Keys Fitness HT-760T User Manual
Owner’s Manual
HealthTrainer
HT-760T Treadmill
Customer Service
(888) 340-0482
Keys Fitness Products
4009 Distribution Drive
Suite 250
Garland, TX 75041
www.keysfitness.com
CAUTION! Read all precautions
and instructions in this manual
before using this equipment.
Model Name : HT-760T
Serial Number :
415-00177
09/07 Rev
Write down for future reference
Serial Number Decal Location
Table of Contents
Important Safety Information 3
Before You Start 4
Assembly 5
Parts Identifier 5
Assembly Steps 6
Moving Instructions 10
Power Requirements 11
Console Instructions 12
Overview 12
Program Operation 13
Program Profiles 16
Monitoring Your Heart Rate 18
Workout Information 20
Frequency: How Often Should You Exercise 20
Intensity: How Hard Should You Exercise 20
Weight Management 20
Exercise Practice Procedures 21
Workout: Brisk and Rhythmic Exercise 21
Cool Down: Slow and Relaxed Exercise 21
Exercise Guidelines 22
Calibration Sequence 25
Change to MPH or KPH 25
Belt Adjustment 26
Maintenance Instructions 27
Error Messages 28
Troubleshooting Guide 29
Parts List 30
Exploded View 31
Warranty 32
2
Important Safety Information
WARNING! Before using this treadmill or starting any exercise program, consult your
physician. This is especially important for persons over the age of 35 and/or persons with
pre-existing health problems. The manufacturer or distributor assumes no responsibility for
personal injury or property damage sustained by or through the use of this product.
WARNING! To reduce the risk of electrical shock, burns, fire, or other possible injuries to the
user, it is important to review this manual and the following precautions before operation.
SAVE THESE INSTRUCTIONS
SAFETY PRECAUTIONS AND TIPS
1. Always secure Safety Key firmly to waistband.
2. It is the owner’s responsibility to ensure that all users of this treadmill have read the
Owner’s Manual and are familiar with warnings and safety precautions.
3. This treadmill has a user maximum capacity of 325 pounds.
4. The treadmill should only be used on a level surface and is intended for indoor use only.
The treadmill should not be placed in a garage, patio, or near water and should never be
used while you are wet. Keys Fitness recommends a treadmill mat be placed under the
treadmill to protect floor or carpet and for easier cleaning.
5. Follow safety information in regard to plugging in your treadmill. Keep the power cord away
from the incline wheels and do not run the power cord underneath your treadmill. Do not
operate the treadmill with a damaged or frayed power cord.
6. Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not
use the treadmill with bare feet, sandals, socks or stockings.
7. Always straddle the belt and allow it to start moving before stepping onto the belt.
8. Hold on to handlebar when adjusting speed or other controls.
9. Always examine your treadmill before using to ensure all parts are in working order.
10. Allow the belt to fully stop before dismounting.
11. Pets should never be allowed near or on the treadmill.
12. Close supervision is necessary when this appliance is used by or near children, invalids or
disabled persons.
13. Never operate the treadmill where oxygen is being administered, or where aerosol products
are being used.
14. Never insert any object or body parts into any opening.
15. For safety and to prevent damage to your treadmill, no more than one person should use
the treadmill at a time.
16. Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill
should only be performed by an authorized service representative, unless authorized and/or
instructed by the manufacturer
17. Failure to follow these instructions will void the treadmill warranty.
18. Never leave the treadmill unattended when plugged in. Unplug from outlet when not in use
and before service or maintenance.
19. Always unplug this appliance immediately after using and before cleaning. To disconnect,
turn all controls to the off position, then remove plug from outlet.
3
Before You Start
Thank you for purchasing the Healthtrainer HT-760T Treadmill! This quality product you
have chosen was designed to meet your needs for cardiovascular exercise. Before you start,
please read the Owner's Manual and become familiar with the operation of your new treadmill.
Remember to take the time to perform the stretching exercises provided to avoid
injury.
Do not stand on the walking belt while pressing the Power button or Start/Stop button.
Always adjust the speed of the treadmill in small increments as this treadmill is capable of
high speeds.
If you are taking medication, consult your physician to see if the medication will affect your
exercise heart rate.
If you have heart problems, you are not active, and/or are over the age of 35 years, do not
use the pre-set treadmill programs or start an exercise program without first contacting and
receiving approval from your physician.
To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids on the
console. Keys Fitness recommends a sealed water bottle for beverages consumed while using
the treadmill.
Please review the following drawing below to familiarize yourself with the listed
parts. This manual covers several treadmills, so the one pictured below may not be
identical to your particular model.
INCLINE SWITCH
MOTOR COVER
CONSOLE
LEFT UPRIGHT
SPEED SWITCH
RUNNING BELT
LEVELER
RIGHT UPRIGHT
4
Assembly: Parts Identifier
U4T1
U4T4
U4T5
U4D1
UAS29
UAS30
U4J24
U4J5
U4J27
UAW8 UAW9 UAW10
U4J28
U4J7
UAT6
UAT7
U4T11
U4J4
Ref # Description Qty Ref # Description Qty
U4T1 MAIN FRAME 1 U4J24 SCREW ST4.2*12 6
U4T4 LEFT UPRIGHT 1 U4J5 BOLT M10*25 12
U4T5 RIGHT UPRIGHT 1 UAJ7 BOLT M8x50 4
U4D1 CONSOLE 1 U4J28 FLAT WASHER 8 6
UAS29 LEFT PROTECTION COVER 1 U4J27 FLAT WASHER 10 12
UAS30 RIGHT PROTECTION COVER 1 UAW8 #6 ALLEN WRENCH 1
UAT6 LEFT HANDLEBAR 1 UAW9 #5 ALLEN WRENCH 1
UAT7 RIGHT HANDLEBAR 1 UAW10 WRENCH W/SCREW DRIVER 1
U4T11 CROSS BAR 1
The Healthtrainer HT-760T Treadmill will require assembly before operating. Place
unopened box on a clean, level surface. After opening the box, remove any packing material
from the treadmill.
