Keysight (Agilent) 86100C Getting Started

Infiniium DCA-J
Agilent 86100C
Wide-Bandwidth
Oscilloscope

Quick Start Guide

Agilent Technologies

Notices

© Agilent Technologies, Inc. 2000-2007

No part of this manual may be reproduced in any
form or by any means (including electronic stor­age and retrieval or translation into a foreign lan­guage) without prior agreement and written
consent from Agilent Technologies, Inc. as gov­erned by United States and international copy­right lays.

Manual Part Number

86100-90094

Technology Licenses

The hardware and/or software described in this
document are furnished under a license and may
be used or copied only in accordance with the
terms of such license.

LZW compression/decompression: Licensed
under U.S. Patent No. 4,558,302 and foreign
counterparts. The purchase or use of LZW graph­ics capability in a licensed product does not
authorize or permit an end user to use any other
product or perform any other method or activity
involving use of LZW unless the end user is sepa­rately licensed in writing by Unisys.

Trademark Acknowledgements

Microsoft is a U.S. registered trademark of
Microsoft Corporation.

Windows and MS Windows are U.S. registered
trademarks of Microsoft Corporation.

MATLAB ® is a U.S. registered trademark of The
Math Works, Inc.

Edition

March 2007
Printed in Malaysia

Agilent Technologies, Inc.
Digital Signal Analysis Division
1400 Fountaingrove Parkway
Santa Rosa, CA 95403, USA

Warranty

The material contained in this document is pro­vided “as is,” and is subject to being changed,
without notice, in future editions. Further, to the
maximum extent permitted by applicable law,
Agilent disclaims all warranties, either express or
implied, with regard to this manual and any infor­mation contained herein, including but not limited
to the implied warranties of merchantability and
fitness for a particular purpose. Agilent shall not
be liable for errors or for incidental or consequen­tial damages in connection with the furnishing,
use, or performance of this document or of any
information contained herein. Should Agilent and
the user have a separate written agreement with
warranty terms covering the material in this docu­ment that conflict with these terms, the warranty
terms in the separate agreement shall control.

Restricted Rights Legend

If software is for use in the performance of a U.S.
Government prime contract or subcontract, Soft­ware is delivered and licensed as “Commercial
computer software” as defined in DFAR 252.227­7014 (June 1995), or as a “commercial item” as
defined in FAR 2.101(a) or as “Restricted com­puter software” as defined in FAR 52.227-19
(June 1987) or any equivalent agency regulation
or contract clause. Use, duplication or disclosure
of Software is subject to Agilent Technologies’
standard commercial license terms, and non-DOD
Departments and Agencies of the U.S. Govern­ment will receive no greater than Restricted
Rights as defined in FAR 52.227-19(c)(1-2) (June

1987). U.S. Government users will receive no
greater than Limited Rights as defined in FAR

52.227-14 (June 1987) or DFAR 252.227-7015
(b)(2) (November 1995), as applicable in any tech­nical data.

Safety Notices

CAUTION

Caution denotes a hazard. It calls attention to a
procedure which, if not correctly performed or
adhered to, could result in damage to or destruc­tion of the product. Do not proceed beyond a cau­tion sign until the indicated conditions are fully
understood and met.

WARNING

Warning denotes a hazard. It calls attention to
a procedure which, if not correctly performed or
adhered to, could result in injury or loss of life. Do
not proceed beyond a warning sign until the indi­cated conditions are fully understood and met.

ii

Contents

1 Installing the 86100C

Installing the 86100C 1–2
Connector Care 1–37
Returning the Instrument for Service 1–42

2 Using the 86100C

A Quick Tour 2–2
Eye/Mask Mode 2–8
Jitter/Amplitude Analysis Mode 2–11
Oscilloscope Mode 2–13
TDR/TDT Mode 2–14
Quick Measure 2–15
Optional Features and Licenses 2–16
Windows XP Professional 2–19
If the Infiniium DCA has a Problem 2–22

3 Using the Built-In Information System

Using the Built-In Information System 3–2
Getting Help While Changing Instrument Settings 3–4
Learning About Measurement Results 3–5
Printing Topics 3–6

