Keysight E5071C, E5092A Configuration Manual

Keysight Technologies

E5071C Network Analyzer

– 9 kHz to 4.5/6.5/8.5 GHz
– 100 kHz to 4.5/6.5/8.5 GHz (with bias tees)
– 300 kHz to 14/20 GHz (with bias tees)

E5092A Congurable Multiport Test Set

Conguration Guide

02 | Keysight | E5071C Network Analyzer - Conguration Guide

This configuration guide describes standard configurations, op­tions, accessories and peripherals for the E5071C ENA network
analyzer. Refer to the ENA brochure for a complete description of
the ENA network analyzer and the E5092A configurable multiport

test set.

E5071C ENA Network Analyzer

The ENA is an integrated network analyzer with a two- or four­port S-parameter test set, a synthesized RF source, a 10.4-inch
color LCD, and a hard disk drive. A 3-year return-to-Keysight
Technologies, Inc. service warranty is included with the each ENA

network analyzer.

Step 1: Select frequency range, number of test
ports, and with or without bias tees

Up to 4.5 GHz range

9 kHz to 4.5 GHz (without bias tees)
E5071C-240 2-port S-parameter test set
E5071C-440 4-port S-parameter test set

100 kHz to 4.5 GHz (with bias tees)

E5071C-245 2-port S-parameter test set
E5071C-445 4-por t S-parameter test set

Up to 6.5 GHz range

9 kHz to 6.5 GHz (without bias tees)
E5071C-260 2-port S-parameter test set
E5071C-460 4-port S-parameter test set

100 kHz to 6.5 GHz (with bias tees)

E5071C-265 2-port S-parameter test set
E5071C-465 4-port S-parameter test set

Up to 8.5 GHz range

9 kHz to 8.5 GHz (without bias tees)
E5071C-280 2-port S-parameter test set
E5071C-480 4-port S-parameter test set

100 kHz to 8.5 GHz (with bias tees)

E5071C-285 2-port S-parameter test set
E5071C-485 4-port S-parameter test set

Up to 14 GHz range3

300 kHz to 14 GHz (with bias tees)

E5071C-2D5 2-port S-parameter test set
E5071C-4D5 4-port S-parameter test set

1. Order the 82357B USB/GPIB interface at the same time if you want to
control power meters with the E5071C. This will allow you to conduc t
scalar mixer calibrations (SMC), power calibrations, or receiver calibra­tions af ter power calibrations.

2. E5071C-TDR is a superset of E5071C-010. To add option TDR, you do not
need to have option 010 already installed; however, you can have both
option 010 and TDR installed in one instrument

3. Consider purchasing Keysight 20mm TORQUE WRENCH 8710-1764 for
NMD 3.5 mm(f ) test port connector.

Up to 20 GHz range3

300 kHz to 20 GHz (with bias tees)

E5071C-2K5 2-port S-parameter test set
E5071C-4K5 4-port S-parameter test set
Step 2: Select time base
E5071C-1E5 High stability time base
E5071C-UNQ Standard stability time base

Step 3: Select hard disk drive

E5071C-017 Removable hard disk drive
E5071C-019 Standard hard disk drive

Step 4: Choose additional options (Optional)

E5 071C - 0 0 81 Frequency offset mode
E5 071C -TDR2 Enhanced time domain analysis

E5071C-010 Time domain analysis
E5071C-790 Measurement Wizard Assistant software

Step 5: Choose accessories (Optional)

E5071C-1CM Rack mount kit,
E5071C-1CN Front handle kit
E5071C-1CP Rack mount and front handle kit
E5071C-810 Adds a keyboard
E5071C-820 Adds a mouse

Step 6: Choose certification documentation
(Optional)

E5071C-1A7 ISO 17025 compliant calibration
E5071C-A6J ANSI Z540 compliant calibration

Step 7: Choose your warranty service
(Optional)

5 year return-to Keysight warranty and service

Documentation

The documentation for the E5071C is located in the
Online Help system for the E5071C ENA network analyzer.
The ENA Service Guide and Online Help system are also available
on the Web site:

www.keysight.com/find/ena

Additional product information

For additional product information, refer to the ENA
brochure available on the Web site:

www.keysight.com/find/ena

03 | Keysight | E5071C Network Analyzer - Conguration Guide

Port 1

R1 A R2 B R3 C R4 D

Port 2 Port 3 Port 4

Port 1

R1 A R2 B

Port 2

Receiver assignment

2-por t test set option 4-port test set option

04 | Keysight | E5071C Network Analyzer - Conguration Guide

E5071C ENA Network Analyzer

Options

To add options to a product, order the corresponding item number.

Option1 Description Additional information

Tes t se t
Option 240
Option 440
Option 245
Option 445
Option 260
Option 460
Option 265
Option 465
Option 280
Option 480
Option 285
Option 485

Option 2D5
Option 4D5
Option 2K5
Option 4K5

Time base
Option UNQ
O ptio n 1E5

Hard disk drive
O ption 017
Option 019

Additional features
Option 008

2

Option TDR

3

Option 010
Option 790

4

Accessories
Option 1CM

Option 1CN
Option 1CP
Option 810
Option 820

Calibration documentation
Option 1A7
Option A6J

2-port test set, 9 kHz to 4.5 GHz without bias tees
4-port test set, 9 kHz to 4.5 GHz without bias tees
2-port test set, 100 kHz to 4.5 GHz with bias tees
4-port test set, 100 kHz to 4.5 GHz with bias tees
2-port test set, 9 kHz to 6.5 GHz without bias tees
4-port test set, 9 kHz to 6.5 GHz without bias tees

Test port connector: Type-N (f)
2-port test set, 100 kHz to 6.5 GHz with bias tees
4-port test set, 100 kHz to 6.5 GHz with bias tees
2-port test set, 9 kHz to 8.5 GHz without bias tees
4-port test set, 9 kHz to 8.5 GHz without bias tees
2-port test set, 100 kHz to 8.5 GHz with bias tees
4-port test set, 100 kHz to 8.5 GHz with bias tees

2-port test set, 300 kHz to 14 GHz with bias tees
4-port test set, 300 kHz to 14 GHz with bias tees

Test port connector: 3.5 mm (m)
2-port test set, 300 kHz to 20 GHz with bias tees
4-port test set, 300 kHz to 20 GHz with bias tees

Standard stability time base
High stability time base Adds a higher stability time base reference.

