KEPCO FAW-150P User Manual

INSTRUCTION MANUAL

KEPCO

An ISO 9001 Company.

KIT

DIN FAW

-100P, -150P

DIN-RAIL MOUNTING KIT

FOR SERIES FAW 100W, 150W

DESCRIPTION. Kepco KITs, Models DIN FAW-100P, and -150P each contain a cover, a mounting bracket with left and

right preassembled mounting clips and associated hardware used to install FAW Series power supplies on a DIN rail.
The -100 suffix is for the 100 Watt Series and -150 for the 150 Watt Series. The “P” suffix is for mounting the power
supply perpendicular to the DIN rail as shown in Figure 1. Outline Dimensions are shown in Figure 5

FIGURE 1. P SUFFIX ORIENTATION

TABLE 1. COMPONENTS SUPPLIED

SCREW

KIT

MODEL NO.

DIN FAW-100P CA 27 128-1952

DIN FAW-150P CA 28 128-1953

KEPCO, INC. " 131-38 SANFORD AVENUE " FLUSHING, NY. 11352 U.S.A. " TEL [phone] "

©1998, KEPCO, INC
Data subject to change without notice 228-1314

COVER

PART

NO.

MOUNTING

BRACKET

PART NO.

http://www.kepcopower.com " email: [e-mail]

(QTY 6)

(Power Supply

To Mounting

Bracket)

PART NO.

101-0092

(4-40 X 5/16

BHPH)

101-0092

(4-40 X 5/16

BHPH)

WASHER

(QTY 6)

(Power Supply

To Mounting

Bracket)

PART NO.

103-0014

(NO. 4, INT.

TOOTH)

103-0014

(NO. 4, INT.

TOOTH)

CLIP

(QTY 2)

PART

NO.

108-

0362

108-

0362

CLIP

PLATE

(QTY 2)

PART

NO.

128-1938

128-1938

SCREW

Thread form

(QTY 4)

(Clip To

Mounting

Bracket)

PART NO.

101-0443

(4-40 X 1/4

BHPH)

101-0443

(4-40 X 1/4

BHPH)

FAX [phone]

WAS HE R

(QTY 4)

(Clip To

Mounting

Bracket)

PART NO.

103-0014

(NO. 4, INT.

TOOTH)

103-0014

(NO. 4, INT.

TOOTH)

1

INSTALLATION

1. INSTALL COVER. Attach the cover to the power supply per instruction manual supplied with the cover.

2. INSTALL MOUNTING BRACKET. Attach the mounting bracket to the power supply using the hardware
supplied (see Figure 2).

FIGURE 2. INSTALLING MOUNTING BRACKET ON POWER SUPPLY

3. INSTALL CLIPS. Attach preassembled mounting clips into the mounting bracket holes using hardware
supplied (see Figure 3).

FIGURE 3. INSTALLING CLIPS ON MOUNTING BRACKET

KEPCO, INC. " 131-38 SANFORD AVENUE " FLUSHING, NY. 11352 U.S.A. " TEL [phone] "

2

http://www.kepcopower.com " email: [e-mail]

228-1314 061901

FAX [phone]

4. INSTALL POWER SUPPLY ON DIN RAIL. To mount the power supply on the rail insert one end of both
mounting clips under one edge of the rail, then snap the other end of the two clips into place (see Figure 4A).

INSTALLATION

A

B

REMOVAL

FIGURE 4. INSTALLATION AND REMOVAL OF POWER SUPPLY FROM DIN RAIL

REMOVING POWER SUPPLY FROM DIN RAIL. While grasping the power supply with one hand, Insert a screwdriver

into the access holes provided and apply leverage towards the left as shown in Figure 4B to disengage each clip from
the rail. Where mounting clips are close together, it may be necessary to apply leverage with two screwdrivers simul­taneously.

KEPCO, INC. " 131-38 SANFORD AVENUE " FLUSHING, NY. 11352 U.S.A. " TEL [phone] "

http://www.kepcopower.com " email: [e-mail]

061901 228-1314

FAX [phone]

3

FIGURE 5. FAW 100W, 150W POWER SUPPLY WITH KIT INSTALLED, OUTLINE DIMENSIONS

KEPCO, INC. " 131-38 SANFORD AVENUE " FLUSHING, NY. 11352 U.S.A. " TEL [phone] "

4

http://www.kepcopower.com " email: [e-mail]

228-1314 061901

FAX [phone]