SAFETY AND OPERATING
MANUAL
QUIKY ELECTRIC
WATER BLASTER
Read Safety & Operating Instructions
Before Commencing Operation
2
Safety & Operating Manual
Quiky Electric Water Blaster
THESE INSTRUCTIONS MUST BE READ AND ADHERED TO
BEFORE OPERATING THIS MACHINE.
SAFETY MANAGEMENT PROCEDURES
Failure to comply with safety recommendations may result in injury to the operator, nearby
persons, or damage to property, or this machine.
Always transport your machine in an upright and horizontal position.
This machine can cause severe injury if the water jet is pointed at any party of the body,
so keep hands, feet, other body parts and animals out of the pressure jet.
ALWAYS wear protective goggles and suitable protective clothing when this operating
appliance. Non-slip rubber footwear must be worn when operating this machine.
NEVER let the electric motor switch or electrical cord get wet. USE AN EARTH
LEAKAGE DEVICE.
Do not touch the appliance with wet/damp hands or feet and do not use the appliance bare-
footed or with unsuitable clothing.
Do not pull the supply cable or the appliance itself in order to disconnect the plug from the
electric supply.
NEVER run the machine without water in the pump.
Check engine and pump oil daily.
Check that water connections are tight and that there are no leaks from the machine.
DO NOT work the machine for more than 1 to 2 minutes with gun in CLOSED position.
After switching machine 'OFF' point lance in a safe direction and press trigger on gun
handle to release any built-up pressure before moving or working on this unit.
Protect machine from weather. DO NOT leave out in rain or freezing conditions. DO
NOT use if water pipes have frozen or if temperatures fall below zero, without taking
special precautions.
In case of damage or malfunction, switch off the appliance and disconnect it from the mains
electricity by removing the plug, then call an authorised service person.
DO NOT attempt to fix or repair the unit. All adjustments or overhauls should be carried
out by a Kerrick authorized service agent only.
Use only Kerrick accessories which are designed to operate with your machine.
WARNING:
Incorrect use or failure to follow operating and maintenance procedures may produce an injury to a
person or damage to the equipment.
3
Safety & Operating Manual
Quiky Electric Water Blaster
PARTS DESCRIPTIONS
CHECK CLEANER FOR DAMAGE CAUSED BY TRANSPORTATION, IMMEDIATELY AFTER
UNPACKING. IF DAMAGE IS FOUND CONTACT SUPPLIER IMMEDIATELY.
FOR SHIPPING REASONS, SOME PARTS MAY BE PACKED SEPARATELY. IN THIS CASE
ASSEMBLE PARTS AS INDICATED IN THIS BOOKLET.
1) Inlet hose connection with water filter
(INLET)
2) High pressure hose connection
(OUTLET)
3) Pressure adjusting knob
4) Pressure indicator
5) ON/OFF switch
6) Chemical regulator (CHEM.)
7) Chemical filter
8) Oil dipstick
9) Oil level indicator
10) Automatic gun
11) “Quick lance”
12) ROTOTEK / MULTIREG
13) High pressure hose
14) Safety lock
4
Safety & Operating Manual
Quiky Electric Water Blaster
SET UP PROCEDURES
a) Replace the red travel plug (1) with the vented black/yellow
dipstick provided (2).
b) Check that the oil in the sight glass sits at the half way level
(top up if necessary).
c) Connect one end of the high pressure hose to gun (A) and
the other to the outlet connection (B).
d) Assemble the lance by pushing the two halves together and
then fix by turning the connector (C).
e) Connect the water supply to the Inlet port (D) by means of a reinforced hose (minimum
15 bar / 200 psi) with and internal diameter of no less than 13mm (1/2”).
f) Water flow decreases as the length of hose gets longer.
Therefore, make sure the quantity of water supplied to
the machine is not less than the quantities indicated in
the chart on the right.
g) The pressure of the inlet water must not exceed 10 bar /
145 psi.
h) If the user prefers to power the water blaster via a water tank and suction, simply
emerge the end of the supply tube in a clean tank of water. 1meter is the maximum
suction depth considered (distance in height between the water surface and the pump).
