Page 1
INSTRUCTIONS FOR MIDI INTERFACE
LINNDRUM Mk 2/3
Your Linndrum is now equipped to send and receive MIDI information.
When turned on the machine will function normally, sending out and
receiving MIDI note & velocity information on the channels set in
memory. The factory channel settings are: receive chan 16 omni off
transmit chan 1 and Stop/start TX/RX enabled
Clock information is always sent and Start/stop information is sent
and received if enabled. (Not channel sensitive)
YOU CAN RETURN TO THE FACTORY MIDI SETTINGS BY SWITCHING THE MACHINE
ON WHILST HOLDING THE RED BUTTON PRESSED (hold for a couple of seconds)
With the front panel push switch set to INTERNAL clock (red led not lit)
the Linndrum will run from its own internal clock and will send out
MIDI timing information at a rate determined by the tempo knob. In the
EXT sync position (red led lit) however, with the rear panel switch set
to MIDI (up) it will run from MIDI sync at the rate set by the MIDI
device connected. If no MIDI timing information is present,then the
Linndrum will not run.
Some drum machines/sequencers may not send start/stop codes, in this
case pressing the start switch on the Linn, will make it wait until
MIDI clock/sync is present.
To use the EXTERNAL sync socket (tape sync) the front panel switch
should still be set to EXT (red led lit), but the rear panel switch
should be set to EXTERNAL (down).
RED PUSH BUTTON Two modes are available by pushing the red push button. Before you do
press the red button however, make sure the Linndrum is not playing,
otherwise the results may be unpredictable.
1) SET-UP MODE - setting MIDI channel/stop-start etc. (panel or remote)
Give the red push button a short press (half a second) - then release.
Follow this with a MIDI note (a key on a DX7 D50 etc.) or sequence of
notes as detailed on page 3. Note that after selecting a channel
or other function, top C will need to be pressed to return the unit to
playing mode. (N.B. set-ups are stored in non volatile memory).
2) MAPPING MODE - assigning MIDI notes to sounds (from remote synth
only) - Press the red button hold for about six seconds - then release.
Follow this (on the remote keyboard) with a program change number, then
any MIDI note. The drum sound specified by that program change number
will be mapped to the key you pressed. You may keep assigning drum
sounds to keys in the same fashion (program then key). When you have
assigned all the sounds that you want to, press any invalid program
change number (any above 16), you will then be automatically returned
to normal play mode. On page 4 is a list of which program numbers
correspond to what drum sounds.
N.B. The red button can be "pressed via MIDI - see last page.
Page 2
You can also set channels etc on the Linn itself as described below
The top row of eight buttons (Hihat 1 thru Ride 2) are Rx Tx channel
numbers 1 to 8 and they become 9 to 16 if the percussion led is lit.
On the bottom row, Bass 1 selects Receive chan, Bass 2 selects Transmit
chan, Sidestick selects [omni-on mode], Snare 1 selects [omni-off mode],
Snare 2 selects [disable start/stop codes RX & TX through MIDI], Snare 3
selects [enable start/stop codes TX & RX through MIDI], and Crash is the
ENTER key to return you to the normal operating state.
So the sequence of events is :- Red push button - (then optionally
omni on or off) - then recieve or transmit select [bass 1 or 2] then a channel number [1 thru 16] - then press crash to ENTER
As an example - to get transmit channel 5 and receive channel 10, but
leave it in omni-off mode.
1) Press the red button
2) Press Bass 2 (transmit select)
3) Press Mid tom (perc led not lit) [transmit ch 5 now set]
4) Press Bass 1 (receive select)
5) Press Percussion button (to get to channels 9 to 16)
6) Press Cabasa 2 (perc led lit) [receive ch 10 now set]
7) Press Crash - to ENTER (return to normal operating mode)
Note that when the red button has been pressed, the panel buttons
will not make sounds when pressed, until normal playing mode is
resumed by pressing ENTER (Crash).
OPERATION OF DRUM BUTTONS IN SET-UP MODE
------ ------ ------ ------ ------ ------ ------ ----- | Chan | Chan | Chan | Chan | Chan | Chan | Chan | Chan |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
| 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 |
------ ------ ------ ------ ------ ------ ------ ------
------ ------ ------ ------ ------ ------ ------ ----- | Omni | Omni | Dis- | En- | RX | TX | | Sel |
| | | able | able | | |ENTER | 1-8 |
| on | off | START & STOP| mode | mode | | 9-16 |
------ ------ ------ ------ ------ ------ ------ ------
Red percussion light off = chan 1-8
Red percussion light on = chan 9-16
Assign mode cannot be used from the front panel buttons
Page 3
C Receive channel 1 Bottom C - MIDI note no. 36
Db " " 2
D " " 3
Eb " " 4
E " " 5
F " " 6
Gb " " 7
G " " 8 Selecting a receive channel
Ab " " 9 will automatically put the
A " " 10 MIDI into omni off mode.
