KENTMASTER 500E Operating Instructions Manual

REV E: 04/08

500E

INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK

IMPORTANT: READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR

SERVICING THIS TOOL.

TOOL DATA

MODEL: KENTMASTER 500E
ASSEMBLY NO: 1050000
TYPE: ELECTRICAL OPERATED
NET WEIGHT: 80 LB (36 KG)
MOTOR HORSEPOWER: 1HP / 50Hz, 60Hz

BEEF BRISKET SAW - ELECTRIC

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 1 of 18

REV E: 04/08

= Hazards or unsafe practices which could result in severe personal injury,

! WARNING

death or substantial property damage.

= Hazards or unsafe practices which could result in minor personal injury,

! CAUTION

product or property damage.

= Important installation, operation or maintenance information.

! NOTICE

OPERATING AND SAFETY INSTRUCTIONS

! WARNING

DO NOT OPERATE THIS TOOL UNTIL YOU HAVE READ AND UNDERSTOOD THE SAFETY
INSTRUCTIONS AND OPERATING MANUALS.

! WARNING

DO NOT OPERATE THIS TOOL UNTIL YOU HAVE RECEIVED TRAINING IN THE HANDLING,
OPERATION AND USE OF THIS TOOL.

! WARNING

STOP USING A MALFUNCTIONING OR DEFECTIVE TOOL IMMEDIATELY. REPORT ANY

PROBLEMS OR DEFECTS TO YOUR SUPERVISOR FOR REMOVAL OF THE TOOL FROM

SERVICE.

! WARNING

DO NOT ATTEMPT TO REPAIR THE TOOL YOURSELF.

! WARNING

DO NOT ALLOW UNAUTHORIZED PERSONS TO USE TOOL.

! WARNING

REMOVE AND DISCONNECT POWER FROM THE TOOL WHEN TOOL IS LEFT
UNATTENDED OR IS NOT IN USE.

! WARNING

NEVER TIE DOWN, BYPASS, ALTER OR MODIFY THE ACTIVATING SWITCHES OR
TRIGGERS OF THIS TOOL.

! WARNING

NEVER MAKE ALTERATIONS OR MODIFICATIONS TO THIS TOOL.

! WARNING

BE CONSTANTLY AWARE AND ALERT FOR UNSAFE CONDITIONS AND REPORT THEM
IMMEDIATELY TO YOUR SUPERVISOR.

! WARNING

NEVER PLACE YOUR HAND OR ANY PART OF YOUR BODY IN THE CUTTING PATH OF
THE TOOL.

! WARNING

NEVER ALLOW ANYONE ELSE TO PLACE THEIR HANDS OR ANY PART OF THEIR BODY IN
THE CUTTING PATH OF THE TOOL.

! WARNING

DO NOT ACTIVATE CONTROL SWITCHES OR TRIGGERS OF THIS TOOL UNLESS YOU
INTEND TO TEST OR OPERATE THIS TOOL.

! WARNING

DO NOT USE THIS TOOL FOR ANY PURPOSE OTHER THAN IT’S INTENDED PURPOSE.

! CAUTION

WHEN OPERATING THIS TOOL WEAR THE PROTECTIVE GEAR AND SAFETY EQUIPMENT
SUPPLIED TO YOU.

! WARNING

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

THE NOISE EMISSION (SOUND PRESSURE LEVEL) AT THE WORKSTATION MAY EXCEED
80 dB (A). EAR AND SOUND PROTECTION GEAR IS REQUIRED.

 TELEPHONE: [phone] FAX: [phone]

Page 2 of 18

REV E: 04/08

OPERATING INSTRUCTIONS

! WARNING

ONLY TRAINED PERSONNEL ARE TO OPERATE THIS TOOL.

1. TO ENSURE TOOL IS OPERATING PROPERLY, PERFORM FOLLOWING STEPS AT START OF EACH

SHIFT:

• MAKE SURE TOOL MOVES UP AND DOWN FREELY WHILE HANGING FROM BALANCER OVERHEAD.

• WITH POWER TO TOOL TURNED ON, TEST TRIGGER FOR PROPER OPERATION.

2. TO PERFORM WORK, HOLD TOOL FIRMLY AT BOTH HANDLES. SQUEEZE TRIGGERS TO ACTIVATE

TOOL.

3. POSITION TOOL AND PERFORM CUTTING OPERATION.

BLADE REMOVAL AND CLEANING.