Removable hard disk drive
Standard hard disk drive

Frequency offset mode

Adds frequency-offset sweep and harmonic measurement capabilities.

Adds time domain transform, gating capabilities and graphical user

interface to simplify time domain measurements.
Enhanced time domain analysis
Time domain analysis
Measurement wizard assistant software

Rack mount kit

Adds time domain transform and gating capabilities.

Adds Measurement Wizard Assistant (MWA) software to simplify your

multiport measurements with the 4-port ENA

Adds a rack mount kit (part number: 1CM015A) for use without

handles.
Front handle kit
Rack mount and front handle kit

Adds a front handle kit (part number: 1CN005A).

Adds a rack mount and front handle kit (part number: 1CN009A).
Add keyboard
Add mouse

ISO 17025 compliant calibration
ANSI Z540 compliant calibration

5

1. Options are ordered using the combined model /option number, e.g. E5071C-240.

2. Order the 82357B USB/GPIB interface at the same time if you want to control power meters with the E5071C. This will allow you to conduct scalar mixer

calibrations (SMC), power calibrations, or receiver calibrations after power calibrations.

3. Option TDR is a superset of Option 010. Option TDR and Option 010 are mutually exclusive options and there is no need to purchase both options.

4. When using an ECal module with the MWA calibration wizard, a 4-port ECal module (i.e. N4431B, N4433A) is required.

5. Consider purchasing Keysight 20mm TORQUE WRENCH 8710-1764

05 | Keysight | E5071C Network Analyzer - Conguration Guide

SW6

6A 6B

6COM

SW7

7A 7B

7COM

SW8

8A 8B

8COM

SW9

9A 9B

9COM

SW10

10A10B

10COM

SW5

5A

5COM

5B

SW1

1A 1B

1C

1D

PORT 1

SW2

2A

2B 2C 2D

PORT 2

SW3

3A 3B 3C 3D

PORT 3

SW4

4A

4B 4C 4D

PORT 4

E5092A Congurable Multiport Test Set

This guide is intended to assist you in the ordering process of the
E5092A congurable multiport test set for use with the 4-port
ENA (E5070B, E5071B and E5071C). Multiple multiport measure­ment congurations, from 50 MHz to 20 GHz, can be made by
connecting included semi-rigid cables to the E5092A's front panel

which accesses its internal switches.

Step 1:1 Select appropriate cable and adapter set
for connection to the ENA (Optional)

E5092A-08C Cables and adapters for connection to
E5 071C Option 4 4 0 /4 45/460/465 /4 80/485
E5092A-20C Cables and adapters for connection to
E5071C Option 4D5/4K5

Step 2: Choose accessories (Optional)

E5092A-1CM Rack mount kit only
E5092A-1CN Front handle kit only
E5092A-1CP Rack mount kit with handle kit

Step 3: Choose calibration certication
documentation (Optional)

Documentation

The documentation for the E5092A is located in the
Online Help system for the E5071C ENA network analyzer. The
ENA Service Guide and Online Help system are also available on
the Web site:

www.keysight.com/nd/ena

Additional product information

For additional product information, refer to the ENA
brochure available on the Web site:

www.keysight.com/nd/ena
www.keysight.com/nd/multiport

E5092A-1A 7 ISO 17025 compliant calibration
E5092A-A6J ANSI Z540 compliant calibration

Step 4: Choose your warranty service
(Optional)

3 year return-to-Keysight warranty and service
5 year return-to-Keysight warranty and service

Block diagram

E5092A (Option 020)

1. Semi-rigid cables are designed for connection to the E5071C and are not available for the E5070B, E5071B.

06 | Keysight | E5071C Network Analyzer - Conguration Guide

E5092A Congurable Multiport Test Set

Options

To add options to a product, order the corresponding option number.

1

Option

Tes t set

Option 020 20 GHz switching test set Up to 22-port or 10-port full crossbar

Cable adapter set

Option 08C Cable and adapter set for

Option 20C Cable and adapter set for the E5071C

Accessories

Opt ion 1CM Rack mount kit Adds a rack mount kit (part number: 1CM015A) for use without

Opt ion 1CN Front handle kit Adds a front handle kit (part number: 1CN007A).

Opt ion 1CP Rack mount and front handle kit Adds a rack mount and front handle kit (part

Description Additional information

measurement.

Adds SMA semi-rigid cables and type-N-to-SMA adapters for
E5071C Option 440/445/460/465/480/485
(4.5 GHz/6.5 GHz/8.5 GHz)

Option 4D5/4K5 (14 GHz/20 GHz)

connection to the E5071C.

Adds SMA semi-rigid cables and 3.5 mm-to-3.5 mm adapters for

connection to the E5071C.

handles.

number: 1CP008A).

