Kettler RIGA 07042-700, RIGA 07043-900, RIGA 07043-700, RIGA 07042-900 User Manual

Montageanleitung Tischtennistische

„RIGA“ und „RIGA PRO“

Art.-Nr. 07042-700, 07043-700, 07042-900, 07043-900

Der Umwelt zuliebe: Wir drucken auf 100% Altpapier!

F

D

GB

NL

E

I

PL

3

Assembly Instructions

Before assembling or using the table-tennis table, please read the following instructions carefully. They contain impor­tant information for use and maintenance of the equipment as well as for your personal safety. Keep these instructions
in a safe place for maintenance purposes or for ordering spare parts.

All KETTLER products are designed in accordance with the latest safety regulations and undergo a constant process of quality control
during manufacturing. The knowledge gained in this process is used to constantly improve and develop our products. In order to offer
our customers the very best in product quality, we reserve the right to make technical changes at any time. In spite of this, should you
have any cause for complaint, please contact your KETTLER dealer.

GB

Note on Safety

■ The table-tennis table should be used only for its intended pur-

pose, i.e. for playing with suitable table-tennis bats and balls.

■ All other uses are prohibited and may be dangerous. The man-

ufacturer cannot be held liable for damage or injury caused by
improper use of the table.

■ Damaged or worn components may endanger your safety or

shorten the lifespan of the table-tennis table. Replace worn or
damaged components immediately and remove the table from
use until this has been done. Use only spare parts manufactured
by KETTLER.

■ The table-tennis table complies with all safety regulations. In-

correct repairs, alterations to the design (removal of original
parts, addition of other components etc.) may endanger the
safety of the user.

■ Instruct other persons (in particular children) using the table in

its correct use, and draw their attention to any potential source

of danger, especially when setting up or dismantling the table.

■ When setting up or dismantling the table, stay clear of its fold-

ing radius.

■ When folded up, the table-tennis table presents a large surface

to the wind. For this reason, ensure that it is stored in a shel­tered position.

■ The table-tennis table may be pushed only into the transport po-

sition because there is otherwise a danger of injury.

■ The unit complies with the standard EN 14468–1:2004.

■ Depending on frequency of use, check all screws, bolts etc. reg-

ularly to ensure that they are in good condition.

■ Caution: While assembly of the product keep off children’s

reach (Choking hazard - contains small parts).

■ In case of enquiry, please contact your KETTLER dealer.

Handling the equipment

■ Do not use the table-tennis table until it has been fully and cor-

rectly assembled and checked.

■ Ensure that table-tennis tables which are not weatherproof are

not exposed to dampness or rain. Keep them well away from
direct sources of heat. Should the surface become warped, lay
the table on a level surface for a few days.

■ Set the table up on a level surface.

■ Do not cover it with plastic foil, under which condensation may

form. We recommend the weatherproof KETTLER tarpaulin, art.
no. 07032-000.

■ For practising without a partner, the table halves can be folded

up singly.

■ For more information on the sport of table-tennis, you are re-

ferred to the specialist literature on the subject.

■ Do not use corrosive or abrasive materials to clean the equip-

ment. Ensure that such materials are not allowed to pollute the en­vironment. In most cases, a slightly dampened cloth is sufficient.

■ Waste Disposal: KETTLER products are recyclable. At the end of

its useful life please dispose of this article correctly and safely
(local refuse sites).

CH

A

D

Assembly Instructions

GB

Instructions for Assembly

■ The equipment must be assembled with due care by two adult

persons.

■ Ensure that you have received all the parts required (see check

list) and that they are undamaged. Should you have any cause
for complaint, please contact your KETTLER dealer.

■ Before assembling the equipment, study the drawings carefully

and carry out the operations in the order shown by the dia­grams. The correct sequence is given in capital letters.

■ Please note that there is always a danger of injury when work-

ing with tools or doing manual work. Therefore please be care­ful when assembling this machine.

■ Ensure that your working area is free of possible sources of dan-

ger, for example don’t leave any tools lying around. Always dis­pose packaging material in such a way that it may not cause
any danger. There is always a risk of suffocation if children
play with plastic bags!

■ The fastening material required for each assembly step is shown

in the diagram inset. Use the fastening material exactly as in­structed.