WARNING:
The maximum temperature of the inlet water must not exceed 60°C.
Water supplied to the machine must be clean. Running the machine with no water or with water that
contains grit or corrosive liquids will cause catastrophic damage to the machine.
IMPORTANT:
Before using this machine make sure it has an ID label. If it does not have a label, do not use the
machine and consult your distributor immediately.
The identification label with technical specifications is placed on the back of the machine and is always
visible.
5
Safety & Operating Manual
Quiky Electric Water Blaster
CONNECTING TO THE ELECTRICAL SYSTEM
a) Check that the voltage of the electrical systems (mains supply) is the same as what is
indicated on the machine’s ID label.
b) Check that the plug supplied complies with local safety regulations, and that it is
provided with an earthed connection.
c) Check electrical cords, switch and plugs for damage. DO NOT USE if damage is found
or if electrical wiring is suspect. Call a Kerrick service agent if in doubt.
d) Do not connect other appliances to the same power outlet while using the machine.
e) Fully unwind the power cord when in use, to prevent overheating.
f) Use only extension cables with the same number of conductors as those of the machine
cable (including the earth) and with a suitable plug/socket for the cable to be used.
g) Only use extension cords designated for outdoor use. Such cables are marked “Suitable
for outdoor use.” This extension cord must be stored indoors when not in use.
h) Do not use a damaged extension cord. Cables should not be located near sources of
heat, sharp edges or water. Always disconnect the plug from the socket before
removing the extension cord from the product.
START UP
Before starting up the machine, ensure that it’s positioned on flat ground or leaning against a
stable support and that the resisting surface is level or with a minimum slope.
It is ESSENTIAL that you ensure the suction filter / inlet filter is clean before use (see
maintenance).
a) Whilst setting up keep machine switched off and unplugged from mains.
b) Connect water intake hose to pump.
c) Fit discharge hose to quick lance / shut off gun.
6
Safety & Operating Manual
Quiky Electric Water Blaster
d) Check that pump has correct oil content – check sight glass. Oil should be half way up
sight glass. Also check breath hole in oil cap is clear. To stop oil from spilling when
transporting machine the breath hole may be closed by a pin, adhesive tape or a sealed
cap. Remove pin, adhesive tape or replaced sealed cap with dip stick cap, so that
breath hole is clear.
e) Set the pressure to zero by turning the knob anti-clockwise.
f) Turn on water supply. Maximum inlet water temperature must not exceed 60° C.
g) Check that there are no water leaks and ensure that the hose has no kinks or twists.
h) Before starting, point the lance to a safe position and open the gun trigger to release
any built-up pressure in the system. CHECK water is flowing through the machine and
out the lance prior to starting.
i) Once all checks have been completed, plug the unit into the electrical mains supply.
With single phase machines an earth leakage device is recommended.
Never let electric cords lie in pools of water
Keep plugs and motor dry at all times
DO NOT use long extension cords
j) Turn machine switch to the “ON” position while holding the trigger on the shut off gun
open to relieve back pressure.
k) Releasing the trigger will shut off the water flow.
a) Adjust the machine to your required pressure and then begin water blasting.
l) After turning unit off ALWAYS release pressure in gun. DO NOT leave pressure built up
in the hose gun.
To eliminate any impurities or air bubbles from the water circuit we advise starting the cleaner
for the first time without the lance and letting the water run out for a few seconds. Impurities
could block the nozzle and cause malfunction.
ALWAYS TURN OFF POWER SUPPLY AT THE WALL SOCKET AFTER USE, OR IF
MACHINE FAILS TO OPERATE.
WARNINGS:
Never let the unit run for more than 1 to 2 minutes with the gun
closed. Water will recycle within the pump head and heat up, causing
damage to seals.
Never let pump run dry of water as this can cause catastrophic
damage to the pump.
When your water blaster is not in use, close the safety device on the
handle (FIG 1).
7
Safety & Operating Manual
Quiky Electric Water Blaster
THE MANUFACTURER CANNOT BE HELD RESPONSIBLE FOR ANY DAMAGE CAUSED
BY OPERATORS DISRESPECTING THE DESIGNATED USES OF THIS MACHINE, ITS
INDSTRUCTIONS AND WARNINGS INDICATED IN THIS BOOKLET.