Do not throw away any packing materials until the unit is working properly.
Do not remove unit from box until it has been fully assembled.
Make sure the electrical cord will easily reach an electrical outlet.
If at anytime you need assistance with assembly, call 888-340-0482.
Locate the hardware pack and identify the following parts required for assembly.
Tools:
1. Allen Wrench- 3/16”
2. Allen Wrench- 7/32”
3. Phillips Screwdriver
5
Assembly
Assembly requires the included Allen wrench and Phillips screwdriver. Leave the unit on the
original packing material to assemble all parts.
Do not plug in the power cord until all assembly steps are completed.
1. Remove top cover of box, and break
the sides of the box to create a level
assembly surface. After opening the box,
remove any packing material from the
treadmill. Carefully cut the strap surrounding the treadmill, only while the
treadmill is laying flat.
Do not remove unit from box until it
has been fully assembled.
2. Locate the left upright. Slide the left
upright onto the base frame.
Secure the left upright to the base frame
by using four bolts M10x25 and four wash-
ers 10.
Note: Do not tighten hardware until step
5 has been completed.
Figure 1: Unpacking Treadmill
Left Upright
Bolt M10x25
Washer 10
Base Frame
Figure 2: Left Upright Installation
6
Assembly
3. Locate the right upright. Connect the
console harness together. One side of harness is located near the motor cover on
the bottom right side. The other end is
located inside the right upright.
Note: Make sure that the console har-
ness is inside of the upright and not being
pinched.
Slide the right upright onto the base
frame. Secure the right upright to the
base frame by using four bolts M10x25
and four washers 10.
Bolt M10x25
Washer 10
Console
Harness
Figure 3: Right Upright Installation
Washer M8
4. Locate the cross bar. Slide the cross
bar in between the left and right uprights.
Secure the cross bar using one washer M8
and one bolt M8x57 on each side.
Cross Bar
Bolt M8x57
Figure 4: Cross Bar Installation
7
Assembly
5. Feed the console wire coming out of the
console through the tube of the right handlebar. Connect the EKG harness and the
toggle harness coming from the handlebar
to the EKG harness and the toggle harness
coming from the console.
Secure the left and right handlebars to console using two bolts M8x50 and two washers M8 per side.
NOTE: Make sure not to pinch any wires
when securing the left handlebar.
Bolt M8x50
Washer M8
EKG
Harness
Left Handlebar
Toggle
Harness
Console Harness
Toggle
Harness
EKG
Harness
Right Handlebar
6. Connect the console harness together.
One side of harness is coming from the
right upright. The other end is coming
from the console.
Attach the console onto the uprights by
sliding into the uprights.
NOTE: Make sure that the console har-
ness is inside of the upright and not being
pinched.
Secure the console to the uprights using
two bolts M10x25 and two washers M10
per side.
IMPORTANT PLEASE NOTE:
Tighten all hardware installed in Step 2
through Step 6.
Figure 5: Console Assembly
Console
Washer M10
Console
Harness
Bolt M10x25
Figure 6: Securing Console Assembly to Uprights
8
Assembly
7. Locate the left and right covers.
Secure the covers to the console using
three screws on each side.
NOTE: Make sure not to pinch or screw
through any wires when securing the left
handlebar.
Screw ST4.2x12
Left Cover
Console
Right Cover
Figure 7: Cover Installation
Congratulations!
You have completed the assembly of your new HT-760T Treadmill!
Please remove the treadmill out of the box.
9
Moving Instructions
Caution! To Avoid The Risk Of Injury, Never Attempt To Move The Treadmill While It
Is In The Unfolded Operating Position.
With the treadmill in the folded locked position (safety latch is engaged) grasp the handlebars
and simply start rolling to desired location. Do not attempt to move the treadmill over an
uneven or rough surface.
10
Power Requirements
Improper connection of the equipment grounding connector can result in a risk of an
electric shock. Check with a qualified electrician or service man if you are in doubt as
to whether the product is properly grounded. Do not modify the plug provided with
the product. If plug will does not fit into the outlet, have a proper outlet installed by
a qualified electrician.
This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical
power. Voltage spikes, surges, and noise interference can result from weather conditions or
from other appliances being turned on or off. To reduce the possibility of treadmill damage,
always use a dedicated surge protector (not included) with your treadmill.
Surge protectors can be purchased at most hardware stores. The manufacturer recommends
a single outlet surge protector with UL 1449 rating as a Transient Voltage Surge Suppressor
(TVSS) with UL suppressed voltage rating of 400V or less and an electrical rating of 120VAC,
15 amps.
This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides
a path of least resistance for electric current should the treadmill malfunction. This treadmill
comes with an electrical cord with an equipment-grounding conductor and a grounding plug.
Always plug the power cord into a surge protector, and plug the surge protector into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not connect other equipment to the surge protector or this could cause permanent
damage to your treadmill.
This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like
the plug illustrated in the drawing below.
11
Loading...