STEREO SYSTEM RACK
SRC-603©/ 663
ASSEMBLY INSTRUCTIONS
KENWOOD
KENWOOD CORPORATION
©PRINTED IN U.S.A. B61-0577-00(TOCABI)
R0343 \ '
IMPORTANT:------------------------------
• Before operating your new KENWOOD product, read through this assem-
•bly manual carefully to get the most out of it.
• Save this assembly instructions.
Before Assembling
• Be sure to check that all parts are accounted for before disposing of the
packing case.
• A Phillips screwdriver and a mallet are required for assembling.
• Be carefull not to damage the floor and rack.
------------------------------
-------------------
IMPORTANT SAFEGUARDS
ACautiOT : Read this page carefully to keep your safety.
Please reagl^ of the safety and operating instructions before operating this
unit. For b^^'esults, follow all warnings placed on the unit and adhere to the
operating and use instructions. These safety and operating instructions should
be retained for future reference.
1. Suffocation — After taking the unit out of the polyethylene bag, be sure
to dispose of the polyethylene bag out of the reach of children. Otherwise,
they may play with the bag, which couid cause hazard of suffocation.
Notes on Assembling
• During assembling, be sure to verify the numbers stamped on the boards.
• Mount the rear panel after assembling the side panel on the bottom shelf
at a right angle.
• When mounting the top shelf and kick plate on the side panel, use glue
for adhesive. Be sure to remove any excess glue before it dries.
• If the amplifier wobbles when its key switches are pressed, insert a woo
den dowel into the hole on the side panel and fix the rear of the amplifier.
Handling Precautions
• Tempered glass is used for the glass doors for providing sufficient strength.
However, pay attention not to apply excessive force or to scratch the doors.
Cracking or breaking of the glass may occur.
• When moving the cabinet, remove all the components from the rack be
fore carrying the cabinet. Also do not grasp the top shelf when carrying.
• To allow head radiation from the components, leave a space of 4 inches
between the cabinet and wall.
• Do not place the cabinet in a location subject to direct sunlight or near a
heater, an air-conditioner, or a place with high humidity.
o
4. Impact — Avoid placing the unit on an unstable surfacr "^stall it on a
horizontal surface not subject to excessive dirt or vibrat.wi-
5. Modification — Do not attempt to open or modify the unit, for this could
cause fire hazard or malfunction.
o
2. Water and moisture — Do not place a liquid container, such as a vase and
water basin, on the unit. Also avoid installing the unit in a place subject
to dampness.
3. Heat — Do not install the unit near a source of heat, such as a heater, or
under direct sunlight.
). Cleaning — Do not use thinner, benzine or alcohol. When cleaning the unit,
wipe with a soft, dry cloth.
7. Abnormal smell — In the event the unit generates smoke or abnormal smell,
immediately switch the power OFF and unplug the power cord. After this,
please contact your dealer or nearest service station as soon as possible.
POWER OFF!
' PARTS LIST MODEL SRC-603 © / 663 ©
ASSEMBLY INSTRUCTIONS
STEP 3
0
o
CTCD
O I Cr
A WOODGRAIN
H- SURFACES UP
AND FORWARD
STEP 5
CONTINUED NEXT PAGE
ASSEMBLY INSTRUCTIONS
MODEL: SRC-603©/663©
ITEM
DESCRIPTION QTY PAR
A
LEFT SIDE PANEL
B
BOTTOM BOARD
C
RIGHT SIDE PANEL
D
KICK PLATE
E
TOP BOARD
F
BACK BOARD A
G
SHELF A
H SHELF B
1
BACK BOARD B
- J
CONFIRMAT SCREW
K
SCREW
L
ALLEN WRENCH
M
HINGE INSERT
PARTS LIST
TNO.pjjiL,
SRC-603©
SRC-663©
1 ' XW0689
1 XW0692
1
XW0688
1 XW0497 '
1 _ XW0687 XW0674
1 XW0693
1 XW0690
1 XW069.1
1 XW0694
4 S0033
12 S0034
1 M0018
2
P0054 P0054
XW0676
XW0692
Xy^25, P
^^3W0511
XW0693 S GLUE 1
XW0690 T
XW0691
XW0694
S0035
S0034
M0018 Y
ITEM
DESCRIPTION QTY
N
MAGNET CATCH 1
0 SHELF PIN
RUBBER SPACER
Q WOOD DOWEL
R WOOD DOWEL 2
SHELF PIN
u UPPER HINGE
V
LOWER HINGE
w
CATCH PLATE
• X
CATCH PLATE PAD
GLASS DOOR
1
1
1
1
4
4
9
4
PART NÔ.
P0011
P0053
G0067
W0092
W0398
G0012
MODI 9
M0026
M0027
M0011
G0047
G0078
If any parts are MISS
ING or DAMAGED in
this package,circle the
item(s) needed on the
parts list. Print your
name, address, and
phone number in the
area to the left and mail
to:
TOCABI AMERICA,
9375 Custom House
Plaza Road, Suite I
San Ysidro, CA 92173,
or call (619)-661-6136.
Loading...