10 Instant help ..................................................................................................... 7
MGD-BA-e-1710
3
1 Technical data
KERN MGD 100K-1 MGD 200K-1L
Readability (d) 0.1 kg 0.1 kg
Weighing range (max) 180 kg 250 kg
Accuracy +- 0.5% +- 0.1kg
Height of digits (mm) 40 50
Weighing Units kg, lb
Stabilization time 2 sec.
Operating temperature
Humidity of air
Battery
Operating period: 100 h
Dimensions (B x D x H)
mm
Material weighing
platform
Weight kg (net) 1.5 2.0
2 x CR2032
Auto-Off: 10 sec.
300 x 300 x 19 380 x 330 x 27
-10° C …. + 40° C
max. 80 % (not condensing)
3 x 1.5 V AAA
Operating period: 100 h
Auto-Off: 10 sec.
Glass
2 Declaration of conform ity
The current EC/EU Conformity declaration can be found online in:
www.kern-sohn.com/ce
MGD-BA-e-1710
4
3 Basic Information (General)
3.1 Proper use
This balance is used to calculate the weight of people in the private sphere.
Utilisation of this balance in the medical field is not permissible.
The weighing process requires that the person stands on the weighing plate in a way
that provides even weight distribution over the entire weighing plate. As soon as a
stable weighing value is reached the weighing value can be read.
3.2 Improper Use
Do not leave permanent load on the weighing pan. This may damage the measuring
mechanism.
Take care to avoid impacts and overloading of balance above the specified maximum
load (max) under all circumstances. This could cause damage to the balance.
Never operate balance in explosive environment. The serial version is not explosion
protected.
The structure of the balance may not be modified. This may lead to incorrect
weighing results, safety-relat ed faul ts and destruction of the balance.
The balance may only be used according to the described conditions. Other areas of
use must be released by KERN in writing.
3.3 Warranty
Warranty claims shall be voided in case
Our conditions in the operation manual are ignored
The appliance is used outside the described us es
The appliance is modified or opened
Mechanical damage and damage caused by media, liquids
Natural wear and tear
The appliance is improperly set up or incorrectly electrically connected
The measuring system is overloaded
Dropping the balance
4 Basic Safety Precautions
4.1 Pay attention to the instructions in the Operation Manual
Attention:
Stepping on the edge of the weighing plate may cause tilting of balance or fall of
person.
Carefully read this operation manual before setup and
commissioning, even if you are already familiar with KERN balances.
MGD-BA-e-1710
5
5 T ransport and storage
5.1 Testing upon acceptance
When receiving the appliance, please check packaging immediately, and the
appliance itself when unpacking for possible visible damage.
5.2 Packaging
Keep all parts of the original packaging in case you need to return the appliance.
Only use original packaging for returning.
6 Unpacking, Setup and Commi s si oning
6.1 Installation Site, Location of Use
The balances are designed in a way that reliable weighing results are achieved in
common conditions of use.
You will work accurately and fast, if you select the right location for your balance.
Therefore, observe the following for the installation site:
- Place the balance on a firm, level surface;
- Avoid extreme heat as well as temperature fluctuation caused by installing
next to a radiator or in the direct sunlight;
- Protect the balance against direct draughts due to open windows and doors;
- Avoid jarring during weighing;
- Protect the balance against high humidity, vapours and dust;
- Do not expose the device to extreme dampness for longer periods of time.
Non-permitted condensation (co ndensation of air humidity on the appliance)
may occur if a cold appliance is taken to a considerably warmer environment.
In this case, acclimatize the appliance for ca. 2 hours at room temperature.
- Avoid static charge of the balance and of the person to be weighed.
- Avoid contact with water.
The occurrence of electric fields or electrostatic charge may result in major display
deviations (incorrect weighing results). In that case, the location must be changed.
6.2 Unpacking
Take the whole balance out of their packaging and place them at the intended
position. In addition to the scales, delivery also includes operating instructions.
6.3 Battery operation
“LO“ on the display indicates that the battery load status is low. Replace batteries as
quickly as possible with a new set.
If the balance is not used for a longer time, take out the batteries and store them
separately. Leaking battery liquid could damage the balance.
MGD-BA-e-1710
6
7 Using the balance
The weighing process requires that the person stands on the weighing plate in
a way that provides even weight distribution over the entire weighing plate.
The display will be flashing during the weighing process.
When the weighing value is stable, the weight of the person can be read.
The weighing value will be shown for approx. 10 seconds, after which the
scales will turn off automatically.
Remark: The typical weight of a person will vary over the day, and equally from one
day to the next. Minor weight variations are considered normal.
8 Servicing, maintenance, disposal
8.1 Cleaning
Do not use aggressive cleaning agents (solvents or similar) but only a damp cloth
with mild soapsuds, or household cleaner. Ensure that no liquid gets inside the unit
and rub with a soft, dry cloth.
Loose dirt can be removed carefully with a brush or hand-held vacuum cleaner.
Balance must not be tilted or rotat ed for clea ning, as damage may occur.
Remove dirt immediately.
8.2 Servicing, maintenance
The appliance may only be opened by trained service technicians who are authorized
by KERN.
8.3 Disposal
Disposal of packaging and appliance must be carried out by operator according to
valid national or regional law of the location where the appliance is used.
MGD-BA-e-1710
7
9 Error message
The displayed weight is
• Table/floor vibrations
• Weighing plate has contact with other objects
possible)
The weighing result is
obviously incorrect
• Great fluctuations in temperature.
possible)
“Err“ on the display indicates that the weighing range has been exceeded. Please
take the weight off the scales.