Infiniium 54800 Series
Oscilloscope Probes,
Accessories, and Options
Selection Guide Data Sheet
Table of Contents
Probe Compatibility Table ................................................................2
General Purpose Probes Overview ................................................3
116XA Family Passive Voltage...................................................4
117XA Family Low Mass, Passive Voltage...............................7
High-Frequency Voltage Probes Overview ..................................9
1130A/31A/32A/34A InfiniiMax High-Performance
Active Probe System..................................................................10
1168A/69A InfiniiMax II High-Performance
Active Probe System..................................................................13
1155A Active Single-Ended Voltage........................................16
1156A/57A/58A High-Bandwidth, Active Voltage ..............18
1163A Resistive Divider...............................................................4
54006A Resistor Divider Probe ................................................21
Differential Voltage Probes Overview.........................................22
1130A/31A/32A/34A InfiniiMax High-Performance
Active Probe System..................................................................10
1168A/69A InfiniiMax II High-Performance
Active Probe System..................................................................13
1153A Low-Bandwidth Active Differential Voltage..............23
Current Probes Overview...............................................................26
1146A ac/dc Current .................................................................27
1147A High Bandwidth ac/dc Current ...................................29
High-Voltage Passive Probes Overview .....................................31
10076A (100:1)............................................................................32
N2771A (1000:1).........................................................................33
Mixed-Signal Oscilloscope Logic Probe Kit..............................34
E5396A Half-Size Soft Touch Connectorless Logic Probe.......35
Probing Accessories.......................................................................36
Wedge Adapters.........................................................................36
0.5 mm IC Clips, PC Board Mini-Probe Sockets ....................37
EZ-Probe Positioner ...................................................................38
Logic Analyzer/Oscilloscope Time Correlation........................39
VoiceControl .....................................................................................40
Input Devices and Storage Devices.............................................41
E2610A Keyboard, E2609B Rackmount Kit,
1184A Testmobile.......................................................................41
Infiniium Advanced Analysis Options .........................................42
Support, Services, and Assistance..............................................43
To ensure that you have the tools for dependable
oscilloscope measurements, Agilent Technologies
offers a wide range of oscilloscope probes and
accessories. Each is designed for a specific
measurement need because the physical and
electrical quality of the connection can make
the difference between a good measurement
and a bad one.
For ordering information when replacing your probe or probe accessory:
Refer directly to the page number
listed in the table of contents for
your probe model.
To assist you in selecting the proper
probe for your application:
Use our probe compatibility table
below to find the probes that are
recommended for use with your
Infiniium scope.
Or refer to our probe overview
page at the beginning of each
section in the table of contents
explaining what the different
probe types are and the models
available for your Infiniium.
Probe Compatibility Table
Agilent Infiniium Oscilloscope Model
Probe Type Probe Model 54830B/31B/32B/33A/ 54835A/45A/ 54810A/15A/ 54852A/53A/54A/55A
30D/31D/32D/33D 45B/46A/46B 20A/25A and DSO80000 Series
General Purpose Passive 1160A, 10:1 Incompatible Incompatible Recommended Incompatible
Page 4
1161A, 10:1 Compatible Recommended Incompatible Compatible [1]
1162A, 1:1 Recommended Recommended Recommended Compatible [1]
1164A, 10:1 Incompatible Incompatible Recommended Incompatible
1165A, 10:1 Recommended Compatible Incompatible Incompatible
