Ken Tool 30171 User Manual

768 E. North Street ● P. O. Box 9320 ● Akron, Ohio 44305

Toll Free: 888-536-8665 ● Fax: [phone]

Phone: [phone] ● Fax: [phone]

E-mail: [e-mail] ● www.kentool.com

13 PC. HUBCAP & WHEEL

PART NO. 30171

LOCK REMOVAL KIT

 Quickly remove wire wheel cover locks with variable inside drive keys on GM, Ford and Chrysler

products.

 Easily removes aftermarket wheel locks without damaging the lock or stud.
 Quickly remove large GM cover locks with variable inside drive keys.
 Easily remove Corvette, GM “M” and “F” body wheel locks (GrandAm, Firebird,

Bonneville, Olds Calais, Buick Regal).

 Removes and replace GM, Ford, Chrysler and McGard hubcap locks and aftermarket wheel lug

locks...without keys...without waiting!

 GUARANTEED: For one full year against defects in materials and workmanship.

INSTRUCTIONS FOR USE:

Sockets ARE NOT TO BE HAMMERED/POUNDED onto wheel lock. Simply apply pressure against wheel
lock while either running impact gun in reverse, or turning ratchet/wrench counterclockwise with removal
socket attached.

NOTE:

 When using socket with smooth tapered inside profile, run impact gun clockwise for 10 seconds heat-

ing up wheel lock and socket. This will create a temporary shrink-fit bond.

 Pause for 10 seconds.
 Change direction of impact gun to counterclockwise/reverse and, while applying pressure against the

wheel lock, run the impact gun to remove wheel lock. Sometimes a breaker bar and hand turning will
give better results.

MADE IN USA



 Kit Includes: ● GM Hubcap Lock Remover ● GM Sprocket Hubcap Lock Remover ● Ford and

Chrysler Hubcap Lock Remover ● Large Universal Locking Lug Nut Remover ● Large Wheel Cover
Lock Remover ● Oversized Wheel Lock Remover ● Corvette, GM “M” and “F” Body Wheel Lock
Remover ● Stripped 18MM Lug Nuts, Corvette & GM Lock Remover ● 19MM, 3/4” Damaged Wheel
Lug & Overized Wheel Lock Remover ● 7/8” Damaged Wheel Lug & Oversized Wheel Lock Remover

● Lug Nut Remover Punch ● 3” Extension ● Durable Plastic Carrying Case ● Directions for Use.

30171 PARTS BREAKDOWN

LARGE GM TRIANGULAR WELL
HUBCAP LOCKS: Insert hex end of

tool into well. Turn with 3/4” wrench to
remove lock.

30170-20

GM SPLINE HUBCAP LOCKS: Find the best-fit position and

slip or tap tool onto splined hubcap lock. Turn tool with a 3/4”
wrench to remove lock. Do not use an impact wrench with

30170-40

GM HUBCAP LOCKS: Drive socket onto lock. Turn tool with a

1/2” socket to remove lock.

30170-60

FORD & CHRYSLER HUBCAP
LOCKS: Drive tool onto lock. Turn

tool with a 3/4” socket to remove lock.

30170-10

30170-30

GM HUBCAP LOCKS: Drive tool onto lock. Turn tool with a 3/4”

socket to remove lock.

30170-50

FORD & GM WHEEL LOCKS: Drive socket onto lock. Turn tool

with a 1/2” drive to remove lock.

30170-70

GM WHEEL LOCKS & OVERSIZE AFTERMARKET WHEEL
LOCKS: Drive socket onto lock. Turn tool with a 1/2” drive to

remove lock.

30170-80

EXTRACTOR PUNCH: Insert punch in 1/2” square drive hole.

Tap to remove lock from socket.

30171-10

STRIPPED 18MM NUTS, CORVETTE & GM WHEEL
LOCKS: Drive socket onto lock. Turn tool with a 1/2” drive to

remove lock.

30115-05

7/8” DAMAGED WHEEL LUG & OVER­SIZED WHEEL LOCK REMOVER:

Place socket onto lock. Insert 3” exten­sion. Turn tool with a 1/2” drive to re­move lock.

OVERSIZE AFTERMARKET WHEEL LOCKS: Drive socket
onto lock. Turn tool with a 1/2” drive to remove lock.

30170-90

LARGE DIAMETER CHRYSLER LOCKS: Drive socket onto

lock. Turn tool with a wrench to remove lock.

30115-02

19MM, 3/4” DAMAGED WHEEL LUG & OVERSIZED
WHEEL LOCK REMOVER: Place socket onto lock. Insert 3”

extension. Turn tool with a 1/2” drive to remove lock.

30110-06 3” EXTENSION

WARNING

WEAR ADEQUATE EYE PROTECTION WHEN USING THIS TOOL!

CLEAN THE GRIPPING SURFACES OF SOCKETS AND LOCKS.

30171-1 INSERT.PDF