Keysight N9917A, N9914A, N9918A, N9950A, N9951A Configuration Manual

...

Download

Keysight Technologies

FieldFox Handheld Analyzers

4/6.5/9/14/18/26.5/32/44/50 GHz

Configuration Guide

02 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

Table of Contents

The FieldFox Handheld Analyzer Family 03

FieldFox RF and Microwave (Combination) Analyzers 04

FieldFox RF and Microwave (Combination) Analyzer FAQs 05

FAQs – Applicable To All FieldFox RF and Microwave Analyzers 08

FieldFox Microwave Vector Network Analyzers 10

FieldFox Microwave Vector Network Analyzer FAQs 11

FieldFox Microwave Spectrum Analyzers 12

FieldFox Spectrum Analyzer FAQs 13

Documentation 13

Upgrades 14

Calibration Kits 16

Accessories 18

03 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

The FieldFox Handheld Analyzer Family

This configuration guide describes configurations, options and accessories for the FieldFox family of portable analyzers. This guide should be used in conjunction with the technical overview and data sheet for a complete description of the analyzers. The table below shows a comparison of the functions available in the FieldFox family of analyzers.

The following accessories are included with every FieldFox: AC/DC adapter, battery, soft carrying case, LAN cable and Quick Reference Guide.

Note: Combination analyzer (combo) = Cable and antenna tester (CAT) + Vector network analyzer (VNA) + Spectrum analyzer (SA)

FieldFox family and options

RF and microwave (combination) analyzer

Option Description N991x A

N995xA

Microwave vector network analyzer (VNA)

Microwave spectrum analyzer (SA)

N992xA N993xA

N996xA

CAT/vector network analysis

010 VNA time domain √ √ — 112 QuickCal √ on N991xA

- on N995xA

210 211

VNA transmission/reflection VNA full 2-port S-parameters √

√ Base model

√ —

√

— —

212 1-port mixed-mode S-parameters √ √ —

215 TDR cable measurements √ √ — 305 Cable and antenna analyzer Base model √ Note 1

308 Vector voltmeter √ √ — 320 Reflection meas. (RL, VSWR and scalar meas.) Note 2 Note 2 √

Spectrum analysis

209 Extended range transmission analysis (ERTA) √ — √ 220 Tracking generator Note 3 — √ 233 Spectrum analyzer √ — Base model 235 Pre-amplifier √ — √ 236 Interference analyzer and spectrogram √ — √ 238 Spectrum analyzer time gating √ — √ 312 Channel scanner √ — √

350 Real-time spectrum analyzer (RTSA) √ - on N9912A — √ 351 I/Q Analyzer (IQA) √ - on N9912A — √ 355 Analog demodulation √ — √

Power measurements

208 USB power sensor meas. versus frequency √ √ √ 302 USB power sensor support √ √ √ 310 Built-in power meter √ √ √ 330 Pulse meas. with USB peak power sensor √ √ √

System features

030 Remote control capability √ √ √ 307 GPS receiver √ √ √

309 DC bias variable-voltage source √ √ √

Windows based software

896 01B 89600 VSA Software √ - on N9912A — √

Notes: Base model means that the functionality listed is the primary function of that instrument. For example, on the N991xA or N995xA combo analyzers, cable and antenna analysis is the standard function included with ever y N991xA or N995xA.

1. Option 305 is not available on the N993xA or N996xA. However, a subset of cable and antenna analyzer measurements, return loss and VSWR, is available as Option 320.

2. Option 320 is not applicable to N991xA, N995x A, or N992xA. The reflection measurements of return loss and VSWR are included with every N991xA, N995xA, and N992x A. So there is no need for an Option 320 on these analyzers.

3. On the N991xA or N995xA analyzers, order Options 233 and 210 to obtain a tracking generator with the spectrum analyzer. There is no Option 220 on the N991xA or N995xA analyzers. To obtain tracking generator capabilit y, you need Options 233 and 210. Option 233 provides the spectrum analyzer capability and Option 210 the “tracking” capability.

04 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

FieldFox RF and Microwave (Combination) Analyzers

FeldFox RF and microwave (combination) analyzer models

St ep 1. Select the model that provides the desired frequency range.

Model Description CAT and VNA frequency SA frequency

N9913A 4 GHz FieldFox RF analyzer 30 kHz to 4 GHz 100 kHz to 4 GHz Type-N (f) N9914 A 6.5 GHz FieldFox RF analyzer 30 kHz to 6.5 GHz 100 kHz to 6.5 GHz Type-N (f) N9 915A 9 GHz FieldFox microwave analyzer 30 kHz to 9 GHz 100 kHz to 9 GHz Type-N (f) N9916A 14 GHz FieldFox microwave analyzer 30 kHz to 14 GHz 100 kHz to 14 GHz Type-N (f) N9 917A 18 GHz FieldFox microwave analyzer 30 kHz to 18 GHz 100 kHz to 18 GHz Type-N (f) N9918A 26.5 GHz FieldFox microwave analyzer 30 kHz to 26.5 GHz 100 kHz to 26.5 GHz 3.5 mm (m) N9950A 32 GHz FieldFox microwave analyzer 300 kHz to 32 GHz 9 kHz to 32 GHz NMD 2.4 mm (m) N9951A 44 GHz FieldFox microwave analyzer 300 kHz to 44 GHz 9 kHz to 44 GHz NMD 2.4 mm (m) N9952A 50 GHz FieldFox microwave analyzer 300 kHz to 50 GHz 9 kHz to 50 GHz NMD 2.4 mm (m)

Step 2. Select optional measurement capabilities. Any of these options can easily be added as a software upgrade in the future. Exception: Option 112 is only applicable to N991xA models. It is not applicable to N995xA models.

Test port connectors

FieldFox RF and microwave (combination) analyzer options

Option Description Prerequisite options/notes

CAT/vector network analysis

010 VNA time domain Requires 210, recommend 211 112 QuickCal Not available for N995xA models. See page 5, FAQ #9 210 VNA transmission/reflection Recommend ordering a cal kit 211 VNA full 2-port S-parameters Requires 210, recommend ordering a cal kit 212 1-port mixed-mode S-parameters Requires 210 and 211 215 TDR cable measurements 308 Vector voltmeter 210 and 211 required to obtain full VVM functionality. See page 5, FAQ #8

Spectrum analysis

209 Extended range transmission analysis (ERTA) Requires 233 and 210. Recommend 307. Requires two FieldFoxes. See page 6, FAQ # 10.