Low Mass Passive 1171A, 10:1 Recommended Recommended Incompatible Compatible [1]
Page 7
Active Single-Ended 1155A, 750 MHz Recommended Compatible Recommended Compatible
Page 10, 16, 18
1156A, 1.5 GHz Recommended Recommended Recommended Compatible
1157A, 2.5 GHz Compatible Recommended Compatible Compatible
1158A, 4 GHz Compatible Recommended Compatible Compatible
Resistive Divider 1163A, 10:1 Recommended Recommended Recommended Incompatible
Page 4, 21
54006A, 10:1 or 20:1 Compatible [2] Recommended [2] Compatible [2] Recommended [2]
Active Differential 1153A, 200 MHz Recommended Recommended Recommended Compatible
Page 10, 13, 23
1130A, 1.5 GHz [6] Recommended [3] Compatible Incompatible Compatible
1131A, 3.5 GHz [6] Recommended [3] Recommended [4] Incompatible Recommended
1132A, 5 GHz [6] Compatible [3] Compatible [4] Incompatible Recommended
1134A, 7 GHz [6] Compatible [3] Compatible [4] Incompatible Recommended
1168A, 10 GHz [6] Compatible [8] Incompatible Incompatible Recommended [8]
1169A, 12 GHz [6] Compatible [8] Incompatible Incompatible Recommended [8]
Current 1146A, 100 kHz Recommended Recommended Recommended Compatible [1]
Page 27, 29
1147A, 50 MHz Recommended Recommended Recommended Incompatible [7]
High Voltage 10076A, 4 kV Recommended Recommended Recommended Compatible [1]
Page 32, 33
N2771A, 15 kV Recommended Recommended Recommended Compatible [1]
Mixed-Signal Oscilloscope 54826-68701 Recommended [5] Incompatible Incompatible Incompatible
Logic Probe Kit
Page 34
Half-Size Soft Touch E5396A Recommended [5] Incompatible Incompatible Incompatible
Connectorless Logic Probe
Page 35
Table 1.1. Agilent probes compatible with Infiniium oscilloscopes.
2
[1] Requires E2697A 1 MΩ input adapter. The E2697A includes one 10073C
general-purpose 500 MHz, 10:1 passive probe.
[2] Requires E2695A SMA-BNC adapter.
[3] Requires 54830 Series system software revision A.03.10 or higher. For A.02.xx or
lower, order N5383A to upgrade system software.
[4] Requires 54845/46 system software revision A.04.50 or higher.
[5] Recommended for 54830D/31D/32D/33D mixed signal oscilloscopes only.
[6] Each 113XA and 1168A/9A probe amplifier supports both single-ended and
differential measurements.
[7] Order N2774A 50 MHz current probe with N2775A power supply that also requires
the E2697A 1 MΩ input adapter.
[8] Requires 54830 Series, 54850 Series, DSO80000 Series system software revision
A.03.90 or higher. For A.02.xx or lower, order N5383A to upgrade system software.
General Purpose Probes Overview
Passive voltage probes are used
for general purpose probing and
are made with passive components only such as wires, connectors, capacitors and resistors
(when attenuation is required).
There are no active components
such as transistors or amplifiers
in the probe, and therefore passive voltage probes do not need
to be powered.
Model Probe Type Applications and Use Page
116XA Family Passive voltage General purpose, Infiniium replacement probes 4
(excluding the 1163A)
117XA Family Passive voltage Fine-pitched ICs, surface mount devices, and dense circuit boards 7
Passive Voltage Probe Advantages Limitations
116XA are rugged, economical, easy to use, 600 MHz maximum bandwidth
have high dynamic range and high input resistance Higher capacitive loading than active probes
117XA feature low mass, low weight, low tip 500 MHz bandwidth
capacitance compared to other passive probes Not as rugged as 116XA for browsing
Figure 2.1. Agilent 116XA standard
Infiniium replacement probe.
Figure 2.2. Agilent 117XA low mass probe
for fine-pitched ICs, SMDs, and dense
circuit boards.
General purpose probes are
available with attenuation ratios
of 1:1, 10:1, and 20:1. The 10:1
passive voltage probe is the most
commonly used probe, and is
supplied as a standard accessory
with all Infiniium oscilloscopes
having bandwidths ≤ 600 MHz.
3
Built for Reliability
These general purpose replacement devices are built and tested
for high reliability. Kevlar
strengthener has been added to
the probe cable for extra pull
strength. Durable probe tips
are replaceable.
The compact design significantly
reduces the problem of probing
densely populated integrated circuit components or the characteristically minute conductors on
printed circuit boards. These
small lightweight probes allow
measurements that were previously quite difficult, while reducing the danger of shorting. For
tight probing areas, the probe
handle can be unscrewed and
pulled back along the cable.
