Kenwood RC-R0507 User Manual
Remote Control Instruction Manual
Quick start guide.......................................... 1
Getting the most from your remote control ........... 3
Setup code chart .......................................... 7
In case of difficulty ...................................... 13
Remote operation of other components ............. 14
Remote Control Instruction Manual
Preset Remote Control Quick Start Guide
4
2
3
POWER
SHIFTMACRO
AUDIO
P. CALL P. CALL
4¢
8
BAND
6
TVVIDEO
7
GUIDEREC
VOLUMETUNING/SKIP
MUTE
FUNCTION
SHIFT
LISTEN
MODE
THEME FAVMENU
INFO ALT AUDTV/SAT/VID
REPEAT RANDOM+100
DISPLAY
231
564
897
0
SOUNDSUBWOOFER
SETUP
ENT+10
1
This quick start guide explains how to setup the remote
control to operate audio and video components other
than the receiver.
In order to make full use of the functions of the remote
control, be sure to read the section of this manual
entitled “Getting the most from your remote control”.
It contains a detailed explanation of how to operate the
remote control and make the necessary settings.
The quick start guide describes the operation of the
following keys:
1 ENT key
Gets you into and out of the preset code registration
mode.
2 VIDEO, AUDIO, and TV keys
Use these keys to select the input you want to register.
3 Numeric keys
In the preset code registration mode, you use these
keys to enter the code numbers that let you control your
components.
4 POWER key
Once you have entered the setup code for another
component, you can press this key to turn power to that
component on or off. This lets you confirm that you
entered the code properly.
This instruction manual is for some models.
Model availability and features (functions) may differ depending on
the country and sales area.
REMOTE CONTROL UNIT
Remote Control
B60-3617-00 00 CS MA (T, E2, Q, X) ID
99/12 11 10 9 8 7 6 5 4 3 2 1 98/12 11 10 9 8 7 6 5 4 3 2
Register the setup codes for your audio and video components
2
Quick Start Guide
RC-R0507 (En/T)
Step 1
Look up the setup code for the component you want
to control. RC7
Write down all the applicable setup codes.
(This step is very important.)
Step 2
ENT
For step 2 through step 8, make sure you
start the next step within five seconds of
completing the previous one. If more than
five seconds elapses between any two
steps, you will need to go back and start
over from step 2.
Hold down ENT key until the backlight flashes twice (about three
seconds).
Step 5
Press the POWER key to see if you
POWER
If the component does not respond when you try to
control it, return to step 4 and enter the next setup
code on the list. Repeat this procedure until you find
the code that matches the component.
can turn the component on and
off. (If the component you want to
control has a mechanical power
key that cannot be operated by
remote control, press the PLAY
key or the TUNING/SKIP key to
test it.)
Step 6
ENT
Press the ENT key to store the
code.
Step 3
AUDIO
Step 4
DISPLAY
Remote Control
THEME FAVMENU
231
INFO ALT AUDTV/SAT/VID
564
REPEAT RANDOM+100
897
0
Press the VIDEO, AUDIO, or TV
TVVIDEO
key to select the input you want to
register. (Each press of the key
advances you one by one through
the available input settings.) The
current input setting appears on
the display of the receiver.
Use the numeric keys to enter the
4-digit setup code for the component.
Step 7
Repeat steps 3 though 6 to enter the codes for each
component you want to control.
Step 8
ENT
If you accidentally exit the registration mode by pressing
the wrong key, you will not lose any setup codes you have
already saved.
Once you have finished registering setup codes for all of the inputs, hold down ENT key until the
backlight flashes twice (about three
seconds).
This exists the registration mode.
Automatic input naming
In the initial factory setting, the remote control already has provisional component names registered for each input. Before you register setup codes,
pressing the input keys of the remote control causes the display to change from the factory preset input names of the receiver (VIDEO1, VIDEO2,
etc.) to the input names registered in the remote control (VCR1, VCR2, etc.). Once you have registered the appropriate setup codes for your
components, pressing the input keys of the remote control causes the display to change to the actually connected component names (LD, DVD,
etc.) for which you have registered setup codes.
Getting the most from your remote control
V
CR1
A
SP
SW
R
L
The remote control supplied with this receiver is also
capable of controlling components from a variety of manufacturers once you register the appropriate setup codes
into the remote control unit.
