KEPCO FAK-50P User Manual

INSTRUCTION MANUAL

KEPCO

An ISO 9001 Company.

KIT

DIN FAK

-15P, -25P, 50P

DIN-RAIL MOUNTING KIT

FOR SERIES FAK 15W, 25W, 50W

DESCRIPTION. Kepco KITs, Models DIN FAK-15P, -25P, and -50P each contain a cover, a mounting bracket with left

and right preassembled mounting clips and associated hardware used to install FAK Series power supplies on a DIN
rail. The -15 suffix is for the 15 Watt Series, -25 for the 25 Watt Series and -50 for the 50 Watt Series. The “P” suffix is
for mounting the power supply perpendicular to the DIN rail as shown in Figure 1. Outline Dimensions are shown in
Figures 5 (-15P and -25P) and 6 (-50P).

FIGURE 1. P SUFFIX ORIENTATION

TABLE 1. COMPONENTS SUPPLIED

SCREW

KIT

MODEL NO.

DIN FAK-15P CA 21 128-1945

DIN FAK-25P CA 22 128-1975

DIN FAK-50P CA 23 128-1974

KEPCO, INC. " 131-38 SANFORD AVENUE " FLUSHING, NY. 11352 U.S.A. " TEL [phone] "

©1998, KEPCO, INC
Data subject to change without notice 228-1316

COVER

PART

NO.

MOUNTING

BRACKET

PAR T N O .

http://www.kepcopower.com " email: [e-mail]

(QTY 3)

(Power Supply

To Mounting

Bracket)

PART NO.

101-0092

(4-40 X 5/16

BHPH)

101-0092

(4-40 X 5/16

BHPH)

101-0092

(4-40 X 5/16

BHPH)

WAS HE R

(QTY 3)

(Power Sup-

ply To Mount-

ing Bracket)

PART NO.

103-0014

(NO. 4, INT.

TOOTH)

103-0014

(NO. 4, INT.

TOOTH)

103-0014

(NO. 4, INT.

TOOTH)

CLIP

(QTY 2)

PART

NO.

108-0366 128-1971

108-0366 128-1971

108-0362 128-1938

CLIP

PLATE

(QTY 2)

PART NO.

SCREW

Thread-form

(QTY 4)

(Clip To

Mounting

Bracket)

PAR T N O .

101-0443

(4-40 X 1/4

BHPH)

101-0443

(4-40 X 1/4

BHPH)

101-0443

(4-40 X 1/4

BHPH)

FAX [phone]

WASHER

(QTY 4)

(Clip To

Mounting

Bracket)

PART NO.

103-0014

(NO. 4, INT.

TOOTH)

103-0014

(NO. 4, INT.

TOOTH)

103-0014

(NO. 4, INT.

TOOTH)

1

INSTALLATION

1. INSTALL COVER. Attach the cover to the power supply per instruction manual supplied with the cover.

2. INSTALL MOUNTING BRACKET. Attach the mounting bracket to the power supply using the hardware
supplied (see Figure 2).

FIGURE 2. INSTALLING MOUNTING BRACKET ON POWER SUPPLY

3. INSTALL CLIPS. Attach preassembled mounting clips into the mounting bracket holes using hardware
supplied (see Figure 3).

FIGURE 3. INSTALLING CLIPS ON MOUNTING BRACKET

KEPCO, INC. " 131-38 SANFORD AVENUE " FLUSHING, NY. 11352 U.S.A. " TEL [phone] "

2

http://www.kepcopower.com " email: [e-mail]

228-1316 061901

FAX [phone]

4. INSTALL POWER SUPPLY ON DIN RAIL. To mount the power supply on the rail insert one end of both
mounting clips under one edge of the rail, then snap the other end of the two clips into place (see Figure 4A).

INSTALLATION

A

B

REMOVAL

FIGURE 4. INSTALLATION AND REMOVAL OF POWER SUPPLY FROM DIN RAIL

REMOVING POWER SUPPLY FROM DIN RAIL. While grasping the power supply with one hand, Insert a screwdriver

into the access holes provided and apply leverage towards the left as shown in Figure 4B to disengage each clip from
the rail. Where mounting clips are close together, it may be necessary to apply leverage with two screwdrivers simul­taneously.

KEPCO, INC. " 131-38 SANFORD AVENUE " FLUSHING, NY. 11352 U.S.A. " TEL [phone] "

http://www.kepcopower.com " email: [e-mail]

061901 228-1316

FAX [phone]

3

FIGURE 5. FAK 15W, 25W POWER SUPPLY WITH KIT INSTALLED, OUTLINE DIMENSIONS

FIGURE 6. FAK 50W POWER SUPPLY WITH KIT INSTALLED, OUTLINE DIMENSIONS

KEPCO, INC. " 131-38 SANFORD AVENUE " FLUSHING, NY. 11352 U.S.A. " TEL [phone] "

4

http://www.kepcopower.com " email: [e-mail]

228-1316 061901

FAX [phone]