KENTMASTER BANDMASTER BM-V-LD, BANDMASTER BM-V-LB Operation, Instruction, Installation, Maintenance And Partsbook

REV F: 30/12/05

BM-V-LD, BM-V-LB

INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK

IMPORTANT: READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR

SERVICING THIS TOOL.

TOOL DATA

MODEL: BANDMASTER BM-V-LD
ASSEMBLY NO. 1708070
TYPE: ELECTRICAL OPERATED
NET WEIGHT: 166 LB (75.5 KG)
MOTOR HORSEPOWER: 2HP / 3HP

LOIN DROPPERS

MODEL: BANDMASTER BM-V-LB
ASSEMBLY NO. 1740000
TYPE: ELECTRICAL OPERATED
NET WEIGHT: 200 LB (91 KG)
MOTOR HORSEPOWER: 3HP / 5HP

VIBRATION: LESS THAN (<) 123 dB < 1.41m/s2
NOISE: LESS THAN 81dB

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

1 OF 43

= Hazards or unsafe practices which could result in severe personal injury,

! WARNING

death or substantial property damage.

= Hazards or unsafe practices which could result in minor personal injury,

! CAUTION

product or property damage.

= Important installation, operation or maintenance information.

! NOTICE

OPERATING AND SAFETY INSTRUCTIONS

! WARNING

! WARNING

! WARNING

! WARNING
! WARNING

! WARNING

! WARNING

! WARNING

! WARNING

! WARNING

! WARNING

! WARNING

! WARNING

! CAUTION

! WARNING

DO NOT OPERATE THIS TOOL UNTIL YOU HAVE READ AND UNDERSTOOD THE SAFETY
INSTRUCTIONS AND OPERATING MANUALS.

DO NOT OPERATE THIS TOOL UNTIL YOU HAVE RECEIVED TRAINING IN THE HANDLING,
OPERATION AND USE OF THIS TOOL.

STOP USING A MALFUNCTIONING OR DEFECTIVE TOOL IMMEDIATELY. REPORT ANY
PROBLEMS OR DEFECTS TO YOUR SUPERVISOR FOR REMOVAL OF THE TOOL FROM
SERVICE.

DO NOT ATTEMPT TO REPAIR THE TOOL YOURSELF.
DO NOT ALLOW UNAUTHORIZED PERSONS TO USE TOOL.
REMOVE AND DISCONNECT POWER FROM THE TOOL WHEN TOOL IS LEFT UNATTENDED OR

IS NOT IN USE.
NEVER TIE DOWN, BYPASS, ALTER OR MODIFY THE ACTIVATING SWITCHES OR TRIGGERS OF

THIS TOOL.
NEVER MAKE ALTERATIONS OR MODIFICATIONS TO THIS TOOL.
BE CONSTANTLY AWARE AND ALERT FOR UNSAFE CONDITIONS AND REPORT THEM

IMMEDIATELY TO YOUR SUPERVISOR.
NEVER PLACE YOUR HAND OR ANY PART OF YOUR BODY IN THE CUTTING PATH OF THE

TOOL.
NEVER ALLOW ANYONE ELSE TO PLACE THEIR HANDS OR ANY PART OF THEIR BODY IN THE

CUTTING PATH OF THE TOOL.
DO NOT ACTIVATE CONTROL SWITCHES OR TRIGGERS OF THIS TOOL UNLESS YOU INTEND

TO TEST OR OPERATE THIS TOOL.
DO NOT USE THIS TOOL FOR ANY PURPOSE OTHER THAN IT’S INTENDED PURPOSE.
WHEN OPERATING THIS TOOL WEAR THE PROTECTIVE GEAR AND SAFETY EQUIPMENT

SUPPLIED TO YOU.
THE NOISE EMISSION (SOUND PRESSURE LEVEL) AT THE WORKSTATION MAY EXCEED 80 dB

(A). EAR AND SOUND PROTECTION GEAR IS REQUIRED.
VIBRATION: LESS THAN (<) 123 dB < 1.41m/s
NOISE: LESS THAN 81dB

2

REV F: 30/12/05

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

2 OF 43

REV F: 30/12/05

OPERATING INSTRUCTIONS

! WARNING

1. TO ENSURE TOOL IS OPERATING PROPERLY, PERFORM FOLLOWING STEPS AT START OF EACH SHIFT:

• MAKE SURE TOOL MOVES UP AND DOWN FREELY WHILE HANGING FROM BALANCER OVERHEAD.

• WITH POWER TO TOOL TURNED ON, TEST TRIGGER FOR PROPER OPERAT ION.

• DEPRESS EACH TRIGGER SEPARATELY. TOOL SHOULD NOT ACTIVATE. DEPRESS BOTH TRIGGERS.

TOOL SHOULD ACTIVATE.

• IF TOOL HAS "ANTI-TIE DOWN" OPTION, BOTH TRIGGERS MUST BE DEPRESSED SIMULTANEOUSLY FOR
TOOL TO ACTIVATE.

2. TO PERFORM WORK, HOLD TOOL FIRMLY AT BOTH HANDLES. SQUEEZE TRIGGERS TO ACTIVATE TOOL.

3. START CUT WITH SAW NOSE POINTED UP AT AN ANGLE.

4. LEVEL SAW TO HORIZONTAL POSITION IN LOIN AREA.

5. POINT NOSE OF SAW AT DOWNWARD ANGLE IN CHUCK AND NECK AREA.

6. A BEGINNING SPLITTER CAN MARK BACKFAT OF BEEF WITH A KNIFE TO HELP SAW DOWN CENTER OF BACKBONE AND

UNTIL OPERATOR IS FAMILIAR WITH SPLITTING PROCEDURE.

7. DO NOT EXERT EXCESSIVE PRESSURE. ALLOW TIME FOR THE TOOL TO CUT.

8. PUSH SAW FORWARD SO THAT GUARDS, ITEMS 1 AND 2 FIGURE 1, RIDE AGAINST BEEF. THIS HELPS STEADY

SAW IN CUT AND HELPS ELIMINATE BLADE JUMPING AND CHATTERING.

ONLY TRAINED PERSONNEL ARE TO OPERATE THIS TOOL.

MAINTENANCE

ONLY TRAINED AND QUALIFIED PERSONNEL ARE TO PERFORM MAINTENANCE

! WARNING

AND SERVICE TO THIS TOOL.

1. TOOL REQUIRES GREASING AFTER 40 HOURS OF OPERATION. GREASE USING KENTMASTER GREASE (PART NO.

7903070).

BLADE REMOVAL AND CLEANING.

ALWAYS DISCONNECT POWER SUPPLY FROM TOOL BEFORE INSTALLING OR

! WARNING

REMOVING BLADE FROM TOOL.

ALWAYS WEAR WIRE MESH GLOVES WHEN INSTALLING OR REMOVING BLADE FROM TOOL.

! WARNING

1. REMOVE PAPER WRAPPER FROM BLADE.

2. OPEN COVERS, FIGURE 1, ITEMS 1,2, 3 AND 4.

3. INSTALL TORQUE WRENCH, ITEM 5, INTO SCREW, FIGURE 1, ITEM 6, AND TURN COUNTER-CLOCKWISE (CCW).

THIS ALLOWS TAKE-UP WHEEL AND SLIDE, ITEMS 7 AND 8, TO RETRACT.

4. SLIDE TAKE-UP WHEEL TO RIGHT.

5. HOLD BLADE, WITH TEETH FACING AWAY FROM YOU, AND INSTALL INTO SLOT OF BEAM, CONTINUING

AROUND AND OVER THE TAKE-UP AND DRIVE WHEELS.

6. TURN TORQUE WRENCH CLOCKWISE (CW) TO ELIMINATE BLADE SLACK AND TIGHTEN TAKE-UP WHEEL
AGAINST BLADE (TORQUE WRENCH IS PRESET AT FACTORY AND WILL SLIP AFTER PLACING PROPER
TENSION ON BLADE).

7. TWIST BLADE 90° AT BLADE GUARDS AND INSERT BLADE INTO SLOTS WITH TEETH FACING DOWNWARD.

8. TURN DRIVE WHEEL, ITEM 9, SLOWLY BY HAND, TO CHECK TRACKING OF BLADE ON WHEELS.

9. RETORQUE AGAIN UNTIL TORQUE WRENCH SLIPS.
AT END OF EACH SHIFT:

1. REMOVE SAW BLADE.

2. IF USING BLADE AGAIN, WASH BLADE WITH HOT WATER TO REMOVE FAT, MEAT AND BONE PARTICLES.

3. DRY AND APPLY A COAT OF MINERAL OIL TO ENTIRE SURFACE OF BLADE TO AVOID OXIDATION.

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

3 OF 43

REV F: 30/12/05

CLEANING AND STERILIZING SAW

AT END OF EACH SHIFT:

1. REMOVE SAW BLADE.

2. CLEAN AND WASH DOWN BOTH INSIDE AND OUTSIDE OF ENTIRE MACHINE THOROUGHLY WITH HOT WATER

AND CLEANING AGENT. AVOID USING HARSH CAUSTIC CLEANERS ON MACHINE.