4 Working in Comfort

Working in Comfort 4–2

Contents-1

Contents

Contents-2

1

Installing the 86100C 1-2

Step 1. Inspect the shipment 1-5
Step 2. Position the Infiniium DCA 1-7
Step 3. Install the modules 1-8
Step 4. Connect the keyboard and mouse 1-9
Step 5. Connect a printer (Optional) 1-10
Step 6. Connect the power 1-11
Step 7. Windows Setup Wizard 1-14
Step 8. Change removable hard disk (Option 86100C-090) 1-18
Step 9. Install a feature license (Optional) 1-19
Step 10. Calibrate the touch screen 1-22
Step 11. Avoid costly repairs 1-24
Step 12. Calibrate the modules 1-25
To configure a LAN connection 1-28
To use the removable hard disk option 1-30
To connect an external display 1-35

To clean the 86100C 1-36
Connector Care 1-37
Returning the Instrument for Service 1-42

Installing the 86100C

Installing the 86100C

Installing the 86100C

Installing the 86100C

This chapter shows you how to properly set up your 86100C. Follow the steps
in the order presented. In addition, you will learn about care and use of elec­trical and optical connections.

Figure 1-1. 86100C Front Panel

General Safety
Considerations

NOTE Install the instrument according to the enclosure protection provided. This

This product has been designed and tested in accordance with the standards
listed in the Manufacturer’s Declaration of Conformity, and has been supplied
in a safe condition. The documentation contains information and warnings
which must be followed by the user to ensure safe operation and to maintain
the product in a safe condition.

instrument does not protect against the ingress of water. This instrument pro­tects against finger access to hazardous parts within the enclosure.

1-2

Installing the 86100C

Installing the 86100C

WARNING If this product is not used as specified, the protection provided by the

equipment could be impaired. This product must be used in a normal
condition (in which all means for protection are intact) only.

WARNING No operator serviceable parts inside. Refer servicing to qualified

service personnel. To prevent electrical shock do not remove covers.

WARNING This is a Safety Class 1 Product (provided with a protective earthing

ground incorporated in the power cord). The mains plug shall only be
inserted in a socket outlet provided with a protective earth contact.
Any interruption of the protective conductor inside or outside of the
product is likely to make the product dangerous. Intentional
interruption is prohibited.

CAUTION VENTILATION REQUIREMENTS: When installing the product in a cabinet, the

convection into and out of the product must not be restricted. The ambient
temperature (outside the cabinet) must be less than the maximum operating
temperature of the product by 4° C for every 100 watts dissipated in the
cabinet. If the total power dissipated in the cabinet is greater than 800 watts,
then forced convection must be used.

CAUTION This product is designed for use in INSTALLATION CATEGORY II and

POLLUTION DEGREE 2 per IEC 1010 and 664 respectively.

Installation Category: Installation Categories (overvoltage categories) are
determined by the transient overvoltage levels that may be expected. CAT I:
Mains isolated. CAT II: Line voltage in appliance and to wall outlet. CAT III:
Line voltage behind wall outlet to next level of distribution.

Instrument Markings The instruction manual symbol. The product is marked with this warn-

ing symbol when it is necessary for the user to refer to the instructions
in the manual.

The laser radiation symbol. This warning symbol is marked on products
which have a laser output.

ON, ❘, OFF, ❍

The ON, ON, STANDBY, OFF, OFF and AC symbols.

The ON, OFF, and STANDBY mark the position of the
instrument power line switch. The AC symbol is used to indicate the required
nature of the line module input power.

The CE mark is a registered trademark of the European Community.

The CSA mark is a registered trademark of the Canadian Standards
Association.

1-3

Installing the 86100C

Installing the 86100C

The C-Tick mark is a registered trademark of the Australian Spectrum
Management Agency.

This product complies with the WEEE Directive (2002/96/EC) mark­ing requirements. The affixed label indicates that you must not dis­card this electrical/electronic product in domestic household waste.

Product Category: With reference to the equipment types in the
WEEE Directive Annex I, this product is classed as a “Monitoring and Control
instrumentation” product. Do not dispose in domestic household. To return
unwanted products, contact your local Agilent office, or refer to www.agi­lent.com for more information.

This text denotes the instrument is an Industrial Scientific and Medical

ISM1-A

Group 1 Class A product.

ICES / NMB-001

This is a marking to indicate product compliance with the Cana­dian Interference-Causing Equipment Standard.

1-4

Step 1. Inspect the shipment

❒ Inspect the shipping container and instrument for damage.