When probing about the circuit in
debug mode, the probes easily
slip inside the included browsers.
The browsers feature a crown
General Purpose Probes
Agilent 116XA Family Passive Voltage
• Standard replacement probes
for Infiniium scopes with
bandwidths ≤ 600 MHz
• Rugged, economical, easy to use
• Compact design, removable probe
handle for tight probing areas
• Agilent 1163A, 500 Ω resistive
divider, 10:1 attenuation
Figure 2.3. Agilent 116XA family general
purpose replacement probes.
point that digs into solder and
avoids the danger of slipping off
the test point and shorting to
adjacent leads. A pogo pin allows
hand movement on the probes
without losing contact with the
device under test.
The 116XA family probes are
compatible with the AutoProbe
interface, which completely configures the Infiniium oscilloscope
for the probe. A snap-on BNC
connector simplifies attaching
the probe to the scope. Leads are
available for connecting to a
wide variety of test points. See
“Ordering Information” for a
complete list.
Agilent 1163A Resistive Divider
Agilent 1163A features low capacitive loading and wide bandwidth,
resulting in very accurate timing
measurements. Resistive divider
probes are useful for probing lowvoltage signals such as ECL circuits, 50 Ω transmission lines,
and GaAs circuits.
Figure 2.4. No-slip
browser crown point.
4
Specifications
System
Model Bandwidth Division Scope Compensation
Number Type of Probe (scope +probe) Ratio Input R Input C Input R Range Length
1160A High Impedance, 500 MHz 10:1 10 MΩ 9 pF 1 MΩ 6 - 9 pF 1.5 m
Passive
1161A High Impedance, 500 MHz 10:1 10 MΩ 10 pF 1 MΩ 12 - 14 pF 1.5 m
Passive
1162A High Impedance, 25 MHz 1:1 1 MΩ 50 pF + scope 1 MΩ n/a 1.5 m
Passive capacitance
1163A 500 Ω Resistive 1.5 GHz with 10:1 500 Ω 1.5 pF 50 Ω n/a 1.5 m
Divider scope model
54845A/B
1164A High Impedance, 500 MHz 10:1 10 MΩ 10.5 pF 1 MΩ 6 - 9 pF 2.0 m
Passive
1165A High Impedance, 600 MHz 10:1 10 MΩ 10 pF 1 MΩ 12 - 14 pF 1.5 m
Passive typical with
54830B/31B/32B/33A
54830D/31D/32D/33D
Operating Characteristics
Approximate propagation delay 6.7 ns for 1160A/61A/62A/63A/65A probes
8.8 ns for 1164A probe
Maximum input voltage 300 V (dc + peak ac), CAT II
10 V (dc + peak ac), CAT I for 1163A only
Safety Meets IEC1010-2-31
Pulling strength (BNC to barrel) ≤ 12 lb static pull
Net weight 2.6 oz
Environmental Characteristics
Temperature (operating) 0° C to +55° C
Humidity (operating) Up to 95% relative humidity at 40° C
Altitude (operating) Up to 4,600 meters (15,000 ft.)