3. WASH OFF ALL BONE DUST AND MEAT PARTICLES FROM INSIDE OF FRAMES, AROUND WHEELS AND GUIDES.

4. SPRAY BOTH INSIDE AND OUTSIDE OF MACHINE WITH A LIGHT COAT OF MINERAL OIL.

WATER CONNECTION

A BULKHEAD FITTING, FIGURE 1, ITEM 10, IS PROVIDED AT THE BASE OF DRIVE SIDE FRAME, ITEM 11, FOR
CONNECTION TO COLD WATER. ADJUST CONNECTOR AND NOZZLE, ITEMS 12 AND 13, TO CLEAN BONE DUST
FROM DRIVE WHEEL AND MEAT PARTICLES TRAPPED BETWEEN TEETH OF SAW BLADE. FITTING AND HOSE,
ITEMS 14 AND 15, AT BASE OF DRIVE SIDE FRAME, ARE PROVIDED FOR DRAINAGE OF WASTE WATER.

TORQUE WRENCH CALIBRATION

TORQUE WRENCH, ITEM 5, IS CALIBRATED AND PRESET TO 55 INCH/LBS AT FACTORY. PERIODICALLY CHECK
CALIBRATION BY USE OF ANOTHER TORQUE WRENCH WITH A DIAL TO MAKE ADJUSTMENT AND RESET TORQUE
WRENCH TO 55 INCH/LBS. REMOVE TORQUE WRENCH COVER TO CLEAN AND LUBRICATE PERIODICALLY.

TESTING AND SETTING OF TORQUE WRENCH:
TOOLS REQUIRED:

HEX WRENCH -- 3/16"
HEX BAR -- 1/2", ABOUT 3"-6" LONG
HEX SOCKET -- 1/2" WITH DRIVE END TO MATCH COMMERCIAL WRENCH SELECTED
TORQUE WRENCH, COMMERCIAL DIAL TYPE PREFERABLE
SCREWDRIVER -- 3/8"-7/16" FLAT BLADE

STEP 1 -- TESTING KENTMASTER TORQUE WRENCH
A. ATTACH COMMERCIAL TORQUE WRENCH TO KENTMASTER TORQUE WRENCH USING 1/2" HEX BAR AND

1/2" HEX SOCKET.
B. HOLD ASSEMBLY FIRMLY AND ROTATE KENTMASTER TORQUE WRENCH CLOCKWISE SLOWLY UNTIL
WRENCH "SLIPS".
C. INDICATOR NEEDLE ON COMMERCIAL TORQUE WRENCH SHOULD READ 55 IN/LBS ±3 IN/LBS (5%).
IF OVER OR UNDER VALUE, PROCEED TO STEP 2 -- RESETTING KENTMASTER TO RQUE WRENCH.

STEP 2 -- RESETTING KENTMASTER TORQUE WRENCH
A. USING 3/16" HEX WRENCH, REMOVE FOUR (4) SCREWS HOLDING THE WRENCH HANDLE IN PLACE.

REMOVE HANDLE AND GASKET. SET ALL PARTS ASIDE FOR REUSE.
B. HOLD WRENCH BODY SECURE BY EITHER CLAMPING SMALL DRIVE END IN VISE OR BY CLAMPING THE
1/2" HEX BAR IN VISE AND ATTACHING WRENCH TO BAR.

C. USE FLAT BLADE SCREWDRIVER TO ADJUST THE FOUR (4) SET SCREWS UNDER WRENCH HANDLE.
USE A STAGGERED PATTERN WHILE ADJUSTING, SUCH AS UPPER, LOWER, LEFT THEN RIGHT.

• TO REDUCE TORQUE VALUE - BACK OFF SET SCREWS COUNTER-CLOCKWISE ABOUT 1/8 TURN EACH.

• TO INCREASE TORQUE VALUE - TURN IN SET SCREWS CLOCKWISE ABOUT 1/8 TURN EACH.
D. REASSEMBLE TORQUE WRENCH WITH HANDLE AND GASKET. RETEST PER STEP 1. CONTINUE TESTING
AND SETTING UNTIL WRENCH OPERATES AT PROPER TORQUE VALUE.

NOTE: Do not clamp body of Torque Wrench in vise as

severe damage to Torque Wrench could occur.

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

4 OF 43

REV F: 30/12/05

HANGER

THE SAW HANGER INCORPORATES TWO (2) ADJUSTMENT FEATURES: ADJUSTMENT "V" (VERTICAL) AND ADJUSTMENT
"H" (HORIZONTAL). TO ADJUST THE SAW, LOOSEN TWO (2) SCREWS, ITEM 16, FIGURE 1 AND ADJUST ACCORDINIGLY.
TURN SHAFT ITEM 17, FIGURE 1 TO ADJUST WEIGHT OF SAW FROM FRONT TO REAR ACCORDING T O OPERATOR
PREFERENCE.

TOOTH
DIRECTION

Figure 1 BM-V-LD

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

5 OF 43

REV F: 30/12/05

TROUBLE SHOOTING HINTS:

• BE SURE DRIVE WHEEL IS TURNING COUNTER-CLOCKWISE (CCW) AND
BLADE IS INSTALLED WITH TEETH POINTED TOWARD DRIVE FRAME.

• BE SURE BLADE TEETH ARE SITTING ABOVE UNDERCUT ON BOTH WHEELS
SO AS NOT TO AFFECT SET OF TEETH.

• CHECK GAP BETWEEN CARBIDE INSERTS WHICH MUST NOT BE TOO TIGHT

BAD SPLIT

MAKE ADJUSTMENT IF NECESSARY.
UNEVEN SPLIT

• REPLACE SAW BLADE IN CASE BLADE IS DEFECTIVE.

CUTS TO LEFT OR RIGHT

• ADJUST SAW HANGER (ADJUSTMENT "V") IF SAW CUTS OFF CENTER TO
RIGHT OR LEFT.

• ADJUST HANGER ("H" ADJUSTMENT) IF SAW NOSE RISES TOO EASILY AND
ADDITIONAL WEIGHT MUST BE SHIFTED FORWARD.

• BE SURE SAW IS NOT DROPPING DOWN TOO QUICKLY. ADJUST BALANCER.

• BLADE OVER OR UNDER TORQUED. CHECK TORQUE WRENCH CALIBRATION.
________________________________________________________________________________________________________

• CHECK IF BLADE IS BREAKING AT WELD. BLADE MAY BE DEFECTIVE.

• WHEELS SLIPPING IN BLADE (EVIDENT BY VERY SHINY BLADE SURFACE).
CHECK FOR INCORRECT TORQUE SETTING. CHECK TORQUE WRENCH

PREMATURE BLADE
CRACKING OR BREAKING

• OPERATOR PUSHING SAW THROUGH BEEF EXCESSIVELY.

• BLADE OVER OR UNDER TORQUED. CHECK TORQUE WRENCH CALIBRATION.

• CHECK FOR PROPER GAP (.025"-.028", .64-.71mm) BETWEEN CARBIDE INSERTS.

________________________________________________________________________________________________________

• CHECK FOR BONE DUST BUILD-UP AT GUIDES. CLEAN OUT AND INCREASE

WATER FLOW IF NECESSARY.

• CHECK IF BLADE IS SLIPPING ON WHEELS. LOOK FOR CAUSE AND CORRECT.

BLACK APPEARS
ON BACKBONE

GAP MAY BE TOO TIGHT, CAUSING INSERTS TO MACHINE SIDES OF BLADE.

• CHECK FOR CHIPPED OR CRACKED CARBIDE INSERTS AT BLADE GUARD
ASSEMBLIES. ROTATE OR REPLACE IF NECESSARY.

• WITH BLADE REMOVED, CHECK TAKE-UP WHEEL TO BE SURE IT SPINS FREELY.

________________________________________________________________________________________________________

• CHECK WHEELS FOR PLAY, LOOSENESS OR LOOSE SCREWS OR NUTS.

CHECK TAKE-UP WHEEL BRACKET, TIGHTEN AND CORRECT PLAY.

• CHECK WHEEL BEARINGS AND REPLACE IF DEFECTIVE.

BLADE SLIPS OFF WHEELS

NOT TAPERED OR HAVE FLAT SPOTS DUE TO WEAR. REPLACE IF DEFECTIVE.

• CHECK TAKE-UP WHEEL FOR PROPER TORQUE SETTING.

• LOOK FOR ANY BLADE OBSTRUCTIONS.

OR TOO LOOSE. BLADE SHOULD SLIDE THROUGH WITHOUT PLAY.

CALIBRATION.

• CHECK FOR PROPER GAP (.025"-.028", .64-.71mm) BETWEEN CARBIDE INSERTS.

• CHECK WHEELS FOR ROUNDNESS AND WEAR. BE SURE WHEEL FACES ARE

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

6 OF 43

REV F: 30/12/05

• CHANGE SAW BLADE. BLADE MAY BE DEFECTIVE.

• REMOVE BLADE FROM MACHINE. BACK OFF SCREW, ITEM 6, WITH TORQUE
WRENCH. GRAB TAKE-UP WHEEL WITH BOTH HANDS AND SLIDE BACK AND

MOTOR PULLS EXCESSIVE
AMPERAGE (W ITHOUT LOAD)

OF SLIDE ARE TOO CLOSE AND TIGHT AGAINST SLIDE. LOOSEN SCREWS THAT

OR
BLADE IS TOO LOOSE WHILE
TORQUE WRENCH IS
PROPERLY CALIBRATED

SLIDE AND GIB.
________________________________________________________________________________________________________

FORTH. IT SHOULD SLIDE FREELY. IF IT BINDS OR TAKES EXCESSIVE EFFORT,

DISASSEMBLE COMPLETELY. CHECK TO SEE IF GIBS LOCATED ON EACH SIDE
HOLD GIB IN PLACE. SPREAD GIBS SLIGHTLY OUT AND RETIGHTEN SCREWS.