Bb " " 11 That is, it will receive on
B " " 12 the selected channel only.
C " " 13
Db " " 14
D " " 15
Eb " " 16 (default)
E not used
F Omni on mode
Gb not used
G not used
Ab not used
A not used
Bb not used
B not used
C Transmit channel 1 (default) [ Middle C ] MIDI note number 60
Db " " 2
D " " 3
Eb " " 4
E " " 5
F " " 6
Gb " " 7
G " " 8 The transmit channel can be
Ab " " 9 changed independently of the
A " " 10 of the receive channel, and
Bb " " 11 can be set even during omni
B " " 12 on mode.
C " " 13
Db " " 14
D " " 15
Eb " " 16
E not used
F not used
Gb not used
G not used
Ab not used
A not used
Bb not used
B not used
C not used
Db not used
D not used
Eb not used
E Disable start and stop through MIDI
F Enable start and stop through MIDI (default)
Gb not used
G not used
Ab not used
A not used
Bb not used
B not used
C ENTER KEY - Press and release. Top C - MIDI note no. 96
Page 4
Program number use in Assign mode
Program 1 - Bass 1/2
2 - Snare 1/2/3
3 - Sidestick
4 - Hihat 1/2
5 - Hihat open
6 - Lo conga
7 - Hi conga
8 - Lo tom
9 - Mid tom
10 - Hi tom
11 - Ride 1/2
12 - Crash
13 - Cabasa 1/2
14 - Tambourine 1/2
15 - Cowbell
16 - Clap
1) No matter how the sounds are assigned, these program numbers always
belong to the same sound.
2) Any program number above 16 will terminate Assign mode and return you
to normal play mode.
3) If you assign more than one sound to the same MIDI note, only the
most recent one will sound - the original sound on that note will then
be "unassigned" until it has been given a new assignment.
When sounds are unassigned, they will not be transmitted over MIDI
4) Assignments are stored in non volatile memory.
5) The various volume levels are accessed via MIDI at different
velocity levels - and as a bonus, Sidestick has 3 volume levels (like
snare) and Hihat open and Crash have 2 levels - (MIDI in only)
6) If "MIDI CONTINUE" is received during song mode, the LINNDRUM will
start at the beginning of the current pattern.
Page 5
MIDI CONTROL OF RED PUSH BUTTON
The red push button can be "pressed" via MIDI as MIDI switch number
95 (5Fh) for regular program mode or 94 (5Eh) for transpose mode.
The selection of the push button is enough, it doesn’t matter if it
is being turned on or off.
In hexadecimal BX - 5F - 00 = set-up mode
In hexadecimal BX - 5E - 00 = mapping mode
Where X is the current MIDI channel.
[n.b. whilst in set-up/mapping modes the MIDI is in omni on mode]
MIDI connectors -
MIDI IN should be connected to a MIDI OUT or a MIDI THRU
similarly MIDI OUT should be connected only to a MIDI IN
and a MIDI THRU should also be connected only to a MIDI IN.
MIDI OUT is the signal from the synthesiser (or drum machine etc.)
that is to be sent to another instrument. MIDI IN is a received
signal that contains MIDI information from another synth, and MIDI
THRU is an exact copy of information arriving at the MIDI IN socket.
This allows several instruments to be connected together.
If you want to wire your own MIDI cables the following information
may be useful.
1) Although a 5 pin connector is used, only two connections plus an
earth connection are required.
2) If you look at the din plug from the wiring side you will see
that the pins are numbered. From left to right (or clockwise) these
are 1 - 4 - 2 - 5 - 3.
3) The pins numbered 1 & 3 are not used.
4) The screen (earth) is connected to pin 2 (centre pin)
5) Pin 4 of one plug should be connected to pin 4 of the other
6) Pin 5 of one plug should be connected to pin 5 of the other
7) You should now have a working MIDI lead
8) It is preferable to label one end of the cable MIDI IN & the
other end MIDI OUT, to avoid confusion.
Copyright (c) KENTON Electronics & John Price 1986-2001
Kenton Electronics
Brookfarm House
Station Road
South Wimbledon
London
SW19 2LP
UK
Tel +44 (0)20 8544 9200
Fax +44 (0)20 8544 9300
www.kenton.co.uk
LIN24006 940404/2320/JKP
Loading...