Shock 50 g (400 g tip only)
General Purpose Probes
Agilent 116XA Family Passive Voltage
5
Ordering Information
Probes and Accessories
Part # Description Quantity
1160A 10:1, 10 MΩ, 1.5 m, miniature passive probe 1
1161A 10:1, 10 MΩ, 1.5 m, miniature passive probe 1
1162A 1:1, 1.5 m, miniature passive probe 1
1163A 10:1, 500 Ω, low C, 1.5 m, miniature passive probe 1
1164A 10:1, 10 MΩ, 2 m, miniature passive probe 1
1165A 10:1, 10 MΩ, 1.5 m, miniature passive probe 1
5063-2143 Probe tip to BNC (m) 1
IC clips: See “Probing Accessories”
Horizontal and vertical mini-probe sockets: See “Probing Accessories”
Wedge Probe Adapters: See “Probing Accessories”
Replacement Parts
Part # Description Quantity
5063-2135 General purpose retractable hook tip 2
5063-2140 Alligator ground lead 2
5063-2120 Socketed ground lead 1
5063-2115 Browser 1
5063-2147 Dual lead adapter 1 0
5063-2149 SMD clips 5
01160-68701 Accessory kit (includes four spring grounds, 1
four browser pogo pins, four barrel insulators,
one screwdriver)
5063-2136 1160A probe tip, red 5
5063-2137 1161A probe tip, brown 5
5063-2138 1162A probe tip, black 5
5063-2139 1163A probe tip, grey 5
5063-2151 1164A probe tip, orange 5
5063-2137 1165A probe tip, brown 5
One probe
Two
probe tips
Two barrel insulators
One
browser
One
generalpurpose
retractable
hook tip
One
dual-lead
adapter
Two SMD clips
Four spring
grounds
One alligator ground lead
One socketed ground lead
One screwdriver
One
browser
pogo pin
(spare)
Probe Parts Supplied
Includes user’s guide and
three-year warranty.
General Purpose Probes
Agilent 116XA Family Passive Voltage
6
Suited for Today’s ICs
An exceptionally small and light
probe tip (<1 gram) and an ultra
thin cable make the 117XA family
ideal for connecting to and probing fine-pitch ICs, surface mount
devices, and dense circuit boards.
The probe fits directly onto standard board headers and IC clips.
A range of accessories are available for you to optimize interfacing with surface mount devices.
Wedge Probe Adapters make convenient and reliable connections
to TQFP/PQFP package leads. See
“Ordering Information” for a complete list of accessories.
General Purpose Probes
Agilent 117XA Family Low Mass, Passive Voltage
• Easy connection to fine-pitch ICs,
SMDs, and dense circuit boards
• Light weight (< 1 gram), low
mass probe tip
• 10:1 attenuation, capacitance
< 10 pF (1171A)
Figure 2.5. Agilent 117XA family probes for
fine-pitch ICs, surface mount devices, and
dense circuit boards.
When probing about the circuit in
debug mode, the probe easily slips
inside the included browsers. The
browsers feature a crown point
that digs into solder and avoids
the danger of slipping off the test
point and shorting to adjacent
leads. A pogo pin allows hand
movement on the probes without
losing contact with the device
under test.
The 117XA probes are compatible
with the AutoProbe interface,
which completely configures the
Infiniium oscilloscope for the
probe. A snap-on BNC connector
simplifies attaching the probe to
the scope.
Specifications
System
Model Bandwidth Division Scope Compensation
Number Type of Probe (scope + probe) Ratio Input R Input C Input R Range Length
1171A High Impedance, 500 MHz 10:1 10 MΩ 10 pF 1 MΩ 12 - 14 pF 1.4 m
Passive
7
Specifications
Operating Characteristics
Approximate propagation delay 1171A: 6.5 ns
Maximum input voltage 40 V (dc + peak ac), CAT I
Safety Meets IEC1010-2-31
Pulling strength (BNC to probe tip) ≤ 12 lb static pull
Net weight 2.6 oz
Probe tip weight < 1 gram
Environmental Characteristics
Temperature (operating) 0° C to +55° C
Humidity (operating) Up to 95% relative humidity at 40° C
Altitude (operating) Up to 4,600 meters (15,000 ft.)
Shock 50 g (400 g tip only)
Ordering Information
Probes and Accessories
Part # Description Quantity
1171A 10:1, 10 MΩ, 1.4 m, low mass passive probe 1
IC clips: See “Probing Accessories”
Wedge Probe Adapters: See “Probing Accessories”
Replacement Parts
Part # Description Quantity
5063-2122 Browser 1
Probe Parts Supplied
Includes two IC clips, user’s guide, and
one-year warranty.