DETERGENT APPLICATION
The unit can suck and mix detergents and other liquid chemicals thanks to an automatic
device incorporated in the unit itself, which is remote controlled by operated the ROTOREK
nozzle.
a) The unit is equipped with a chemical suction kit (Fig. A).
b) Fit the brass connector to the chemical control knob and filter
into the chemical container (Fig. B).
c) Select low pressure with a ROTOTEK (Fig. C).
d) At this point the suction and mixing of the chemical will start automatically.
e) You can regulate the quantity of chemicals by adjusting the chemical control knob (Fig.
D).
f) When you wish to stop using chemical (in order to clean or rinse), simply release the
gun trigger and adjust the ROTOTEK to high pressure. At this point the chemical
injection automatically stops.
IMPORTANT:
To extend the life of your cleaner, run the machine with clean water after every application of chemical.
IMPORTANT:
Do not cover the machine during use; ensure it’s used in a well ventilated area.
This machine is equipped with a thermal protector which trips and electrically disconnects the motor
when it overheats. Carefully read the troubleshooting guide before re-starting the unit again.
8
Safety & Operating Manual
Quiky Electric Water Blaster
Use of ROTOTEK or MULTIREG 99
Pressure selection must be carried out with a closed gun (1).
Pic A: Selection of the pressure
- High pressure (2)
- Low pressure (3)
Pic B: Selection of the jet
- Straight pin jet (4)
- Fan jet (5)
GENERAL CARE & MAINTENANCE
INSTRUCTIONS FOR STORAGE & PRECAUTIONS AGAINS FREEZING
This machine should be cleaned daily after use, and checked for any maintenance
requirements. After using the detergent system it should be flushed with clean water. Simply
stand the detergent intake in a clean bucket of water and run the machine with the pump
nozzle or valve open for one minute.
Release any pressure in the hoses by depressing the trigger on the gun. Drain surplus water
from hoses and check for damage before storage. If the hoses are damaged in anyway,
replace immediately. Make sure hoses are stored with no kinks in them.
Check oil levels in both pump and motor. Allow motor to cool down before storage.
Store your water blaster indoors and in a dry area. Never leave equipment outside unprotected
from the elements. In particular do not leave equipment in low or sub-zero temperatures. In
very cold conditions it may be necessary to protect equipment by flushing it with antifreeze.
When storing the cleaner for long periods we also recommend the use of antifreeze solution in
order to avoid corrosion and drying up of the pump seals.
To do so:
a) Mix up antifreeze mixture in a separate container, as per manufacturer’s instructions.
b) Couple the container to the intake of the machine and gravity feed to pump.
c) Run machine for one minute to ensure system is primed with antifreeze mixture.
d) On stopping the machine, release pressure in hose by pulling trigger.
9
Safety & Operating Manual
Quiky Electric Water Blaster
Remember: If the machine is operated in an area where freezing occurs, always check that
water lines are not frozen and take precautions to ensure that water does not freeze with the
pump. Before starting check that the water flow is normal. If in doubt do not use the
machine.
If in doubt about low temperatures or any long length of storage
time, we suggest you turn the motor with the key provided before
starting up. This activity helps to release any possible blockages
like ice or a buildup of lime scale deposits. Taking these
precautions before starting will avoid damage being caused to
the unit.
Remember to always remove the key before switching the
machine on.
OIL CHANGE
a) Regularly check the oil level to ensure it sits at the half way point in the sight glass, top
up as required.
b) Oil must be changed after the first 20 hours of operation of the machine. Subsequent oil
changes must be carried out every 150 hours of machine operation. It must be changed
at least once a year.
c) Used oil must be collected in containers and disposed of in special centers according to
current standards. It must not be discarded into the environment.
CLEANING THE INLET FILTER
Before using the machine it is important to make sure the filter is clean. Wash the filter under a
clean water tap or blow it with air to remove any dirt and debris. A well cleaned filter will help to
improve your water blaster’s performance and prolong the life of your machine.