ALWAYS DISCONNECT POWER SUPPLY FROM TOOL BEFORE INSTALLING OR

! WARNING

REMOVING BLADE FROM TOOL.
! WARNING

ALWAYS WEAR WIRE MESH GLOVES WHEN INSTALLING OR REMOVING BLADE FROM
TOOL.

1. REMOVE NUT AND BOLT (ITEM NO. 2, 4, FIG. NO. 1).

2. REMOVE BLADE (ITEM NO. 1, FIG. NO. 1).

3. CLEAN ALL PARTS REMOVED WITH SOAP AND

WATER.

4. SHARPEN OR REPLACE BLADES WHEN NECESSARY.

5. REASSEMBLE IN REVERSE ORDER.

Figure 1 MODEL 500E – BLADE REPLACMENT

SERVICE

1. KEEP GOOD RECORDS OF ALL SERVICE ACTIVITY AND INCLUDE TOOL IN PREVENTIVE
MAINTENANCE PROGRAM.

2. USE ONLY GENUINE KENTMASTER REPLACEMENT PARTS TO ASSURE PROPER PERFORMANCE OF
TOOL.

3. CONTACT THE KENTMASTER SUPPLIER NEAREST YOU FOR PARTS AND CUSTOMER SERVICE
INFORMATION.

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 3 of 18

REV E: 04/08

INSTALLATION INSTRUCTIONS

ALL ELECTRICAL WIRING MUST BE DONE BY A LICENSED ELECTRICIAN IN
ACCORDANCE WITH THE NATIONAL, STATE AND LOCAL ELECTRICAL CODES.

! WARNING

(REFER TO NAMEPLATE ON TOOL FOR PROPER POWER CONFIGURATION).

1. A BALANCER IS REQUIRED FOR OPERATION AND USE OF THIS TOOL. WEIGHT OF TOOL MUST FALL WITHIN

WEIGHT RANGE OF BALANCER

2. INSTALL BALANCER ABOVE WORK AREA. BALANCER MUST HAVE SUFFICIENT VERTICAL TRAVEL SO
OPERATOR CAN REACH ENTIRE WORK AREA WITH TOOL WITHOUT STRAIN

3. ADJUST BALANCER ACCORDING TO THE OPERATOR'S PREFERENCE AND COMFORT.
WE STRONGLY SUGGEST THAT AN ADDITIONAL SAFETY CHAIN BE USED TO CHAIN

! WARNING

BALANCER TO OVERHEAD TROLLEY. THIS ADDITIONAL MEASURE OF SAFETY WILL
HELP REDUCE INJURIES.

MAINTENANCE

ONLY TRAINED AND QUALIFIED PERSONNEL ARE TO PERFORM MAINTENANCE

! WARNING

AND SERVICE TO THIS TOOL.
OIL LUBRICATION: THE FAT OF THE CARCASS PROVIDES SUFFICIENT LUBRICATION FOR THE BLADE GUIDES AND

OIL LUBRICATION OF BLADE IS NOT NECESSARY WHEN MACHINE IS IN OPERATION.
SAW SHAFT REQUIRES CONTINUOUS LUBRICATION. VERIFY OILER CUP AT THE END OF EACH SHIFT AND ENSURE

THAT THE OILER CONTAINS LIGHT-WEIGHT, FOOD-GRADE OIL, ENOUGH TO COVER BOTTOM OF OILER CUP.

RECOMMENDED LUBRICANT CAN BE PURCHASED FROM “KENTMASTER MFG., CO., INC.”

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 4 of 18

REV E: 04/08

PARTS BOOK

“500E” MAIN ASSEMBLY

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Figure 2 MODEL “500E"

Page 5 of 18

REV E: 04/08

1050000: 500E - BRISKET SAW

ITEM PART # DESCRIPTION QTY ITEM PART # DESCRIPTION QTY

1 10512__ MOTOR ASSEMBLY OPTIONS 1 31 3601200 BEARING 1

1002420 POWER CORD ASSEMBLY, NON 42V 1 32 4100170 BLADE, 13.6" LONG 1

2

1002430 POWER CORD ASSEMBLY, 42V 1 33 5001370 RETAINING RING 2
3 1052010 HOUSING 1 34 5001500 RETAINING RING 2
4 1052040 BOTTOM COVER 1 35 5002060 RETAINING RING 2
5 1052120 BALANCE 1 36 5100780 RETAINING RING 1
6 1052140 GUIDE - SAW SHAFT 1 37 6000620 SPRING 1
7 1052150 SHAFT - CONNETING ROD 1 38 6001660 WASHER 2
8 1052220 SAW SHAFT 1 39 7236030 OILER 1
9 1052380 COVER 1 40 7681220 O-RING 2