233 Spectrum analyzer 235 Pre-amplifier Requires 233 236 Interference analyzer and spectrogram Requires 233 238 Spectrum analyzer time gating Requires 233

312 Channel scanner Requires 233

350 Real-time spectrum analyzer (RTSA) 351 I/Q Analyzer (IQA)

355 Analog demodulation Requires 233

Power measurements

208 USB power sensor meas. versus frequency Requires 302 302 USB power sensor support Need to order USB power sensor 310 Built-in power meter No power sensor required. See page 8, FAQ #1 330 Pulse meas. with USB peak power sensor Need to order USB peak power sensor. See page 9, FAQs #7 and #8

System features

030 Remote control capability Requires an iOS device 307 GPS receiver Need to order GPS antenna, N9910X-825. See page 9, FAQ #3 309 DC bias variable-voltage source -

Windows based software

896 01B 89600 VSA Software

Requires 233, Recommend 235.

Requires 233

1. Usable to 5 kHz

2. List of compatible sensors available from www.keysight.com/find/fieldfoxsupport

3. Requires CPU2 fast processor. See page 6, FAQ #13

05 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

FieldFox RF and Microwave (Combination) Analyzer FAQs

Question Answer

1. What is included with a base

N991xA /N995xA analyzer?

2. What is included with N991xA / N995xA Option 233?

3. What is included with N991xA / N995xA Option 236?

4. What is included with N991xA / N995xA Option 210?

5. What is included with N991xA / N995xA Option 211?

6. Can I measure group delay on N991xA /N995xA analyzers?

7. What is included with N991xA/ N995xA Option 010?

8. What is included with N991xA/ N995xA Option 308?

9. What is included with N991xA Option 112?

– The base model includes the cable and antenna analyzer – Measurements: DTF (dB, linear, VSWR), return loss and DTF, return loss (dB), and 1-port cable loss

– Calibrations: CalReady, OSL, and response cal Note: 2-port insertion loss is NOT included with the base model, if 2-port insertion loss is needed, order Option 210 Note: There is no phase information with the base analyzer, to obtain S11 or S21 phase, order Option 210

– Basic spectrum analysis, four traces, different detector types, radio standard selection, limit lines

– Channel power, occupied bandwidth, adjacent channel power

– AM/FM tune and listen, field strength measurements, antenna factors, frequency counter marker

– Tracking generator (TG)/Independent source:

– TG CW mode (source CW frequency can be set independent of SA frequency) - included – TG CW coupled mode (source CW frequency is autocoupled to SA’s center frequency) - included

– TG tracking mode (traditional TG operation, swept SA coupled to swept source) - (requires Option 210) – Interference analyzer and spectrogram – Trace playback and recording – Option 210 adds a VNA with transmission/reflection (T/R) capability – Measurements: S21, S11, magnitude and phase – Additionally, in the CAT mode, you can measure 2-port insertion loss – Calibrations: CalReady, OSL, response, and enhanced response cal – If you need all four S-parameters, order Options 210 and 211 – If you need 2-port cal, order Options 210 and 211 – Adds tracking mode to the tracking generator/independent source included with Option 233, spectrum

analyzer – Option 211 adds full 2-port S-parameter capability to the VNA mode – Measurements: All four S-parameters (S11, S21, S22, S12), magnitude and phase – Calibrations: CalReady, OSL, response, enhanced response, and full 2-port cal

If you have phase measurement capability, then you can measure group delay. Option 210 is required for any phase measurement capability. So if you do not have Option 210, you cannot measure group delay.

– S11/S21 in time domain, if Option 210 is ordered. To get time domain data for all four S-parameters and full

2-port cal, order Option 211. – View both time and frequency domain data at the same time – Low-pass, impulse, and band-pass modes – Minimum, medium, and maximum window – Gating – With Option 308: 1-port cable trimming – With Options 308 and 210: 1-port cable trimming, 2-port transmission – With Options 308, 210, and 211: 1-port cable trimming, 2-port transmission, A /B and B/A

Note: A/B and B/A measurements require an external source

– Option 112 (QuickCal), is not available for N995xA analyzers. It is available for N991xA analyzers. – QuickCal is included with Option 112.

– 1-port QuickCal with a base analyzer. – 1-port and enhanced response QuickCal with a T/R analyzer (one that has Option 210). – 1-port, enhanced response, and 2-port QuickCal with a full 2-port analyzer (one that has Option 211).

– QuickCal is most accurate for DUTs with 7/16 and Type-N connectors and measurement uncertainties are

provided for frequencies ≤ 18 GHz. Reduced accuracy for DUTs with 3.5 mm (m), SMA (m), or other male

coaxial connectors; performance is unspecified. QuickCal is not recommended for DUTs with 3.5 mm (f), SMA

(f), or other similar female connectors. QuickCal is not applicable to waveguide.

06 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

FieldFox RF and Microwave (Combination) Analyzer FAQs (continued)

Question Answer

10. What are the requirements for

Option 209?

Extended Range Transmission Analysis (ERTA) or Option 209 is a scalar measurement system based on the use of two FieldFoxes. One FieldFox acts as the source and reference receiver, while the second FieldFox acts as the

measurement receiver. When different frequency models are used in an ERTA pair, the ERTA system frequency

range is limited to the lowest of the pair.

Required hardware

A. Two FieldFoxes. FieldFoxes can be any of these models:

– FieldFox microwave combination analyzers: N9913A, N9914A, N9915A, N9916A, N9917A, N9918A, N9950A,

N9951A, N9952A

– FieldFox microwave spectrum analyzers: N9935A, N9936A, N9937A, N9938A, N9960A, N9961A, N9962A – ERTA cannot use N9912A, N9923A, N9925A, N9926A, N9927A or N9928A

The two FieldFoxes used in ERTA do not have to be the same model.

ERTA requires the following options on Combo FieldFoxes. (N9913A, N9914A, N9915A, N9916A, N9917A, N9918A, N9950A, N9951A, N9952A)

– Option 210, VNA transmission/reflection – Option 233, spectrum analyzer

ERTA requires the following options on SA FieldFoxes. (N9935A, N9936A, N9937A, N9938A, N9960A, N9961A, N9962A)

– Option 220, tracking generator

11. What is included with

Option 355?

12. What is included with

Option 350?

13. How do I determine if my

FieldFox has CPU2 fast processor?

Both FieldFoxes (the one used as the source, and the other used as the receiver) must have the options listed above. The ERTA option (209) cannot be installed unless 210 and 233 are present on a combo analyzer, or 220 is

present on an SA analyzer.

With either the Combo or SA FieldFoxes, the following options are highly recommended:

– Option 235, preamplifier – this option increases the measurement dynamic range by increasing the received

signal power.

