Page 1
12.CAW1170-09
KENWOOD
Listen to the Future
VEHICLE APPLICATIONS
Mazda
2007-0a CX-7
Page 2
2007-08 MAZDA CX-7
DASH DISASSEMBLY AND RADIO REMOVAL INSTRUCTIONS
1. Carefully pull forward and remove the entire trim bezel from around the radio
and Climate controls.
2. Remove the (4) Phillips screws securing the radio to the sub-dash,
disconnect all attached harnesses and antenna lead and remove radio.
Hazard Switch Removal Instructions
f. Disconnect the harness attached to the back of the factory hazard switch.
2. Remove the (2) Phillips screws securing the Hazard switch to the rear
of the factory radio.
3. Remove the (4) Phillips screws securing the chassis of the factory radio
to the rear of the radio face and set aside the chassis.
4. Using a pick tool, or a jewelers flat blade screwdriver, carefully lift upward the back
top and bottom edge locking tabs securing the front portion of the Hazard button to
the rear section of the Hazard switch, and separate the 2 pieces and remove switch
from the face of the factory radio.
Hazard Switch Installation Instructions
1. Place the front Hazard switch into the position on the installation kit and insert the
back section of the Hazard switch from the rear and lock the 2 pieces together.
2. Secure the back of the hazard switch to the rear of the kit using the Phillips screws
removed in step 2 of Hazard switch removal instructions.
NDTES
Page 3
Single ISO Mount Applications Cont.
NOTE: #1 • ISO trim ring .. ) may be used in place ol after-market radio's removable trim ring
*2 ■
Spacers must read upright (This side up for single ISO install)
KIT ASSEMBLY INSTRUCTIONS
Double DIN & Double ISO Mount Applications
1 Attach the left and right side brackets to the main frame. See liguie C below
2 For double DIN radio applications ONLY cut and remove center nb froiii and uie ^ ;lgos smooth
3 Follow steps 4-6 from single ISO instructions on page 3 (See note #2 below)
4 Attach a rear support bracket to tire rear of the radio components and ad|ust as needed to atloy/ rear support
bracket to rest ht the sub-dash
NOTE: #1 - ISO trim ring ,
applications, mount after-market radio components to side brackets using screws provided v/ith
radio when possible or hardware included v;ith kit
*2 - Spacers must read upright (Ttiis side up for DBL ISO install)
i
must be used in place ot atter-maikel radio's trim rings For ISO mount
Fig. C
Page 4
NOTES
Single DIN Mount Applications
1. Attach the left and right side brackets to the mam bracket. (See I ig.m
2. Insert pocket (part « into lower section of the mam frame
3. Attach left and right side brackets to the rear of the pocket using screws supplied
4 Insert DIN sleeve from your new radio into the upper section of the installation kit.
5 Depress the tabs from inside the sleeves opening upward, outward, and downward
to secure sleeve to the installation kit.
6. Install radio Into sleeve and lock into place.
7 Attach a rear support bracket to the rear of
the new radio and adjust as necessary to
attach to the rear support stud located o'
the back of the pocket using the small
Phillips screw supplied with kit.
NOTE: ISO tiiin ling (I ..) may be used in
place ol altei-maikei ladio’s lemovable trim ring V
Pi)- ■^)
KIT ASSEMBLY INSTRUCTIONS
single ISO Mount Applications
1 Attach the left and right side brackets to the main bracket (See Figure B pg 4)
2. Insert pocket ‘ into lower section of the main frame
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Attach (1) ISO Spacer to the inside of upper section on both Left & Right mounting
brackets as shown in Fig. A. (See note #2 pg. 4)
5. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or hardwarb included with kit.
6. Slide radio component lorward or backward tor desired look and tighten screws.
7. Attach a rear support bracket to the rear of the new radio a.d adjust as necessary to
aftach to the rear support stud located on the back of the pocket using the small
Phillips screw supplied with kit
Loading...