KEPCO RKW-150P User Manual

INSTRUCTION MANUAL

KEPCO

An ISO 9001 Company.

KIT

DIN RKW-150P

DIN-RAIL MOUNTING KIT

FOR SERIES RKW 150W

DESCRIPTION. Kepco KIT, Model DIN RKW-150P contains a cover, a mounting bracket with left and right preassem-

bled mounting clips and associated hardware used to install RKW Series power supplies on a DIN rail. The “P” suffix is
for mounting the power supply perpendicular to the DIN rail as shown in Figure 1. Outline Dimensions are shown in
Figure 5

FIGURE 1. P SUFFIX ORIENTATION

TABLE 1. COMPONENTS SUPPLIED

SCREW

KIT

MODEL NO.

DIN RKW-150P CA 36 128-2124

KEPCO, INC. " 131-38 SANFORD AVENUE " FLUSHING, NY. 11352 U.S.A. " TEL [phone] " FAX [phone]

©2003, KEPCO, INC
Data subject to change without notice 228-1457

COVER

PART

NO.

MOUNTING

BRACKET

PART NO.

http://www.kepcopower.com "

(QTY 7)

(Power Supply

To Mounting

Bracket)

PART NO.

501-0075

(M4 x 8 FHPH)

WAS HE R

(QTY 7)

(Power Supply

To Mounting

Bracket)

PART NO.

103-0017

(NO. 8, INT.

TOOTH)

email: [e-mail]

CLIP

(QTY 2)

PART

NO.

108-0362 128-1938

CLIP

PLATE

(QTY 2)

PART

NO.

SCREW

Thread form

(QTY 4)

(Clip To

Mounting

Bracket)

PART NO.

101-0443

(4-40 X 1/4

BHPH)

WASHER

(QTY 4)

(Clip To

Mounting

Bracket)

PART NO.

103-0014

(NO. 4, INT.

TOOTH)

1

INSTALLATION

1. INSTALL COVER. Attach the cover to the power supply per instruction manual supplied with the cover.

2. INSTALL MOUNTING BRACKET. Attach the mounting bracket to the power supply using the hardware
supplied (see Figure 2).

FIGURE 2. INSTALLING MOUNTING BRACKET ON POWER SUPPLY

3. INSTALL CLIPS. Attach preassembled mounting clips into the mounting bracket holes using hardware
supplied (see Figure 3).

FIGURE 3. INSTALLING CLIPS ON MOUNTING BRACKET

KEPCO, INC. " 131-38 SANFORD AVENUE " FLUSHING, NY. 11352 U.S.A. " TEL [phone] "

2

http://www.kepcopower.com " email: [e-mail]

228-1457 031103

FAX [phone]

4. INSTALL POWER SUPPLY ON DIN RAIL. To mount the power supply on the rail insert one end of both
mounting clips under one edge of the rail, then snap the other end of the two clips into place (see Figure 4A).

INSTALLATION

A

B

REMOVAL

FIGURE 4. INSTALLATION AND REMOVAL OF POWER SUPPLY FROM DIN RAIL

REMOVING POWER SUPPLY FROM DIN RAIL. While grasping the power supply with one hand, Insert a screw-

driver into the access holes provided and apply leverage towards the left as shown in Figure 4B to disengage each clip
from the rail. Where mounting clips are close together, it may be necessary to apply leverage with two screwdrivers
simultaneously.

KEPCO, INC. " 131-38 SANFORD AVENUE " FLUSHING, NY. 11352 U.S.A. " TEL [phone] "

http://www.kepcopower.com " email: [e-mail]

031103 228-1457

FAX [phone]

3

FIGURE 5. RKW, 150W POWER SUPPLY WITH KIT INSTALLED, OUTLINE DIMENSIONS

KEPCO, INC. " 131-38 SANFORD AVENUE " FLUSHING, NY. 11352 U.S.A. " TEL [phone] "

4

http://www.kepcopower.com " email: [e-mail]

228-1457 031103

FAX [phone]