SLIDE SHOULD MOVE BACK AND FORTH FREELY, BUT WITHOUT UP AND DOWN

PLAY. REASSEMBLE AND TEST MACHINE. LUBRICATE SURFACES BETWEEN

SERVICE

1. KEEP GOOD RECORDS OF ALL SERVICE ACTIVITY AND INCLUDE TOOL IN PREVENTIVE MAINTENANCE PROGRAM.

2. USE ONLY GENUINE KENTMASTER REPLACEMENT PARTS TO ASSURE PROPER PERFORMANCE OF TOOL.

3. CONTACT THE KENTMASTER SUPPLIER NEAREST YOU FOR PARTS

AND CUSTOMER SERVICE INFORMATION.

PARTS BOOK

MODELS MAIN ASSEMBLIES

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

7 OF 43

REV F: 30/12/05

8 OF 43

Figure 2 MODELS BM-V-LD

 TELEPHONE: [phone] FAX: [phone]

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

REV F: 30/12/05

ITEM PART # DESCRIPTION QTY

OPTIONS 2HP MOTOR ASSEMBLY 1

1

OPTIONS 3HP MOTOR ASSEMBLY 1

1720000 POWER SUPPLY, 42V, ANTI-TIE DOWN 1
1720010 POWER SUPPLY, 42V, NO ANTI-TIE DOWN 1
1720020 POWER SUPPLY, NON 42V, ANTI-TIE DOWN 1

2

1720030 POWER SUPPLY, NON 42V, NO ANTI-TIE DOWN 1
1720005 POWER SUPPLY, SINGLE PHASE, 115V 1

1720030 POWER SUPPLY, SINGLE PHASE, 230V 1
3 4501610
4 1700800
5 1709790
6 1704130 CAP 1
7 1704220 GASKET 1

1705590 GEAR, DRIVE / USE WITH 2HP MOTOR 50/60 Hz 1
8

1704150 GEAR, DRIVE / USE WITH 3HP MOTOR 60Hz 1

1704430 GEAR, DRIVE / USE WITH 3HP MOTOR 50Hz 1

1705850 GEAR, DRIVEN / USE WITH 2HP MOTOR 50/60 Hz 1
9

1707340 GEAR, DRIVEN / USE / WITH 3HP MOTOR 60Hz 1

1707350 GEAR, DRIVEN / USE WITH 3HP MOTOR 50Hz 1

10 1708071 DRIVE SIDE ASSEMBLY 1
11 1708430 COVER 1
12 1708460 COVER, GEAR 1
13 1708500 DRIVE WHEEL ASSEMBLY 1
14 1708610 COVER 1
15 1708840 FITTING 1
16 1709201 TAKE-UP SIDE ASSEMBLY 1
17 1709620 FLANGE 1
18 1709630 SHAFT 1
19 1709840 BEAM 1
20 1710070 NUT 1
21 1710090 HANDLE ASSEMBLY 2
22 3000090 LOCKWASHER 1
23 3001090 LOCKNUT 1
24 3200080 BEARING 1
25 3316050 BEARING 1
26 4111020 BLADE 1
27 7000020 PLUG 2
28 7000420 ELBOW 1
29 7007730 MALE BRANCH TEE 1
30 7036150 FITTING 1
31 7240710 WINDOW 1
32 7300200 DISCHARGE HOSE 1
33 7300755 TUBE 1
34 7310170 HOSE 1
35 7681530 O-RING 1
36 7681650 O-RING 1
37 7798170 SEAL 1
38 7798220 SEAL 1
39 8211100 SCREW 4
40 8607060 KEY 1
41 9211050 SCREW 10
42 9215080 SCREW 6
43 9215100 SCREW 5
44 9239050 SCREW 10
45 9243080 SCREW 1
46 9413070 SCREW 3

1708070: BENDMASTER BM-V-LD

WRENCH / TOOL
TORQUE WRENCH / TOOL
WRENCH, ADJUSTMENT / TOOL

1
1
1

Figure 3 BOM FOR MODELS BM-V-LD

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

9 OF 43

REV F: 30/12/05

10 OF 43

Figure 4 MODEL BM-V-LB

 TELEPHONE: [phone] FAX: [phone]

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

REV F: 30/12/05

1740000: BENDMASTER BM-V-LB

ITEM PART # DESCRIPTION QTY

OPTIONS 3HP MOTOR ASSEMBLY 1

1

OPTIONS 5HP MOTOR ASSEMBLY 1

1720000 POWER SUPPLY, 42V, ANTI-TIE DOWN 1
1720010 POWER SUPPLY, 42V, NO ANTI-TIE DOWN 1

2

1720020 POWER SUPPLY, NON 42V, ANTI-TIE DOWN 1

1720030 POWER SUPPLY, NON 42V, NO ANTI-TIE DOWN 1
3 4501610
4 1700800
5 1705150 GEAR, DRIVE / FOR 60Hz FREQUENCY 1

1704150 GEAR, DRIVE / FOR 50Hz FREQUENCY 1

6 1705770 GEAR, DRIVEN / FOR 60Hz FREQUENCY 1

1707340 GEAR, DRIVEN / FOR 50Hz FREQUENCY 1
7 1704130 CAP 1
8 1704220 GASKET 1
9 1708460 COVER, GEAR 1

10 1708610 COVER 1
11 1708790 DRIVE WHEEL ASSEMBLY 1
12 1708840 FITTING 1
13 1709505 TAKE-UP SIDE ASSEMBLY 1
14 1709600 COVER 1
15 1709620 FLANGE 1
16 1709630 SHAFT 1
17 1710070 NUT 1
18 1710090 HANDLE ASSEMBLY 2
19 1740100 DRIVE SIDE ASSEMBLY 1
20 1740102 BEAM 1
21 3000090 LOCKWASHER 1
22 3001090 LOCKNUT 1
23 3200080 BEARING 1
24 3316050 BEARING 1
25 4111100 BLADE 1
26 7000020 PLUG 2
27 7000420 ELBOW 1
28 7007730 MALE BRANCH TEE 1
29 7036150 FITTING 1
30 7240710 WINDOW 1
31 7300200 DISCHARGE HOSE 1
32 7300756 TUBE 1
33 7310171 HOSE 1
34 7681530 O-RING 1
35 7681650 O-RING 1
36 7798170 SEAL 1
37 7798220 SEAL 1
38 8211100 SCREW 4
39 8607060 KEY 1
40 9211050 SCREW 10
41 9215080 SCREW 6
42 9215100 SCREW 5
43 9239050 SCREW 10
44 9243080 SCREW 1
45 9413070 SCREW 3

WRENCH / TOOL
TORQUE WRENCH / TOOL

1
1

Figure 5 BOM FOR MODEL BM-V-LB

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

11 OF 43

REV F: 30/12/05

12 OF 43

TAKE-UP SIDE ASSEMBLY

Figure 6 TAKE-UP SIDE ASSEMBLY

 TELEPHONE: [phone] FAX: [phone]

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

REV F: 30/12/05

ITEM PART # DESCRIPTION QTY QTY

MODEL MODEL
BM-V-LD BM-V-LB

1
2 1704670 KNOB 1 1
3

4

5
6 1704800 INSERT, ADJUSTABLE SCREW 1 1
7
8 1708470 SHAFT 1 1
9

10

11
12 1708570 BLOCK, SLIDE 1 1

13 1708590 CATCH 1 1
14
15 1709090 BLADE GUIDE ASSEMBLY 1 1
16
17 3000080 LOCKWASHER 1 1

18 3001500 LOCKNUT 1 1
19 3005280 NILOS RING 2 2
20 3650590 BEARING CUP 2 2
21 3650960 TAPER BEARING CONE 2 2
22 4505020 LABEL, DANGER/WARNING 1 1
23 5001250 RETAINING RING 1 1
24 7018150 FITTING - LUBE 1 1
25 9211050 SCREW 6 10
26 9213080 SCREW 4 4
27 9239030 SCREW 3 4
28 9239050 SCREW 3 4
29 9241030 SCREW 6 6
30 9241050 SCREW 3 3
31 9333000 SET SCREW 1 1
32 9333070 SET SCREW 2 2
33 9500090 NUT 3 4

1704560 HINGE ASSEMBLY - 1
1709590 HINGE ASSEMBLY 1 -

1704710 PLATE - 1
1709570 PLATE 1 ­1704780 GIB - 2
1709550 GIB 2 ­1704790 HOLDER, SHAFT - 1
1706360 HOLDER, SHAFT 1 -

1704810 SPACER - 2
1709560 SPACER 2 -

1708490 SLIDE - 1
1708930 SLIDE 1 ­1708530 WHEEL, TAKE-UP - 1
1708710 WHEEL, TAKE-UP 1 ­1708560 SCREW, ADJUSTABLE - 1
1709530 SCREW, ADJUSTABLE 1 -

1708600 COVER - 1
1708900 COVER 1 -

1709500 FRAME, TAKE-UP SIDE - 1
1708850 FRAME, TAKE-UP SIDE 1 -

TAKE-UP SIDE ASSEMBLY

1709201 1709505

TAKE-UP WHEEL ADJUSTMENT

TAKE-UP WHEEL, ITEM 10, MUST TURN FREELY BUT WITHOUT EXCESSIVE PLAY OR LOOSENESS. ELIMINATE
EXCESSIVE PLAY BY TIGHTENING NUT, ITEM 18, AT CENTAR OF TAKE-UP WHEEL.