Refer to "Remote operation of other components" for details about the operations available for each component.
Low battery warning
Replace all four batteries with new ones when you notice a shortening
of the distance from which the remote control will operate or if the
remote control blinks 5 times when you press a key. The remote
control is designed to retain setup codes in memory while you
change batteries.
Registering setup codes for other components
POWER
VIDEO, AUDIO, TV
1-0
ENT
3
4
RC-R0507 (En/T)
Press the VIDEO, AUDIO, or TV key repeatedly to select
the desired component.
VIDEO key
1VIDEO1 (VCR1)
2VIDEO2 (VCR2)
3VIDEO3 (DVD)
or DVD 6ch
•Example : To register the component connected to the VIDEO 1
jacks, select "VIDEO 1 (VCR1)".
•On models other than the KRF-V8010D, “DVD 6ch” is displayed
instead of “VIDEO 3”. It is possible to enter a setup code for the
DVD 6ch input, but the display indication will remain “DVD 6ch”.
It is not possible to change the name of this input.
AUDIO key
1CD (CD)
2TAPE or MD
(TAPE)
3PHONO
TV key
1TV1
2TV2
3CABLE
Use the numeric keys to enter the setup code.
•Example: Press "5258" to register a LD player made by KENWOOD.
•The backlight flashes once each time a number is entered.
•If an invalid setup code is entered the remote will output one long
blink, disregard that code and return to the beginning of step 4.
•If you push an invalid key, the remote will exit the setup mode.
3
Find the setup code of the component to be registered.
1
• Refer to the setup code lists to find the setup code for the
component to be registered. RC7
Example: To register a CD made by KENWOOD, you would enter
"8028".
•When registering setup codes for KENWOOD audio components
which are connected to this unit by system control cords, use the
following codes to insure proper system control operation:
Cassette: 7000, CD: 8099, MD: 9000.
Input Component Maker Code Key
(CD) CD player KENWOOD 8028, 8037 AUDIO
TV 1
TV 2
CABLE
Hold down the ENT key until the backlight flashes twice.
2
•At this time all inputs become available regardless of any earlier
registration.
Press the POWER key, and check to see that the compo-
5
nent you want to control turns on.
If the component does not react, and there is more than one
setup code, enter another setup code and try again.
•PLAY, TUNING/SKIP (+/–) or MULTI CONTROL key can also be
used instead of POWER key.
•If the component is already on, pressing POWER key will turn it off.
Press the ENT key to store the code you have just input.
6
•The backlight flashes twice.
• This code replaces any previous setup codes entered for the
respective component.
Repeat steps 3 to 6 to register additional components
7
until all components have been registered.
•If you have components that are not remote controllable, like a
record player (etc.), you will need to register a Non-IR code at the
respective input. This keeps the respective input in the remote
control's cyclic list so you can select it using the remote control.
Please consult the owner's manual of the components you are
connecting for information regarding remote controllability. The list
of Non-IR codes is included at the beginning of the Setup code
chart.
Continued to next page
For step 2 through step 8, make sure you start the next step
within five seconds of completing the previous one. If more
than five seconds elapses between any two steps, you will
need to go back and start over from step 2.
Remote Control
4
SHIFT
VIDEO, AUDIO, TV
POWER
Once setup codes have been entered for all components,
8
hold down the ENT key until the backlight flashes twice.
•Once registered, the display on the receiver shows the component
type instead of the default input name.
Example: if you register a VCR at the VIDEO 1 jacks, "VCR" appears
instead of "VIDEO 1 (VCR1)".
•After initial setup, any VIDEO or TV (TV1, TV2, CABLE) inputs that
have not been programmed with a setup code or Non-IR code are
deleted from the cyclic list. The PHONO input will be deleted if a
Non-IR code was not registered.
•The INPUT SELECTOR on the front panel of the receiver always
cycles through all inputs.
Note
Although each setup code is designed to work with a number of
different models, certain codes may not work with some models.
(Also, certain codes may only operate some of the functions available
on a given model.)
Getting the most from your remote control
RC-R0507 (En/T)
Operating other components
This operation lets you operate the registered components.
KENWOOD audio components with system control turn on and off
automatically with the receiver via the system control connections.
