Page 1
ODC-82_83-BA-e-1610
KERN & Sohn GmbH
Ziegelei 1
D-72336 Balingen
E-Mail: info@kern-sohn.com
Tel: +49-[0]7433- 9933-0
Fax: +49-[0]7433-9933-149
Internet: www.kern-sohn.com
User instructions
Microscope camera
KERN
ODC-82, ODC-83
ODC 822, ODC 824, ODC 825
ODC 831, ODC 832
Version 1.0
01/2016
Page 2
2
ODC-82_83-BA-e-1610
Model
KERN
Resolution
Interface
Sensor
Frame rate
Colour /
Monochrome
Supported operating
systems
ODC 822
1,3 MP
USB 2.0
1/3“ CMOS
15 - 48 fps
Colour
Win, XP, Vista, 7, 8, 10
ODC 824
3,1 MP
USB 2.0
1/2“ CMOS
11,5 - 45 fps
Colour
Win, XP, Vista, 7, 8, 10
ODC 825
5,1 MP
USB 2.0
1/2,5“ CMOS
6,8 -55 fps
Colour
Win, XP, Vista, 7, 8, 10
ODC 831
3,1 MP
USB 3.0
1/3“ CMOS
27,3 – 53,3 fps
Colour
Win, XP, Vista, 7, 8, 10
ODC 832
5,1 MP
USB 3.0
1/2,5“ CMOS
14,2 – 101,2
Colour
Win, XP, Vista, 7, 8, 10
GB
KERN ODC-82, ODC-83
Version 1.0 01/2016
User instructions
Microscope camera
Before use
You should ensure that the device is not exposed to direct sunlight, temperatures which
are too high or too low, vibrations, dust or a high level of humidity.
The ideal temperature range is between 0 and 40°C and a relative humidity of 85%
should not be exceeded.
Always make sure that you use an approved power cable. Thus possible damages by
reason of the development of overheating (fire hazard) or an electric shock can be
prevented.
Do not open the housing and touch the internal component. There is the risk of
damaging them and affecting the functionality of the camera.
In order to carry out cleanings always disconnect the power cable from the camera.
Always keep the sensor clear from dust and do not touch it. Otherwise there is the risk
of affecting the microscopic image. In case of non-use always attach the protective
covers.
Technical data
Page 3
ODC-82_83-BA-e-1610
3
Scope of delivery
- Microscope camera
- USB cable
- Object micrometre for calibration
- Software CD
- Eyepiece adapter (Ø 23,2 mm)
- Adjustment rings (Ø 30,0 mm + Ø 30,5 mm) for eyepiece adapter
Mounting
1. Unscrew the black cover at the bottom of the camera.
2. The thread, where the cover was attached, is a standardised C
mount thread. Thus there are special C mount adapter needed for
the connection to a microscope.
3. For the mounting to the microscope the C mount adapter is
attached to the connection point of the microscope. After that the
camera has to be screwed onto the C mount adapter.
Important:
The choosing of the right C mount adapter depends on the used
microscope model. It has to be an adapter, which is adjusted to
the construction of the microscope and recommended by the
manufacturer as appropriate for the relevant microscope.
4. If necessary, adjust the microscope according to the trinocular
usage (with help of the trino toggle rod / trino toggle wheel).
PC connection
1. Establish USB connection via USB cable.
2. Installing the software with help of the CD.
Detailed instructions can be found in the supplied "readme"-file.
3. Both the supplied "Help"-files and the software-internal "User
Guide" include all information and instructions about the operation
of the software or of digital microscopy.
Loading...