Calibration documentation

Option 1A7 ISO 17025 compliant calibration

Option A6J ANSI Z540 compliant calibration

1. Options are ordered using the combined model /option number, e.g. E5092A-020.

07 | Keysight | E5071C Network Analyzer - Conguration Guide

ENA Network Analyzer (E5071C)

Additional software options

Option TDR Enhanced time domain analysis

Option TDR enables the ENA to view reection and transmission
responses in the time domain using a simple and intuitive graphi­cal user interface. Use time domain to tune lters, gate out the
response of xtures and cables, characterize the impedance of
transmission lines, and more.

Option 010 Time domain analysis

Option 010 enables the ENA to view reection and transmission
responses in the time domain. Use time domain to tune lters,
gate out the response of xtures and cables, characterize the
impedance of transmission lines, and more.

Option 008 Frequency offset mode

Option 008 enables the ENA to set the receiver frequencies
independently from where the source frequency is tuned. This
ability is important for harmonic distortion measurements and
for measuring frequency converting devices such as mixers and
converters. Advanced calibration techniques for the ENA, such as
scalar mixer calibration (SMC) or vector mixer calibration (VMC),
require this option.

Option 1E5 High stability time base

Option 1E5 provides the following stability:
CW accuracy: ±1 ppm (specication)
Source stability: ±0.05 ppm (5 °C to 40 °C typical),
± 0.5 ppm/year

Hard disk drive options

2

Option 019 Standard hard disk drive

Option 019 provides a xed hard disk drive. The removable disk
drive is not available.

Option 017 Removable hard disk drive

Option 017 provides a removable hard disk drive. You can remove
or replace the hard disk drive for secure area operations. If a
spare disk is needed, order E5071CU-058 Solid state drive kit.

Option 790 Measurement Wizard Assistant

Option 790 provides a simple measurement procedure setup for
the 4-port ENA with a multiport test set such as the E5092A. The
software delivers an easy-to-use measurement wizard programs
including a calibration wizard setup1, which reduces operation
time for complicated, time-consuming multiport measurements.

Time base options

Option UNQ Standard stability time base

Option UNQ provides following stability:
CW accuracy: ±5 ppm (specication)
Source stability: ±5 ppm (5 °C to 40 °C typical)

Certication options

Option 1A7 ISO 17025 compliant calibration

Option 1A7 provides a complete set of measurements which test
the unit to manufacturer’s published specications. Includes cali­bration label, ISO 17025 calibration certicate, and data report,
and measurement uncertainties and guardbands on all customer
specications. Conforms to ISO 17025 and ISO 9001.

Option A6J ANSI Z540 compliant calibration

Option A6J provides a complete set of measurements which test
the unit to manufacturer’s published specications. Includes
pre- and post-adjustment data and measurement uncertainty
information compliant with the ANSI/NCSL Z540 standard.

1. When using an ECal module with MWA calibration wizard, a 4-por t ECal
module (i.e. N4431B, N4433A) is required.

2. A solid state drive is used as storage from Sep 2012.

08 | Keysight | E5071C Network Analyzer - Conguration Guide

Measurement Accessories

A complete list of RF and microwave test accessories
is available on our Web site: www.keysight.com/nd/accessories

Accessories are available with the following connector types:
50 Ω Type-N, 3.5 mm, 7 mm, 2.4 mm, 2.92 mm, 1.85 mm, 1.0 mm
and waveguide.

Test port cables and a calibration kit/ECal module should be
added for a complete measurement system.

Calibration kits

Coaxial measurements

Mechanical calibration kits include standards, such as opens,
shorts and loads, which are measured by the network analyzer for
increased measurement accuracy.

Electronic calibration (ECal) kits replace mechanical calibration
standards with one solid-state calibration module that is con­trolled by the network analyzer via USB. ECal kits provide many
different impedances to the test ports which enables a full two­port calibration to be performed quickly with a single connection.
This technique reduces operator errors and connector wear and

abrasion.

Choose a calibration kit for each connector type to be used.
Economy, includes:

Waveguide measurements

For waveguide measurements, Keysight offers mechanical cali­bration kits that include:

– waveguide-to-coax adapters (X, P, K, R, Q, U, and V bands)
– precision waveguide section
– ush short circuit
– xed terminations
– straight section

2

Cables and adapter sets

Keysight of fers the following types of cables:

– single cables: semi-rigid or exible
– cable sets: semi-rigid or exible

There are also adapter sets that protect the test port
and convert the port to the desired connector interface. These
kits contain:

– one male adapter
– one female adapter

To attain the best mechanical rigidity for device connection, use a
single cable and the appropriate special adapter set. To attain the
greatest exibility for device connection, use a cable set.

– open standards (male and female)
– short standards (male and female)
– xed-termination standards (male and female)

Standard, includes the devices in the economy kit and adds:

– sliding load standards1 (male and female) or a series of offset

shorts

Precision, includes the devices in the economy kit and adds:

– 50 Ω airline(s) for TRL calibration
– TRL adapters

1. A sliding load is not supported by the ENA.

2. An offset load is not supported by the ENA.

09 | Keysight | E5071C Network Analyzer - Conguration Guide

For devices with 50 Ω Type-N

connectors

Mechanical calibration kits

– 85032F economy: DC to 9 GHz. Includes:

85032-60017 Type-N (m) xed load
85032-60018 Type-N (f) xed load
85032-60013 Type-N (m) open
85032-60014 Type-N (f) open
85032-60016 Type-N (m) short
85032-60015 Type-N (f) short

– Option 85032F-100 adds:

85032-60021 Type-N (f) to Type-N (f) adapter

– Option 85032F-200 adds:

85032-60019 Type-N (m) to Type-N (m) adapter

– Option 85032F-300 adds:

85032-60020 Type-N (m) to Type-N (f) adapter

– Option 85032F-500 adds:

85054-60001 Type-N (f) to 7 mm adapter (two included)
85054-60009 Type-N (m) to 7 mm adapter (two included)

– 85054D economy: DC to 18 GHz. Includes:

85054-60025 Type-N (m) short
85054-60026 Type-N (f) short
85054-60027 Type-N (m) open
85054-60028 Type-N (f) open
85054-60031 Type-N (f) to 7 mm adapter
85054-60032 Type-N (m) to 7 mm adapter
85054-60037 Type-N (f) to Type-N (f) adapter
85054-60038 Type-N (m) to Type-N (m) adapter
85054-60046 Type-N (m) xed load
85054-60047 Type-N (f) xed load

Electronic calibration kits

– 85092C RF ECal: 300 kHz to 9 GHz, 2 por ts

Includes:
Option 85092C-MOF module with:
85092-60008 Type-N (f) to Type-N (m) RF ECal module
Option Option 85092C-00M module with:
85092-60009 Type-N (m) to Type-N (m) RF ECal module
Option 85092C-00F module with:
85092-60010 Type-N (f) to Type-N (f) RF ECal module
Option 85092C-00A adds:
85054-60037 Type-N (f) to Type-N (f) adapter
85054-60038 Type-N (m) to Type-N (m) adapter

– N4431B Microwave ECal: 9 kHz to 13.5 GHz, 4 ports1

Includes:
Option 020 module with:
N4431-60007 4 x Type-N (f) ECal module

N4431B-xxx mixed-connector options:

Connector type

3.5 mm (f) 101 201 301 401

3.5 mm (m) 102 202 302 402

Type-N 50 Ω (f) 103 203 303 403

Type-N 50 Ω (m) 104 204 304 404

7-16 (f ) 105 205 305 405

7-16 (m) 10 6 206 306 406

Port A
option

Port B
option

Port C
option

Port D
option

1. Performance from 9 kHz to 30 0 kHz is valid only for the E5071C ENA
network analyzer with rmware version A.09.10 or higher.

10 | Keysight | E5071C Network Analyzer - Conguration Guide

– N4432A Microwave ECal: 300 kHz to 18 GHz, 4 ports

Includes:
Option 020 module with:
N4432-60003 4 x Type-N (f) ECal module

N4432A-xxx mixed-connector options:

Connector type Port A

option

Port B
option

Port C
option

3.5 mm (f) 101 201 301 401

3.5 mm (m) 102 202 302 402

Type-N 50 Ω (f) 103 203 303 403

Type-N 50 Ω (m) 104 204 304 404

– N4690B Microwave ECal: 300 kHz to 18 GHz, 2 ports

Includes:
Option M0F module with:
N4690-60001 Type-N (f) to Type-N (m) ECal module
Option 00M module with:
N4690-60002 Type-N (m) to Type-N (m) ECal module
Option 00F module with:
N4690-60003 Type-N (f) to Type-N (f) ECal module
Option 00A adds:
85054-60037 Type-N (f) to Type-N (f) adapter
85054-60038 Type-N (m) to Type-N (m) adapter

Port D
option

Cables

– N6314A 50 Ω Type-N RF cable, DC to 12.4 GHz

Includes 8120-8862 one 610 mm (24 in) cable with male con­nectors

– N6315A 50 Ω Type-N RF cable, DC to 12.4 GHz

Includes 8121-0027 one 610 mm (24 in) cable with both
female and male connectors

Adapters

– 11853A 50 Ω Type-N accessory kit. Includes:

1250-1472 Type-N (f) to Type-N (f) adapter (two included)
1250-1475 Type-N (m) to Type-N (m) adapter (two included)
11511A Type-N (f) short
11512A Type-N (m) short

– 11878A Type-N to 3.5 mm adapter kit. Includes:

1250-1744 3.5 mm (f) to 50 Ω Type-N (m) adapter
1250-1743 3.5 mm (m) to 50 Ω Type-N (m) adapter
1250-1745 3.5 mm (f) to 50 Ω Type-N (f) adapter
1250-1750 3.5 mm (m) to 50 Ω Type-N (f) adapter

– 11524A 7 mm to Type-N (f) adapter
– 11525A 7 mm to Type-N (m) adapter
– 85130C

1,2 ,3

3.5 mm to Type-N Includes:
85054-60029 NMD-3.5 mm to Type-N (f)
85054-60030 NMD-3.5 mm to Type-N (m)

1. Special rugged female connector specically for connecting to the net­work analyzer test port, but does not mate with a standard
male connector.

2. Recommended to connect H device to E5071C option xD5/xK5 which has
NMD-3.5 mm (m) connectors.

3. Consider purchasing Keysight 20mm TORQUE WRENCH 8710-1764

11 | Keysight | E5071C Network Analyzer - Conguration Guide

For devices with 3.5 mm or SMA connectors

Mechanical calibration kits

– 85033E economy: DC to 9 GHz. Includes:

85033-60016 3.5 mm (m) load
85033-60017 3.5 mm (f) load
85033-60018 3.5 mm (m) open
85033-60019 3.5 mm (f) open
85033-60020 3.5 mm (m) short
85033-60021 3.5 mm (f) short
8710-1761 torque wrench
Option 85033E-100 adds:
85027-60005 3.5 mm (f) to 3.5 mm (f) adapter
Option 85033E-200 adds:
85027-60007 3.5 mm (m) to 3.5 mm (m) adapter
Option 85033E-300 adds:
85027-60006 3.5 mm (m) to 3.5 mm (f) adapter
Option 85033E-400 adds:
1250-1744 3.5 mm (f) to 50 Ω Type-N (m) adapter
1250-1743 3.5 mm (m) to 50 Ω Type-N (m) adapter
1250-1745 3.5 mm (f) to 50 Ω Type-N (f) adapter
1250-1750 3.5 mm (m) to 50 Ω Type-N (f) adapter
Option 85033E-500 adds:
1250-1746 3.5 mm (m) to 7 mm adapter (two included)
1250-1747 3.5 mm (f) to 7 mm adapter (two included)

