E4982A LCR Meter
1 MHz to 300 MHz/500 MHz/1 GHz/3 GHz
Find us at www.keysight.com Page 1
Ordering guide
Standard furnished item
Description
Additional information
Test head with 1m test cable
See accessory option for cable extension
Installation guide
Power cable
Certification of calibration
1 MHz – 300 MHz
E4982A-030
1 MHz – 500 MHz
E4982A-050
1 MHz - 1 GHz
E4982A-100
1 MHz - 3 GHz
E4982A-300
Required when performing calibration at DUT
0.5 mm, 1.6 x 0.8 mm, 2.0 x 1.2 mm, 3.2 x 1.6 mm)
Coaxial cable set for extending the test head
head cables are needed for installation.
Recommended for system calibration and
case.
The following steps will guide you through configuring your E4982A.
Note: The following are not furnished: Calibration kit, Test Fixture Stand, 3.5 mm-to-7 mm Adapter, Keyboard
and Mouse. Refer to Accessory Option and Available Accessories for the selection of these items.
Step 1. Choose frequency option (mandatory)
Description Option no. Requires Not compatible Additional information
Step 2. Choose accessory option for integrating into component handler system (If not required, go to Step 3.)
Description Option no. Requires Not compatible Additional information
Working standard set E4982A-004 None None
Test head extension cable s et E4982A-020 None None
16195B calibration kit E4982A-700 E4982A-710, -720 None
contacts of component handler or test fixture. Includes
Shorting Bars and 51.0 Ω Chip Resistors (SMD size: 1.0 x
cable to 2 m from standard 1 m. Required when 2 m test
tests. Usable for multiple E4982As. Required to
perform calibration at 7 mm connector plane of
3.5 mm-to-7 mm adapter attached to 3.5 mm test port
connector on test head. Includes OPEN, SHORT, 50 Ω
LOAD, LOW-LOSS CAPACITOR standards and carrying
Note: Refer to Upgrade for retrofit information on the above options.
Find us at www.keysight.com Page 2
Step 3. Choose accessory option for using test fixture (if not required, go to Step 4.)
Needed when performing calibration at DUT contacts of
1.2 mm, 3.2 x 1.6 mm).
Coaxial cable set for extending the test head cable to 2 m
are needed for installation.
Required for performing calibration at 7 mm connector
carrying case. Usable for multiple E4982As.
Required for using Keysight’s RF component test fixtures
in this guide.
Required for using Keysight’s RF component test fixtures
in this guide.
USB Keyboard for simplifying measurement setup and
programming.
None
None
USB Mouse for simplifying measurement setup and
programming.
Rackmount kit
E4982A-1CM
None
None
Not installable simultaneously with E4982A-1CP.
Front handle kit
E4982A-1CN
None
None
Not installable simultaneously with E4982A-1CP.
Handle/rack mount kit
E4982A-1CP
None
None
Not installable simultaneously with E4982A-1CM or 1CN.
Option 019 is the only data storage option for the
E4982A. Must choose this option.
Description Option no. Requires Not compatible Additional information
custom fixture or component handler. (Not required when
Working standard set E4982A-004 None None
using the Keysight Technologies, Inc. RF component test
fixtures). Includes Shorting Bars and 51.0 Ω Chip
Resistors (SMD size: 1.0 x 0.5 mm, 1.6 x 0.8 mm, 2.0 x
Test head extension cable s et E4982A-020 None None
16195B calibration kit E4982A-700 E4982A-710, -720 None
Test fixture stand E4982A-710 E4982A-700, -720 None
3.5 mm-to-7 mm
coaxial adapter
E4982A-720 E4982A-700, -710 None
from standard 1 m. Required when 2 m test head cables
plane of 3.5 mm-to-7 mm adapter attached to 3.5 mm test
port connector on test head. Includes OPEN, SHORT, 50
Ω LOAD, LOW-LOSS CAPACITOR standards and
and the 16195B calibration kit. See Available Accessories
and the 16195B calibration kit. See Available Accessories
Note: Refer to Upgrade for retrofit information on the above options.
Step 4. Choose general/miscellaneous accessory option (If not required, go to Step 5.)
Description Option no. Requires Not compatible Additional information
Keyboard E4982A-810 None None
Mouse E4982A-820
Note: Refer to Upgrade for retrofit information on the above options.
Step 5. Choose data storage
Description Option no. Requires Not compatible Additional information
Standard data storage E4982A-019 None None
Find us at www.keysight.com Page 3
Step 6. Choose calibration certificate option
ISO 17025 compliant calibration
E4982A-1A7
ISO 17025 compliant calibration
ANSI Z540 compliant calibration
E4982A-A6J
ANSI Z540 compliant calibration
Requires
E4982A-004
Working standard set
E4982AU-004
Yes
None
None
E4982A-020
Test fixture extension cable set
E4982AU-020
No
None
None
E4982A-100
Test fixture extension cable set
E4982AU-101
No
E4982A-050
E4982A-100
Upgrade from 300 MHz to 1 GHz
E4982AU-100
No
E4982A-030
E4982A-300
Upgrade from 1 GHz to 3 GHz
E4982AU-302
No
E4982A-100
E4982A-300
Upgrade from 500 MHz to 3 GHz
E4982AU-301
No
E4982A-050
E4982A-300
Upgrade from 300 MHz to 3 GHz
E4982AU-300
No
E4982A-030
E4982A-050
Upgrade from 300 MHz to 500 MH
E4982AU-050
No
E4982A-030
E4982A-700
16195 calibration kit
16195B
Yes
4982A-710, -720
None E4982A-710
Test fixture stand
04287-60121
Yes
E4982A-720
None E4982A-720
3.5 mm-to-7 mm adapter
1250-1746
Yes
None
None E4982A-810
Keyboard
5188-4463
Yes
None
None E4982A-820
Mouse
1150-7799
Yes
None
None E4982A-1CM
Rackmount kit
5063-9216
Yes
None
None
E4982A-1CN
Front handle kit
5063-9229
Yes
None
None E4982A-1CP
Handle/rack mount kit
5188-4430
Yes
None
None
Upgrade OS, from Windows XP to 7,
for E4982A
E4982AU-040
None
Upgrade OS, from Windows XP/7 to
Windows 10, for E4982A
E4982AU-041
None
Description Option no. Additional information
Hardware Upgrades
Option no. Description
Upgrade Model no.