– Option 307, GPS receiver – this option increases the dynamic range by increasing the frequency accuracy

and permitting the use of a narrower RBW.

B. Power splitter, two-resistor model, Keysight 11667A, 11667B, or 11667C. Other power splitters can be used but the

specifications listed are based on the match and tracking performance of 11667A, 11667B, or 11667C. Three-resist-

er power splitters are not recommended.

C. N9910X-712, Trigger/Reference-in cable, SMA (m) to BNC(f), 1 m, quantity two

D. N9910X-713, Trigger/Reference-out cable, SMB (m) to BNC (m), 1 m, quantity two

E. LAN connection – For ERTA, the two FieldFoxes communicate via a LAN connection. For a direct connection, a

cross-over LAN cable is required. Alternately, both analyzers can be on a local area network.

Recommended accessory

F. N9910X-825, GPS Antenna

FieldFox analog demodulation has two parts: (1) Tune and listen, and (2) AM/FM metrics. Tune and listen is available with the purchase of the spectrum analyzer option 233. AM/FM metrics becomes available when Option 355 is purchased. AM/FM metrics provides the user with RF spectrum view, demodulated baseband signal waveform,

carrier power, frequency deviation, SINAD and more.

Real-time spectrum analyzer (RTSA) or Option 350 provides real-time measurements on a FieldFox. The FieldFox must be equipped with spectrum analysis capability. The preamplifier option is recommended, as elusive signals often have low power levels. The maximum real-time bandwidth for option 350 is 10 MHz. RTSA includes trace recording and playback capabilities. It does not include a frequency-mask trigger (FMT).

All N995xA and N996xA analyzers include CPU2. On other FieldFox models, if the serial number starts with MY5607/SG5607/US5607, then it has CPU2. If the serial number prefix is dif ferent, then the analyzer firmware needs to be checked to see if the instrument has been upgraded with N9910HU-100/200/300/400 to have CPU2.

07 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

FieldFox RF and Microwave (Combination) Analyzer FAQs (continued)

Question Answer

14. Is Spectrum Analyzer Trace

Recording and Playback

standard or an option?

ERTA System Typical Configuration

Item Description/Options Quantity

FieldFox Combo analyzer: required Option 210, 233. Recommended: 235, 307

Power splitter 11667A (Type-N) or 11667B (3.5 mm) or 11667C (2.4 mm) 1 Type-N(m) to Type-N(m) adapter N9910X-850 (for use with 11667A or Type-N systems) 1

Trigger cables

RF test cable Connecting FieldFox source port 1 to power splitter input 1 RF test cable or adapter Connecting power splitter output arm to FieldFox port 2 1 RF jumper cable or adapter Power splitter output arm to DUT input 1 RF jumper cable or adapter DUT output to FieldFox receiver port 2 1 LAN cable LAN cable to connect FieldFoxes directly, or the analyzers must be on the LAN 1 N9910X-825 GPS antenna, recommended. Necessary if Option 307 is ordered. 2

1. The trigger cables and L AN cables must be at least as long as the separation distance between the two ends of the DUT.

– Spectrum Analyzer mode (Option 233) does not include Trace Recording and Playback by default. To obtain

this capability in SA mode, Option 236 Interference Analyzer and Spectrogram needs to be purchased.

– RTSA mode (Option 350) does include Trace Recording and Playback by default in RTSA mode. – Purchasing RTSA mode (Option 350) does not enable Trace Recording and Playback in SA mode (Option 233).

SA mode

SA & Interference Analyzer

Trace record/playback features

Options 233 and 236

Record and playback spectrum traces Yes Yes

Save trace data with GPS time stamp over time Yes Yes

Record and playback spectrogram data Yes No

Frequency mask trigger Yes No

* RTSA trace recordings can be recalled and played back in SA mode Spectrogram. This has the added benefit that the

measurements are shown ‘slower’, making it easier for the human eye to decipher the signal content.

SA analyzer: required: Option 220, recommended: 235, 307

N9910X-712, SMA(m) to BNC(f) N9910X-713, SMB(m) to BNC(m)

2 of each Total of 4 cables

RTSA mode

RTSA

Option 350

ERTA system diagram

08 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

FAQs – Applicable To All FieldFox RF and Microwave Analyzers

Question Answer

1. What USB power sensors work with

Option 302?

2. What is the difference between USB power sensor (Option 302) and built-in power meter

(Option 310)?

All Keysight U2000x Series USB power sensors are supported with FieldFox. Visit: www.keysight.com/find/fieldfoxsupport for an up-to-date listing.

Option 302 USB power sensor

Description Option 302 allows users to connect a

USB power sensor to FieldFox’s USB

port and make broadband power measurements.

External hardware USB power sensor required None. Uses internal receiver.

Power measurement Broadband diode detector, measures

all frequencies

Frequency range Depends on USB sensor Frequency range of the analyzer Settings Set CW frequency Set CW frequency, Set channel width/span Power range Depends on USB sensor Depends on channel width and attenuator setting.

Warm-up time 30 minutes to meet accuracy

specifications

Accuracy Depends on USB sensor InstAlign accuracy: ± 0.5 dB typical for a CW signal. Since the

Programmable Yes, via SCPI Yes, via SCPI Physical connection The power sensor can easily be

moved to the measurement point,

with a USB cable connecting the detector to FieldFox.

FieldFox source control Yes, on/off, and nominal power level

control

Option 310 Built-in power meter (or channel power meter)

Option 310 is a channelized power measurement capability built

into FieldFox analyzers. Maximum bandwidth is 100 MHz.

Tuned receiver, so measures frequencies within defined channel bandwidth

No warm-up time required

measurement is within a certain frequency channel or bandwidth, to make an accurate measurement, the user needs to know the

exact center frequency and the signal’s bandwidth and set those

accurately.

The measurement point needs to be connected to FieldFox’s RF

input port. If a RF jumper cable is used, the user needs to account for the loss of the cable with an offset value (can be entered into the analyzer).

No access to FieldFox’s source from the built-in power meter mode

09 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

FAQs – Applicable To All FieldFox RF and Microwave Analyzers (continued)

Question Answer

3. What do I need to get GPS

information?

4. What is the connector for Option

309, DC output?

5. What are the connectors for

the Reference/Trigger In and Reference/ Trigger Out?

6. What is Option 030 Remote

control capability?

7. What USB sensor is required for

Option 330?

8. What measurement capabilities

are included with Option 330?