Two pogo pins
One alligator
ground lead
One socketed
ground lead
Two probing pins
One ground
extender
One probe
One
browser
One
screwdriver
One walking
stick ground
General Purpose Probes
Agilent 117XA Family Low Mass, Passive Voltage
8
High-Frequency Voltage Probes Overview
Active voltage probes contain an
active component, usually a fieldeffect transistor (FET), and therefore need to be powered. A FET
input has the advantage of providing a very low input capacitance, typically from less than
1 pF to a few pF. This low capacitance results in a high input
impedance on frequencies up to
7 GHz. With such low loading,
active probes can be used on
high-impedance circuits that
would be seriously loaded by
passive probes.
New InfiniiMax probe family.
The innovative InfiniiMax probe
system provides either differentialor single-ended probing solutions
for the most demanding connection requirements, without sacrificing performance.
Figure 3.1. Agilent 1130A/31A/32A/34A
InfiniiMax high-performance active probe.
Figure 3.2. Agilent 1156A/57A/58A
active probes for signals up to 4 GHz.
Model Probe Type Applications and Use Page
1130A/31A/32A/34A Active Diff/SE Measure both differential and single-ended signals up to 7 GHz 10
1155A Active Single-Ended Measure fast transitions on low-voltage signals, 2 channels 16
1156A/57A/58A Active Single-Ended Measure fast transitions on low-voltage signals up to 4 GHz 18
1163A Resistive divider Measure fast transitions on a wide range of signal voltages 4
54006A Resistive divider Low-cost alternative for high-frequency probing 21
High-Frequency Probe Advantages Limitations
Timing and voltage measurements more accurate at Active probes are more expensive than general purpose passive probes
high bandwidths
Resistive divider probes cost less than active probes Relatively heavy resistive loading with resistive divider probes
Active probes are least intrusive to circuit under test, Active probes have lower dynamic range, lower maximum voltage and
high input resistance are less rugged compared to passive probes
Resistive divider probes are
passive probes. They feature low
capacitive loading and accurate
timing measurements with highbandwidth signals at a much
lower cost than active probes.
9
High-Frequency Active Differential/Single-Ended Probe System
Agilent 1130A/31A/32A/34A InfiniiMax High-Performance Active Probe System
• The Agilent InfiniiMax 1130A
series probe system supports
a wide variety of real-world
applications with an extensive line up of probe heads and
accessories. The accessories
can meet the most demanding
mechanical access requirements.
Small probe heads can be placed
between densely packed PC
boards. Solder-in sockets are
available for signals that need
frequent measurement. A differential SMA probe head is
available to connect to fixtures
that have SMA connections. A
smart ergonomic design allows
users to set the spacing between
the probe pins (variable span).
When not concerned with minimum probe size, designers can
use a browsing sleeve to make
holding the probe more comfortable. Both probe tips of the
differential probe can “flex” to
support various probing angles
and target system characteristics
(z-axis compliance). Innovative
damped-wire accessories compensate for the inductance and
capacitance associated with
the leads, and prevent distortion of the measured signal.
• InfiniiMax 7 GHz, 5 GHz, 3.5 GHz,
and 1.5 GHz probing system
• Each InfiniiMax probe amplifier
supports both differential and
single-ended measurements for
a more cost-effective solution
• Unrivaled InfiniiMax probing
accessories support browsing,
solder-in, and socket use models
at the maximum performance
available
The Agilent InfiniiMax 1134A,
1132A, 1131A and 1130A probe
systems provide 7 GHz, 5 GHz,
3.5 GHz and 1.5 GHz of band-
width respectively, and offer the
following benefits:
• The new probes have a flat
frequency response over the
entire bandwidth specification,
eliminating the distortion and
loading that affect probes with
in-band resonance. The probing
system enables engineers to
utilize their oscilloscope’s entire
bandwidth without being limited
to measuring only 50 Ω transmission lines or using passive
resistive divider probes that
produce voltage measurement
error and circuit loading.
Designers can achieve system
measurement bandwidths of
4.5 to 6 GHz even when manually “browsing” with the probe.
Solder-in probe heads and
solder-in sockets provide even
higher bandwidths.
Figure 3.3. InfiniiMax offers you the highest performance available
for measuring differential and single-ended signals.
