SIROCCO VENTILATION HOOD
OWNER’S GUIDE
READ AND SA VE THESE INSTRUCTIONS
Models: B81200 Series
Important Safety Instructions
Take care when using cleaning agents or detergents.
Select products suitable for use in household cooking area only.
Certain locales require make-up air calculations for total airflow.
Consult your local codes and an HVAC professional before installing or using this hood.
CAUTION - To reduce risk of fire and to properly exhaust air, be sure to duct air outside – Do not vent exhaust air into
spaces within walls or ceilings or into attics, crawl spaces, or garages.
CAUTION - For General Ventilating Use Only. Do Not Use To Exhaust Hazardous Or Explosive Materials And Vapors.
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.
b. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the service panel.
WARNING – TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
b. Always turn hood ON when cooking at high heat or when cooking flaming foods.
c. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.
d. Use proper pan size. Always use cookware appropriate for the size of the surface element.
WARNING – TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE,
OBSERVE THE FOLLOWING:
a. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO
PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
b. NEVER PICK UP A FLAMING PAN – You may be burned.
c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.
d. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate it.
2. The fire is small and contained in the area where it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit.
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a) Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and
standards, including fire-rated construction.
b) Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning
equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such
as those published by the National Fire Protection Association (NFPA), and the American Society for Heating,
Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
c) When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
d) Ducted fans must always be vented to the outdoors.
WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
WARNING - Electrical Shock Hazard - Can result in serious injury or death. Disconnect appliance from electric power
before servicing. If equipped, the fluorescent light bulb contains small amounts of mercury which must be recycled or disposed
of according to Local, State, and Federal Codes.
r
Installation
FOR RESIDENTIAL USE ONLY
NOT TO BE INSTALLED OVER GAS GRILLS
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.
INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.
IMPORTANT: Save these Instructions for the Local Electrical Inspector’s use.
INSTALLER: Please leave these Instructions with this unit for the owner.
OWNER: Please retain these instructions for future reference.
SAFETY WARNING: Turn off power circuit at the service entrance and lock out panel, before wiring this appliance.
REQUIREMENT: 120 V AC, 60 Hz. 15 or 20 Amp
Dimensions
Cabinet Front View
Fixing
Point 1
Fixing
Point 2
24” - 30” - 36”
Cabinet Top View
Internal Width
1
/
" (24" Model)**
22
16
7
28
/
" (30" Model)**
16
7
34
/
" (36" Model)**
3
1
/
"
4
3
max
13
/
" *
16
13
/
min 10
" *
16
Cut-Out for
1/2" Conduit
* Do not consider the door of the cabinet
** Use spacers for 1/4" wider cabinet
Cabinet Right/Left Side View
Cabinet
Door
Fixing
Point 1
Fixing
Point 2
16
Rearside of the Cabinet/Hood
C
7
3
/
L
16
min Depth of
Recessed
1
7
/
Area =
"
2
6"
1
5
/
"
16
"
3
3
/
8
11
/
16
9
15
/
16
Fixing
Point 1
Fixing
Point 2
2
Cut-Out fo
5" Duct
Cabinet
Door
min Height
of Recessed
Area =
"
1
4
/
16
"
Before Installing Hood
1.This hood is designed to be mounted flush to the rear wall (to
avoid clearance from wall to hood) and to the internal sides of
cabinet (where hood must be fixed); for this reason we
suggest installing this hood only inside a cabinet having an
"
internal width of 22
36” Model and with an internal depth of minimum 7
The external depth of the cabinet must be minimum 10
maximum 13
Attention! Do not consider the door of the cabinet when
measuring.
The appliance is also supplied with 4 spacers that can be
snapped at fixing point 1 and 2 , cabinets
used, see figure 2.
2. For the most efficient air flow exhaust, use a straight run or as few
elbows as possible.
CAUTION: Vent unit to outside of building ONLY.
3. If allowed in your area, use metallic flex ducting only to connect rigid
13
/
"
16
duct directly to transitions.
4. COLD WEATHER installations should have an additional backdraft
damper installed to minimize backward cold air flow and a nonmetallic
thermal break to minimize conduction of outside temperatures as
part of the ductwork. The damper should be on the cold air side of
the thermal break. The break should be as close as possible to
where the ducting enters the heated portion of the house.
A non-return smoke damper is supplied mounted on the transition.