9. What is included with Option 208? Option 302, USB power sensor measurements, includes CW power measurements (one frequency at a time). With

(1) The recommended GPS solution is to order:

– Option 307 - built-in GPS receiver – A GPS antenna such as N9910X-825 – Other GPS antennas can also be used – The GPS connector on the instrument is SMA (f)

(2) Alternatively, you can purchase a USB-based GPS receiver. You do not need to purchase any FieldFox options

for the USB-based GPS to work. However, the USB-based GPS only provides time and location data, and time synchronization capability. It cannot be used to increase the frequency accuracy of the instrument.

The DC output has a SMB (m) connector. Recommend ordering N9910X Option 713 bias-tee power cable SMB (f)

to BNC (m).

The connector for the Ref/Trig In is SMA (f). Recommend ordering N9910X Option 712 Trig/Ref in SMA (m) to BNC

(f) cable.

The connector for the Ref/Trig Out is SMB (m). Recommend ordering N9910X Option 713 bias-tee power cable

SMB (f) to BNC (m).

(1) Option 030 provides a license for FieldFox to allow remote control via an iOS device.

(2) Not supplied by user, but necessary for operation of Option 030 are:

– iOS device: iPad, iPhone, or iPod Touch with iOS 6.1 or higher with free FieldFox app – A WiFi or 3G/4G network connection between FieldFox and iOS device

Option 330 or pulse measurements requires a Keysight USB peak power sensor. Visit www.keysight.com/find/usbsensorsforfieldfox for a list of supported peak power sensors. Average power sensors

cannot be used with Option 330, only peak power sensors. The peak power sensor needs to be purchased separately.

Average power, peak power, and peak to average ratio Analog gauge display and digital display, dBm and watts Relative/absolute measurements, dB or %, minimum and maximum limits Trace graph for pulse profiling with gating

Rise time, fall time, pulse width, pulse period, pulse repetition frequency

Option 208 added, you can make swept-frequency power measurements. You can plot source power, gain, and receive power versus frequency. Additionally, the source frequency can be offset from the receiver frequency. The power sensor needs to be purchased separately.

10 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

FieldFox Microwave Vector Network Analyzers

FieldFox microwave vector network analyzer models

St ep 1. Select the model that provides the desired frequency range.

Model Description Frequency Test port connectors

N9925A 9 GHz FieldFox microwave VNA 30 kHz to 9 GHz Type-N (f) N9926A 14 GHz FieldFox microwave VNA 30 kHz to 14 GHz Type-N (f) N9 927A 18 GHz FieldFox microwave VNA 30 kHz to 18 GHz Type-N (f) N9928A 26.5 GHz FieldFox microwave VNA 30 kHz to 26.5 GHz 3.5 mm (m)

A standard N992xA FieldFox microwave VNA includes transmission/reflection measurement capability. Additional functionality such as full 2-port S-parameters can be added using the options listed below.

Step 2. Select optional measurement capabilities. Any of these options can easily be added as a software upgrade in the future.

FieldFox microwave vector network analyzer options

Option Description Prerequisite options/notes

Vector network analysis / CAT

010 VNA time domain Recommend 211 112 QuickCal See page 11, FAQ #7 211 VNA full 2-port S-parameters 212 1-port mixed-mode S-parameters Requires 211

215 TDR cable measurements Requires 305 305 Cable and antenna analyzer - 308 Vector voltmeter 211 required to obtain full VVM functionality. See page 11, FAQ #5

Power measurements

System features

030 Remote control capability Requires an iOS device 307 GPS receiver Need to order GPS antenna, N9910X-825. See page 9, FAQ #3 309 DC bias variable-voltage source -

1. List of compatible sensors available from www.keysight.com/find/fieldfoxsuppor t

11 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

FieldFox Microwave Vector Network Analyzer FAQs

Question Answer

1. What is included with a base

N992xA analyzer?

2. What is included with N992xA Option 211?

3. What is included with N992xA Option 010?

4. What is included with N992xA

Option 305?

5. What is included with N992xA

Option 308?

6. If I have the full 2-port VNA with

time domain, why would I order

Option 305? What additional functionality is available?

7. What is included with N992xA

Option 112?

Additional FAQs on pages 8 and 9. FAQs on pages 8 and 9 apply to all microwave FieldFox models.

– Measurements: Transmission/reflection or S21 and S11, magnitude and phase – Calibrations: CalReady, OSL, response, and enhanced response cal – Option 211 adds full 2-port S-parameter capability – Measurements: All four S-parameters (S11, S21, S22, S12), magnitude and phase – Calibrations: CalReady, OSL, response, enhanced response, and full 2-port cal – S11/S21 in time domain. To get time domain data for all four S-parameters and full 2-port cal, order Option 211 – View both time and frequency domain data at the same time – Low-pass, impulse, and band-pass modes – Minimum, normal, and maximum window – Gating – Measurements: DTF (dB, linear, VSWR), return loss and DTF, return loss (dB), and 1-port cable loss, 2-port

insertion loss – TDR (linear, ohm). TDR measurements require Option 215, in addition to Option 305. – Calibrations: CalReady, OSL, and response cal

– N992xA with Option 308: 1-port cable trimming, 2-port transmission – N992xA with Options 308 and 211: 1-port cable trimming, 2-port transmission, A/B and B/A – Note: A/B and B/A measurements require an external source

CAT mode’s basic measurements are similar to VNA measurements. The features listed below are often used for

distance-to-fault cable testing and are only available in CAT mode:

– 3-peak marker tracking for finding faults for DTF measurements – 1-port cable loss – Cable type selection and editing, includes the cable’s velocity factor and loss – QuickCal is included with Option 112.

– 1-port and enhanced response QuickCal with a base analyzer – 1-port, enhanced response, and 2-port QuickCal with a full 2-port analyzer (one that has Option 211).

– QuickCal is most accurate for DUTs with 7/16 and Type-N connectors and measurement uncertainties are

provided for frequencies 18 GHz. Reduced accuracy for DUTs with 3.5 mm (m), SMA (m), or other male coaxial

connectors; performance is unspecified. QuickCal is not recommended for DUTs with 3.5 mm (f), SMA (f), or

other similar female connectors. QuickCal is not applicable to waveguide.

12 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

FieldFox Microwave Spectrum Analyzers

FieldFox microwave spectrum analyzer models

St ep 1. Select the model that provides the desired frequency range.