10
Safety & Operating Manual
Quiky Electric Water Blaster
DISPOSAL OF THE MACHINE
In the case you should no longer require the use of this machine, it is advised to disconnect
the power cord making the machine inoperable.
The machine is considered “Special Waste” therefore do not dispose of it with regular
household rubbish. Used electric and electronic equipment must be handled separately and in
compliance with the local regulations relating to the treatment, recovery and recycling
procedures of said products.
NOTE: Incorrect use or failure to follow operating and maintenance procedures may produce
an injury to a person or damage to the equipment.
TROUBLE SHOOTING
WATER SYSTEM AND WATER PUMP
Trouble
Possible Cause
Remedy
The pump is
running but
maximum pressure
is not obtained.
Air sucked into pump
Check suction hose and fittings
Worn or dirty valves
Clean or replace as required
Inlet suction strainer clogged or
improper size
Clean. Use adequate size. Check more
frequently
Worn packing. Abrasives in pumped
fluid or severe cavitation
Install proper filter available to pump. Check
and/or replace packings.
Fouled or dirty inlet or discharge valves
Clean inlet and discharge valve assemblies
Worn inlet or discharge valves
Replace worn valves, valve seats and/or
discharge hose
Leaky discharge hose
Secure leak or replace hose
Fluctuating or
decreasing
pressure
Damaged, dirty or clogged valves
Check, clean and/or replace
Air is being sucked into the system
Check suction hose and fitting for damage.
Replace if required
Worn packings
Check and/or replace packings.
Dirty filter
Remove and clean filter using running water and
place back into machine.
Water dripping
from under pump
Piston packing worn
Check packings
Packing o-rings worn
Replace o-rings
REMEMBER:
Follow safety instructions.
Open trigger on gun when starting up and shutting down to back off pressure.
Do not run unit dry of water and check oil levels regularly.
Do not leave running with shut off gun closed for more than 1 or 2 minutes
Keep electric motor, switch, electric lead and plugs dry.
Use an earth leakage device.
11
Safety & Operating Manual
Quiky Electric Water Blaster
KERRICK SERVICING
Kerrick’s workshop facilities are staffed by experienced technicians providing servicing, repair
and manufacturing for a range of products including; water blasters, vacuum cleaners,
extractors, pressure cleaners, pumps and more. We work on everything from commercial and
light industrial to large heavy duty equipment and offer customized design build services. We
also warehouse and ship a comprehensive range of spare parts for your convenience.
For more information on your product, to book in a service or repair or to order spare
parts give Kerrick a call or send through and enquiry on our website. Contact details
can be seen below:
KERRICK NEW ZEALAND
0800 2 KERRICK (0800 253 774)
SALES@KERRICK.CO.NZ
WWW.KERRICK.CO.NZ
WATER SYSTEM AND WATER PUMP
Trouble
Possible Cause
Remedy
Excessive Noise
Air Suction
Check suction hose and fittings for damage and
loose connections.
Damaged, dirty or stuck valves
Clean or replace as required
Worn bearings
Check and replace as required
Water temperature too high
Lower water temperature to under 60°C
Dirty filter
Remove and clean filter using running water and
place back into machine.
Presence of water
in oil
Leakage of packing seals
Replace packing
High air humidity
Change oil twice as frequently as advised
Oil leakage
Oil seals worn
Replace oil seal
Motor hums but
does not run when
turned on
System voltage is lower than the
minimum advised
Check that power source is adequate
The pump is stuck or frozen
Turn the motor using the key (see page 9)
Extension cord is incorrect
Check extension cord is appropriate using the
Extension Cord Table (page 5)
The motor does not
start when
switched on
The plug is not well connected or there
is no power supply
Check the plug, cord and switch
The motor stops
The thermal protector has tripped due
to overheating
Check that the mains voltage corresponds with
the voltage required by your machine. Switch off
the motor and let it cool down for a few minutes
before tuning on the unit again.
KERRICK AUSTRALIA
1300 KERRICK (1300 537 742)
SALES@KERRICK.COM.AU
WWW.KERRICK.COM.AU
Loading...