– 85052C precision TRL: DC to 26.5 GHz. Includes:

00902-60003 3.5 mm (m) xed load
00902-60004 3.5 mm (f) xed load
85052-60006 3.5 mm (m) short
85052-60007 3.5 mm (f) short
85052-60008 3.5 mm (m) open
85052-60009 3.5 mm (f) open
85052-60032 3.5 mm (f) to 3.5 mm (f) adapter
85052-60033 3.5 mm (m) to 3.5 mm (m) adapter
85052-60034 3.5 mm (f) to 3.5 mm (m) adapter
85052-60035 3.5 mm short TRL line
85052-60036 3.5 mm long TRL line

Electronic calibration kits

– 85093C RF ECal: 300 kHz to 9 GHz, 2 ports

Standard module includes:
Option M0F with:
85093-60008 3.5 mm (f) to 3.5 mm (m) ECal module
Option 00F module with:
85093-60010 3.5 mm (f) to 3.5 mm (f) ECal module
Option 00M module with:
85093-60009 3.5 mm (m) to 3.5 mm (m) ECal module
Option 00A adds:
85052-60012 3.5 mm (f) to 3.5 mm (f) adapter
85052-60014 3.5 mm (m) to 3.5 mm (m) adapter

85093C-xxx mixed-connector options:

Port A option Port B option

Type (f) (m) Type (f) (m) Type (f) (m)

3.5 mm 101 102 Type-N 203 204 7-16 205 206

– N4431B Microwave ECal: 9 kHz to 13.5 GHz, 4 ports1

Includes:
Option 010 module with:
N4431-60006 4 x 3.5 mm (f) ECal module

N4431B-xxx mixed-connector options:

Connector
type

3.5 mm 201 301 401

3.5 mm (m) 102 202 302 402

Type-N
50 Ω (f)

Type-N
50 Ω (m)

7-16 (f ) 105 205 305 405

7-16 (m) 106 206 306 406

Port A
option

103 203 303 403

104 204 304 404

Port B
option

Port C
option

Port D
option

– 85052D economy: DC to 26.5 GHz. Includes:

00902-60003 3.5 mm (m) xed load
00902-60004 3.5 mm (f) xed load
85052-60006 3.5 mm (m) short
85052-60007 3.5 mm (f) short
85052-60008 3.5 mm (m) open
85052-60009 3.5 mm (f) open
85052-60012 3.5 mm (f) to 3.5 mm (f) adapter
85052-60013 3.5 mm (f) to 3.5 mm (m) adapter
85052-60014 3.5 mm (m) to 3.5 mm (m) adapter

1. Performance from 9 kHz to 30 0 kHz is valid only for the E5071C ENA
network analyzer with rmware version A.09.10 or higher.

– N4433A Microwave ECal: 300 kHz to 20 GHz, 4 ports

Includes:
Option 010 module with:
N4433-60003 4 x 3.5 mm (f) ECal module

12 | Keysight | E5071C Network Analyzer - Conguration Guide

N4433A-xxx mixed-connector options:

Connector
type

3.5 mm (f) 101 201 301 401

3.5 mm (m) 102 202 302 402

– N4691B Microwave ECal: 300 kHz to 26.5 GHz, 2 ports.

Includes:
Option M0F module with:
N4691-60001 3.5 mm (f) to 3.5 mm (m) ECal module
Option 00M module with:
N4691-60002 3.5 mm (m) to 3.5 mm (m) ECal module
Option 00F module with:
N4691-60003 3.5 mm (f) to 3.5 mm (f) ECal module
Option 00A adds:
85052-60012 3.5 mm (f) to 3.5 mm (f) adapter
85052-60014 3.5 mm (m) to 3.5 mm (m) adapter

Port A
option

Port B
option

Port C
option

Port D
option

Cables

– 1150 0 E

– 1150 0 F

– 85131C

– 85131D

– 85131-60010 one 3.5 mm (f) to PSC-3.5 mm (f), 53 cm,

– 85131E

– 85131F
– 85131-60012 one 3.5 mm (f) to 3.5 mm (m), 62.2 cm,

– 85131-60013 one 3.5 mm (f) to PSC-3.5 mm (f), 62.2 cm,

– 85131G

– 85131H

– 85134C1 single, semi-rigid: PSC-3.5 mm (f) to 2.4 mm (f),

2, 3, 4

cable, APC 3.5 mm (m), DC to 26.5 GHz

Includes: one 610 mm (24 in) with male connectors.

2, 3, 4

150 cm cable, APC 3.5 mm (m), DC to 26.5 GHz

Includes: one 1520 mm (60 in) with male connectors.

