Kettler 2548 User Manual

810.59 Kb
Loading...

2548 ADIRONDACK ROCKING BENCH

Contents:

(18) 1/4 - 20 x 2” Bolts

(1)

Seat, (1) Back

(6)

1/4 - 20 x 2 1/2” Bolts

(2) Arm Rests

(1)

#10 x 3” Screw

(2)

Front Chair legs

(10) Washers

(2)

Back Chair legs

(10) Locknuts

(2)

Cross Braces

Locknut Washer Bolt

(2)

Rocker Feet

 

 

Tools Required:

#3 Phillips Head Screwdriver

7/16” Wrench

a.Align predrilled holes then insert bolts

1.to attach front legs.

b.Align predrilled holes then insert bolts

to attach back legs.

1a.

1b.

2.

Place arm rest

 

 

 

on top of chair

 

 

 

legs, align front

 

Attach the back

 

predrilled holes,

3.

 

of the chair by

 

insert bolt.

 

aligning holes on

 

 

 

 

 

 

the arm and the

 

 

 

seat to insert bolt.

3b.

3a.

4.

Attach the braces to

the legs by 5. aligning holes

and inserting a 2” bolt.

Attach the rocker to the legs by

aligning holes to metal insert, use a 3” bolt.

6.

Insert the bolt thru the center seat brace into the center of the back of bench.

Assembly Instructions

1.a. With the wing on the post facing front, align the predrilled holes on front leg to the seat and insert the 1/4 - 20 x 2” Bolts through the leg in thru the seat. Clean any plastic residue from the bolt then slide a washer on. Screw on the locknut and then tighten it with the wrench and phillips screwdriver.

b.Align the predrilled holes on the back leg to the seat and insert the 1/4 - 20 x 2” Bolts through the leg in thru the seat. Clean any plastic residue from the bolt then slide a washer on. Screw on the locknut and then tighten it with the wrench and phillips screwdriver. Repeat on the other front leg.

2.Place arm rest on top of chair legs align the front predrilled holes and insert the 1/4 - 20 x 2” Bolts through the leg and in thru the arm. Clean off any plastic residue then slide a washer on the end of bolt. Screw on the locknut and then tighten it with the wrench and phillips screwdriver.

3.a. Attach the back of the chair to the seat by aligning holes and inserting a 1/4 - 20 x 2” Bolt then tighten with a phillips screwdriver.

b. Attach the back of the chair to the arm by aligning holes and inserting a 1/4 - 20 x 2 1/2” Bolt thru the arm, leg and into the chair back, then tighten with a phillips screwdriver.

Repeat on both sides.

4. Attach the cross braces of the chair to the legs by aligning holes and inserting a 1/4 - 20 x 2” Bolt through the leg into the cross brace and tighten with a phillips screwdriver.

Repeat on other leg.

Do Front and Back cross braces.

5. Attach the rocker for the chair. Align the predrilled hole on the rocker to the metal isert at the bottom of each leg and insert a 1/4 - 20 x 2 1/2” bolt then tighten with the screwdriver.

Bolt rocker to both front and back legs.

6. Attach the center seat brace underneath to the back, insert a #10 x 3” screw thru the brace into the center of the bottom back support then tighten with the screwdriver.

 

Made in the U.S.A.

 

www.kettlerusa.com

Copyright © Kettler USA 309.01

info@kettlerusa.com

 

+ 1 hidden pages