5. Hood installation height above cooktop is at the users preference.
The lower the hood above the cooktop, the more efficient the
capturing of cooking odors, grease and smoke. We recommend that
the hood be installed 18” to 36” over an electric cooktop and 25” to
36” over a gas cooktop . Be sure that your hood model fits your
installation.
15
3
/
16
Basic Installation Steps
"
For easiest installation, the hood should be installed in the cabinet
before mounting the cabinet to the wall. In any case the installation
"
steps do not change.
1
/
” for the 24” Model, 28
16
3
/
”. See figure 1.
16
7
/
” for the 30” Model, 34
16
1
/
” . See figure 1.
2
1
/
” wider can be
4
13
7
/
16
/
16
” for the
” and
Figure 1
Spacer Pin
Spacer
for 1/4
wider
cabinet
Figure 2
13
/
16
13
"
10
/
"
16
11
17
/
"
16
Pin Housing
Motor Housing
Fixing Points 1-2
Snap Spacer
Pins Into Their
Housings
Tools required for installation
Screw driver (philips # 1 )
Electric drill
with twist bit
5
/
64
” and
7
15
/
” or
/
32
”
64
Tape
This Hood can easily be installed following these basic steps:
• Prepare the cabinet (cut out bottom and top of the cabinet as
required and mark fixing points)
• Run conduit and duct sections to the hood and make connections
• Fix the hood to the cabinet
• Mount the cabinet on the wall
• Connect duct to the outside and conduit section to the service panel
3
Installation
max
13 3/16" *
min 10 13/16" *
Figure 3
1
22
/
" (24" Model)**
16
7
28
/
" (30" Model)**
16
7
34
/
" (36" Model)**
16
Rearside of the Cabinet***
Cabinet
Door
7 1/2"
CUT-OUT
C
L
* Do not consider the Door of the Cabinet
4
/16"
** Add
when using Spacers
*** Rearside of the Cut-Out for cabinet deeper
13 3/16" (without considering the door)
than
Cabinet
Door
Prepare the cabinet for installation
• Mark and cut-out the cabinet bottom as shown in figure 3.
• Fit the template, which comes with the hood, on the inner
right side of the cabinet making sure the side with arrows
matches with the lower edge of the cabinet and the rear edge
of the cabinet or cut-out.
• Drill 2 holes 5/64” (see figure 4 - fixing point 1 and 2) and 1 blind
hole 15/64” in diameter, 13/64” in depth.
• Move template to the other side and repeat.
• Make cut-out for duct and conduit, see figure 1.
Fixing
point 1-2
Template
Backside of
the cabinet
Figure 4
Figure 5
cutout for
1/2" Conduit
and 5" Duct
Backside
border
Blind hole
(Side Springs
Housing)
Fixing
point 1-2
Template
Bottom of
the cabinet
Prepare the hood for installation
• Remove the hood from packaging, check its condition and
make sure the following pieces are included:
1 hood,
1 registration card
1 instruction manual
1 template
1 transition with damper
1 plastic bag with 4 hood fixing screws + 1 transition fixing
screw and 4 spacers.
• Remove the light shield, unscrew and remove lamps to
prevent damage when installing (see paragraph on “Light
replacement” for details).
• Pull out the slider and remove the grease filters (see paragraph
“To remove the grease filters” for details).
• Fit the transition on the outlet hole of the hood:
This has a bayonet lock and must be fixed to the hood with
one screw (Figure 5), check the opening and closing of the
damper mounted inside.
4
Installation
Cabinet
Side Spring
Figure 6
Side Spring
Install the Hood
• Set the motor housing into the opening.
• Push the spring inside the motor housing using a screw driver
as a lever from the inside of the motor housing.
• Insert it completely in place taking care to snap sides springs
into the blind holes made for temporary fixing and that conduit
and duct section, if already fitted, run freely across the cutouts on top of the cabinet, see figure 6.
• Fix the hood permanently with two screws (4.5x16) per side
to be inserted frome the inside of the hood to the corresponding
side fixing points 1 and 2 drilled on the cabinet, see figure 7.
• Connect a 5” duct to the transition and seal with tape.
• Connect to power supply
Attention! While mounting the hood on the wall cabinet be
sure once the hood has been fastened, that the wiring
compartment is easily and safely accessible, in order to
make safety inspections and/or maintenance operations.
WARNING!