Figure 7 TAKE-UP SIDE ASSEMBLY BOM

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

13 OF 43

REV F: 30/12/05

14 OF 43

DRIVE SIDE ASSEMBLY

Figure 8 DRIVE SIDE ASSEMBLY, BM-V-LD

 TELEPHONE: [phone] FAX: [phone]

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

1708071: DRIVE SIDE ASSEMBLY, BM-V-LD

ITEM PART # DESCRIPTION QTY

1 1704650 HINGE ASSEMBLY 1
2 1704660 SPACER, HINGE 1
3 1704670 KNOB 1
4 1707560 HANGER ASSEMBLY 1
5 1708081 ADAPTER 1
6 1708082 PLUG 1
7 1708550 FLANGE, REAR 1
8 1708590 CATCH 1

9 1708690 COVER, DRIVE SIDE 1
10 1708990 GASKET 1
11 1709000 SWITCH COVER 1
12 1709102 BLADE GUIDE ASSEMBLY 1
13 1709661 TUBE 1
14 1709850 FRAME, DRIVE SIDE 1
15 2000020 BOOT, PUSH BUTTON 1
16 2000080 LOCKNUT 1
17 2000130 ON-OFF PLATE 1
18 2000140 BOOT, TOGGLE SWITCH 1
19 2000700 SWITCH 1
20 2000730 SWITCH 1
21 4505030 LABEL, ELECTRIC ARROW, WARNING 1
22 5001250 RETAINING RING 1
23 7001270 BULKHEAD COUPLING 1
24 7003650 PIPE BUSHING 1
25 7004400 TEE 1
26 7007730 MALE BRANCH TEE 1
27 7011230 CONNECTOR 1
28 7011530 CONNECTOR 1
29 7011650 SPRAY NOZLE 2
30 7034070 MALE PLUG 1
31 7034090 SOCKET 1
32 7036150 FITTING 2
33 7036450 ELBOW 1
34 7300754 TUBE 1
35 8622500 DOWEL PIN 2
36 9050020 SCREW 5
37 9050040 SCREW 4
38 9209050 SCREW 4
39 9238040 SCREW 3
40 9239050 SCREW 5
41 9241050 SCREW 1
42 9333000 SET SCREW 1
43 9500090 NUT 5

Figure 9 DRIVE SIDE ASSEMBLY BOM, BM-V-LD

REV F: 30/12/05

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

15 OF 43

REV F: 30/12/05

16 OF 43

 TELEPHONE: [phone] FAX: [phone]

Figure 10 DRIVE SIDE ASSEMBLY, BM-V-LB

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

REV F: 30/12/05

1740100: DRIVE SIDE ASSEMBLY, BM-V-LB

ITEM PART # DESCRIPTION QTY

1 1704670 KNOB 1
2 1705540 HINGE ASSEMBLY 1
3 1705560 SPACER, HINGE 1
4 1707540 HANGER, MOUNTING 1
5 1707550 ANCHOR MOUNT ASSEMBLY 1
6 1708081 ADAPTER 1
7 1708082 PLUG 1
8 1708550 FLANGE, REAR 1

9 1708590 CATCH 1
10 1708780 COVER, DRIVE SIDE 1
11 1709102 BLADE GUIDE ASSEMBLY 1
12 1709380 GASKET 1
13 1709390 SWITCH COVER 1
14 1740101 FRAME, DRIVE SIDE 1
15 2000020 BOOT, PUSH BUTTON 1
16 2000080 LOCKNUT 1
17 2000130 ON-OFF PLATE 1
18 2000140 BOOT, TOGGLE SWITCH 1
19 2000700 SWITCH 1
20 2000730 SWITCH 1
21 4505030 LABEL, ELECTRIC ARROW, WARNING 1
22 5001250 RETAINING RING 1
23 7001270 BULKHEAD COUPLING 1
24 7003650 PIPE BUSHING 1
25 7004400 TEE 1
26 7007730 MALE BRANCH TEE 1
27 7011650 SPRAY NOZLE 2
28 7034070 MALE PLUG 1
29 7034090 SOCKET 1
30 7036150 FITTING 2
31 7036450 ELBOW 1
32 7300757 TUBE 1
33 8418140 SCREW 4
34 8462080 ANCHOR SHACKLE 1
35 8500200 NUT 4
36 8506180 WASHER 4
37 8622500 DOWEL PIN 2
38 9050020 SCREW 5
39 9050040 SCREW 4
40 9209050 SCREW 4
41 9238040 SCREW 3
42 9239050 SCREW 5
43 9241050 SCREW 1
44 9333000 SET SCREW 1
45 9500090 NUT 5

Figure 11 DRIVE SIDE ASSEMBLY BOM, BM-V-LB

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

17 OF 43

REV F: 30/12/05

1707560: HANGER ASSEMBLY

ITEM PART # DESCRIPTION QTY

1 1707540 HANGER, MOUNTING 1
2 1707570 ANCHOR MOUNT ASSEMBLY 1
3 8418140 SCREW 4
4 8462080 ANCHOR SHACKLE 1
5 8500200 NUT 4
6 8506180 WASHER 4

Figure 12 HANGER ASSEMBLY, BM-V-LD

TRANSMISSION

REFERENCE:

MODEL BM-V-LD

Figure 13 TRANSMISSION OVERVIEW

TRANSMISSION AND SPEED REDUCTION GEARS ARE LOCATED BEHIND DRIVE WHEEL AND CAN BE SERVICED
BY OPENING DRIVE WHEEL COVER. A ROUND GLASS SIGHT GAGE IS LOCATED BEHIND DRIVE WHEEL AND CAN
BE VIEWED WITHOUT WHEEL REMOVAL. A PLUG IS LOCATED BELOW THE SIGHT GAGE FOR DRAINING AND
ANOTHER ABOVE FOR FILLING WITH OIL. PERIODICALLY CHECK OIL LEVEL AND ADD OIL IF LEVEL BELOW
SIGHT GAGE WITH SAW IN HORIZONTAL POSITION. IF OIL LOOKS CONTAMINATED WITH WATER, GRITTY OR
BROKEN DOWN, DRAIN AND REFILL TO ABOVE SIGHT GAGE WITH HIGH QUALITY GEAR LUBRICANT. WE
RECOMMEND MOBILUBE HD 80W-90 SAE 80W-90 GEAR LUBRICANT, MULTI-PURPOSE. TRANSMISSION SHOULD
BE FLUSHED OUT AND REFILLED AFTER EVERY 200 HOURS OF OPERATION, AND WHEN OPENED UP FOR
MAINTENANCE. THE GEAR LUBRICANT USED SHOULD ALSO BE USED FOR FLUSHING OUT TRANSMISSION.

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

18 OF 43

REV F: 30/12/05

BLADE GUIDE ASSEMBLY, TAKE-UP SIDE

1709090: BLADE GUIDE ASSEMBLY, FRONT

ITEM PART # DESCRIPTION QTY

1 1708630 GUIDE HOLDER 1
2 1708640 REAR GUARD 1
3 1708650 FRONT GUARD 1
4 1709110 GUIDE 2
5 8865050 CARBID INSERT 3
6 8895100 BALL PLUNGER 1
7 9211050 SCREW 2
8 9213100 SCREW 2

9 9239050 SCREW 7
10 9501430 NUT 1
11 9620450 PIN 1
12 9870340 SCREW 1

Figure 14 BLADE GUIDE ASSEMBLY, FRONT (BM-V-LD & -LB)

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

19 OF 43

REV F: 30/12/05

BLADE GUARD ADJUSTMENTS

BLADE GUARD CONSISTS OF TWO (2) CARBIDE INSERTS, ITEM 5 FIGURE 14, THROUGH WHICH THE BLADE
PASSES, AND A BACK-UP INSERT LOCATED JUST ABOVE THE BLADE. THE INSERTS SHOULD BE CLEANED DAILY
AND INSPECTED PERIODICALLY FOR WEAR AND PROPER GAP WIDTH. THE INSERTS MAY BE ROTATED UNTIL
ALL FOUR (4) SIDES ARE WORN, AND THEN TURNED OVER FOR AN ADDITONAL FOUR (4) SIDES. THE BACK-UP
INSERT SHOULD BE ROTATED WHEN A GROOVE IS WORN INTO IT OR WEAR IS APPARENT.

GAP ADJUSTMENT:

1. REMOVE FOUR (4) SCREWS, ITEM 9, FIGURE 14.

2. CLEAN, LUBRICATE AND ROTATE OR REPLACE INSERTS.

THERE ARE TWO (2) FIBER GUIDES, ITEM 4, LOCATED UNDER INSERTS. THEY HELP KEEP BLADE FROM BEING
PULLED OUT OF GAP. REPLACE GUIDES IF EXCESSIVELY WORN.

