Page 1
CAW-1130-06
20002-2004 ACURA RSX
RADIO MOUNTING KIT
INSTALLATION INSTRUCTIONS
Page 2
2002-2004 ACURA R5X
DfcSM DISASilMBlY 8, RADIO REMOVAL IMSTKUCTIONt
1
) Cdieluily unsnap ati<J remove thft ijnsh oonel diruuHy helow fho laciory rado.
riiaconteci t^o wire hctrnc&elrcm the panel and remevo panel.
2) H6mo>«e the (2; Phillips screws located directly below Iho rear ol the rado.
3) Carefully pry iaclury r^die leiwS'd Irom the rear ot the radio (CAUTION!!)
Piyii'ig from the face of Ihe factory rad« wihout puilir.g tado 'or^vald Irom
belcw may domago Ihc factory rndm fascia.
't) F.uinove radio from dash cavity.
h) Disconnect Wire harnessus ^nU unloina leac from radio and I la?atd switch,
thuri teiiiuvi. radio.
b) Remove ihe (0) Phillips screws secu iny iiiu laciory radio ta the metal
siip:)ori chassis. Then «move radio Irom chaaais.
7) Henove ’lie (2) sirtews securing i ie Hozuru vmteh to the rear ol the laciory
Coze» and remuvu Hazard switch.
£> Kernove :he {^) Phil ips scre//s securing the irwtal stppoii chassis to the teat
of the factory b(/zel and lemove s.jppor1 cnassis.
KIT PREPARATION INSTRUCTIONS
For All Applications
1) Re-atlach the molai supporl ciiassis to the rear ol the
screv/s removod from :fie factory radio bezel
2) Pe-iristall hazard biillcn lo the roar of tho
letnoveci Irom the factory radio bezel.
using tho screws
using Ihe
NOTES:
1 of 4 Screw»
u»d to oHoch
n>etol <ho$»i>
lo reer c4 Kit
.Fwtory OioMì»
Page 3
Klf ASSEMBLY INSTRUCTIONS
Sin9le ISO Mount Applications
1) Prepare kil as shOAri urdar Preparation Instructions on pago '•
2) Attach loll and rtght side pocket moiirling braokete and secijrc to the rear ol
the pocket using aupplied with kit.
3} Insert pockai into lower section of the rrain bracket ard secure to lire ICAvnr
rrounting holoB ol tire inel:'kl support chassis using thn Phillips screws
remevod f’on the sIdnRnf the fftctory radio.
4) Pomove metsl steeve frorr aftermarket tadin
5) Insert aftermurkol iodic mio upper ccaUcn c4 lot a-id secure radio tn metal chnsss
redre mountmg troie loeations.
Kl¥ ASSiMBLY INSTRUCTIONS
Double DIN & Double ISO Mount Applicotions
1) Prepare kil as sf'own uitder Preparalioa Insfiictions on page 1.
2) Cut and remove contr>' n:r from main bracket kr coublc 0 N and coublo
ISO appiicahons
:0 For double DII4 iMdio applicalivns ONLV cut and inrrova cer>!er rit from
and 1 lo edges smoolh.
4) Runiuve ineta slee'/o Iro n aitermarkot radics (OcuUe ISO app icattons only}.
5) Insert afierniaiket radiofs} imo meial ut assis sipport fraino and secure ttiirg
Phillips scrrtws rornovodtrom the sides o' ti e tac'ory radio.
3) For Double DIN sizod rados ct.l and romeve carrier rib irom the
and fie :he edges smooth.
I"
V.:-... Ii;r\
; r
radio»
Page 4
NOTES:
KIT ASSiMBLY INSTRUCTIONS
Single DIN Mount Applications
1) Prepare kit as sho\vn Liider Preparaiioo Instructions on pege 1.
P) Attach leli and right side pocket mounlng hiackcts and securo (o tie rear o1
the pcokat using screws supplied with kit.
3) Insert pccket into lo/mr seclon of the main bracket and secure to itw lowc'
irtoun:ing holes ol the mmal scppotl chassis using the Phillips screws
removed from ttie eidrrs rt the factory rad o.
4) Insert Ot^ sleovo (sjppUod witti r&d>o) from your new radio ittto the upper
secticr> of the notaitation <it.
5) Depress tliu tubs from inside Pie sleeves epenirg upward, oiihvsrd. ar d
dowrmaiU to ¡¡ecure sleeve >o The insfallafon kil.
6) Install radio into sleeve and took into pkcu.
7) Attach a rear support bracket (supplied with most aftermarket ruoios) to tie
rear cl The new radio and acjusf as necessary to attach to ihe reui support
Sturt bcaiod on me back cl the p.-x:kel using (i) small philips screw supplied
with kil.
Loading...