Model Description Frequency range

N9935A 9 GHz FieldFox microwave spectrum analyzer 100 kHz to 9 GHz Type-N (f) N9936A 14 GHz FieldFox microwave spectrum analyzer 100 kHz to 14 GHz Type-N (f) N9 937A 18 GHz FieldFox microwave spectrum analyzer 100 kHz to 18 GHz Type-N (f) N9938A 26.5 GHz FieldFox microwave spectrum analyzer 100 kHz to 26.5 GHz Type-N (f) N9960A 32 GHz FieldFox microwave spectrum analyzer 9 kHz to 32 GHz NMD 2.4 mm (m) N9961A 44 GHz FieldFox microwave spectrum analyzer 9 kHz to 44 GHz NMD 2.4 mm (m) N9962A 50 GHz FieldFox microwave spectrum analyzer 9 kHz to 50 GHz NMD 2.4 mm (m)

Step 2. Select optional measurement capabilities. Any of these options can easily be added as a software upgrade in the future.

FieldFox microwave spectrum analyzer options

Option Description Prerequisite options/notes

Spectrum analyzer

100

209 Extended range transmission analysis (ERTA) Requires 220. Recommend 307. Requires two FieldFoxes. See page 6, FAQ # 10. 220 Full-band tracking generator CW, CW coupled, and tracking 235

236 238 Spectrum analyzer time gating - 312 Channel scanner 320 Reflection measurements 320 requires 220 on all models. On N9938A specifically, 320 also requires 100.

350 Real-time spectrum analyzer (RTSA) 351 I/Q Analyzer (IQA) 355 Analog demodulation -

Power measurements

208 USB power sensor meas. vs. frequency Requires 302 302 USB power sensor support Need to order USB power sensor 310 Built-in power meter No power sensor required. See page 8, FAQ #1 330 Pulse meas. with USB peak power sensor Need to order USB peak power sensor. See page 9, FAQs #7 and #8

System features

030 Remote control capability Requires an iOS device 307 GPS receiver Need to order GPS antenna, N9910X-825. See page 9, FAQ #3 309 DC bias variable-voltage source -

Windows based software

896 01B 89600 VSA Software

1. The spectrum analyzer can be tuned to 5 kHz.

2. Order Option 100 for 3.5 mm (m) test port connectors. With N9938A-100, the spectrum analyzer is built with 3.5 mm test port connectors instead of the

3. Requires CPU2 fast processor. See page 6, FAQ #13

4. List of compatible power sensors available from w ww.keysight.com/find/fieldfoxsupport

3.5 mm (m) connectors Only available on N9938A. Option 100 is only available at time of purchase. It is not available as an upgrade.

Pre-amplifier -

Interference analyzer and spectrogram

standard Type-N (f). Option 100 is a prerequisite for Option 320 for N9938A.

Recommend 235. See page 6, FAQ # 12

Test port connectors

13 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

FieldFox Spectrum Analyzer FAQs

Question Answer

1. What is included with the basic spectrum

analyzer?

2. What is included with Option 236? – Interference analyzer and spectrogram

3. What is included with Option 320? – Return loss and VSWR

4. What is the difference between Option 320 and

the CAT mode on the combo base model?

5. What is included with Option 355? FieldFox analog demodulation has two parts: (1) Tune and listen, and (2) AM/FM metrics. Tune and

Additional FAQs on pages 8 and 9. FAQs on pages 8 and 9 apply to all microwave FieldFox models.

– Basic spectrum analysis, four traces, different detector types, radio standard selection, limit lines – Channel power, occupied bandwidth, adjacent channel power – AM/FM tune and listen, field strength measurements, antenna factors, frequency counter

marker

– Trace playback and recording

– Normalization using data/memory

Option 320 on the N993xA/N996xA SA offers RL and VSWR. CAT mode on the N991xA/N995xA

combo analyzers offers RL and VSWR, DTF, insertion loss, and also various calibration capabilities such as QuickCal and OSL.

listen is available as a standard feature on all N993xA and N996xA FieldFox spectrum analyzers. AM/FM metrics becomes available when Option 355 is purchased. AM/FM metrics provides the user with RF spectrum view, demodulated baseband signal waveform, carrier power, frequency deviation,

SINAD and more.

Documentation

By default, a printed copy of the User’s Guide is not included in FieldFox orders. If you wish to receive the printed User’s Guide, please order N99xxA Option ABA.

Option Description Notes

N99xxA-0B0 Do not include User’s Guide N99xxA-ABA Printed User’s Guide in English

The latest FieldFox User’s Guide (manual) is available online from: www.keysight.com/find/fieldfoxsupport

The Service Guide, SCPI Programming Guide, Quick Reference Guide, and Data Link software help file can also be found via the website above.

14 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

You Can Upgrade!

Upgrades

Information on upgrades is available from: www.keysight.com/find/fieldfoxsupport

FieldFox microwave (combination) upgrades N9913AU, N9914AU, N9915AU, N9916AU, N9917AU, N9918AU, N9950AU, N9951AU, N9952AU

Option Description Upgrade contents Additional requirements

010 VNA time domain analysis License key 210 030 Remote control capability License key None 112 Enable QuickCal License key None (Does not apply to N995xAU) 208 USB power sensor measurements versus frequency License key 302 209 Extended range transmission analysis (ERTA) License key 233 and 210 210 VNA transmission and reflection License key None 211 VNA full 2-port S-parameters License key 210 212 Mixed-mode S-parameters License key 210 and 211 215 TDR cable measurements License key None 233 Spectrum analyzer License key None 235 Preamplifier License key 233 236 Interference analyzer and spectrogram License key 233 238 Spectrum analyzer time gating License key 233 302 External USB power sensor support License key None 307 GPS receiver License key None 308 Vector voltmeter License key None 309 DC bias variable-voltage source License key None 310 Built-in power meter License key None 312 Channel scanner License key 233 330 Pulse measurements License key None

350 Real-time spectrum analyzer (RTSA) License key 351 I/Q Analyzer (IQA) License key 355 Analog demodulation License key 233

1. 209 is a system based on two FieldFoxes. See page 6, FAQ #10, for a detailed description of the system requirements.

2. Requires CPU2 fast processor. See page 6, FAQ #13.

Options can be added after your initial purchase.