• The groundbreaking design of
Agilent InfiniiMax 1130A probe
system also enables users to
make either single-ended or
differential measurements
from a single probe amplifier,
depending on their choice of
probe head and accessory. This
can result in significant savings
in cost and time. The common
mode rejection of the differential probe head reduces a measurement’s noise floor. Overall,
the Agilent 1130 series probing
system delivers unmatched
performance, accuracy
and connectivity.
InfiniiMax: The World’s Best
High-Speed Oscilloscope
Probing System
EDN Magazine has awarded
Agilent’s InfiniiMax active probe
system the 2002 Innovation of
the Year Award.
10
High-Frequency Active Differential/Single-Ended Probe System
Agilent 1130A/31A/32A/34A InfiniiMax High-Performance Active Probe System
Specifications
Operating Characteristics
Probe bandwidth* 1134A: > 7 GHz
1132A: > 5 GHz
1131A: > 3.5 GHz
1130A: > 1.5 GHz
Rise and fall time (10% to 90%) 1134A: 60 psec
1132A: 86 psec
1131A: 100 psec
1130A: 233 psec
System bandwidth (–3 dB) 1134A with 54855A: 6 GHz
1132A with 54854A: 4 GHz
1131A with 54853A: 2.5 GHz
1131A with 54852A: 2 GHz
1130A with 54832B/D, 33A/D: 1 GHz
Input capacitance** Cm = 0.1 pF Cm is between tips.
Cg = 0.34 pF Cg is to ground for each tip.
Cdiff = 0.27pF Differential mode capacitance = Cm + Cg/2
Cse = 0.44 pF Singe-ended mode capacitance = Cm + Cg
Input resistance* Differential mode resistance = 50 kΩ ±1%
Single-ended mode resistance = 25 kΩ ±1%
Input dynamic range ±2.5 V
Input common mode range ±6.75 V dc to 100 Hz; ±1.25 V >100 Hz
Maximum signal slew rate 18 V/ns when probing a single-ended signal
30 V/ns when probing a differential signal
DC attenuation 10:1 ± 3% before calibration on oscilloscope
10:1 ± 1% after calibration on oscilloscope
Zero offset error referred < 30 mV before calibration on oscilloscope
to input < 5 mV after calibration on oscilloscope
Offset range* ± 12.0 V when probing single-ended
Offset accuracy < 3 % setting before calibration on oscilloscope
< 1 % setting after calibration on oscilloscope
Noise referred to input 3.0 mVrms
Propagation delay ~6 nsec (This delay can be deskewed relative to
other signals.)
Maximum input voltage* 30 Vpeak, CAT I
ESD tolerance > 8 kV from 100 pF, 300 Ω HBM
* Denotes warranted specifications, all others are typical.
** Measured using the probe amplifier and solder-in differential probe head with full bandwidth resistors.
Figure 3.4. Swept frequency response.
Figure 3.5. Common mode rejection
vs. frequency.
Example of characterized
performance plots: differential
solder-in probe head
11
6
3
0
dB
-3
-6
-9
-12
8
10
0
-10
-20
dB
-30
-40
-50
-60
8
10
9
10
Frequency (Hz)
9
10
Frequency (Hz)
10
10
10
10
High-Frequency Active Differential/Single-Ended Probe System
Agilent 1130A/31A/32A/34A InfiniiMax High-Performance Active Probe System
Ordering Information
Probe Amplifier Model
Part # Description Quantity
1134A 7 GHz InfiniiMax Probe Amplifier (order one or more probe heads or connectivity kits per amplifier). 1
1132A 5 GHz InfiniiMax Probe Amplifier (order one or more probe heads or connectivity kits per amplifier). 1
1131A 3.5 GHz InfiniiMax Probe Amplifier (order one or more probe heads or connectivity kits per amplifier). 1
1130A* 1.5 GHz InfiniiMax Probe Amplifier (order one or more probe heads or connectivity kits per amplifier). 1
* Note: Requires 54830 Series system software revision A.03.10 or higher. For A.02.xx or lower, order N5383A to upgrade system software.