1, 4

single, semi-rigid:

3.5 mm (f) to PSC-3.5 mm (f), 81 cm, 32 inches

1. 4

set, semi-rigid:
85131-60009 one 3.5 mm (f) to 3.5 mm (m), 53 cm,
21 inches,

21 inches

1, 4

single, exible: 3.5 mm (f) to PSC-3.5 mm (f),

96.5 cm, 38 inches

1, 4

set, exible:

24.5 inches

24.5 inches

1, 4

single, semi-rigid: 3.5 mm (f) to 3.5 mm (m),
53 cm, 21 inches

1, 4

single, exible: 3.5 mm (f) to 3.5 mm (m), 62.2 cm,

24.5 inches

81 cm, 32 inches

– 85134D1 set, semi-rigid:
– 85134-60002 one 2.4 mm (f) to PSC-3.5 mm (f), 53 cm,

21 inches

– 85134-60001 one 2.4 mm (f) to PSC-3.5 mm (m), 53 cm,

21 inches

– 85134E1 single, exible: PSC-3.5 mm (f) to 2.4 mm (f),

96 cm, 38 inches

– 85134F1 set, exible:

85134-60004 one 2.4 mm (f) to PSC-3.5 mm (f), 61 cm,

24 inches

85134-60003 one 2.4 mm (f) to PSC-3.5 mm (m), 61 cm,

24 inches

– 85134G1 single, semi-rigid: 2.4 mm (f) to PSC-3.5 mm (m),

53 cm, 21 inches

– 85134H1 single, exible: 2.4 mm (f) to PSC-3.5 mm (m),

61 cm, 24 inches

– N4419AK20 single, exible: 3.5 mm (m) to 3.5 mm (f),

91.4 cm, 36 inches

– Z5623A-K20 single, exible: 3.5 mm (m) to 3.5 mm (m),

91.4 cm, 36 inches

Adapters

– 11853A 50 Ω Type-N accessory kit.

Includes:
1250-1472 Type-N (f) to Type-N (f) adapter (two included)
1250-1475 Type-N (m) to Type-N (m) adapter (two included)
85032-60009 Type-N (f) short
85032-60008 Type-N (m) short

– 11878A Type-N to 3.5 mm adapter kit.

Includes:
1250-1744 3.5 mm (f) to 50 Ω Type-N (m) adapter
1250-1743 3.5 mm (m) to 50 Ω Type-N (m) adapter
1250-1745 3.5 mm (f) to 50 Ω Type-N (f) adapter
1250-1750 3.5 mm (m) to 50 Ω Type-N (f) adapter

– 11524A 7 mm to Type-N (f) adapter
– 11525A 7 mm to Type-N (m) adapter
– 85130C1 3.5 mm to Type-N

Includes:
85054-60029 NMD-3.5 mm to Type-N (f)
85054-60030 NMD-3.5 mm to Type-N (m)

– 85130D1 3.5 mm to 3.5 mm

Includes:
85130-60005 NMD-3.5 mm to PSC-3.5 mm (f)
85130-60006 NMD-3.5 mm to PSC-3.5 mm (m)

– 85130F1 2.4 mm to 3.5 mm

1. Special rugged female connector specically for connecting to the
network analyzer test por t, but does not mate with a standard male con­nector.

2. 1250-1744 3.5 mm (f) to 50 Ω Type-N (m) adapters are recommended to

connect to the E5071C Option x4x, x6x, and x8x test ports, which have
Type-N (f) connectors.

3. NMD-3.5 mm (f ) to 3.5 mm (f), or 3.5 mm (f) to 3.5 mm (f) adapters are
recommended to connect to the E5071C Option xD5, xK5, which have
NMD-3.5 mm (m) connectors.

4. Consider purchasing Keysight 20mm TORQUE WRENCH 8710-1764

13 | Keysight | E5071C Network Analyzer - Conguration Guide

For devices with 75 Ω Type-N connectors

Mechanical calibration kits

– 85036B DC to 3 GHz, includes:

00909-60019 75 Ω Type-N (m) broadband load
00909-60020 75 Ω Type-N (f) broadband load
85036-60012 75 Ω Type-N (m) short
85036-60011 75 Ω Type-N (f) short
85032-60007 75 Ω Type-N (m) open
85032-20001 75 Ω Type-N (f) open body
85036-60010 75 Ω Type-N (f) open center conductor
extender
85036-60013 75 Ω Type-N (m) to (m) adapter
85036-60014 75 Ω Type-N (f) to (f) adapter
85036-60015 75 Ω Type-N (m) to (f) adapter

– 85036E DC to 3 GHz, includes:

00909-60019 75 Ω Type-N (m) broadband load
85036-60016 75 Ω Type N (m) combined open/short

Adapters

– 11852B Minimum-loss pad

Option 11852B-004 Type-N connectors, 50 Ω (m) to 75 Ω (f)

Calibration must be done with a 75 Ω calibration kit
using an 11852B minimum-loss pad, and impedance conversion
to 75 Ω using the ENA’s xture simulator function is required.

For devices with waveguide

Mechanical calibration kits

X Band

– X11644A standard, WR-90: 8.2 to 12.4 GHz.

Includes:
00896-60008 X-band standard section
00910-60003 X-band termination
11644-20018 X-band short
11644-20021 X-band shim

– 85132F cable set (set of 2, exible 7 mm to 3.5 mm, 62.9 cm

each, 24.75 inches each)

– 85135F cable set (set of 2 , exible, 7 mm to 2.4 mm, 53 cm

each, 21 inches each)

– X281C adapter (included in calibration kit): WR-90 to 7 mm

P Band

– P11644A standard, WR-62: 12.4 to 18 GHz.

Includes:
00896-60007 P-band standard section
00910-60002 P-band termination
11644-20017 P-band short
11644-20020 P-band shim

– 85132F cable set (set of 2, exible, 7 mm to 3.5 mm, 62.9 cm

each, 24.75 inches each)

– 85135F cable set (set of 2, exible, 7 mm to 2.4 mm, 53 cm

each, 21 inches each)

– P281C adapter (included in calibration kit): WR-62 to 7 mm

K Band

– K11644A standard, WR-42: 18 to 26.5 GHz.