233 233

GRADE

FieldFox VNA upgrades N9925AU, N9926AU, N9927AU, N9928AU

Option Description Upgrade contents Additional requirements

010 VNA time domain analysis License key None 030 Remote control capability License key None 112 Enable QuickCal License key None 208 USB power sensor measurements versus frequency License key 302 211 VNA full 2-port S-parameters License key None 212 Mixed-mode S-parameters License key 211 215 TDR cable measurements License key 305 302 External USB power sensor support License key None 305 Cable and antenna analyzer License key None 307 GPS receiver License key None 308 Vector voltmeter License key None 309 DC bias variable-voltage source License key None 310 Built-in power meter License key None 330 Pulse measurements License key None

15 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

Upgrades (continued)

Information on upgrades is available from: www.keysight.com/find/fieldfoxsupport

FieldFox SA upgrades N9935AU, N9936AU, N9937AU, N9938AU, N9960AU, N9961AU, N9962AU

Option Description Upgrade contents Additional requirements

030 Remote control capability License key None 100 3.5 mm connectors Not applicable Not applicable 208 USB power sensor measurements versus frequency License key 302 209 Extended range transmission analysis (ERTA) License key 220 Full-band tracking generator License key None 235 Preamplifier function License key None 236 Interference analyzer and spectrogram License key None 238 Spectrum analyzer time gating License key None 302 External USB power sensor support License key None 307 GPS receiver License key None 309 DC bias variable-voltage License key None 310 Built-in power meter License key None 312 Channel scanner License key None 320 Reflection measurements License key

330 Pulse measurements License key None

350 Real-time spectrum analyzer (RTSA) License key 351 I/Q Analyzer (IQA) License key

355 Analog demodulation License key None

220

– Option 220 for all models – Option 100 and 220 for N9938A

None None

1. 209 is a system based on two FieldFoxes. See page 6, FAQ #10, for a detailed description of the system requirements.

2. On N9938A, Option 320 is only available as a sof tware upgrade if the spectrum analyzer is already equipped with Option 100, which is 3.5 mm connectors on the test por t. Option 100 must have been ordered at the time of original purchase. It cannot be upgraded later.

3. Requires CPU2 fast processor. See page 6, FAQ #13.

FieldFox RF and microwave analyzers hardware upgrades

Model Number/

1,2

Option

N9910HU-100 N9913/14/15/16/17A processor upgrade Improved performance for

N9910HU-20 0 N9925/26/27A processor upgrade Improved performance for

N9910HU-300 N9935/36/37A processor upgrade Improved performance for

N9910HU-4 00 N9918/28/38A processor upgrade Improved performance for

1. Upgrades are not available for FieldFox analyzers with serial number prefix starting with MY5607/SG5607/US5607, as these analyzers already have the improved hardware.

2. Please contact your local Keysight Ser vice Center for instructions on how and where to send the instrument, and how to order the factory upgrades.

Description Upgrade contents Additional requirements

Return to service center only

N9 915/16 / 17A models

Return to service center only

N9925/26/27A models

Return to service center only

N9935/36/37A models

Return to service center only

N9918/28/38A models

16 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

Calibration Kits

FieldFox analyzers support most standard HP/Agilent/Keysight mechanical calibration kits and all Keysight USB ECal modules. Custom calibration kits can be created and uploaded to FieldFox using Data Link software.

Model Description Connector Frequency range Components

7-16

N9910X-802 3-in-1 OSL cal kit 7/16 (m) DC to 4 GHz open, short, load (all male) N9910X-803 3-in-1 OSL cal kit 7/ 16 ( f ) DC to 4 GHz open, short, load (all female) 85038A Standard cal kit 7/16 DC to 7.5 GHz open, short, load (both female and male)

Type-N, 50 Ω

N9910X-800 3-in-1 OSL cal kit Type-N (m) DC to 6 GHz open, short, load (all male) N9910X-801 3-in-1 OSL cal kit Type-N (f) DC to 6 GHz open, short, load (all female) 85032E Economy cal kit Type-N (m) DC to 6 GHz open, short, load (all male) 85514A 4-in-1 OSLT cal kit Type-N (m) DC to 9 GHz open, short, load, thru (all male) 85515A 4-in-1 OSLT cal kit Type-N (f) DC to 9 GHz open, short, load, thru (all female) 85032F Standard cal kit Type-N DC to 9 GHz open, short, load (both female and male) 85518 A 4-in-1 OSLT cal kit Type-N (m) DC to 18 GHz open, short, load, thru (all male) 85519 A 4-in-1 OSLT cal kit Type-N (f) DC to 18 GHz open, short, load, thru (all female) 85054D Economy cal kit Type-N DC to 18 GHz open, short, load, thru (both female and male) 85054B Standard cal kit Type-N DC to 18 GHz open, short, fixed load, sliding load (both female and male) 85092C ECal, 2-ports Type-N 300 kHz to 9 GHz connectors configurable N4690B/C ECal, 2-ports Type-N 300 kHz to 18 GHz connectors configurable N7550A ECal economy, 2-ports Type-N DC to 4 GHz connectors configurable N7551A ECal economy, 2-ports Type-N DC to 6.5 GHz connectors configurable N7552A ECal economy, 2-ports Type-N DC to 9 GHz connectors configurable N7553A ECal economy, 2-ports Type-N DC to 14 GHz connectors configurable N7554A ECal economy, 2-ports Type-N DC to 18 GHz connectors configurable

Type-N, 75 Ω

85036B Standard cal kit Type-N 75 Ω DC to 3 GHz open, short, load (both female and male) 85036E Economy cal kit Type-N(m) 75 Ω DC to 3 GHz open, short, load, all male 85096C ECal, 2-ports Type-N(m) 75 Ω 300 kHz to 3 GHz connectors configurable

3.5 mm

85520A 4-in -1 OSLT 3.5 mm (m) DC to 26.5 GHz open, short, load, thru (all male) 85521A 4-i n-1 OSLT 3.4 mm (f) DC to 26.5 GHz open, short, load, thru (all female) 85033D/E Economy cal kit 3.5 mm DC to 6/9 GHz open, short, fixed load (both female and male) 85052D Economy cal kit 3.5 mm DC to 26.5 GHz open, short, fixed load (both female and male) 85052B Standard cal kit 3.5 mm DC to 26.5 GHz open, short, fixed load, sliding load (both female and male) 85052C Precision TRL kit 3.5 mm DC to 26.5 GHz open, short, fixed load (both female and male), two line lengths 85093C ECal, 2-ports 3.5 mm 300 kHz to 9 GHz connectors configurable N4 691B ECal, 2-ports 3.5 mm 300 kHz to 26.5 GHz connectors configurable N7550A ECal economy, 2-ports 3.5 mm DC to 4 GHz connectors configurable N7551A ECal economy, 2-ports 3.5 mm DC to 6.5 GHz connectors configurable N7552A ECal economy, 2-ports 3.5 mm DC to 9 GHz connectors configurable N7553A ECal economy, 2-ports 3.5 mm DC to 14 GHz connectors configurable N7554A ECal economy, 2-ports 3.5 mm DC to 18 GHz connectors configurable N7555A ECal economy, 2-ports 3.5 mm DC to 26.5 GHz connectors configurable