Connectivity Kits Model
Part # Description Quantity
E2669A InfiniiMax connectivity kit for differential/single-ended measurements. Includes one 1
differential browser, four solder-in differential probe heads and two socketed differential probe
heads. Includes all necessary accessories.
E2668A InfiniiMax connectivity kit for single-ended measurements. Includes one single-ended browser, 1
one solder-in probe heads and one socketed probe heads. Includes all necessary accessories.
Individual Probe Heads
Part # Description Quantity
E2675A InfiniiMax differential browser probe head and accessories. Includes 20 replaceable tips and 1
ergonomic handle. Order E2658A for replacement accessories.
E2676A InfiniiMax single-ended browser probe head and accessories. Includes 2 ground collar 1
assemblies, 10 replaceable tips, a ground lead socket and ergonomic handle.
Order E2663A for replacement accessories.
E2677A InfiniiMax differential solder-in probe head and accessories. Includes 20 full bandwidth and 1
10 medium bandwidth damping resistors. Order E2670A for replacement accessories.
E2678A InfiniiMax single-ended/differential socketed probe head and accessories. Includes 48 full 1
bandwidth damping resistors, 6 damped wire accessories, 4 square pin sockets and socket
heatshrink. Order E2671A for replacement accessories.
E2679A InfiniiMax single-ended solder-in probe head and accessories. Includes 16 full bandwidth and 1
8 medium bandwidth damping resistors and 24 zero ohm ground resistors. Order E2672A for
replacement accessories.
E2695A Differential SMA probe head. Includes semi-rigid coax to change span between SMA connectors. 1
Adapters
Part # Description Quantity
N1022A Adapts 113X/115X active probes to 86100 Infiniium DCA. 1
E2696A General purpose probing solution for use with instruments such as spectrum analyzers and 1
network analyzers. Includes N1022A probe adapter, N1022-60014 connection adapter, and
01143-61602 probe power extension cable. Items that must be purchased separately for a
complete probing solution are an InfiniiMax probe amplifier and desired probe heads, and
1143A probe power supply.
12
13
Two new high-bandwidth InfiniiMax II
Series probe amplifiers have been added to
the InfiniiMax product line. InfiniiMax I
probe amplifiers and probe heads can also
be used with DSO 80000 Series scopes for
lower performance applications.
High-Frequency Active Differential/Single-Ended Probe System
Agilent 1168A/69A InfiniiMax II High-Performance Active Probe System
12 GHz Hi-BW
differential
SMA probe
head provides
maximum
bandwidth for
SMA fixtured
differential
pairs.
12 GHz Hi-BW solder-in differential probe
head provides maximum bandwidth and
minimizes capacitive loading to ≤ 210 fF.
Variable spacing from 0.2 to 3.3 mm (8 to
130 mills).
12 GHz Hi-BW differential browser provides
maximum bandwidth for hand-held or probe
holder use. Variable spacing from 0.2 to
3.3 mm (8 to 130 mills).
InfiniiMax II: The World’s Best High-Speed
Probing System Just Got Better
InfiniiMax offers you the highest performance
available for measuring differential and
single-ended signals, with flexible connectivity
solutions for today’s high-density ICs and
circuit boards.
InfiniiMax probes have fully characterized
performance for all of their various probe heads.
This includes:
• Swept frequency response plot
• Common mode rejection vs. frequency plot
• Impedance vs. frequency plot
• Time-domain probe loading plot
• Time-domain probe tracking plot
One-year standard warranty on active probes and
a variety of Agilent support options to choose from.
Controlled impedance transmission lines in every
probe head deliver full performance versus the
performance limitations produced by traditional
wire accessories.
Probe interface software allows you to save the
calibration information for up to 10 different probe
heads per channel and will automatically retrieve
calibration data for a probe amplifier as it is
attached to the scope.
High-input impedance active probes minimize
loading, support differential measurements and DC
offset, and can compensate for cable loss.
Probe calibration software delivers the most
accurate probe measurements, linear phase
response and allows various probe combinations
to be deskewed to the same reference time.
InfiniiMax II probe heads
Loading...