WITH SAW IN FREE RUNNING CONDITION, CHECK BLADE'S VERTICAL LOCATION BETWEEN INSERTS.
PROPER LOCATION IS TOP OF BLADE JUST TOUCHING BACK-UP INSERT.

VERTICAL ADJUSTMENT:

1. LOOSEN TWO (2) SCREWS, ITEM 8.

2. SLIDE BLADE GUARD UP OR DOWN AS NEEDED.

3. RETIGHTEN SCREWS.

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

20 OF 43

REV F: 30/12/05

BLADE GUIDE ASSEMBLY, DRIVE SIDE

1709102: BLADE GUIDE ASSEMBLY, REAR

ITEM PART # DESCRIPTION QTY

1 1708660 GUIDE HOLDER 1
2 1708670 REAR GUARD 2
3 1708680 FRONT GUARD 1
4 1709110 GUIDE 2
5 8239050 SCREW 4
6 8865050 CARBID INSERT 3
7 8895100 BALL PLUNGER 1
8 9211050 SCREW 2

9 9213110 SCREW 2
10 9239050 SCREW 3
11 9501430 NUT 1
12 9620450 PIN 1
13 9870340 SCREW 1

REFER TO “BLADE GUIDE ASSEMBLY, TAKE-UP SIDE” (FIGURE 14) FOR ADJUSTMENT INSTRUCTIONS.

Figure 15 BLADE GUIDE ASSEMBLY, DRIVE SIDE (BM-V-LD & LB)

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

21 OF 43

REV F: 30/12/05

HANDLES

1710090; HANDLE ASSEMBLY, BM-V-L_

ITEM PART # DESCRIPTION QTY

1 1302420 HANDLE 1
2 1302430 TRIGGER 1
3 1302440 SPRING 1
4 1302450 PLUNGER 1
5 1302460 HOLDER, PLUNGER 1
6 1302470 HOLDER 2
7 1701550 SPRING 2
8 1709810 BRACKET 1

9 1709830 CAP 1
10 2000690 SWITCH 1
11 8086020 SCREW 4
12 8500580 NUT 1

Figure 16 HANDLE ASSEMBLY, BM-V-LD & LB

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

22 OF 43

MOTOR ASSEMBLY

BM-V: 2HP MOTOR

ITEM PART # DESCRIPTION QTY

1
2 1501800 COVER, MOTOR HOUSING 1
3 1705620 KEY 1
4
5 1708580 MOTOR HOUSING 1
6 3522060 BEARING 1
7 3524050 BEARING 1
8 5002120 RETAINING RING 1

9 5002440 RETAINING RING 2
10 5100980 RETAINING RING 1
11 5101180 RETAINING RING 1
12 7681300 O-RING 1
13 7902170 EXPANSION PLUG 1
14 9313040 SET SCREW 2
15 9411100 SCREW 4
16 9507100 WASHER 4

OPTIONS

OPTIONS

STATOR, CHART BELOW

ROTOR-SHAFT ASSEMBLY 1

MOTOR ASS'Y 230V, 2HP, 1PH, 60HZ, 10AMPS 1709332-230-160 2310050 1708482
MOTOR ASS'Y 115V, 2HP, 1PH, 60HZ, 20AMPS 1709332-115-160 2310050 1708482
MOTOR ASS'Y 42V, 2HP, 3PH, 50HZ, 30.0AMPS 1709330 2311580 1708481
MOTOR ASS'Y 380V, 2HP, 3PH, 50HZ, 5.1AMPS 1709320-380-350 2311640 1708481
MOTOR ASS'Y 220V, 2HP, 3PH, 50HZ, 10.2AMPS 1709320-220-350 2311640 1708481
MOTOR ASS'Y 416V, 2HP, 3PH, 50HZ, 3.0AMPS 1709290-416-350 2310510 1708481
MOTOR ASS'Y 208V, 2HP, 3PH, 50HZ, 6.0AMPS 1709290-208-350 2310510 1708481
MOTOR ASS'Y 230V, 2HP, 3PH, 50HZ, 6.0AMPS 1709310-230-350 2311600 1708481
MOTOR ASS'Y 115V, 2HP, 3PH, 50HZ, 12.0AMPS 1709310-115-350 2311600 1708481
MOTOR ASS'Y 550V, 2HP, 3PH, 60HZ, 2.5AMPS 1709300 2310540 1708481
MOTOR ASS'Y 380V, 2HP, 3PH, 60HZ, 3.6AMPS 1720110-380-360 2323060 1708481
MOTOR ASS'Y 220V, 2HP, 3PH, 60HZ, 7.4AMPS 1720110-220-360 2323060 1708481
MOTOR ASS'Y 460V, 2HP, 3PH, 60HZ, 3.0AMPS 1709290-460-360 2310510 1708481
MOTOR ASS'Y 230V, 2HP, 3PH, 60HZ, 6.0AMPS 1709290-230-360 2310510 1708481
MOTOR ASS'Y 416V, 2HP, 3PH, 60HZ, 3.3AMPS 1709280-416-360 2310500 1708481
MOTOR ASS'Y 208V, 2HP, 3PH, 60HZ, 6.6AMPS 1709280-208-360 2310500 1708481

MOTOR OPTION DESCRIPTION MOTOR ASS'Y

BM-V: 2HP MOTOR ASSEMBLY OPTIONS with STATOR

Figure 17 2HP MOTOR OPTIONS

REV F: 30/12/05

1708482 1708480 2315021-P
1708481 1708480 2315020-P

Rotor Shaft Ass’y Motor Shaft Rotor

1

STATOR

ROTOR

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

23 OF 43

1709161 1709160 2310430

Rotor Shaft Ass’y Motor Shaft Rotor

BM-V: 3HP MOTOR

ITEM PART # DESCRIPTION QTY

1
2 1501800 COVER, MOTOR HOUSING 1
3 1705620 KEY 1
4 1709161 ROTOR-SHAFT ASSEMBLY 1
5 1709170 MOTOR HOUSING 1
6 3522060 BEARING 1
7 3524050 BEARING 1
8 5002120 RETAINING RING 1

9 5002440 RETAINING RING 2
10 5100980 RETAINING RING 1
11 5101180 RETAINING RING 1
12 7681300 O-RING 1
13 7902170 EXPANSION PLUG 1
14 9313040 SET SCREW 2
15 9411100 SCREW 4
16 9507100 WASHER 4

OPTIONS

MOTOR ASS'Y 42V, 3HP, 3PH, 50HZ, 50.0AMPS 1709260 2310420
MOTOR ASS'Y 380V, 3HP, 3PH, 50HZ, 6.5AMPS 1709250-380-350 2313800
MOTOR ASS'Y 220V, 3HP, 3PH, 50HZ, 11.5AMPS 1709250-220-350 2313800
MOTOR ASS'Y 416V, 3HP, 3PH, 50HZ, 4.6AMPS 1709210-416-350 2310711
MOTOR ASS'Y 208V, 3HP, 3PH, 50HZ, 9.2AMPS 1709210-208-350 2310711
MOTOR ASS'Y 230V, 3HP, 3PH, 50HZ, 10.8AMPS 1709230-230-350 2311840
MOTOR ASS'Y 115V, 3HP, 3PH, 50HZ, 21.6AMPS 1709230-115-350 2311840
MOTOR ASS'Y 550V, 3HP, 3PH, 60HZ, 3.8AMPS 1709220 2310770
MOTOR ASS'Y 380V, 3HP, 3PH, 60HZ, 5.6AMPS 1709225-380-360 2310830
MOTOR ASS'Y 220V, 3HP, 3PH, 60HZ, 9.6AMPS 1709225-220-360 2310830
MOTOR ASS'Y 460V, 3HP, 3PH, 60HZ, 4.6AMPS 1709210-460-360 2310711
MOTOR ASS'Y 230V, 3HP, 3PH, 60HZ, 9.2AMPS 1709210-230-360 2310711
MOTOR ASS'Y 416V, 3HP, 3PH, 60HZ, 5.1AMPS 1709200-416-360 2310780
MOTOR ASS'Y 208V, 3HP, 3PH, 60HZ, 10.2AMPS 1709200-208-360 2310780

STATOR, CHART BELLOW

MOTOR OPTION DESCRIPTION MOTOR ASS'Y STATOR

BM-V: 3HP MOTOR ASSEMBLY OPTIONS with STATOR

1

Figure 18 3HP MOTOR OPTIONS

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

REV F: 30/12/05

24 OF 43

BM-V: 5HP MOTOR

ITEM PART # DESCRIPTION QTY

1

OPTIONS STATOR, CHART BELOW
2 1501800 COVER, MOTOR HOUSING 1
3 1705620 KEY 1
4 1709181 ROTOR-SHAFT ASSEMBLY 1
5 1709920 MOTOR HOUSING 1
6 3522060 BEARING 1
7 3524050 BEARING 1
8 5002120 RETAINING RING 1
9 5002440 RETAINING RING 2

10 5100980 RETAINING RING 1
11 5101180 RETAINING RING 1
12 7681300 O-RING 1
13 7902170 EXPANSION PLUG 1
14 9313040 SET SCREW 2
15 9411100 SCREW 4
16 9507100 WASHER 4