2.92 mm (same as K connector)

85561A 4-in-1 OSLT cal kit 2.92 mm (f ) DC to 40 GHz open, short, fixed load, thru (all female) 85562A 4-in-1 OSLT cal kit 2.92 mm (m) DC to 40 GHz open, short, fixed load, thru (all male) 85056KE013Standard cal kit 2.92 mm DC to 40 GHz open, short, fixed load, sliding load (both female and male) 85056KE024Economy cal kit 2.92 mm DC to 40 GHz open, short, fixed load (both female and male) N4692A ECal 2.92 mm 10 MHz to 40 GHz connectors configurable

1. Component list shows calibration components. Some cal kits also include adapters.

2. Recommend ordering quantity 2 of N9910X Option 846, 50 to 75 Ω adapter.

3. Same as Maury’s 8770C47

4. Same as Maury’s 8770D47

17 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

Calibration Kits (continued)

Model Description Connector Frequency range Components

2.4 mm

85563A 3-in-1 OSL cal kit 2.4 mm (f) DC to 50 GHz open, short, fixed load (all female) 85564A 3-in-1 OSL cal kit 2.4 mm (m) DC to 50 GHz open, short, fixed load (all male) 85056D Economy cal kit 2.4 mm DC to 50 GHz open, short, fixed load (both female and male) 85056A Standard cal kit 2.4 mm DC to 50 GHz open, short, load, fixed load, sliding load (both female and male) N4693A ECal 2.4 mm 10 MHz to 50 GHz connectors configurable

Waveguide

N9 911X-11x Econ. waveguide cal kit W R-137 5.38 to 8.18 GHz short, termination, offset length N9 911X-21x Econ. waveguide cal kit WR-90 8.2 to 12.5 GHz short, termination, offset length N9 911X-31x Econ. waveguide cal kit WR-62 11.9 to 18 GHz short, termination, offset length N9 911X-41x Econ. waveguide cal kit WR-42 17.6 to 26.7 GHz short, termination, offset length X11644A Waveguide cal kit WR-90 8.2 to 12.4 GHz short, shim, termination, standard section

P11644A Waveguide cal kit WR-62 12.4 to 18 GHz short, shim, termination, standard section K11644A Waveguide cal kit WR-42 18 to 26.5 GHz short, shim, termination, standard section R11644A Waveguide cal kit WR-28 26.5 to 40 GHz short, shim, termination two straight sections Q116 44A Waveguide cal kit WR-22 33 to 50 GHz short, shim, termination, two straight sections U116 44A Waveguide cal kit W R-19 40 to 60 GHz short, shim, termination, two straight sections

18 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

Accessories

Cables

All cables listed below are rugged phase-stable cables.

Model Cable connector Other cable connector Max frequency Length (ft) Length (m)

N9 910X-700 Type-N (m) Type-N (f) 18 GHz 3.28 ft 1 m N9 910X-701 Type-N (m) Type-N (m) 18 GHz 3.28 ft 1 m N9 910X-708 3.5 mm (m) 3.5 mm (f) 26.5 GHz 3.28 ft 1 m N9 910X-709 3.5 mm (f) 3.5 mm (f) 26.5 GHz 3.28 f t 1 m N9910X-714 2.4 mm (f) 2.4 mm (m) 50 GHz 3.28 ft 1 m N9 910X-715 2.4 mm (f) 2.4 mm (f) 50 GHz 3.28 ft 1 m N9910X-810 Type-N (m) Type-N (m) 6 GHz 5 ft 1.5 m N9910X-811 Type-N (m) Type-N (f) 6 GHz 5 ft 1.5 m N9910X-812 Type-N (m) Type-N (m) 8 GHz 12 ft 3.6 m N9910X-813 Type-N (m) Type-N (f) 8 GHz 12 f t 3.6 m N9910X-814 Type-N (m) 7/16 (m) 6 GHz 5 ft 1.5 m N9910X-815 Type-N (m) 7/16 (m) 6 GHz 12 f t 3.6 m N9910X-816 Type-N (m) Type-N (f) 6 GHz 3.28 ft 1 m N9910X-817 Type-N (m) Type-N (m) 6 GHz 3.28 ft 1 m

Antennas

N9910X-820 Antenna, directional, multiband, 800 to 2500 MHz, 10 dBi, Type-N (f) N9910X-821 Antenna, telescopic whip, 70 MHz to 1 GHz, BNC (m) N9910X-822 Antenna, directional, log periodic, 600 MHz to 9 GHz, Type-N(f) N9910X-823 N9910X-824 N9910X-825

RF and microwave adapters

83059A Coaxial adapter, 3.5 mm (m) to 3.5 mm (m), 26.5 GHz 83059B Coaxial adapter, 3.5 mm (f) to 3.5 mm (f), 26.5 GHz 83059C Coaxial adapter, 3.5 mm (m) to 3.5 mm (f), 26.5 GHz N9910X-601 Coaxial adapter, NMD 2.4 mm (f) to Type-N (f), 50-ohm, 18 GHz N9910X-602 Coaxial adapter, NMD 2.4 mm (f) to 2.92 mm/K (f), 40 GHz N9910X-603 Coaxial adapter, NMD 2.4 mm (f) to 3.5 mm (f), 26.5 GHz N9910X-843 Coaxial adapter, Type-N (m) to 7/16 DIN (f) N9910X-845 Adapter kit: Type-N (f) to 7/16 DIN (f), Type-N (f) to 7/16 DIN (m), Type-N (f) to Type-N (f) N9910X-846 Coaxial adapter, Type-N (m) 50 ohm to Type-N (f) 75 ohm N9910X-847 Adapter kit: Type-N (f) to TNC (m) adapter, Type-N (f) to TNC (f) adapter, 11 GHz N9910X-848 Coaxial adapter, Type-N (f) to 3.5 mm (f), 18 GHz N9910X-849 Coaxial adapter, Type-N (f) to 3.5 mm (m), 18 GHz N9910X-850 Coaxial adapter, Type-N (m) to Type-N (m), 18 GHz N9910X-851 Coaxial adapter, Type-N (f) to Type-N (f), 18 GHz N9910X-852 Coaxial adapter, Type-N (m) to Type-N (f), 18 GHz N9910X-856 Coaxial adapter, 2.4 mm (f) to 2.4 mm (f), 50 GHz N9910X-857 Coaxial adapter, 2.4 mm (f) to 2.92 mm/K (f), 40 GHz

