KERN TEB, TEB 200-1 Operating Instruction
KERN & Sohn GmbH
Ziegelei 1
D-72336 Balingen
E-Mail: info@kern-sohn.com
Tel: +49-[0]7433- 9933-0
Fax: +49-[0]7433-9933-149
Internet: www.kern-sohn.com
Operating instruction
Pocket balance
KERN TEB
Version 1.0
10/2005
GB
TEB-BA-e-0510
TEB-BA-e-0510
2
GB
KERN TEB
Version 1.0 10/2005
Operating instruction
Pocket balance
Table of contents:
1 Declaration of conformty-------------------------------------------------------------------------------3
2 Technical data----------------------------------------------------------------------------------------------
4
3 Fundamental information (general)-----------------------------------------------------------------
4
3.1 Intended use-------------------------------------------------------------------------------------------
4
3.2 Inappropriate use-------------------------------------------------------------------------------------
4
3.3 Guarantee----------------------------------------------------------------------------------------------
5
3.4 Monitoring the test substances -------------------------------------------------------------------
5
4 Fundamental safety information---------------------------------------------------------------------
5
4.1 Observe the information in the operating instructions --------------------------------------
5
4.2 Staff training-------------------------------------------------------------------------------------------
5
5 Transport and storage-----------------------------------------------------------------------------------
5
5.1 Acceptance check------------------------------------------------------------------------------------
5
5.2 Packaging----------------------------------------------------------------------------------------------
5
6 Unpacking, installation and commissioning-----------------------------------------------------
6
6.1 Place of installation, place of use ----------------------------------------------------------------
6
6.2 Unpacking----------------------------------------------------------------------------------------------
7
6.2.1 Installation ------------------------------------------------------------------------------------------
7
6.2.2 List of items supplied-----------------------------------------------------------------------------
7
6.3 Battery operation and change---------------------------------------------------------------------
7
6.4 Initial start-up------------------------------------------------------------------------------------------
7
6.5 Adjustment---------------------------------------------------------------------------------------------
7
6.6 Adjusting------------------------------------------------------------------------------------------------
8
7 Operation ----------------------------------------------------------------------------------------------------
8
7.1 Overview of display (Units on display)----------------------------------------------------------
8
7.1.1 Weighing --------------------------------------------------------------------------------------------
8
7.1.2 Taring ------------------------------------------------------------------------------------------------
9
7.1.3 Plus/Minus Weighings ---------------------------------------------------------------------------
9
7.1.4 Net-total weighings -------------------------------------------------------------------------------
9
7.1.5 Unit change---------------------------------------------------------------------------------------
10
8 Maintenance, upkeep, disposal --------------------------------------------------------------------
10
8.1 Cleaning ----------------------------------------------------------------------------------------------
10
8.2 Maintenance, upkeep -----------------------------------------------------------------------------
10
8.3 Disposal ----------------------------------------------------------------------------------------------
10
9 Troubleshooting-----------------------------------------------------------------------------------------
11
TEB-BA-e-0510
3
1 Declaration of conformty
Declaration of Conformity
The electronic pocket balance
Type: KERN TEB 200-1
correspond to the following EC requirements:
EC-EMC-directive version 89/336/EEC
Compatible norms are, in particular
Standards for electronic scale.
EN 61000-6-3 :2001
EN 61000-6-1 :2001
If a change is made to the above mentioned appliances without consulting KERN
this declaration will become invalid
Date: 01.10 2005 Signature:
Gottl. KERN & Sohn GmbH
Management
Gottl. KERN & Sohn GmbH, Ziegelei 1, 72336 Balingen-Frommern, Tel. 07433/9933-0, Fax 07433/9933-149
TEB-BA-e-0510
4
2 Technical data
KERN TEB200-1
Readout (d) 0,1 g
Weighing range (max) 200 g
Taring range (subtractive) 200 g
Adjusting weight 100 g (M3)
Optimal temperature range 18 – 25 °C
Units g / tol / tlt
Permissible relative humidity < 85 %(non-condensing)
Weighing plate mm 70 x 80
Size (B x H x T) mm 85 x 130 x 25
3 Fundamental information (general)
3.1 Intended use
The balance you have acquired serves to determine the weighing value of the material to be weighed. It is intended to be used as a “non-automatic“ balance, i.e. the
material to be weighed is manually and carefully placed in the centre of the weighing
plate. The weighing value can be read off after a stable weighing value has been obtained.
3.2 Inappropriate use
Do not use the balance for dynamic weighing. In the event that small quantities are
removed or added to the material to be weighed, incorrect weighing results can be
displayed due to the “stability compensation“ in the balance. (Example: Slowly draining fluids from a container on the balance.)
Do not leave a permanent load on the weighing plate. This can damage the measuring equipment.
Be sure to avoid impact shock and overloading the balance in excess of the prescribed maximum load rating (max.), minus any possible tare weight that is already
present. This could cause damage to the balance.
Never operate the balance in hazardous locations. The series design is not explosion-proof.
Structural alterations may not be made to the balance. This can lead to incorrect
weighing results, faults concerning safety regulations as well as to destruction of the
balance.
The balance may only be used in compliance with the described guidelines. Varying
areas of application/planned use must be approved by KERN in writing.
Loading...