10 1052390 TRIGGER 1 41 7681330 O-RING 1
11 1052420 HANGER 1 42 8023060 SCREW 2
12 1052430 BRACKET 1 43 8029020 SCREW 2
13 1052640 STEP BOLT 1 44 8029040 SCREW 6
14 1052680 BLADE GUIDE 1 45 8071200 SCREW 4
15 1052710 FORWARD HANDLE 1 46 8081020 SCREW 4
16 1052760 SEAL 2 47 8211220 SCREW 4
17 1052840 WASHER 2 48 8410040 SCREW 1
18 1052880 COVER - WIRE BOX 1 49 8411080 SCREW 4
19 1052920 INSULATION PLATE 1 50 8413080 SCREW 2
20 1053000 PLATE, SPRING BACK UP 1 51 8413120 SCREW 5
21 1053010 ROD ACTUATOR 1 52 8415600 SCREW 1
22 1053220 GASKET 1 53 8500100 NUT 1
23 1053230 GASKET 1 54 8500130 NUT 1
24 1070040 CONNECTING ROD 1 55 8506160 WASHER 1
25 1071324 LUBRICATING FELT 1 56 8506600 WASHER 4
26 2000040 NAME PLATE 1 57 8507090 WASHER 4
27 2000180 SWITCH 1 58 8507100 WASHER 4
28 3000020 WASHER 1 59 8507150 WASHER 6
29 3001020 NUT 1 60 8611600 PIN 1
30 3304040 BEARING 1 61 8613180 PIN 1

Figure 3 BOM FOR MODEL “500E”

1052140: GUIDE - SAW SHAFT

ITEM PART # DESCRIPTION QTY

1 1052140-M GUIDE - SAW SHAFT 1
2 3819120 BUSHING 2

Figure 4 1052140: GUIDE – SAW SHAFT

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 6 of 18

REV E: 04/08

MOTOR ASSEMBLY

MOTOR ASSEMBLY

ITEM PART # DESCRIPTION QTY

1

OPTIONS

2 1051110 ROTOR ASSEMBLY 1
3 1051120 MOTOR SHELL 1
4 1052050 MOTOR BEARING HOUSING 1
5 1052110 PLATE 1
6 1052830 COVER 1
7 3204040 BEARING 1
8 3522060 BEARING 1

9 5002440 RETAINING RING 1
10 5100780 RETAINING RING 1
11 7682140 O-RING 1
12 8048030 SCREW 3
13 8110030 SCREW 3
14 8213060 SCREW 3
15 8313040 SET SCREW 1
16 8507090 WASHER 3
17 8603090 SQUARE KEY 1

STATOR 1

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Figure 5 MOTOR ASSEMBLY

Page 7 of 18

REV E: 04/08

MOTOR ASS'Y 1HP, 550 V, 3 PHASE, 60Hz, 1051250-550-360 2340550 1051110
MOTOR ASS'Y 1HP, 380 V, 3 PHASE, 60Hz, 2.5 AMPS 1051240-380-360 2340540 1051110
MOTOR ASS'Y 1HP, 460 V, 3 PHASE, 60Hz, 2.5 AMPS 1051230-460-360 2340530 1051110
MOTOR ASS'Y 1HP, 230 V, 3 PHASE, 60Hz, 5.0 AMPS 1051230-230-360 2340530 1051110
MOTOR ASS'Y 1HP, 380 V, 3 PHASE, 50Hz, 2.5 AMPS 1051220-380-350 2340520 1051110
MOTOR ASS'Y 1HP, 230 V, 3 PHASE, 50Hz, 5.3 AMPS 1051210-230-350 2340510 1051110