■ Bolt all the parts together loosely at first, and check that they

have been assembled correctly. Tighten the locknuts by hand
until resistance is felt, then use spanner to finally tighten nuts
completely against resistance (locking device). Then check that
all screw connections have been tightened firmly. Attention:
once locknuts have been unscrewed they no longer function cor­rectly (the locking device is destroyed), and must be replaced.

■ For technical reasons, we reserve the right to carry out prelimi-

nary assembly work (e.g. addition of tubing plugs).

■ Please keep original packaging of this article, so that it may be

used for transport at a later date, if necessary. Goods may only be
returned after prior arrangement and in (internal) packaging, which
is safe for transportation, in the original box if possible. It is impor­tant to provide a detailed defect description / damage report!

List of spare parts

When ordering spare parts, always state the full item number,
spare-partnumber, the quantity required and the S/N of the pro­duct (see spare parts drawing).

Example order: item no. 07042-700 / spare-part no. 10100016

/ 2 pieces / S/N......

Important: spare part prices do not include fastening material; if
fastening material (bolts, nuts, washers etc.) is required, this

should be clearly stated on the order by adding the words „with

fastening material“.

KETTLER GB Ltd. · KETTLER House, Merse Road · North

Moons Moat · Redditch, Worcestershire B98 9HL
KETTLER International Inc. 1355 London Bridge Road · Vir-

ginia Beach, VA 23453

http://www.kettler.net

USA

GB

11

2x M8

8x M6

4x M6

22x ø12

18x ø16

10x ø25

8x

4x

4x

4x M8

2x ø20

2x

4x M6x55

4x M8x45

4x M6x60

4x M6x35

6x M6x36

4x M8x110

2x M8x120

4x

2x

2x

2x

1x

2x

2x

2x

1x

2x

1x

2x

4x

2x

(7042)

2x

(7043)

2x

4x

2x

2x1x

2x

6x

2x

4x ø26

SW13 SW10

2x 2x 1x

GB E

F

NL

I

PL

Checkliste (Packungsinhalt)

Checklist (contents of packaging)

Liste de vérification (contenu de l’emballage)

Checklijst (verpakkingsinhoud)

Lista de control (contenido del paquete)

Lista di controllo (contenuto del pacco)

Lista kontrolna (zawartość opakowania)

Sie benötigen zusätzlich folgendes Werkzeug (Gehört nicht zum Lieferumfang):
You also need the following tools (Not included):
Vous avez besoin de cet util en complément (con compris dans la livraison)
U heeft tevens volgend gereedschap nodig (Is niet in de levering ingesloten):
Usted necesita adicionalmente la siguiente herramienta (no pertenece al volumen de suministro):
Per eseguire il montaggio, Vi occorre il seguente attrezzo (non è incluso nel volume di fornitura):

Dodatkowo potrzebne są następujące narzędzia (nie objęte zakresem dostawy):

PL

I

E

NL

F

GB

D

12

Actuel size of hardware

M8x120

M8x110

M8x45

M6x60

M6x55

M6x35

M6x37

M6

M8

ø16x6

ø12x6

ø25x8

6x9.5

M6

M6

M8

ø12x6

ø20x6

ø26x19

13

Messhilfe für Verschraubungsmaterial

Measuring help for screw connections

Gabarit pour système de serrage

Meethulp voor schroefmateriaal

Ayuda para la medición del material de atornilladura

Misura per materiale di avvitamento

Wzornik do połączeń śrubowych

GB

F

NL

E

I

PL

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

M5x40

M8x40

M8

˘22

˘16

˘12

M6

M5

˘3,9x13

Beispiele Examples Examples Bij voorbild Ejemplos

M5x40

1

4x

M6x35

4x

4x

ø12

!

!

14

2

C

A

D

A

ø25

AB

B

2x

M8x120

2x

ø16

2x

ø25

2x

M8

C

2x

M8x110

8x

ø16

2x

M8

2x

M8x110

8x

ø16

2x

3

18,6cm

15

4

A

2x

M6x55

B

2x

ø16

B

2x

M6x55

4x

ø16

2x

A

B

A

16

5

B: Die Streben des Tragrahmens müssen hierbei ein wenig
zur Seite gebogen werden; gehen Sie hierbei vorsichtig vor!
C: Setzen Sie nun eine Plattenhälfte auf. Sichern Sie die Plat­tenhälfte für die folgenden Montageschritte unbedingt gegen
Abrutschen und/oder Umkippen! Lassen Sie von einer zwei­ten Person auf jeder Seite die Schubstrebe und die Tragrah­menstrebe auf das letzte Verbindungsrohr aufschieben.
D: Das Verbindungsrohr wird nun mit den Seitenteilen ver­schraubt.