Keep the shipping container and cushioning material until you have inspected
the contents of the shipment for completeness and have checked the instru­ment mechanically and electrically.

❒ Locate the shipping list. Verify that you received all the accessories on this list,

and all the options that you ordered. The following list shows some of the items
that may be on the shipping list. The information on your actual shipping list is
more accurate and should supersede the information in this list.

Package Contents • Infiniium DCA

• Keyboard, USB

• Mouse, USB

• Flash drive, USB

• Two power cords

• APC 3.5 (f-f) adapter/connector saver (p/n 5061-5311)

• Quick Start Guide (this book)

Installing the 86100C

Step 1. Inspect the shipment

Optional Accessories • Programmer’s Guide

• External CD-RW drive, USB

• Filler panel 86101-60005

• 11667B Power splitter, dc to 26.5 GHz, APC 3.5 mm

• 11667C Power splitter, dc to 50 GHz, 2.4 mm

• 54006A 6 GHz Resistive divider probe kit

• 54008B 24 ns delay line

• 83440B/C/D Optical-to-Electrical Converters (6/20/34 GHz)

• N1020A 6 GHz TDR probe kit (passive)

• N1022A Active Probe Adapter

• N1024A TDR Calibration Kit

• N1025A 1 GHz Active Differential Probe

Optional Adapters for
Electrical Channel
Inputs

Optional Adapters for
Optical Channel
Inputs

• SMA (f-f) adapter, Agilent part number 1250-1158

• APC 3.5 (f-f) adapter, Agilent part number 5061-5311

Table 1-1 shows the available fiber-optic adapters for optical channels. These

adapters connect onto the front-panel optical channel connectors. FC/PC
adapters come preinstalled on new optical modules. Changing fiber-optic

1-5

Installing the 86100C

Step 1. Inspect the shipment

adapters is easy. Simply hand turn an adapter counter-clockwise to remove it
from a channel connector; to install a different adapter, hand turn the new
adapter clockwise onto the connector.

Table 1-1. Fiber-Optic Adapters for Optical Channels

Front Panel
Fiber-Optic Adapters Description Agilent Part Number

Diamond HMS-10 81000AI

FC/PC 81000FI

SC 81000KI

DIN 81000SI

ST 81000VI

Instrument Options • 86100C-001, Enhanced 12.5 GHz Trigger Bandwidth, providing pattern lock

and eyeline capabilities.

• 86100C-090, Removable hard disk

• 86100C-092, Standard instrument internal non-removable hard disk.

• 86100C-200, Enhanced Jitter Analysis Software

• 86100C-201, Advanced Waveform Analysis Software

• 86100C-202, Enhanced Impedance and S-Parameter Software

• 86100C-300, Advanced Amplitude Analysis/RIN/Q-Factor

• 86100C-0BJ, Programmer’s Guide

• 86100C-AFP, Additional filler panel

• 86100C-AX4, Rack mount flange kit

• 86100C-AXE, Rack mount flange kit with handles

• 86100C-UK6, Commercial calibration certificate with test data

If anything is missing or defective, refer to “Contacting Agilent Technologies”

on page 1-42. If the shipment was damaged, contact the carrier, then contact

the nearest Agilent Sales Office. Keep the shipping materials for the carrier’s
inspection. The Agilent Sales Office will arrange for repair or replacement at
Agilent’s option without waiting for claim settlement.

1-6

Installing the 86100C

Step 2. Position the Infiniium DCA

Step 2. Position the Infiniium DCA

Position the Infiniium DCA so that it will have sufficient clearance for airflow
around the top, back, and sides. Review the following specifications to ensure
that your operating or storage environment is suitable for the instrument.

NOTE Install the instrument so that the detachable power cord is readily identifiable

and is easily reached by the operator. The detachable power cord is the
instrument disconnecting device. It disconnects the mains circuits from the
mains supply before other parts of the instrument. The front panel switch is
only a standby switch and is not a LINE switch. Alternatively, an externally
installed switch or circuit breaker (which is readily identifiable and is easily
reached by the operator) may be used as a disconnecting device.

CAUTION If the Infiniium DCA is mounted in a rack or cabinet, do not use the system’s

power switch to disconnect power from the Infiniium DCA. Instead, use the
Infiniium DCA’s front-panel power switch. Using the system power switch may
corrupt the Windows XP registry requiring you to perform a recovery process
to restore normal operation to the Infiniium DCA.