MOTOR ASS'Y 1HP, 115 V, 3 PHASE, 50Hz, 10.6 AMPS 1051210-115-350 2340510 1051110

MOTOR ASS'Y 1HP, 42 V, 3 PHASE, 50Hz, 25 AMPS 1051200 2340500 1051110

DESCRIPTION MOTOR ASS'Y STATOR ROTOR

500E: 1HP MOTOR ASSEMBLY OPTIONS

Figure 6 MOTOR ASSEMBLY OPTIONS

ITEM PART # DESCRIPTION QTY

Figure 7 1051110: ROTOR –SHAFT ASSEMBLY

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

1051110: ROTOR SHAFT ASSEMBLY – 3 PHASE

1 1051100 SHAFT - MOTOR 1
2 2340660 ROTOR – 3 PHASE 1

Page 8 of 18

REV E: 04/08

POWER SUPPLY

1002420: POWER CORD ASSEMBLY, NON 42V

ITEM PART # DESCRIPTION QTY

1 2001240 POWER CORD 1
2 2001270 CABLE CONNECTOR 1
3 2001610 PLUG, MALE 1
4 2001620 SOCKET, FEMALE 1
5 2008220 CORD GRIP 1

Figure 8 1002420: POWER SUPPLY, NON 42V, 3 PHASE

1002430: POWER CORD ASSEMBLY, 42V

ITEM PART # DESCRIPTION QTY

1 2001270 CABLE CONNECTOR 1
2 2001700 GROMMET 1
3 2007030 POWER CORD 1

Figure 9 1002430: POWER SUPPLY, 42V, 3 PHASE

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 9 of 18

WIRING DIAGRAMS

3-PHASE, DIFFERENT CONTROL AND MOTOR VOLTAGE

REV E: 04/08

(IF APPL ICABLE)

NOTES:

1. DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON.

2. ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN.

3. THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE “OFF” POSITION.

4. THE GROUND WIRE (GREEN) OF THE POWER CABLE IS CONNECTED TO THE FRAME OF THE
MACHINE.

To obtain the correct Kentmaster part number for 3-pole contactor and overload
relay, please contact the Kentmaster representative.

Figure 10 WIRING DIAGRAM – different control and motor voltage

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 10 of 18

3-PHASE, SAME CONTROL AND MOTOR VOLTAGE

REV E: 04/08

(IF APPL ICABLE)

NOTES:

1. DO NOT ATTEMPT OR MAKE RAPAIRS ON THE MACHINE WHILE POWER IS ON.

2. ALL ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN.

3. THE ELECTRICAL DIAGRAM SHOWS THE MACHINE IN THE “OFF” POSITION.

4. THE GROUND WIRE (GREEN) OF THE POWER CABLE IS CONNECTED TO THE FRAME OF THE
MACHINE.

To obtain the correct Kentmaster part number for 3-pole contactor and overload
relay, please contact the Kentmaster representative.

Figure 11 WIRING DIAGRAM – same control and motor voltage

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 11 of 18

REV E: 04/08

Figure 12 ELECTRIC MOTOR LEAD HOOKUP DIAGRAM 3 PHASE MOTOR

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 12 of 18

[ENGLISH]

GENERAL INFORMATION

REV E: 04/08

MODEL

“500E” BEEF BRISKET SAW (1050000)

____________________________________________________________________________

SERVICE CENTERS

KENTMASTER LTD. (U.K) KENTMASTER MFG. CO., INC.

16 AVONBANK INDUSTRIAL CENTRE 1801 SOUTH MOUNTAIN AVE.
WEST TOWN ROAD MONROVIA, CALIFORNIA 91016
AVONMOUTH - BRISTOL BS11 9DE UNITED STATES OF AMERICA

UNITED KINGDOM

TELEPHONE: ++ 44- (0) 117- 9235035  TELEPHONE: [phone]

FAX: ++ 44- (0) 117- 9829010 FAX: [phone]

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 13 of 18

You have purchased a powerful tool that, if misused, can cause severe
injury and harm to your employees. You must instruct your employees in
the safe and proper use of this tool and to follow the safety procedures
and instructions that have been supplied by the manufacturer of this tool.
Please follow the following instructions.

1. Instruct tool operators to test the tool each day before using it to be sure it does not malfunction.

Remove and repair any tool that malfunctions.

2. Instruct tool operators to immediately stop using a tool that malfunctions or is defective.

3. Instruct personnel to immediately remove all tools that malfunction. Be sure to disconnect tool from

power supply.

4. Instruct all personnel to stay clear of tool, and not to stand or walk in front of, or next to tool when in
use.

5. Point out to all personnel the dangers related to the misuse of tool and the importance of following
safety procedures and instructions.

6. Do not make, or allow others to make, alterations or modifications to this tool.

Replace all lost or illegible labels.

7. Follow all safety, installation and maintenance instructions provided with this tool. Establish proper
safety procedures in accordance with local and national requirements to prevent accidental energizing
of tool that can cause injuries.