MOTOR ASS'Y 380V, 5HP, 3PH, 60HZ, 7.8AMPS 1703054-380-360 2311910
MOTOR ASS'Y 220V, 5HP, 3PH, 60HZ, 14.7AMPS 1703054-220-360 2311910
MOTOR ASS'Y 380V, 5HP, 3PH, 50HZ, 7.8AMPS 1703050-380-350 2311920
MOTOR ASS'Y 220V, 5HP, 3PH, 50HZ, 14.7AMPS 1703050-220-350 2311920
MOTOR ASS'Y 42V, 5HP, 3PH, 50HZ, 78.0AMPS 1703051 2311870
MOTOR ASS'Y 460V, 5HP, 3PH, 60HZ, 7.0AMPS 1703021-460-360 2310750
MOTOR ASS'Y 230V, 5HP, 3PH, 60HZ, 14.0AMPS 1703021-230-360 2310750
MOTOR ASS'Y 230V, 5HP, 3PH, 50HZ, 14.5AMPS 1703042-230-350 2311450
MOTOR ASS'Y 115V, 5HP, 3PH, 50HZ, 29.0AMPS 1703042-115-350 2311450

MOTOR OPTION DESCRIPTION MOTOR ASS'Y STATOR

BM-V: 5HP MOTOR ASSEMBLY OPTIONS with STATOR

Figure 19 5HP MOTOR OPTIONS

REV F: 30/12/05

1709181 1709180 2315260

Rotor Shaft Ass’y Motor Shaft Rotor

1

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

25 OF 43

POWER SUPPLY OPTIONS

1720000: POWER SUPPLY, 42V, ATD

ITEM PART # DESCRIPTION QTY

1 1708730 GASKET 1
2 1709480 COVER, WIRE BOX, 42V, ATD 1
3 2001090 POWER CORD 1
4 2008200 CABLE CONNECTOR 1
5 2008210 CORD GRIP 1
6 2009120 TIMER 1
7 9209240 SCREW 4

REV F: 30/12/05

Figure 20 POWER SUPPLY, 42V, with ANTI-TIEDOWN

1720010: POWER SUPPLY, 42V, NO ATD

ITEM PART # DESCRIPTION QTY

1 1708730 GASKET 1
2 1709480 COVER, WIRE BOX 1
3 2007030 POWER CORD 1
4 2008200 CABLE CONNECTOR 1
5 2008210 CORD GRIP 1
6 9209240 SCREW 4

Figure 21 POWER SUPPLY, 42V, without ANTI-TIEDOWN

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

26 OF 43

REV F: 30/12/05

1720020: POWER SUPPLY, NON 42V, ANTI-TIE DOWN

ITEM PART # DESCRIPTION QTY

1 1708730 GASKET 1
2 1709460 COVER, WIRE BOX 1
3 2001080 POWER CORD 1
4 2001610 SOCKET, MALE 1
5 2001620 SOCKET, FEMALE 1
6 2008180 CABLE CONNECTOR 1
7 2008220 CORD GRIP 1
8 2009120 TIMER 1
9 9209240 SCREW 4

Figure 22 POWER SUPPLY, NON 42V, with ANTI-TIEDOWN

1720030: POWER SUPPLY, NON 42V, NO ATD

ITEM PART # DESCRIPTION QTY

1 1000050 POWER CORD w/MALE PLUG 1
2 1708730 GASKET 1
3 1709460 COVER, WIRE BOX 1
4 2001620 SOCKET, FEMALE 1
5 2008180 CABLE CONNECTOR 1
6 2008220 CORD GRIP 1
7 9209240 SCREW 4

POWER CORD 1000050: POWER CORD 20FT LONG (2001240) + MALE PLUG (2001610)

Figure 23 POWER SUPPLY, NON 42V, without ANTI-TIEDOWN

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

27 OF 43

REV F: 30/12/05

1720005: POWER SUPPLY, SINGLE PHASE 115V

ITEM PART # DESCRIPTION QTY

1 1708730 GASKET 1
2 1709460 COVER, WIRE BOX 1
3 2001240 POWER CORD 1
4 2008180 CABLE CONNECTOR 1
5 2008220 CORD GRIP 1
6 2309110 PACITOR START MOTOR 1
7 2309530 CAPACITOR 1
8 9209240 SCREW 4

Figure 24 POWER SUPPLY, SINGLE PHASE, 115V

1720006: POWER SUPPLY, SINGLE PHASE 230V

ITEM PART # DESCRIPTION QTY

1 1708730 GASKET 1
2 1709460 COVER, WIRE BOX 1
3 2001080 POWER CORD 1
4 2008180 CABLE CONNECTOR 1
5 2008220 CORD GRIP 1
6 2309110 PACITOR START MOTOR 1
7 2309530 CAPACITOR 1
8 9209240 SCREW 4

Figure 25 POWER SUPPLY, SINGLE PHASE, 230V

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

28 OF 43

WIRING DIAGRAMS

REV F: 30/12/05

SINGLE PHASE – 230V

CONTROL VOLTAGE MOTOR OPTION 3-POLE

CONTACTOR

220V MOTOR 230V, 60HZ, 10AMPS, 2HP 2020032 2309160

NOTES:

1. DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON.

2. ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN.

3. THE CAPACITOR AND THE SWITCH – CAP. START MOTOR AR MOUNTED INSIDE THE MAGNETIC PANEL

BOX.

4. THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE “OFF” POSITION.

5. MOTOR #7 LEAD IS UNUSED AND SHOULD BE INSULATED AND TAPED SEPERATELY.

6. THE GROUND WIRE (GREEN) OF THE POWER CABLE IS CONNECTED TO THE FRAME OF THE MACHINE.

7. TO REVERSE DIRECTION, REVERSE MOTOR WIRES #5 AND #6.

OVERLOAD RELAY

Figure 26 WIRING DIAGRAM – SINGLE PHASE – 230V

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

29 OF 43

REV F: 30/12/05

SINGLE PHASE – 115V

CONTROL VOLTAGE MOTOR OPTION 3-POLE CONTACTOR OVERLOAD RELAY

115V MOTOR 115V, 60HZ, 20.0AMPS, 2HP 2020036 2309190

NOTES:

1. DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON.

2. ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN.

3. THE CAPACITOR AND THE SWITCH – CAP. START MOTOR AR MOUNTED INSIDE THE MAGNETIC PANEL

BOX.

4. THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE “OFF” POSITION.

5. MOTOR #7 LEAD IS UNUSED AND SHOULD BE INSULATED AND TAPED SEPERATELY.

6. THE GROUND WIRE (GREEN) OF THE POWER CABLE IS CONNECTED TO THE FRAME OF THE MACHINE.

7. TO REVERSE DIRECTION, REVERSE MOTOR WIRES #5 AND #6.

Figure 27 WIRING DIAGRAM – SINGLE PHASE – 115V

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

30 OF 43

REV F: 30/12/05

1. DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON.

2. ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN.

3. THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE “OFF” POSITION.

To obtain the correct Kentmaster part number for 3-pole contactor and overload relay,
please contact the Kentmaster representative.

Figure 28 WIRING DIAGRAM – 3 PHASE – DIFFERENT CONTROL AND MOTOR VOLTAGE –

without Anti-Tie Down

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

31 OF 43

REV F: 30/12/05

1. DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON.

2. ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN.

3. THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE “OFF” POSITION.

To obtain the correct Kentmaster part number for 3-pole contactor and overload relay,
please contact the Kentmaster representative.

Figure 29 WIRING DIAGRAM – 3 PHASE – SAME CONTROL AND MOTOR VOLTAGE –without

Anti-Tie Down

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

32 OF 43

L N

REV F: 30/12/05

1. DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON.

2. ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN.

3. THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE “OFF” POSITION.

To obtain the correct Kentmaster part number for 3-pole contactor and overload relay,
please contact the Kentmaster representative.

Figure 30 WIRING DIAGRAM – 3 PHASE – DIFFERENT CONTROL AND MOTOR VOLTAGE –

with Anti-Tie Down

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

33 OF 43

REV F: 30/12/05

1. DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON.

2. ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN.

3. THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE “OFF” POSITION.

To obtain the correct Kentmaster part number for 3-pole contactor and overload relay,
please contact the Kentmaster representative.

Figure 31 WIRING DIAGRAM – 3 PHASE – SAME CONTROL/TRIGGER AND MOTOR VOLTAGE

with Anti-Tie Down

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

34 OF 43

REV F: 30/12/05

Figure 32 ELECTRIC MOTOR LEAD HOOKUP DIAGRAM 3 PHASE MOTOR

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

35 OF 43

[ENGLISH]

GENERAL INFORMATION

BM-V-LB

REV F: 30/12/05

BM-V-LD

MODELS

BM-V-LB LOIN DROPPER (1740000)
BM-V-LD LOIN DROPPER (1708070)

________________________________________________________________________________

SERVICE CENTERS

KENTMASTER LTD. (U.K) KENTMASTER MFG. CO., INC.