B: To do this, the braces for the frame must be bent slightly to
the side. Proceed with care when doing this.
C: Position one of the table halves and ensure that it cannot
slip or tilt over. Ask another person to attach the push bar and
the support-frame brace to the last connecting bar.

D: The connecting bar is now bolted to the side elements.
B: Pour cela les jambes de forces du cadre porteur doivent

être pliées un peu de côté; pratiquer là avec précaution.
C: Poser un plateau. Il est absolument nécessaire de sécuriser
les plateaux pour les opérations de montage qui suivront, afin
qu’ils ne puissent ni glisser ni se renverser. Demander à une
autre personne de glisser de chaque côté l’entretoise et la
jambe de force du cadre porteur sur le dernier tube de jonc­tion.

D: Visser ensuite le tube de jonction aux pièces de côté.
B: De stangen van het draagframe moeten hierbij aan de

kant enigszins gebogen worden; ga bierbij voorzichtig te
werk!
C: Stel een bladhelft op. Blokkeer deze bladhelft voor het vol­gende deel van de montage tegen wegglijden en/of kante­len. Laat een volwassene aan elke zijde de schuifstang en het

NL

F

GB

D

draagframe over de laatste verbindinggsbuis schuiven.
D: De verbindingsbuis moet nu aan de zijdelen worden vast­geschroefd.

B: Los puntales del marco soporte tienen que ser ligeramente
doblados; ¡ejecute este proceso con cuidado!
C: Ponga la mitad de la plancha. ¡Asegure la mitad de la
plancha para los próximos pasos de montaje contra desliza­miento y/o vuelco! Deje que una segunda persona empuje a
cada lado el puntal de empuje y el puntal del marco en el úl­timo tubo de unión.

D: El tubo de unión es atornillado con las partes laterales.
B: A questo proposito è necessario piegare leggermente verso

il lato i montanti della staffa di supporto; procedere con cautela!
C: Dispore un semipiano. Assicurarsi che il semipiano sia fis­sato bene, in modo da non scivolare o ribaltarsi durante le
fasi successive di montaggio! Da una seconda persona far
posizionare i sostegni scorrevoli su ciascun lato e il sostegno
del telaio portante sull’ultimo tubolare di collegamento.
D: Il tubolare di collegamento adesso avvitato con i compo­nenti laterali.

B: Poprzeczki pałąka podporowego muszą zostać przy tym
nieznacznie rozgięte na zewnątrz. Zachować przy tym
ostrożność!
C: Po jednej stronie ułożyć połówkę płyty. Dla następnych
operacji montażowych należy koniecznie zabezpieczyć
połówkę płyty przed ześlizgnięciem się i/lub przewróceniem
się! Poprosić drugą osobę o nasunięcie po obu stronach po­pychaczy ukośnych i podpór ukośnych ramy na ostatnią rurę
łączącą.
D: ura łącząca skręcona zostaje teraz z częściami bocznymi.

PL

I

E

2x

M8x45

4x

ø25

D

A

A

B

C

2x

ø26

17

6

2x

M6x60

4x

2x

2x

M6

7

4x

ø12

2x

M6

1x

M6

1x

M6x362xM6x36

2x

ø12

1x

ø20

A

A

B

B

B

A

B

18

10

9

8

Führen Sie die Schritte 5 bis 8 für die zweite Plattenhälfte durch. Denken Sie auch hier wieder an die Sicherung der Platte!
Carry out steps 5–8 for the second half of the table. Again, ensure that the table cannot slip or tilt over!
Effectuer les opérations 5 à 8 pour la deuxième moitié de table. Là non plus, ne pas oublier la sécurisation du plateau.
Voer de montagestappen 5 tot 8 voor de tweede bladhelft uit. Denk ook hierbij weer aan de vergrendeling van het blad!
Ejecute los pasos 5 a 8 para la segunda mitad de la plancha.
Ripetere le operazioni da 5 a 8 anche per il sesondo semipiano

Powtórzyć kroki 5 do 8 dla drugiej połówki płyty.