8. If this tool is sold or change in ownership takes place, you must provide the new owner all safety
instructions, notices and maintenance instructions you were originally provided. You can obtain
additional copies of the instructions from Kentmaster, free of charge upon request.

9. Give copies of instructions to: (A) Tool Operators

(B) Maintenance Supervisor
(C) Clean-up Supervisor

NOTICE TO EMPLOYER AND PURCHASER OF TOOL

NOTICE TO SAFETY DIRECTOR

REV E: 04/08

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 14 of 18

REV E: 04/08

GENERAL INFORMATION

__________________________________________________________________________________________

COVERING: SAFETY PRECAUTIONS AND PLACING INTO SERVICE

ELECTRICAL POWERED BEEF SPLITTING SAW

__________________________________________________________________________________________

READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING

THIS TOOL

_____________________________________________________________________________________________________

IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THIS INFORMATION INTO THE HANDS OF THE OPERATOR.

_____________________________________________________________________________________________________

PLACING INTO SERVICE

_____________________________________________________________________________________________________

! WARNING

= Hazards or unsafe practices which could result in severe personal injury, death or

substantial property damage.

! CAUTION

= Hazards or unsafe practices which could result in minor personal injury, product or

property damage.

! NOTICE

= Important installation, operation or maintenance information.

Installation, adjustment repair and maintenance of this tool must be made by trained
and qualified personnel.

Always disconnect power supply from tool before:
(A) Installing or removing blade from tool.
(B) Making repairs or adjustments to the tool.
(C) performing maintenance or cleanup work.

! WARNING

! WARNING

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 15 of 18

DECLARATION DE CONFORMITE -DECLARACION DE CONFORMIDAD- ERKLARUNG BEZUGLICH EINHALTUNG DER VORSCHRIFTEN

MANUFACTURED BY: KENTMASTER MFG CO., INC.

FABRIQUE PAR:

1801 SOUTH MOUNTAIN AVE.

FABRICADA POR:

MONROVIA, CALIFORNIA 91016

HERGESTELLTVON:
FABBRICATO DA:

UNITED STATES OF AMERICA

VERVAARDIGD DOOR:

TELEPHONE [phone] FAX [phone]

TYPE / SERIES: BEEF BRISKET SAW

TYPE / SERIE:
TIPO / SERIE:
TYP / SERIE:
TIPO / SERIE:
TYPE / SERIE:

MODEL: 500E

MODELE:
MODELO:
MODELL:
MODELLO:
MODEL:

SERIAL NO. RANGE: XXXXX
N SERIE: • GAMA DE No. DE SERIE: • SERIEN-NR.-BEREICH: • NUMERI DI SERIE: • SERIENUMMERS:

This product complies with the following European Community Directives:
Ce produit est conforme aux directives de la Communaute europeenne suivantes:

Este producto cumple con las siguientes Directrices de la Comunidad Europea:
Dieses Produkt erfullt die folgenden Vorschriften der Europaischen Gemeinschaft:
Questo prodotto e conforme alle seguenti direttive CEE:
Dit produkt voldoet aan de volgende EG-richtlijnen:

89/392/EEC, 91/368/EEC, 93/44/EEC, 93/68/EEC

_______________________________________________________________________
The following Standards were used to verify compliance with the Directives:

Les normes suivantes ont ete utilisees pour verifier la conformite avec les Directives:
Las siguientes Normas se usaron para verificar el cumplimiento de las Directrices:
Folgende Normen wurden angewandt, um erfullung der vorschriften zu bestatigen:
Per verificare la conformita del prodotto alle direttive sono stati usati i seguenti standard:
De volgende normen zijn gebruikt om naleving van de richtlijnen te bevestigen:

EN 292
_______________________________________________________________________________________________________

RALPH KARUBIAN MONROVIA, CA. U.S.A

Approved by: ________________________ Date: AUG - 1 - 1995

(Engineering Manager) (Directeur technique) (gerente de ingenieria) (verantwortlicher Konstruktionsleiter) (Responsabile tecnico) (ondersteunend technisch mangar)

DECLARATION OF CONFORMITY

DECLARATION OF CONFORMITY

DICHIARAZIONE DI CONFORMITA . CONFORMITEITSVERKLARING

REV E: 04/08

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 16 of 18

REV E: 04/08

Kentmaster Worldwide Location

Kentmaster Equipment (Aust) PTY.LTD.
Unit 2,24 Central Court
Browns Plains Qld. 4118