Table 1-2. Environmental Specifications

Use indoor
Temperature

Operating 10 °C to +40 °C (50 °F to + 104 °F)
Non-operating –40 °C to +70 °C (–40 °F to +158 °F)

Altitude

Operating Up to 4,600 meters (15,000 ft)

Line Power 115V 5.7A

230V 3.0A
50/60 Hz

Weight

Mainframe 15.5 kg (34 lb)
Modules 1.2 kg (2.6 lb)

Dimensions (excluding handle)

Height (characteristic)
Width (characteristic)
Depth (characteristic)
Depth with front connectors

and rear feet

(characteristic)

215 mm (8.47 in)

425 mm (16.75 in)

566 mm (22.2 in)

629 mm (24.8 in)

1-7

Installing the 86100C

Step 3. Install the modules

Step 3. Install the modules

Up to two modules can be inserted into the Infiniium DCA. All documentation
(including specifications) for plug-in modules is located in the 86100C’s Help
system. To access the Help system, complete the installation steps, turn on
the 86100C, and click Contents on the Help menu.

1 Slide the module into an available front-panel slot.

You can remove or install a module while the instrument is operating.

2 Finger tighten the two knurled locking screws on the module’s front panel.

Figure 1-2. Installing a Module

1-8

Installing the 86100C

Step 4. Connect the keyboard and mouse

Step 4. Connect the keyboard and mouse

NOTE To complete the installation, you must connect the keyboard to the 86100C.

Since the 86100C has a touch screen, the use of a mouse is optional.

1 Connect the supplied USB keyboard to either of two USB ports located on the

rear panel. Most users find it more convenient to connect the keyboard to the
rear-panel leaving the front-panel USB port available for a USB flash drive.
Rear-panel PS/2 connectors are also provided in case you want to use a PS/2
keyboard or pointing device. Older AT style (DIN 5) keyboards will require an
adapter that is available at many computer stores.

Figure 1-3. Accessory Connections

2 Connect the optional mouse to any available USB port that is located on the

instrument including the two USB ports located on the keyboard.

1-9

Installing the 86100C

Step 5. Connect a printer (Optional)

Step 5. Connect a printer (Optional)

Perform this step if you plan to connect a printer directly to the serial, parallel,
or USB ports that are located on the 86100C rear panel. If you have a parallel
(Centronics) printer, you will need a parallel printer cable, such as an C2950A
(2 m) or C2951A (3 m) cable. If you have a serial printer, you will need a 9-pin
to 25-pin serial printer cable, such as an 34398A cable, plus the 34399A
adapter kit. Some printers may require other cable configurations, but the
86100C has a 9-pin serial connector.

• Attach the required parallel or serial printer cable between your printer and the
86100C’s rear-panel connector.

Figure 1-4. Location of Parallel and Serial Printer Ports

Support for printers with Plug and Play support will automatically be installed
when the instrument is first turned on. For other printers, use the Add
Printer Wizard from the Windows XP desktop. From the Windows Start
menu, click Printers and Faxes, and then click Add a printer.

1-10

Installing the 86100C

Step 6. Connect the power

Step 6. Connect the power

CAUTION Always use the three-prong AC power cord supplied with this instrument.

Failure to ensure adequate earth grounding by not using this cord may cause
product damage.

CAUTION Do not connect ac power until you have verified the line voltage is correct as

described in Table 1-2 on page 1-7. Damage to the equipment could result.

• Connect the line cord as shown in the figure below.

Figure 1-5. Line Cord Connector on 86100C Rear Panel

The 86100C automatically adjusts for line input voltages of 115 VAC and
230 VAC. There is no voltage selection switch. The line cord provided is
matched by Agilent to the country in which the order originates. Refer to

Table 1-3, “Available Line Cords,” on page 1-13 for a list of other available line

power cords.

1-11

Installing the 86100C

Step 6. Connect the power

CAUTION This instrument has autoranging line voltage input. Be sure the supply voltage

is within the specified range.

CAUTION Windows XP registry: If the Infiniium DCA is mounted in a rack or cabinet, do

not use the system power switch to disconnect power from the instrument.
Instead, use the Infiniium DCA front-panel power switch. Using the system
power switch may corrupt the Windows XP registry requiring you to perform
the recovery procedure to restore normal operation to the Infiniium DCA.