Use the VIDEO, AUDIO, or TV keys to select the compo-
1
nent you desire.
•Pressing the VIDEO or AUDIO key also changes the input selector
on the receiver. If you do not want to change the current input,
press the SHIFT key before step 1. RC5
VIDEO key
1 VIDEO1 (VCR 1)
2 VIDEO2 (VCR 2)
3 VIDEO3 (DVD)
or DVD 6ch
4 Not used by this
remote control.
(<--->)
Press the SHIFT key and then press the POWER key
2
(within 3 seconds).
•Pressing the SHIFT key is only required when turning the selected
component on or off. Pressing the POWER key directy turns the
receiver on and off.
Press the operation keys you desire.
3
• See "Remote operation of other components" at the end of this
manual for a list of keys available with each component.
The remote control mode remains in the set at the component
selected in step 1 mode until you select another component
(etc.).
AUDIO key
1 CD (CD)
2 TAPE or MD
(TAPE)
3 TUNER
4 PHONO
TV key
1 TV1
2 TV2
3 CABLE
RC$
Remote Control
Note
Be sure to point the remote control at the remote sensor on the receiver
when you want to operate KENWOOD components connected by
system control cords. Otherwise, point the remote control at the
component you want to operate.
Getting the most from your remote control
RC-R0507 (En/T)
Changing (confirming) the operation mode
This operation lets you change the remote control operation mode
without changing the input selector.
You may find this useful when you want to control one component while
using another. (For example, if you want to rewind the tape deck while
listening to a CD.)
This operation is also useful if you don't know the which mode the
remote control is set to. Executing this operation allows you to change
or reconfirm the operation mode you desire.
VIDEO, AUDIO, TV
Press the SHIFT key.
1
•To operate a TV, start from step 2.
Go to step 2 within 3 seconds.
Press the VIDEO, AUDIO or TV key repeatedly to display
2
the remote control mode for the component you want to
control.
SP
A
R
L
SW
CD
The component to be controlled is displayed in parenthesis
SHIFT
Preparing for automatic operations
(MACRO play)
The macro play function allows you to set the remote to control several
components in succession. After completing this setup, you can
perform a series of operations automatically. Enter the setup codes for
the components you want to control beforehand.
VIDEO, AUDIO, TV
Make a plan of the macro play you want to Setup.
1
The order of the operations may be fairly complex and you may
not be remember all of the necessary commands during the
setup procedure.
Use the space provided below to write down the operations in
the order you are going to enter them.
1!
2@
3#
4$
5%
6^
7&
8*
9(
0)
MACRO
5
• Pressing any other keys after the SHIFT key cancels the shift
function and sends the normal code associated with the respective
key.
•The input selector does not change during this operation.
• If you press VIDEO or AUDIO key more than 3 seconds after
pressing the SHIFT key, the input selector changes together with
the operation mode.
Execute the desired operations.
3
• See "Remote operation of other components" for a list of keys
available with each component. RC$
The operation mode remains set at the component specified in
step 2.
To return control to the original component, press SHIFT and
then press the VIDEO or AUDIO key to return to the original
control mode.
•Up to 20 steps can be memorized for each macro.
•The example below shows the plan for step 4 (which occupies a
total of 9 steps) :
1 TV + SHIFT + POWER 3 steps
2 FUNCTION SHIFT + 4 2 steps
3 VIDEO + VIDEO 2 steps
4 SHIFT + POWER 2 steps
Total 9 steps
•If you attempt to store more than 20 steps, the remote will output
one long blink and exit the macro programming mode.
•Enter channel numbers (for the monitor TV, etc.) exactly as you
would using the original remote.
Press and hold the MACRO key until the backlight flashes
2
twice.
Perform each of the following steps within 5 seconds.
Press the VIDEO, AUDIO, or TV key to select the macro
3
location. (MACRO1, 2, and 3 respectively)
•You can store up to 3 different macros, one at each key:
VIDEO = "MACRO 1", AUDIO = "MACRO 2", TV = "MACRO 3"
•The backlight flashes once when you select the macro location.
•Pressing a key other than VIDEO, AUDIO, or TV cancels the macro
program mode.
When VIDEO is pressed
SP
A
R
L
SW
M
ACRO 1
Remote Control
Continued to next page
Loading...