Australia

Telephone: [phone]
Fax: [phone]
[e-mail]
Kentmaster do Brasil, Ltda.
Av. Dr. Joao Teodoro No. 805
Bairro De Vila Rezende

13405-240 Piracicaba, SP,
Brazil

Telephone #1: (019) 3 413 3113
Telephone #2: [phone]

Fax: [phone]
[e-mail]
Kentmaster (IRL) LTD.
Benamore, Dublin Road.
Roscrea,
CO, Tipperary,
Ireland

Telephone: [phone]
Fax: [phone]
[e-mail]
Kentmaster Equipment (NZ) LTD.
5 Cooper Street

Havelock North
New Zealand

Telephone #1: (64) 6 8777 857
Telephone #2: 0800 KENTMASTER
Fax: [phone]

[e-mail]

Kentmaster South Africa (PTY) LTD.
Johannesburg - S. Africa

Unit 54 Sunnyrock Park
Sunrock Close, Germiston
South Africa

Telephone: [phone]
Fax: [phone]
[e-mail]
Kentmaster (UK ) LTD.
Unit 16 Avonbank Ind. Centre

West Town Rd, Avonmouth-Bristol,
BS11 9DE
England

Telephone: [phone]
Fax: [phone]
[e-mail]
Kentmaster Mfg. Co., Inc.
1801 South Mountain Ave.
Monrovia, CA, 91016
USA

Telephone #1: [phone]
Telephone #2: [phone]
Fax: [phone]
[e-mail]
Kentmaster Omaha
4417 South 139th Street
Omaha, NE, 68137
USA

Telephone #1: [phone]
Telephone #2: [phone]
Fax: [phone]
[e-mail]

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 17 of 18

REV E: 04/08

INDEX

OPERATING AND SAFETY INSTRUCTIONS...................................................................................................................................2

OPERATING INSTRUCTIONS......................................................................................................................................................3

BLADE REMOVAL AND CLEANING..........................................................................................................................................3

SERVICE............................................................................................................................................................................................3

INSTALLATION INSTRUCTIONS ...............................................................................................................................................4

MAINTENANCE...............................................................................................................................................................................4

PARTS BOOK.........................................................................................................................................................................................5

“500E” MAIN ASSEMBLY..............................................................................................................................................................5

MOTOR ASSEMBLY.......................................................................................................................................................................7

POWER SUPPLY..............................................................................................................................................................................9

WIRING DIAGRAMS....................................................................................................................................................................10

3-PHASE, DIFFERENT CONTROL AND MOTOR VOLTAGE ...............................................................................................10

3-PHASE, SAME CONTROL AND MOTOR VOLTAGE..........................................................................................................11

GENERAL INFORMATION...............................................................................................................................................................15

DECLARATION OF CONFORMITY.................................................................................................................................................16

Kentmaster Worldwide Location..........................................................................................................................................................17

INDEX...................................................................................................................................................................................................18

FIGURES - INDEX..............................................................................................................................................................................18

FIGURES - INDEX

Figure 1 MODEL 500E – BLADE REPLACMENT ..............................................................................................................................3

Figure 2 MODEL “500E"........................................................................................................................................................................5

Figure 3 BOM FOR MODEL “500E”.....................................................................................................................................................6

Figure 4 1052140: GUIDE – SAW SHAFT............................................................................................................................................6

Figure 5 MOTOR ASSEMBLY ..............................................................................................................................................................7

Figure 6 MOTOR ASSEMBLY OPTIONS ............................................................................................................................................8

Figure 7 1051110: ROTOR –SHAFT ASSEMBLY ...............................................................................................................................8

Figure 8 1002420: POWER SUPPLY, NON 42V, 3 PHASE.................................................................................................................9

Figure 9 1002430: POWER SUPPLY, 42V, 3 PHASE ..........................................................................................................................9

Figure 10 WIRING DIAGRAM – different control and motor voltage................................................................................................10

Figure 11 WIRING DIAGRAM – same control and motor voltage......................................................................................................11

Figure 12 ELECTRIC MOTOR LEAD HOOKUP DIAGRAM 3 PHASE MOTOR...........................................................................12

KENTMASTER MFG. CO., INC. 1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA 91016 UNITED STATES OF AMERICA

 TELEPHONE: [phone] FAX: [phone]

Page 18 of 18