Refer to “To recover the 86100C Drive-C” on page 2-25.

1-12

Table 1-3. Available Line Cords

Installing the 86100C

Step 6. Connect the power

Plug Type Cable Part No. Plug Description

250V 8120-1351

8120-1703

125V 8120-1369

Straight *BS1363A

90°

Straight *NZSS198/ASC

90°

8120-0696

250V 8120-1689

8120-1692

8120-2857p

125V 8120-1378

8120-1521

8120-1992

250V 8120-2104

8120-2296

Straight *CEE7-Y11

90°

Straight (Shielded)
Straight *NEMA5-15P

90°

Straight (Medical) UL544
Straight *SEV1011

1959-24507

Type 12 90°

220V 8120-2956

8120-2957

250V 8120-4211

8120-4600

Straight *DHCK107

90°

Straight SABS164

90°

Length
(in/cm)

90/228

90/228

79/200

87/221
79/200

79/200

79/200
90/228

90/228

96/244
79/200

79/200

79/200

79/200

79/200

79/200

Color Country

Gray

Mint Gray

Gray

United Kingdom, Cyprus,
Nigeria, Zimbabwe,
Singapore

Australia, New Zealand

Mint Gray
Mint Gray

Mint Gray

Coco Brown
Jade Gray

Jade Gray

East and West Europe,
Saudi Arabia, So. Africa,
India (unpolarized in many
nations)
United States, Canada,
Mexico, Philippines,
Taiwan

Black
Mint Gray

Switzerland

Mint Gray

Mint Gray

Denmark

Mint Gray

Jade Gray Republic of South Africa

India

100V 8120-4753

8120-4754

* Part number shown for plug is the industry identifier for the plug only. Number shown for

cable is the Agilent Technologies part number for the complete cable including the plug.

Straight MITI

90°

90/230

90/230

Dark Gray Japan

1-13

Installing the 86100C

Step 7. Windows Setup Wizard

Step 7. Windows Setup Wizard

This step requires several minutes to prepare Windows XP using the Windows
XP Setup Wizard. During the following steps, you will be instructed to “click”
with the pointing device. You can use a mouse (if you connected it) or you can
touch the screen with your finger.

CAUTION Before switching on this instrument, make sure the supply voltage is in the

specified range.

CAUTION Avoid touching the screen with a sharp object, as this could result in damage to

the display. Instead, use your finger.

1 Press the ON/OFF switch, , located at the lower left-hand corner of the

front panel.

Figure 1-6. ON/OFF Switch

2 Wait until the Welcome to the Windows XP Setup Wizard appears as shown

in the following figure.

1-14

Figure 1-7. Windows XP Setup Wizard

3 Click Next to display the License Agreement.

Installing the 86100C

Step 7. Windows Setup Wizard

Figure 1-8. Windows XP License Agreement

4 Select I accept this agreement and then click Next.

1-15

Installing the 86100C

Step 7. Windows Setup Wizard

5 Enter your name and the name of your organization or company. Click Next.

Figure 1-9. Personal Information Setup

6 Click Next.

7 Adjust the date, time, and time zone as needed in the displayed screen. Check

automatic clock adjust for daylight saving changes, if it applies to your location.

Figure 1-10. Date, Time, and Time Zone

1-16

Installing the 86100C

Step 7. Windows Setup Wizard

8 Click Next. The setup will take a few moments to complete and to

automatically restart the instrument. In about one or two minutes, you should
see the 86100C screen screen, as shown in the following figure.

Figure 1-11. The 86100C Display

CAUTION To ensure proper operation of the 86100C, read “Avoid changing these

Windows system settings” on page 2-21.

NOTE When you press the ON/OFF switch to turn the instrument off, there is a small

time delay before you’ll see a change on the instrument. This is normal and
does not indicate a problem.

1-17

Installing the 86100C

Step 8. Change removable hard disk (Option 86100C-090)

Step 8. Change removable hard disk (Option 86100C-090)

If your instrument includes Option 86100C-090, you must repeat the Windows
XP Setup Wizard procedure for the second, identical hard disk. The removable
hard disk option, 86100C-090, is designed for 86100C instruments that are
used in a secure environment. For more information, refer to “To use the

removable hard disk option” on page 1-30.