16 AVONBANK INDUSTRIAL CENTRE 1801 SOUTH MOUNTAIN AVE.
WEST TOWN ROAD MONROVIA, CALIFORNIA 91016
AVONMOUTH - BRISTOL BS11 9DE UNITED STATES OF AMERICA

UNITED KINGDOM

TELEPHONE: ++ 44- (0) 117- 9235035  TELEPHONE: [phone]

FAX: ++ 44- (0) 117- 9829010 FAX: [phone]

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

36 OF 43

REV F: 30/12/05

You have purchased a powerful tool that, if misused, can cause severe
injury and harm to your employees. You must instruct your employees in
the safe and proper use of this tool and to follow the safety procedures
and instructions that have been supplied by the manufacturer of this tool.
Please follow the following instructions.

1. Instruct tool operators to test the tool each day before using it to be sure it does not malfunction.

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

Remove and repair any tool that malfunctions.

2. Instruct tool operators to immediately stop using a tool that malfunctions or is defective.

3. Instruct personnel to immediately remove all tools that malfunction. Be sure to disconnect tool from

power supply.

4. Instruct all personnel to stay clear of tool, and not to stand or walk in front of, or next to tool when in
use.

5. Point out to all personnel the dangers related to the misuse of tool and the importance of following
safety procedures and instructions.

6. Do not make, or allow others to make, alterations or modifications to this tool.

Replace all lost or illegible labels.

7. Follow all safety, installation and maintenance instructions provided with this tool. Establish proper
safety procedures in accordance with local and national requirements to prevent accidental energizing
of tool that can cause injuries.

8. If this tool is sold or change in ownership takes place, you must provide the new owner all safety
instructions, notices and maintenance instructions you were originally provided. You can obtain
additional copies of the instructions from Kentmaster, free of charge upon request.

9. Give copies of instructions to: (A) Tool Operators

(B) Maintenance Supervisor
(C) Clean-up Supervisor

NOTICE TO EMPLOYER AND PURCHASER OF TOOL

NOTICE TO SAFETY DIRECTOR

 TELEPHONE: [phone] FAX: [phone]

Page 37 of 43

REV F: 30/12/05

GENERAL INFORMATION

__________________________________________________________________________________________

COVERING: SAFETY PRECAUTIONS AND PLACING INTO SERVICE

ELECTRICAL POWERED LOIN DROPPER

__________________________________________________________________________________________

READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING

THIS TOOL

_____________________________________________________________________________________________________

IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THIS INFORMATION INTO THE HANDS OF THE OPERATOR.

_____________________________________________________________________________________________________

PLACING INTO SERVICE

_____________________________________________________________________________________________________

= Hazards or unsafe practices which could result in severe personal injury, death or

! WARNING

substantial property damage.

= Hazards or unsafe practices which could result in minor personal injury, product or

! CAUTION

property damage.

= Important installation, operation or maintenance information.

! NOTICE

Installation, adjustment repair and maintenance of this tool must be made by trained
and qualified personnel.

Always disconnect power supply from tool before:
(A) Installing or removing blade from tool.
(B) Making repairs or adjustments to the tool.
(C) performing maintenance or cleanup work.

ALL ELECTRICAL WIRING MUST BE DONE BY A LICENSED ELECTRICIAN IN
ACCORDANCE WITH THE NATIONAL, STATE AND LOCAL ELECTRICAL CODES.

! WARNING

(REFER TO NAMEPLATE ON TOOL FOR PROPER POWER CONFIGURATION).

1. A BALANCER IS REQUIRED FOR OPERATION AND USE OF THIS TOOL. WEIGHT OF TOOL MUST FALL WITHIN

WEIGHT RANGE OF BALANCER. "AIR-BALANCERS" WHICH OPERATE ON COMPRESSED AIR, ARE HIGHLY
RECOMMENDED FOR USE WITH BANDMASTER SAWS. THEY PROVIDE LONG TRAVEL AND VERY SMOOTH,
UNIFORM RISE AND FALL. THEY CAN BE INTERFACED WITH THE OPERATION OF THE SAW.

2. INSTALL BALANCER ABOVE WORK AREA. BALANCER MUST HAVE SUFFICIENT VERTICAL TRAVEL SO
OPERATOR CAN REACH ENTIRE WORK AREA WITH TOOL WITHOUT STRAIN.

3. ADJUST BALANCER ACCORDING TO THE OPERATOR'S PREFERENCE AND COMFORT.

4. TOOL REQUIRES GREASING AFTER EVERY 40 HOURS OF OPERATION. GREASE USING KENTMASTER

GREASE (PART NO. 7903070).
WE STRONGLY SUGGEST THAT AN ADDITIONAL SAFETY CHAIN BE USED TO CHAIN

BALANCER TO OVERHEAD TROLLEY. THIS ADDITIONAL MEASURE OF SAFETY WILL

! WARNING

HELP REDUCE INJURIES.

! WARNING

! WARNING

INSTALLATION INSTRUCTIONS

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 38 of 43

REV F: 30/12/05

OPERATING INSTRUCTIONS

ONLY TRAINED PERSONNEL ARE TO OPERATE THIS TOOL.

! WARNING

1. HOLD TOOL FIRMLY AT BOTH TRIGGER HANDLES. SQUEEZE TRIGGERS SIMULTANEOUSLY T O ACTIVATE

TOOL.

2. START CUT WITH SAW NOSE POINTED UP AT AN ANGLE.

3. LEVEL SAW TO HORIZONTAL POSITION IN LOIN AREA.

4. POINT NOSE OF SAW AT DOWNWARD ANGLE IN CHUCK AND NECK AREA.

5. A BEGINNING SPLITTER CAN MARK BACKFAT OF BEEF WITH A KNIFE TO HELP GUIDE SAW DOWN CENTER OF

BACKBONE AND UNTIL OPERATOR IS FAMILIAR WITH SPLITTING PROCEDURE.

6. DO NOT EXERT EXCESSIVE PRESSURE. ALLOW TIME FOR THE TOOL TO CUT.

7. PUSH SAW FORWARD SO THAT GUARDS, ITEMS 1 AND 2, FIGURE 1, RIDE AGAINST BEEF. THIS HELPS STEADY

SAW IN CUT AND HELPS ELIMINATE BLADE JUMPING AND CHATTERING.

MAINTENANCE

ONLY TRAINED AND QUALIFIED PERSONNEL ARE TO PERFORM MAINTENANCE

! WARNING

AND SERVICE TO THIS TOOL.

1. FOLLOW PROCEDURE NO. 4 OF INSTALLATION INSTRUCTIONS.

BLADE REMOVAL AND CLEANING.

ALWAYS DISCONNECT POWER SUPPLY FROM TOOL BEFORE INSTALLING OR

! WARNING

REMOVING BLADE FROM TOOL.

ALWAYS WEAR WIRE MESH GLOVES WHEN INSTALLING OR REMOVING BLADES FROM TOOL.

! WARNING

1. REMOVE PAPER WRAPPER FROM BLADE.

2. OPEN COVERS, FIGURE 1, ITEMS 3 AND 4.

3. INSTALL TORQUE WRENCH INTO SCREW, FIGURE 1, ITEM 5, AND TURN COUNTER-CLOCKWISE (CCW).

THIS ALLOWS TAKE-UP WHEEL AND SLIDE, ITEM 7 AND 8, TO RETRACT.

4. SLIDE TAKE-UP WHEEL TO RIGHT.

5. HOLD BLADE, WITH TEETH FACING AWAY FROM YOU, AND INSTALL INTO SLOT OF BEAM, CONTINUING AROUND

AND OVER THE TAKE-UP AND DRIVE WHEELS.

6. TURN TORQUE WRENCH CLOCKWISE (CW) TO ELIMINATE BLADE SLACK AND TIGHTEN TAKE-UP WHEEL
AGAINST BLADE (TORQUE WRENCH IS PRESET AT FACTORY AND WILL SLIP AFTER PLACING PROPER TENSION
ON BLADE).

7. TWIST BLADE 90 DEGREES AT BLADE GUARDS AND INSERT BLADE INTO SLOTS WITH TEETH FACING

DOWNWARD.

8. TURN DRIVE WHEEL, ITEM 9, SLOWLY BY HAND, ONE OR TWO TURNS TO CHECK TRACKING OF BLADE ON

WHEELS.

9. RETORQUE AGAIN UNTIL TORQUE WRENCH SLIPS.

SERVICE

1. KEEP GOOD RECORDS OF ALL SERVICE ACTIVITY AND INCLUDE TOOL IN YOUR PREVENTIVE MAINTENANCE

PROGRAM.

2. USE ONLY GENUINE KENTMASTER REPLACEMENT PARTS TO ASSURE PROPER PERFORMANCE OF TOOL.

3. CONTACT THE KENTMASTER SUPPLIER NEAREST YOU FOR PARTS

AND CUSTOMER SERVICE INFORMATION.

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 39 of 43

REV F: 30/12/05

DECLARATION OF CONFORMITY

DECLARATION OF CONFORMITY

DECLARATION DE CONFORMITE -DECLARACION DE CONFORMIDAD- ERKLARUNG BEZUGLICH EINHALTUNG DER VORSCHRIFTEN

DICHIARAZIONE DI CONFORMITA . CONFORMITEITSVERKLARING

MANUFACTURED BY: KENTMASTER MFG CO., INC.