D

GB

F

NL

E

I

PL

CLICK!

CLICK!

19

Herunterklappen der Plattenhälften

Lowering the table halve

Rabattre les moitiés de la table

Neerslaan van de plaathelften

Despliegue de los dos segmentos de la placa

Ribaltare le metà del tavolo

Opuszczanie płyt stołu

GB E

F

NL

I

PL

Drücken Sie die rechte Kippsicherung. Anschließend die Plat­te mit einer Hand festhalten, linke Kippsicherung drücken und
Platte langsam herunterklappen (Platte unter keinen Umstän­den einfach fallen lassen!).

Press the right-hand tip lock. Hold the table firmly with one
hand, press the left-hand lock and lower the table-half slowly
into position. Never allow it to drop down!

Appuyer sur la sécurité de basculement de droite. Tenir en­suite le plateau d’une main, appuyer sur la sécurité de bas­culement de gauche et laisser descendre lentement le plateau
(en aucun cas on ne pourra le laisser tout simplement tom­ber).

Druk de rechter kiepvergrendeling in. Houd het blad dan met
een hand vast, druk op de linker kiepvergrendeling en klap
het blad langzaam naar beneden (laat het blad in geen ge­val zomaar vallen!).

NL

F

GB

D

Presione el seguro derecho. Sujete a continuación la plancha
con una mano y presione el seguro izquierdo contra vuelco.
Baje lentamente la plancha (¡no deje caer la plancha por
ningún motivo!).

Premiere il pulsante antiribaltamento destro. Sostenendo il pi­ano con una mano, premere il pulsante antiribaltamento si­nistro e abbassare lentamente il piano stesso (per nessun mo­tivo lasciare il piano in caduta libera!)

Nacisnąć prawe zabezpieczenie przed przewróceniem się.
Następnie przytrzymać płytę jedną ręką, nacisnąć zabez­pieczenie przed przewróceniem się po lewej stronie i powo­li opuścić płytę (pod żadnym pozorem nie pozwolić płycie
opaść pod własnym ciężarem!).

PL

I

E

C

A

B

20

Zusammenklappen der Plattenhälften

Collapsing the table halves

Replier les moitiés de la table

Tesamenslaan van de plaathelften

Plegar los segmentos de las placas

Chiudere le metà del tavolo

Składanie płyt stołu

GB E

F

NL

I

PL

Drücken Sie den Hebel der Standsicherung nach oben und
heben Sie die Plattenhälfte an. Behalten Sie in der Anfangs­phase des Hochklappens den Druck bei.

Press the locking lever up and lift the table half upwards. Con­tinue to press the lever during the first part of the upward mo­tion.

Pousser le levier de la sécurité vers le haut et soulever le demi­plateau. Maintenir la pression dans la phase initiale du re­dressement.

Druk de linker kiepvergrendeling naar boven en til de blad­helften op. In het begin dient u hierbij druk uit te oefenen.

F

GB

D

NL

Presione la palanca de seguro de la estabilidad hacia arriba
y levante la mitad de la mesa. Mantenga la presión en la
fase inicial del levantamiento.

Premere verso l’alto la leva del dispositivo stabilizzatore e
sollevare il semipiano. Mantenere la pressione nella fase ini­ziale del sollevamento del semipiano.

Obrócić dźwignie podpór w górę i podnieść połówkę płyty.
W początkowej fazie podnoszenia należy nadal naciskać
zabezpieczenia.

E

I

PL

A

B

21

2

1

2x

M5x32 M5

B

A

C

Montage des Netzhalters

Instructions for Assembling the net set

Instructions de montage pour l’ensemble poteaux-filet

Montage van de netpost

Montaje del portared

Montaggio dell’attacco della rete

Montaż uchwytu siatki

GB E

F

NL

I

PL

15 cm

22

Ersatzteilzeichnung

Spare parts drawing and list

Dessin et liste des pièces de rechange

Reserveonderdeeltekening en -lijst

Designación y lista de las piezas de recambio

Disegno ed elenco dei pezzi di ricambio

Rysunek i lista części zamiennych

GB E

F

NL

I

PL

7042

7043

8

1

2

11

9

3

6

4

Typenschild – Seriennummer
Type label – Serial number
Plaque signalétique – Numèro de serie
Typeplaatje – Seriennummer
Placa identificativa – Número de serie
Targhetta tecnica – Numero di serie
Tabliczka identyfikacyjna – Numer serii