or equivalent part
number
Customer
installable
(Instrument must
already include
the following)
Not
compatible
Additional
information
Installable at
service center only
N/A
N/A
Note: For firmware update and upgrade information, refer to product homepage on the Keysight home
website.
Find us at www.keysight.com Page 4
No Windows XP
No Windows XP/7
Available Accessories – Measurement Accessories
Requires (Instrument must
16196A
E4982A-700, -710, -720
For 1608 (mm)/0603 (inch) SMD up to 3 GHz
16196A-710
–
Add magnifying lens and tweezers
16196A-ABA
–
U.S. – English localization
16196A-ABJ
–
Japan – Japanese localization
16196B
E4982A-700, -710, -720
For 1005 (mm)/0402 (inch) SMD up to 3 GHz
16196B-710
–
Add magnifying lens and tweezers
16196B-ABA
–
U.S. – English localization
16196B-ABJ
–
Japan – Japanese localization
16196C
E4982A-700, -710, -720
For 0603 (mm)/0201 (inch) SMD up to 3 GHz
16196C-710
–
Add magnifying lens and tweezers
16196C-ABA
–
U.S. – English localization
16196C-ABJ
–
Japan – Japanese localization
16196D
E4982A-700, -710, -720
For 0402 (mm)/01005 (inch) SMD up to 3 GHz
16196D-710
–
Add magnifying lens and tweezers
16196D-ABA
–
U.S. – English localization
16196D-ABJ
–
Japan – Japanese localization
High
test fixture
For SMD and leaded device up to 2 GHz, Temperature range: –55 ºC to +200 ºC.
Manual are furnished.
16194A-010
–
Add EIA, EIAJ size shorting bar set
16194A-701
–
Add Shorting bar set; (1 x 1 x 2.4, 1.6 x 2.4 x 2, 3.2 x 2.4 x 2.4, 4.5 x 2.4 x 2.4) mm
For SMD from 1005 (mm)/0402 (inch) to 3225 (mm)/1210 (inch); up to 3 GHz.
carrying case and, Operation and Service Manual are furnished.
16197A-001
–
Add 0603 (mm)/0201 (inch) device guide
16197A-ABA
–
U.S. – English localization
16197A-ABJ
–
Japan – Japanese localization
SMD test
fixture
16192A
E4982A-700, -710, -720
For SMD up to 2 GHz. Operation and Service Manual is furnished.
16192A-010
–
Add EIA/EIAJ size shorting bar set.
16192A-701
–
Add Shorting bar set; (1 x 1 x 2.4, 1.6 x 2.4 x 2, 3.2 x 2.4 x 2.4, 4.5 x 2.4 x 2.4) mm
16192A-710
–
Add magnifying lens and tweezers
DC bias
adapter
External DC bias adapter; 5 A max. or 40 V max., 1 MHz to 1 GHz.
Operation and Service Manual is furnished.
Add shorting bars and 51 Ω working standard resistors set: from 0603 (mm) /0201
(inch) to 3216 (mm)/1206 (inch)
Description Model no.
Parallel
electrode
SMD test
fixture
Parallel
electrode
SMD test
fixture
Parallel
electrode
SMD test
fixture
Parallel
electrode
SMD test
fixture
already include the following)
Additional information
temperature
Bottom
electrode
SMD test
fixture
Parallel
electrode
SMD test
fixture
16200B-001 –
16194A E4982A-700, -710, -720
16197A E4982A-700, -710, -720
16092A E4982A-700, -710, -720 For SMD and leaded device up to 500 MHz. Operation note is furnished.
16200B E4982A-700, -710, -720
50 Ω working standard resistors, wrench, tweezers and, Operation and Service
Device guides, EIA/EIAJ size shorting bar set, tweezers, wrench, magnifying lens,
Note: For more detailed information, refer to Accessories Selection Guide for Impedance Measurements.
Find us at www.keysight.com Page 5
This inform ation is subj ect to chang e without no tice. © Key sight Technol ogies, 2012 - 2021, Published in USA, June 8, 2021, 5990-991 2EN
Learn more at: www.keysight.com
Requires (Instrument must
Performance
Test Kit
7 mm performance test kit; includes Open, Short, 50 Ω Load, Air-line, calibration
data, wrench and carrying case.
5990-9882EN
E4982A Data Sheet
5990-9911EN
E4982A Brochure
5952-1430E
LCR Meters, Impedance Analyzers and Test Fixtures Selection Guide
5965-4792E
Accessories Selection Guide For Impedance Measurements
5950-3000
Impedance Measurement Handbook
Available Accessories – for Performance Test and Maintenance
Description Model no.
16190B –
already include the following)
Additional information
Note: For details of the performance test kit, refer to product homepage on the Keysight home website.
Literature Resources
Literature number Description
More literature is available on our web site.
Web Resources
Get the latest news, product and support information, application literature and more.
http://www.keysight.com/find/lcrmeters
For more information on Keysight Technologies’ products, applications or services,
please contact your local Keysight office. The complete list is available at:
www.keysight.com/find/contactus
Find us at www.keysight.com Page 6
Loading...