1 Turn off the 86100C.

2 Locate the hard disk lock, which is located at the upper-left corner of the

86100C's rear panel.

3 Insert one of the supplied keys into the hard disk lock, and turn the key counter

clockwise to unlock the hard disk.

NOTE Identical locks and keys are provided for all removable hard disks. The lock

mechanically secures the disk and is not intended for security purposes.

4 Press the button that is located beneath the lock, and pull out the hard disk.

5 Install the alternate hard disk. Make sure that the hard disk is oriented so that

the connector on the hard disk lines up with the connector in the mainframe.

6 Turn the key clockwise to lock the hard disk.

7 Repeat “Step 7. Windows Setup Wizard” on page 1-14 with the new hard disk.

8 Continue with “Step 9. Install a feature license (Optional)” on page 1-19.

1-18

Installing the 86100C

Step 9. Install a feature license (Optional)

Step 9. Install a feature license (Optional)

If you ordered an optional feature, such as Option 200 Enhanced Jitter Analy­sis, with your 86100C, it was probably installed at the factory. If you ordered it,
but it wasn’t installed, you received a Software Entitlement Certificate that
you must use to install the license on your 86100C.

To confirm if your license was installed

1 On the 86100C Utilities menu, click Licenses.

2 Check the installation status of the license in the Licenses dialog box.

License installed

Host ID and
Serial number

Figure 1-12. Licenses Installed Status

3 If the license that you purchased is installed, no further action is required.

Continue with “Step 10. Calibrate the touch screen” on page 1-22. If your
license was not installed, continue with “To install a license” on page 1-20.

1-19

Installing the 86100C

Step 9. Install a feature license (Optional)

To install a license

1 On the 86100C Utilities menu, click Licenses. Write down the HostID and

Serial # identifiers listed on the displayed dialog box. You will need this

information in the next step.

2 Go to the following web site to obtain your license file. You will need to enter

the HostID and Serial # identifiers for your 86100C. The license file will be sent
to you via email.

www.agilent.com/find/softwarelicense

3 After you receive your license file, copy the file to a memory location that is

available to the 86100C. This could be an external USB device (for example,
flash drive or CD drive) or a network drive.

4 On the 86100C Utilities menu, click Licenses to view the Licenses dialog box.

5 In the dialog box, click to highlight the feature that you want to activate. If the

feature is not listed, click the <new> listing.

6 Click Install License for Feature.

7 In the Install New License dialog box, click Browse for License File, find

the file, and then click Install This License File.

Figure 1-13. Install New License Dialog Box

If the license file is not available, some licenses can be manually entered by
clicking Enter 60 Digit Key Code. (This button may be unavailable for some
licenses.) Manually entering the key code fully fulfills the installation require­ments. Open the license file on your PC using a text editor such as Notepad.
Look for the string SIGN= which marks the beginning of the 60-digit key code,

1-20

Installing the 86100C

Step 9. Install a feature license (Optional)

as shown in the following picture. In the Install New License dialog box,
click Enter 60 Digit Key Code and enter your key code. The letters in the key
code are not case sensitive, so you can enter letters in either upper or lower
case.

Figure 1-14. Example of the contents of a license file

.

Figure 1-15. Enter License Key Dialog Box

1-21

Installing the 86100C

Step 10. Calibrate the touch screen

Step 10. Calibrate the touch screen

The touch screen configuration utility aligns and orientates the touch screen
with the display so that when you touch an element on the display screen, the
instrument can detect the task that you want to perform. The display will
always function as a touch screen, even when a mouse and keyboard are con­nected.

1 On the Utilities menu, choose Touch Screen Config.

2 On the displayed dialog box’s Main tab, click the Calibrate button.

Figure 1-16. Touch Screen Calibration

3 Follow the on-screen instructions, while touching the displayed touch targets.

The calibration will time out within 20 seconds, if you do not touch the screen.

4 Each time that you touch the screen, an audible beep is heard. To turn the

audible click sound off, select the Touch Settings tab. Then, repeatedly click
the button shown in Figure 1-17 on page 23 (in the Touch Sound area) until the
button’s label reads “No beep”.

5 Close the dialog box.

1-22

Figure 1-17. Turning the Touch Beep Off

Installing the 86100C

Step 10. Calibrate the touch screen

1-23