HEINZ KETTLER GmbH & Co. KG

D-59469 Ense-Parsit

Art.-Nr. 07044-000

1-334 O - 1801 00001

geprüft nach prEN 14468-1, -2

Klasse C, Typ 4

Made in Germany

21

5

12

21

31

30

35

32

14

10

1

2

10

4

15

20

27

13

36

16

24

19

18

28

17

5

33

34

23

1 TT-Platte (BITTE UNBEDINGT ARTIKEL-NUMMER DES TT-TISCHES ANGEBEN!) 2 94130117 94130000 94130125 94130003
2 Fussbügel/-gestell mit Bodenschonern 2 94111232 94111232 94111247 94111247
3 Bodenschoner 4 70130540 70130540 70130540 70130540
4 Stützbügel

(mit Rohrverbindern, Sicherungen, Bundschrauben M6x30mm) 2 94111237 94111237 94111250 94111250

5 Sicherungshebel 1 4 94111234 94111234 94111234 94111234
6 Sicherungshebel 2 2 94111233 94111233 94111233 94111233
8 Rohrschelle für ø25mm 4 94110341 94110341 – –

9 Rohrschelle für ø18mm 4 94110192 94110192 – –
10 Lagerböckchen 8 – – 10128028 10128028
11 Schubstange 2 94111239 94111239 94111239 94111239
12 Schubstange mit Sicherungshebel 2 94111240 94111240 94111240 94111240
13 Verbindungsstange 2 94110912 94110912 94110912 94110912
14 Grundbügel (714mm) 1 94111242 94111242 94111242 94111242
15 Radhalter 2 70130811 70130811 70130811 70130811
16 Grundbügel (895mm) mit Stopfen für VKT 25mm 1 94111246 94111246 94111246 94111246
17 Abweisstange 2 70130607 70130607 70130607 70130607
18 Seitenverkleidung 2 70130608 70130608 70130608 70130608
19 Räder-Satz (4 Stück) mit Radverbinder 2 94180177 94180177 94180177 94180177
20 Radverbinder 2 70130812 70130812 70130812 70130812
21 Handdruckplatte 6 70130532 70130532 70130532 70130532
22 Bundschraube M6x37mm (o.Abb.) 6 10201209 10201209 10201209 10201209
24 Stopfen für VKT 25mm 2 10100046 10100046 10100046 10100046
25 6kant-Schraube M8x120mm (o.Abb.) 2 10206084 10206084 10206084 10206084
26 6kant-Schraube M8x110mm (o.Abb.) 4 10206081 10206081 10206081 10206081
27 Distanzrohr ø12x1,8x64mm 2 97201453 97201453 97201453 97201453
28 Spreizniet ø6x9,5 4 10418503 10418503 10418503 10418503
29 Schraubenbeutel (o. Abb.) 1 94180338 94180338 94180338 94180338
30 Netzhalter Automatik 2 94110103 94110103 94110103 94110103
31 Netz (kpl.) 1 94180065 94180065 94180065 94180065
32 Spannlasche 2 10128002 10128002 10128002 10128002
33 Netzhalter 2 94111243 94111243 94111243 94111243
34 Stopfen für VKT 20mm 2 10100095 10100095 10100095 10100095
35 Rändelschraube 2 10106000 10106000 10106000 10106000
36 Verbindungsstange 1 94111241 94111241 94111241 94111241
37 Schraubenbeutel für Netzmontage (o. Abb.) mit Stopfen für VKT 20mm 1 94180143 94180143 94180143 94180143

Teil Bezeichnung Stück Ersatzteil-Nr. Ersatzteil-Nr. Ersatzteil-Nr. Ersatzteil-Nr.
Nr. 07042-700 07042-900 07043-700 07043-900

blau/schwarz grün/schwarz blau/schwarz grün/schwarz

nicht wetterfest nicht wetterfest wetterfest wetterfest

Ersatzteilliste

max 1 cm = ok.

max 1 cm = ok.

max 1 cm = ok.

docu 1064m/02.10

HEINZ KETTLER GmbH & Co. KG · Postfach 1020 · D -59463 Ense-Parsit

www.kettler.net