ELECTRICAL GROUNDING INSTRUCTIONS
THIS APPLIANCE IS FITTED WITH AN ELECTRICAL
JUNCTION BOX WITH 3 WIRES, ONE OF WHICH
(GREEN/YELLOW) SERVES TO GROUND THE
APPLIANCE. TO PROTECT YOU AGAINST ELECTRIC
SHOCK, THE GREEN/YELLOW WIRE MUST BE
CONNECTED TO THE GROUNDING WIRE IN YOUR
HOME ELECTRICAL SYSTEM, AND IT MUST UNDER
NO CIRCUMSTANCES BE CUT OR REMOVED.
Fixing
point 1-2
Template
Backside of
the cabinet
Figure 7
Conduit
Cabinet
Door
cutout for
1/2" Conduit
and 5" Duct
Backside
border
Blind hole
(Side Springs
Housing)
Fixing
point 1-2
Template
Bottom of
the cabinet
Warning: Turn off power circuit at the service panel before wiring
this unit.
120 VAC, 15 or 20 Amp circuit required.
a. Remove j-box cover as shown in Figure 8.
b. Remove the knockout and install the strain relief (conduit)
connector (1/2") in junction box.
c. Run 3 wires; black, white and green (#16 AWG) in 1/2"
conduit from service panel to junction box.
d. Connect black wire from service panel to black or red in
junction box, white to white and green to green-yellow. See
Figure 8.
e. Close junction box cover.
Figure 8
5
Figure 8
M
Box adjustment
The hood can be installed in cabinets with different depths (see
also figure 1 for details); however the front of the slider box must
always be flush with the front of the cabinet.
For alignment, adjust the back stops of the box.
For box adjustment, loosen screws M, slide the square plates
P
P as necessary, and tighten screws M (Figure 8).
Ensure that the drawer, when fully retracted, turns OFF all
power by acting positively on the rear microswitch.
Final installation steps
• Insert lamps in place.
• Fit the Lamp Shield.
• Fit the Grease Filters.
• Check all light bulbs to make sure they are secure in their
sockets, then turn power on in service panel and check lights
and blower operation per Use & Care section of this manual
and install filters.
• Make sure to leave this manual for the home owner.
6
Use and Care
Control Pad Functions
READ THE INSTRUCTIONS CAREFULLY BEFORE USING THE RANGE HOOD.
For satisfactory use of your hood, become familiar with the various functions
of the hood as described below
Air outlet
Motor
Housing
Light OFF
Light ON
4
1
2
Slider
0 3
1
0
Box
Very High Speed
Left Grease Filter
Handles
Lamp Shield
Right Grease
Filter
Handles
Grease
Filters
High Speed
Medium Speed
Low Speed
Blower OFF
Figure 7
Operating Instructions
The blower should be turned on for about 5 minutes before cooking in order to establish air currents upward through
the hood.
Use the low speeds for normal use and the higher speeds for strong odors or fumes.
Minimize cross drafts which will reduce the effectiveness of the hood.
7
Hood Cleaning
Figure 8
Be sure lights are cool before cleaning the hood.
To Clean Filters
• The metal grease filters will last forever.
They are made of anodized aluminum
• It is recommended that the filters be washed at least once a month; they
can be washed by hand or in the dishwasher.
• Drain water through edge holes and let each filter dry thoroughly before
replacing it.
To Remove The Metal Grease Filters
• Turn blower and lights off.
• Push simultaneously the two grease filter handles first upwards, then pull towards
the center and extract the filters Figure 8.
• To reinstall, reverse procedure.
Lights replacement
R
Q
G
To Clean Hood Surface
• For general care, wipe the outside of the white or black hood with sudsy water
or general kitchen household cleaners, rinse well and dry with clean soft cloth to
avoid water marks.
• Do not use abrasive products.
NOTE: Turn blower and lights off. Make sure the lights are cool. If new lights
do not operate be sure lights are inserted correctly before calling service.
• Remove the light shield Q by pushing simultaneously the two unlocking buttons
R (Figure 9); for safety reasons make sure to remove the light shield from its
suspension slides G.
Attention: When removing, handle the light shield by the glass.
• Pull out fluorescent tube and replace with Philips Type PL-S 9 Watt maximum.
• Refit the light shield.
Figure 9
8
91011
LI1QVB Ed. 05/02
Loading...