Other RF and microwave accessories

N9910X-860 Fixed attenuator, 40 dB, 100 W, DC to 3 GHz, Type-N (m) to Type-N (f) N9910X-861 Fixed attenuator, 40 dB, 50 W, DC to 8.5 GHz, Type-N (m) to Type-N (f) N9 910X- 874 External bias-tee, 2.5 MHz to 6 GHz, 1 W, 0.5 A N9910X-712 Trig/Ref in Cable SMA (m) to BNC (f), 1 m or 3.28 ft N9910X-713 Bias-tee power cable SMB (f) to BNC (m), 1 m or 3.28 ft

Other FieldFox accessories

N9910X-870 Extra battery N9910X-872 External battery charger N9910X-873 AC/DC adapter N9910X-875 DC car charger and adapter N9910X-880 Extra soft carrying case with backpack and shoulder strap N9910X-881 Hard transit case N9910X-886 Torque wrench, 17 mm, 90 N-cm (8in-lb), recommended for N995xA and N996xA analyzers

Antenna, cellular narrowband, 824 to 869 MHz, Type-N (f) Antenna, cellular narrowband, PCS 1850 to 1990 MHz, Type-N (f)

Antenna, GPS, active, SMA (m)

19 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

Accessories (continued)

Below are images for a subset of FieldFox accessories. Complete list of accessories are on pages 15 to 17 of this document.

Description Accessory

N9 910X-701

Type-N (m) to Type-N (m) cable, 3.28 ft

N9 910X-708

3.5 mm (m) to 3.5 mm (f) cable, 3.28 ft

N9910X-820

Antenna, directional

N9910X-823

Antenna, cellular narrowband

N9910X-822

Antenna, directional

Description Accessory

N9910X-811 Type-N (m) to Type-N (f) cable, 5 ft

N9910X-812

Type-N (m) to Type-N (m) cable, 12 ft

N9910X-816

Type-N (m) to Type-N (f) cable, 3.28 ft

N9910X-821

Antenna, telescopic whip

N9910X-848 Coaxial adapter, Type-N(f) to 3.5 mm (f)

N9910X-825

Antenna, GPS, active

N9910X-870 Extra battery

N9910X-872 External battery charger

N9910X-881

Hard transit case

N9910X-875 DC car charger and adapter

N9910X-873

AD/DC adapter

N9 910X- 874 External bias-tee

20 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

Accessories (continued)

Below are images for a subset of FieldFox accessories. Complete list of accessories are on pages 15 to 17 of this document.

Description Accessory

N4690B

2-port ECal, Type-N, 18 GHz

N9910X-800

3-in-1 OSL cal kit, Type-N (m), 6 GHz

N991X0-801

3-in-1 OSL cal kit, Type-N (f), 6 GHz

85514A 4-in-1 OSLT cal kit, Type-N (m) 9 GHz

85515A 4-in-1 OSLT cal kit, Type-N (f), 9 GHz

Description Accessory

N4 691B 2-port ECal, 3.5 mm, 26.5 GHz

85520A 4-in-1 OSLT cal kit, 3.5 mm (m), 26.5 GHz

85521A 4-in-1 OSLT cal kit, 3.5 mm (f), 26.5 GHz

85033D/E

3.5 mm cal kit, 9 GHz

85052D

3.5 mm cal kit, 26.5 GHz

85518 A

4-in-1 OSLT cal kit, Type-N (m), 18 GHz

85519 A

4-in-1 OSLT cal kit, Type-N (f), 18 GHz

85054D

Economy cal kit, Type-N, 18 GHz

N9911X-211/212/213/214 WR-90 economical cal kit

N4692A

2.92 mm, 2-port ECal, 40 GHz

N4693A

2.4 mm 2-port ECal, 50 GHz

85056D

2.4 mm cal kit, 50 GHz

X11644A WR-90 standard cal kit

21 | Keysight | FieldFox Handheld Analyzers - Configuration Guide

Evolving Since 1939

Our unique combination of hardware, software, services, and people can help you reach your next breakthrough. We are unlocking the future of technology.

From Hewlett-Packard to Agilent to Keysight.

myKeysight

www.keysight.com/find/mykeysight

A personalized view into the information most relevant to you.

http://www.keysight.com/find/emt_product_registration

Keysight Services

www.keysight.com/find/service

Keysight Services can help from acquisition to renewal across your instrument’s lifecycle. Our comprehensive service offerings—onestop calibration, repair, asset management, technology refresh, consulting, training and more—helps you improve product quality and lower costs.

Keysight Assurance Plans

www.keysight.com/find/AssurancePlans

Up to ten years of protection and no budgetary surprises to ensure your instruments are operating to specification, so you can rely on accurate measurements.

Keysight Channel Partners

www.keysight.com/find/channelpartners

Get the best of both worlds: Keysight’s measurement expertise and product breadth, combined with channel partner convenience.

www.keysight.com/find/fieldfox

For more information on Keysight Technologies’ products, applications or services, please contact your local Keysight office. The complete list is available at:

www.keysight.com/find/contactus

Americas

Canada (877) 894 4414 Brazil 55 11 3351 7010 Mexico 001 800 254 2440 United States (800) 829 4444

Asia Pacific

Australia 1 800 629 485 China 800 810 0189 Hong Kong 800 938 693 India 1 800 11 2626 Japan 0120 (421) 345 Korea 080 769 0800 Malaysia 1 800 888 848 Singapore 1 800 375 8100 Taiwan 0800 047 866 Other AP Countries (65) 6375 8100

Europe & Middle East

Austria 0800 001122 Belgium 0800 58580 Finland 0800 523252 France 0805 980333 Germany 0800 6270999 Ireland 1800 832700 Israel 1 809 343051 Italy 800 599100 Luxembourg +32 800 58580 Netherlands 0800 0233200 Russia 8800 5009286 Spain 800 000154 Sweden 0200 882255 Switzerland 0800 805353

Opt. 1 (DE) Opt. 2 (FR) Opt. 3 (IT)

United Kingdom 0800 0260637

For other unlisted countries:

www.keysight.com/find/contactus

(BP-9-7-17)

DEKRA Certified

ISO9001 Quality Management System

www.keysight.com/go/quality

Keysight Technologies, Inc. DEKRA Certified ISO 9001:2015 Quality Management System

This information is subject to change without notice. © Keysight Technologies, 2014-2017 Published in USA, September 28, 2017 5990-9836EN

www.keysight.com

Keysight N9917A, N9914A, N9918A, N9950A, N9951A Configuration Manual

Specifications and Main Features

Frequently Asked Questions

User Manual