Includes:
00896-60006 K-band standard section
00910-60001 K-band termination
11644-20016 K-band short
11644-20019 K-band shim

– 85134F cable set (set of 2, exible, 3.5 mm to 2.4 mm, 53 cm

each, 21 inches each)

– K281C adapter (included in calibration kit):

WR-42 to 3.5 mm (f)
Option 0121 WR-42 to 3.5 mm (m)

1. For this option order K281C-012.

14 | Keysight | E5071C Network Analyzer - Conguration Guide

Additional Accessories

Power limiters

– N9355B power limiter, 10 dBm limiting threshold,

10 MHz to 18 GHz, Type-N

– N9356B power limiter, 25 dBm limiting threshold,

10 MHz to 18 GHz, Type-N

– N9355C power limiter, 10 dBm limiting threshold,

10 MHz to 26.5 GHz, 3.5 mm

– N9356C power limiter, 25 dBm limiting threshold,

10 MHz to 26.5 GHz, 3.5 mm

DC blocks

– N9398C DC block, 16 V maximum working voltage,

50 kHz to 26.5 GHz, 3.5 mm

– N9399C DC block, 50 V maximum working voltage,

700 kHz to 26.5 GHz, 3.5 mm

– 11742A, 50 V maximum working voltage, 45 MHz to 26.5 GHz,

3.5 mm

Ampliers

– 87405B pre-amplier, 22 dB gain, 10 MHz to 4 GHz
– 87405C pre-amplier, 25 dB gain, 100 MHz to 18 GHz
– 87415A amplier, 25 dB gain, 2 to 8 GHz
– 83006A amplier, 20 dB gain, 10 MHz to 26.5 GHz

Attenuators

– 8491A xed attenuator, DC to 12.4 GHz, Type-N
– 8493A xed attenuator, DC to 12.4 GHz, SMA

RF & microwave switches

Power meters and sensors1

Recommended for source output power calibration.

– E4 416A1 single-channel EPM-P series power meter
– E4 417A1 dual-channel EPM-P series power meter
– E4 418B1 single-channel EPM series power meter
– E4 419B1 dual-channel EPM series power meter
– N1911A1 single-channel P-series power meter
– N1912A1 dual-channel P-series power meter
– 8482A power sensor, 100 kHz to 4.2 GHz, Type-N (m), 100 mW
– E9304A-H18 power sensor, 9 kHz to 18 GHz, Type-N (m), 100 mW
– E4412A CW power sensor, 10 MHz to 18 GHz, Type-N (m), 200 mW
– E4413A CW power sensor, 50 MHz to 26.5 GHz, 3.5 mm (m), 200 mW
– N1921A power sensor 50 MHz to 18 GHz, Type-N (m)
– N1922A power sensor 50 MHz to 40 GHz, 2.4 mm (m)
– U2000A/B/H2 USB power sensor, 10 MHz to 18 GHz, Type-N (m)
– U2001A/B/H2 USB power sensor, 10 MHz to 6 GHz, Type-N (m)
– U2002A/H2 USB power sensor, 50 MHz to 24 GHz, 3.5 mm (m)
– U2004A2 USB power sensor, 9 kHz to 6 GHz, Type-N (m)

Probes

– N1021B 18 GHz differential TDR/TDT passive probe kit
– 85024A high-frequency probe, 300 kHz to 3 GHz

General accessories

System racks

– 1CN005A handle kit, may be ordered as option 1CN (two included)
– 1CM015A rack mount kit, for use without handles: may be ordered as

option 1CM

– 1CP009A rack mount kit, for use with previously supplied handles;

may be ordered as option 1CP

– E3663AC rack mount rail kit, for use with 1CM015A or 5188-4430
– 1181BZ test mobile system cart

– N1810TL SPDT switch, terminated, DC to 26.5 GHz
– N1810UL SPDT switch, unterminated, DC to 26.5 GHz
– 87104B SP4T switch, terminated, DC to 20 GHz
– 87106B SP6T switch, terminated, DC to 20 GHz
– 87222C transfer switch, DC to 26.5 GHz
– L7104B SP4T switch, terminated, DC to 20 GHz
– L7106B SP6T Switch, terminated, DC to 20 GHz
– L7222C transfer switch, DC to 26.5 GHz
– P9400C solid state PIN diode transfer switch, 100 MHz to 18 GHz
– P9402C SPDT solid state PIN diode switch, 100 MHz to 18 GHz
– P9404C SP4T solid state PIN diode switch, 100 MHz to 18 GHz
– U9397C SPDT solid state FET hybrid switch, 300 kHz to 18 GHz
– U9400C solid state FET hybrid transfer switch, 300 KHz to 18 GHz

1. Order the 82357B USB/GPIB interface to control a power meter by the
E5 07 1C.

2. To use the U200x USB power sensors for source power calibration, the

E5071C ENA rmware version A.09.2x or higher is required.

Interface cables

The following GPIB cables can be used to connect the network
analyzer with an external device such as a computer

– 10833A GPIB cable, 1.0 m (3.3 ft)
– 10833B GPIB cable, 2.0 m (6.6 f t)
– 10833C GPIB cable, 4.0 m (13.1 ft)
– 10833D GPIB cable, 0.5 m (1.6 ft)
– 82357B GPIB to USB interface, necessary to control a power meter or

signal generator with the E5071C.

Monitors

– XGA-compatible monitor

Printers

– USB printers with Microsoft Windows printer driver

Other

– 8710-1764 WRENCH - TORQUE 8 IN/LB, 20 MM OPEN END

15 | Keysight | E5071C Network Analyzer - Conguration Guide

Upgrade kits

Upgrade kits for the E5071C

Protecting your hardware investment

The E5071C ENA network analyzer is a safe investment because
of its flexibility. Easily upgrade any ENA software or hardware
feature whenever you need that feature.

