Agilent Technologies.

This document contains proprietary information which is protected by
copyright. All rights are reserved. No part of this document may be
photocopied, reproduced, or translated to another language without prior
written consent of Agilent Technologies.

Restricted Rights Legend

Use, duplication, or disclosure by the U.S. Government is subject to
restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical
Data and Computer Software clause at DFARS 252.227-7013 for DOD
agencies, and subparagraphs (c)(1) and (c)(2) of the Commercial Computer
Software Restricted Rights clause at FAR 52.227-19 for other agencies.

Agilent Technologies, Inc.
1400 Fountaingrove Parkway
Santa Rosa, CA 95403-1799, U.S.A.

© Copyright 1996, 1999, 2001, 2002 Agilent Technologies, Inc.

ii X/P/K218C Operating and Service Manual

Warranty

Certification Agilent Technologies certifies that this product met its published specifications at the time of

shipment from the factory. Agilent Technologies further certifies that its calibration
measurements are traceable to the United States National Institute of Standards and
Technology (NIST, formerly NBS), to the extent allowed by the Institute’s calibration facility,
and to the calibration facilities of other International Standards Organization members.

Documentation Warranty

THE MATERIAL CONTAINED IN THIS DOCUMENT IS
PROVIDED "AS IS," AND IS SUBJECT TO BEING CHANGED,
WITHOUT NOTICE, IN FUTURE EDITIONS. FURTHER, TO
THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW,
AGILENT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS
OR IMPLIED WITH REGARD TO THIS MANUAL AND ANY
INFORMATIONCONTAINEDHEREIN,INCLUDING BUTNOT
LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. AGILENT SHALL NOT BE LIABLE FOR ERRORS
OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN
CONNECTION WITH THE FURNISHING, USE, OR
PERFORMANCE OF THIS DOCUMENT OR ANY
INFORMATION CONTAINED HEREIN. SHOULD AGILENT
AND THE USER HAVE A SEPARATE WRITTEN AGREEMENT
WITH WARRANTY TERMS COVERING THE MATERIAL IN
THIS DOCUMENT THAT CONFLICT WITH THESE TERMS,
THE WARRANTY TERMS IN THE SEPARATE AGREEMENT
WILL CONTROL.

X/P/K218C Operating and Service Manual iii

Assistance Product maintenance agreements and other customer assistance agreements

are available for Agilent Technologies products.
For assistance, call your local Agilent Technologies Sales and Service Office

(refer to “Service and Support” on page iv).

Service and Support

By internet, phone, or fax, get assistance with all your test and measurement needs.

Online assistance: www.agilent.com/find/assist
United States

(tel) 1 800 452 4844

New Zealand

(tel) 0 800 738 378
(fax) ([phone]

Latin America

(tel) [phone]
(fax) [phone]

Japan

(tel) ([phone]
(fax) ([phone]

Canada

(tel) 1 877 894 4414
(fax) [phone]

Australia

(tel) 1 800 629 485
(fax) ([phone]

Europe

(tel) ([phone]
(fax) ([phone]

Asia Call Center Numbers

Country Phone Number Fax Number

Singapore 1-800-375-8100 (65) 836-0252
Malaysia 1-800-828-848 1-800-801664
Philippines (632) 8426802

1-800-16510170 (PLDT
Subscriber Only)

Thailand [phone] (outside Bangkok)

[phone] (within Bangkok)

Hong Kong 800-930-871 (852) 2506 9233

(632) 8426809
1-800-16510288 (PLDT
Subscriber Only)

(66) 1-661-3714

Taiwan 0800-047-866 (886) 2 25456723
People’s Republic

of China
India 1-600-11-2929 000-800-650-1101

800-810-0189 (preferred)
10800-650-0021

10800-650-0121

iv X/P/K218C Operating and Service Manual

Safety and Regulatory Information

Review this product and related documentation to familiarize yourself with
safety markings and instructions before you operate the instrument. This
product has been designed and tested in accordance with international
standards.

WARNING The WARNING notice denotes a hazard. It calls attention to a procedure,

practice, or the like, that, if not correctly performed or adhered to, could result
in personal injury. Do not proceed beyond a WARNING notice until the
indicated conditions are fully understood and met.

CAUTION The CAUTION notice denotes a hazard. It calls attention to an operating

procedure, practice, or the like, which, if not correctly performed or adhered
to, could result in damage to the product or loss of important data. Do not
proceed beyond a CAUTION notice until the indicated conditions are fully
understood and met.

Instrument Markings

1SM1-A This text indicates that the instrument isan Industrial Scientific and Medical Group 1

When you see this symbol on your instrument, you should refer to the instrument’s

!

instruction manual for important information.

This symbol indicates hazardous voltages.

The laser radiation symbol is marked on products that have a laser output.

This symbol indicates that the instrument requires alternating current (ac) input.

The CE mark is a registered trademark of the European Community. If it is
accompanied by a year, it indicates the year the design was proven.

The C-Tick mark is a registered trademark of the Australian Spectrum Agency.

The CSA mark is a registered trademark of the Canadian Standards Association.

Class A product (CISPER 11, Clause 4).

X/P/K218C Operating and Service Manual v

This ISM devise complies with Canadian ICES-001.
Cet appareil ISM est conforme a la norme NMB du Canada

This symbol indicates that the power line switch is ON.

This symbol indicates that the power line switch is OFF or in STANDBY position.

Safety Earth Ground

This is a Safety Class I product (provided with a protective earthing
terminal). An uninterruptible safety earth ground must be provided from the
main power source to the product input wiring terminals, power cord, or
supplied power cord set. Whenever it is likely that the protection has been
impaired, the product must be made inoperative and secured against any
unintended operation.

BeforeApplying Power Verify that the product is configured to match the available main power

source as described in the input power configuration instructions in this
manual. If this product is to be powered by autotransformer, make sure the
common terminal is connected to the neutral (grounded) side of the ac power
supply.

vi X/P/K218C Operating and Service Manual