FABRIQUE PAR:

1801 SOUTH MOUNTAIN AVE.

FABRICADA POR:

MONROVIA, CALIFORNIA 91016

HERGESTELLTVON:
FABBRICATO DA:

UNITED STATES OF AMERICA

VERVAARDIGD DOOR:

TELEPHONE [phone] FAX [phone]

TYPE / SERIES: LOIN DROPPER

TYPE / SERIE:
TIPO / SERIE:
TYP / SERIE:
TIPO / SERIE:
TYPE / SERIE:

MODEL: BM-V-LD, BM-V-LB

MODELE:
MODELO:
MODELL:
MODELLO:
MODEL:

SERIAL NO. RANGE: XXXXX
N SERIE: • GAMA DE No. DE SERIE: • SERIEN-NR.-BEREICH: • NUMERI DI SERIE: • SERIENUMMERS:

This product complies with the following European Community Directives:
Ce produit est conforme aux directives de la Communaute europeenne suivantes:

Este producto cumple con las siguientes Directrices de la Comunidad Europea:
Dieses Produkt erfullt die folgenden Vorschriften der Europaischen Gemeinschaft:
Questo prodotto e conforme alle seguenti direttive CEE:
Dit produkt voldoet aan de volgende EG-richtlijnen:

89/392/EEC, 91/368/EEC, 93/44/EEC, 93/68/EEC

_______________________________________________________________________
The following Standards were used to verify compliance with the Directives:

Les normes suivantes ont ete utilisees pour verifier la conformite avec les Directives:
Las siguientes Normas se usaron para verificar el cumplimiento de las Directrices:
Folgende Normen wurden angewandt, um erfullung der vorschriften zu bestatigen:
Per verificare la conformita del prodotto alle direttive sono stati usati i seguenti standard:
De volgende normen zijn gebruikt om naleving van de richtlijnen te bevestigen:

EN 292
_______________________________________________________________________________________________________

RALPH KARUBIAN MONROVIA, CA. U.S.A

Approved by: ________________________ Date: AUG - 1 - 1995

(Engineering Manager) (Directeur technique) (gerente de ingenieria) (verantwortlicher Konstruktionsleiter) (Responsabile tecnico) (ondersteunend technisch mangar)

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 40 of 43

REV F: 30/12/05

Kentmaster Worldwide Location

Kentmaster Equipment (Aust) PTY.LTD.
Unit 2,24 Central Court
Browns Plains Qld. 4118

Australia

Telephone: [phone]
Fax: [phone]
[email protected]
Kentmaster do Brasil, Ltda.
Av. Dr. Joao Teodoro No. 805
Bairro De Vila Rezende

13405-240 Piracicaba, SP,
Brazil

Telephone #1: (019) 3 413 3113
Telephone #2: [phone]

Fax: [phone]
[email protected]
Kentmaster (IRL) LTD.
Benamore, Dublin Road.
Roscrea,
CO, Tipperary,
Ireland

Telephone: [phone]
Fax: [phone]
[email protected]
Kentmaster Equipment (NZ) LTD.
5 Cooper Street

Havelock North
New Zealand

Telephone #1: (64) 6 8777 857
Telephone #2: 0800 KENTMASTER
Fax: [phone]

[email protected]

Kentmaster South Africa (PTY) LTD.
Johannesburg - S. Africa

Unit 54 Sunnyrock Park
Sunrock Close, Germiston
South Africa

Telephone: [phone]
Fax: [phone]
[email protected]
Kentmaster (UK ) LTD.
Unit 16 Avonbank Ind. Centre

West Town Rd, Avonmouth-Bristol,
BS11 9DE
England

Telephone: [phone]
Fax: [phone]
[email protected]
Kentmaster Mfg. Co., Inc.
1801 South Mountain Ave.
Monrovia, CA, 91016
USA

Telephone #1: [phone]
Telephone #2: [phone]
Fax: [phone]
[email protected]
Kentmaster Omaha
4417 South 139th Street
Omaha, NE, 68137
USA

Telephone #1: [phone]
Telephone #2: [phone]
Fax: [phone]
[email protected]

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 41 of 43

REV F: 30/12/05

INDEX

OPERATING AND SAFETY INSTRUCTIONS.....................................................................................................................................2

OPERATING INSTRUCTIONS........................................................................................................................................................3

MAINTENANCE.................................................................................................................................................................................3

CLEANING AND STERILIZING SAW ...........................................................................................................................................4

WATER CONNECTION....................................................................................................................................................................4

TORQUE WRENCH CALIBRATION.............................................................................................................................................4

HANGER ..............................................................................................................................................................................................5

TROUBLE SHOOTING HINTS: ............................................................................................................................................................6

SERVICE..................................................................................................................................................................................................7

PARTS BOOK...........................................................................................................................................................................................7

MODELS MAIN ASSEMBLIES........................................................................................................................................................7

TAKE-UP SIDE ASSEMBLY..........................................................................................................................................................12

DRIVE SIDE ASSEMBLY...............................................................................................................................................................14

BLADE GUIDE ASSEMBLY, TAKE-UP SIDE ............................................................................................................................19

BLADE GUIDE ASSEMBLY, DRIVE SIDE..................................................................................................................................21

HANDLES..........................................................................................................................................................................................22

MOTOR ASSEMBLY.......................................................................................................................................................................23

POWER SUPPLY OPTIONS...........................................................................................................................................................26

WIRING DIAGRAMS............................................................................................................................................................................29

GENERAL INFORMATION.................................................................................................................................................................38

INSTALLATION INSTRUCTIONS ...............................................................................................................................................38

OPERATING INSTRUCTIONS......................................................................................................................................................39

MAINTENANCE...............................................................................................................................................................................39

SERVICE............................................................................................................................................................................................39

DECLARATION OF CONFORMITY...................................................................................................................................................40

Kentmaster Worldwide Location............................................................................................................................................................41

INDEX.....................................................................................................................................................................................................42

FIGURES - INDEX................................................................................................................................................................................43

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 42 of 43

REV F: 30/12/05

FIGURES - INDEX

Figure 1 BM-V-LD....................................................................................................................................................................................5

Figure 2 MODELS BM-V-LD ..................................................................................................................................................................8

Figure 3 BOM FOR MODELS BM-V-LD................................................................................................................................................9

Figure 4 MODEL BM-V-LB...................................................................................................................................................................10

Figure 5 BOM FOR MODEL BM-V-LB................................................................................................................................................11

Figure 6 TAKE-UP SIDE ASSEMBLY..................................................................................................................................................12

Figure 7 TAKE-UP SIDE ASSEMBLY BOM........................................................................................................................................13

Figure 8 DRIVE SIDE ASSEMBLY, BM-V-LD....................................................................................................................................14

Figure 9 DRIVE SIDE ASSEMBLY BOM, BM-V-LD..........................................................................................................................15

Figure 10 DRIVE SIDE ASSEMBLY, BM-V-LB..................................................................................................................................16

Figure 11 DRIVE SIDE ASSEMBLY BOM, BM-V-LB........................................................................................................................17

Figure 12 HANGER ASSEMBLY, BM-V-LD.......................................................................................................................................18

Figure 13 TRANSMISSION OVERVIEW.............................................................................................................................................18

Figure 14 BLADE GUIDE ASSEMBLY, FRONT (BM-V-LD & -LB).................................................................................................19

Figure 15 BLADE GUIDE ASSEMBLY, DRIVE SIDE (BM-V-LD & LB).........................................................................................21

Figure 16 HANDLE ASSEMBLY, BM-V-LD & LB.............................................................................................................................22

Figure 17 2HP MOTOR OPTIONS.........................................................................................................................................................23

Figure 18 3HP MOTOR OPTIONS.........................................................................................................................................................24

Figure 19 5HP MOTOR OPTIONS.........................................................................................................................................................25

Figure 20 POWER SUPPLY, 42V, with ANTI-TIEDOWN...................................................................................................................26

Figure 21 POWER SUPPLY, 42V, without ANTI-TIEDOWN..............................................................................................................26

Figure 22 POWER SUPPLY, NON 42V, with ANTI-TIEDOWN.........................................................................................................27

Figure 23 POWER SUPPLY, NON 42V, without ANTI-TIEDOWN....................................................................................................27

Figure 24 POWER SUPPLY, SINGLE PHASE, 115V ..........................................................................................................................28

Figure 25 POWER SUPPLY, SINGLE PHASE, 230V ..........................................................................................................................28

Figure 26 WIRING DIAGRAM – SINGLE PHASE – 230V .................................................................................................................29

Figure 27 WIRING DIAGRAM – SINGLE PHASE – 115V .................................................................................................................30

Figure 28 WIRING DIAGRAM – 3 PHASE – DIFFERENT CONTROL AND MOTOR VOLTAGE –without Anti-Tie Down........31

Figure 29 WIRING DIAGRAM – 3 PHASE – SAME CONTROL AND MOTOR VOLTAGE –without Anti-Tie Down..................32

Figure 30 WIRING DIAGRAM – 3 PHASE – DIFFERENT CONTROL AND MOTOR VOLTAGE –with Anti-Tie Down.............33

Figure 31 WIRING DIAGRAM – 3 PHASE – SAME CONTROL/TRIGGER AND MOTOR VOLTAGE with Anti-Tie Down......34

Figure 32 ELECTRIC MOTOR LEAD HOOKUP DIAGRAM 3 PHASE MOTOR.............................................................................35

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 43 of 43