KeyScan KSMART3 User Manual

8

Keyscan Inc. A Member of the Kaba Group

901 Burns St. E., Whitby, Ontario, Canada L1N 0E6

1.888.539.7226 (toll free Canada/USA)

905.430.7226 (elsewhere)
www.keyscan.ca
Technical Support
Hours — 9:00 AM to 6:30 PM Eastern Time
K-SMART3 Installation Guide (Document # KD10085-1017)

FCC Compliance Statement: This device complies with part 15 of the FCC rules. Operation
is subject to the following two conditions: (1) this device may not cause harmful interfer­ence, and (2) this device must accept any interference received, including interference
that may cause undesired operation.

Product can be used without license conditions or restrictions in all European Union coun­tries, including Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxem­bourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Spain, Sweden, United
Kingdom, as well as other non-EU countries, including Iceland, Norway, and Switzerland.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause unde­sired operation of the device.

Cet appareil est conforme à Industrie Canada exempts de licence standard RSS (s) . Le
fonctionnement est soumis aux deux conditions suivantes : (1) ce dispositif ne peut pas

provoquer d’interférences et (2) ce dispositif doit accepter toute interférence, y compris

les interférences qui peuvent causer un mauvais fonctionnement du dispositif.

Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequen­cy energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be re­quired to correct the interference at his own expense.

Changes or modifications not expressly approved by Keyscan could void the user’s au-

thority to operate the equipment.

K-SMART3 Bluetooth Proximity Reader

Installation Guide

This guide outlines how to install the K-SMART3 Bluetooth proximity reader. This reader
has dedicated function LEDs and enhanced security features designed for Keyscan access
control systems with compatible firmware. Enhanced security and LED features may not
function with non-Keyscan control boards. See K-SMART3-ACU Compatibility on page 3.

Keyscan Inc. A Member of the Kaba Group

901 Burns Street East, Whitby, Ontario, Canada L1N 0E6

K-SMART3 Features

• Uses proven digital radio frequency

identification technology

• Has dedicated access and power LEDs

• Designed for indoor or outdoor use

• Suitable for mullion or single-gang

mounting

• Electronics sealed in tamper-resistant

epoxy potting

• Bluetooth functionality

Table of Contents

Features 1

LEDs & Security Features 2-3

Bluetooth Functionality 3

Dimensions & Templates 4-5

Wiring Connections 6

Optional Programming Card

7

Specifications 7

Parts List

K-SMART3 Reader 1

Wall Switch Plate 1

Mullion Mount Box 1

6-32 x 1/4” Phillips Screw 1

6-32 x 1/4” Security Screw 1

6-32 x 1” Screws 2

#6 x 1” Screws

2

Enhanced Features

• Has dedicated Present3 and Global

Lockdown LEDs

• Offers physical and cable anti-tamper

capability for enhanced security
(tamper switch not included)

• Has innovative heartbeat to detect

wiring faults and/or reader damage

2

K-SMART3 Overview

LEDs and Security
Features

The K-SMART3 has 4 distinct
LEDs to report the state of a
system-specific function. In
addition, the K-SMART3 has
an anti-tamper capability
and a heartbeat for en­hanced reader security. The
following sub-headings re­view the K-SMART3’s LED,
anti-tamper and heartbeat
functions. Control boards
require System PROM ver­sion 9.39 or higher when
connected to a K-SMART3
reader for full functionality;
for example, using LED 3 for
Present3 or LED 4 for Global
Lockdown.

KEYSCAN

KI-00556E-06 -16

Secure reader to plate with
enclosed security screw*.

1

2

3

4

* Both Phillips &
#10 PIN Torx

screws provided.

Torx driver not
included.

LED 1—Door Lock State

• Red—indicates the door is locked / remains red on an Access Denied

• Green—indicates the door is unlocked / green during Relay Unlock Time On and

Access Granted

The control board must be configured for Reader LED (Red/Green Enabled) mode.

LED 2—Power

The backlit Keyscan logo indicates reader power:

• Not illuminated—indicates the reader does not have power

• Illuminated blue—indicates the reader has power

LED 3—Present3

The Present3 mode can trigger a door lock and change time zone schedules. When con­figured for operation at the reader, LED 3 functions as follows:

• Not illuminated—Present3 is off/Door Toggle - locked/Schedule - time zone is on

• Illuminated amber—Present3 is on/Door Toggle - unlocked/Schedule - time zone is

off

LED 4—Global Lockdown

LED 4 indicates when a Global Lockdown is in effect as follows:

• Not illuminated—a Global Lockdown is not in effect

• Illuminated red—a Global Lockdown is in effect

The reader must be connected to a control board that has Global Lockdown configured.

Note: LED 3—Present3 and LED 4—Global Lockdown are unique features for Keyscan
control boards and require System PROM firmware version 9.39 or higher.

7

K-SMART3 Enhanced Features

K-SMART3 enhanced features, which include Heartbeat and Tamper, are turned on by
default. With the purchase of the K-PC2 programming card, K-SMART3 enhanced features
can be toggled on and off. This will enable backwards compatibility with previous versions
of Keyscan ACUs, even if they do not have the required firmware 9.39 or higher to work
with other manufacturer’s access control systems.

If the K-SMART3 enhanced features are used on an un-supported access control board,
the reader will produce a Card Not in ACU alarm approximately every 60 seconds. This
will not affect the reader’s ability to read cards.

Keep this programming card close at hand for future use with any K-SMART3 reader to
toggle the enhanced features on or off. K-PC2 programming cards are available in pack­ages of 5 individual cards.

Specifications

Dimensions:

Mullion: 11.5 cm x 4.49 cm x 1.7 cm (4 7/16” x 1 11/16” x 11/16”)
Wall Plate: 12 cm x 7.6 cm x 1.6 cm (4 3/4” x 3” x 5/8”)

Power Requirements

12 VDC, 125mA

Read Range (with typical clamshell card)

Off Metal: up to 3 cm
On Metal: up to 3 cm

Cable

18” wire pigtail standard
Wiegand interface—22 AWG 6 conductor shielded cable, 152 metres/500 ft. maximum

Environmental

Operating Temperature: -40 to 66 °C (-40 to 150.8 °F), 93% RH

Installation

Installation and wiring of systems must be in accordance with the National Electrical
Code, ANSI/NFPA 70.

Connections

Connections must be in accordance with NFPA 70. Reader and/or control unit power
sources must not be connected to a receptacle controlled by a switch.

Certifications

UL-294 - Fifth Edition, CAN/ULC-S319-5 - First Edition, FCC ID: WFW-KSMART3 & IC:
5241A-KSMART3, ETSI EN 301 489-1 V2.1.1 (2017-02), ETSI EN 301 489-3 V2.1.1
(2017-03), ETSI EN 301 489-17 V3.1.1 (2017-02), EN 55032: 2012/AC:2013, ETSI EN
300 330 V2.1.1 (2017-02), ETSI EN 300 328 V2.1.1 (2016-11), Canadian Industrial De­sign Certificate of Registration: 169,198 and 169,199.