Ordering instructions

To upgrade an existing E5071C, order the corresponding upgrade
kit model. For further information, visit:

http://www.keysight.com/find/ena_upgrades

Application and product notes

Introduction to the Fixture Simulator Function of the ENA Series
RF Network Analyzers: Network De-embedding/Embedding and
Balanced Measurement, Product Note E5070/71-1 Literature

number 5988-4923EN

Evolution of Test Automation Using Built-in VBA with the ENA
Series RF Network Analyzers, Product Note E5070/71-2

Literature number 5988-6192EN

On-wafer Multiport Calibration Using the ENA Series RF Network
Analyzer with the Cascade Microtech Probing System, Product

Note E5070/71-3

Literature number 5988-5886EN

In-Fixture Characterization Using the ENA Series RF Network
Analyzer with Cascade Microtech Probing System, Product Note

E5 070/71-4

Literature number 5988-6522EN

Improve the Circuit Evaluation Efciency of Wireless LAN

Chip Set Design, Application Note 1463-2
Literature number 5988-9803EN

Impedance Characteristic Evaluation of SMD by Using the ENA
with Inter-Continental Microwave (ICM)

Application Note 1463-5
Literature number 5989-0547EN

Accurate Mixer Measurements Using the Frequency-Offset
Mode, Application Note 1463-6

Literature number 5989-1420EN

7 Reasons to Migrate from Your 8753 to an ENA Network Ana­lyzer Application Note 1478

Literature number 5989-0206EN

Multiport Solutions for E5071C ENA RF Network Analyzers Using
External Switches

Literature number 5989-7916EN

Advanced Measurement Techniques for RF Ampliers Using

Unique Functions of the Keysight E5071C ENA

Literature number 5989-6522EN

Measurement Wizard Assistant software for ENA/E5091A

Literature number 5989-4855EN

Comprehensive Multiport Solution for the ENA
Network Analyzer

Literature number 5989-8737EN

E5071C ENA Option TDR Enhanced Time Domain
Analysis Option

Literature number 5990-5237EN

Correlation between TDR oscilloscope and VNA generated time
domain waveform

Literature number 5990-5238EN

Literature and information

ENA Network Analyzers Brochure

Literature number 5989-5478EN

ENA Network Analyzers Data Sheet

Literature number 5989-5479EN

Keysight Network Analyzer Selection Guide

Literature number 5989-7603EN

ENA-L RF Network Analyzers Brochure

Literature number 5989-0167EN

ENA-L RF Network Analyzers Data Sheet

Literature number 5989-0018EN

Test Solutions for Multiport and Balanced Devices
Selection Guide

Literature number 5988-2461EN

Keysight RF & MW Test Accessories Catalog

Literature number 5968-4314EN

Key web resources for additional infor­mation on the ENA Series, visit:

www.keysight.com/find/ena

16 | Keysight | E5071C Network Analyzer - Conguration Guide

myKeysight

www.keysight.com/find/mykeysight

A personalized view into the information most relevant to you.

www.axiestandard.org

AdvancedTCA® Extensions for Instrumentation and Test (AXIe) is an
open standard that extends the AdvancedTCA for general purpose and
semiconductor test. Keysight is a founding member of the AXIe consortium.

ATCA®, AdvancedTCA®, and the ATCA logo are registered US trademarks of

the PCI Industrial Computer Manufacturers Group.

www.lxistandard.org

LAN eXtensions for Instruments puts the power of Ethernet and the
Web inside your test systems. Keysight is a founding member of the LXI
consortium.

www.pxisa.org

PCI eXtensions for Instrumentation (PXI) modular instrumentation delivers a
rugged, PC-based high-performance measurement and automation system.

Three-Year Warranty

www.keysight.com/find/ThreeYearWarranty

Keysight’s commitment to superior product quality and lower total cost
of ownership. The only test and measurement company with three-year
warranty standard on all instruments, worldwide.

Keysight Assurance Plans
www.keysight.com/find/AssurancePlans

Up to five years of protection and no budgetary surprises to ensure your
instruments are operating to specification so you can rely on accurate
measurements.

www.keysight.com/go/quality

Keysight Technologies, Inc.
DEKRA Certified ISO 9001:2008
Quality Management System

Keysight Channel Partners
www.keysight.com/find/channelpartners

Get the best of both worlds: Keysight’s measurement expertise and product
breadth, combined with channel partner convenience.

For more information on Keysight
Technologies’ products, applications or
services, please contact your local Keysight
office. The complete list is available at:
www.keysight.com/find/contactus

Americas

Canada [phone]
Brazil 55 11 3351 7010
Mexico 001 800 254 2440
United States [phone]

Asia Pacic

Australia 1 800 629 485

China 800 810 0189
Hong Kong 800 938 693

India 1 800 11 2626
Japan 0120 (421) 345

Korea 080 769 0800

Malaysia 1 800 888 848
Singapore 1 800 375 8100

Taiwan 0800 047 866

Other AP Countries (65) 6375 8100

Europe & Middle East

Austria 0800 001122
Belgium 0800 58580
Finland 0800 523252
France 0805 980333
Germany 0800 6270999
Ireland 1800 832700
Israel 1 809 343051
Italy 800 599100
Luxembourg [phone]
Netherlands 0800 0233200
Russia 8800 5009286
Spain 800 000154
Sweden 0200 882255
Switzerland 0800 805353

Opt. 1 (DE)
Opt. 2 (FR)
Opt. 3 (IT)

United Kingdom 0800 0260637

For other unlisted countries:
www.keysight.com/find/contactus

(BP-02-20-15)

This information is subject to change without notice.
© Keysight Technologies, 2013 - 2015
Published in USA, March 25, 2015

5989-5480EN

www.keysight.com