Kent JINDABYNE, COUNTRY CLASSIC, SOMERSET Owners Manual

Owners Manual
For All

Wood Heaters

COVERS MODELS - JINDABYNE (STD FIRE BOX)

COUNTRY CLASSIC (STD FIRE BOX)
SOMERSET (SLIM LINE FIRE BOX)

Tested and approved to Australian Standards
AS/NZS 2918 and AS/NZS 4013/4012.

Prior to installation check with your state and local
authorities regarding any specific regulations that
may apply.

Please keep these instructions for future
reference.

Burn hardwood only.

2

FIRST THINGS FIRST...

Congratulations on your purchase of a quality Kent wood heater. This product is designed according to strict
environmental, quality and safety standardsand should give you years of trouble freehome heating.

Read these instructions carefully to get the most out of your heater and to ensure safe and satisfactory heater
performance. In particular, we wouldlike to draw your attention to these warnings.

Be careful of what you burn:

*

Use only dry, well seasonedhardwood.

*

Do not use coal orbriquettes.

*

WARNING: DO NOT USE FLAMMABLE
LIQUIDS OR AEROSOLS TO START OR
REKINDLE THE FIRE.

*

Do not burn garbage in the firebox as garbage
can cause a dangerous soot build up and
increase the amount of smoke your heater
produces.

*

Do not burn chemically treated timber as the
poisonous gases given off could damage your
stove.

*

CAUTION: THE USE OF SOME TYPES OF
PRESERVATIVE-TREATED WOOD AS
FUEL CAN BE HAZARDOUS.

*

Do not place any types of builders board eg
fibro, cement sheeting (or any other materials
not specified and tested by the manufacturer)
inside the firebox.

Protect yourself and your family
from burns:

WARNING: OPEN AIR CONTROL BEFORE

*

OPENING FIRING DOOR.

*

The exterior surfaces of the heater will
become hot during operation. For protection
of children, the elderly or infirm, provide a
firescreen to prevent contact with the
appliance in operation.

*

To protect against injury from burns, use
caution when operating the appliance. In
particular, when loading the firebox, provide
adequate protection for your hands.

Use your heater according to these
instructions:

*

CAUTION: THIS APPLIANCE SHOULD BE
MAINTAINED AND OPERATED AT ALL
TIMES IN ACCORDANCE WITH THESE
INSTRUCTIONS.

*

DO NOT BURN WITH DOOR OPEN.

CAUTION: THIS APPLIANCE SHOULD NOT

*

BE OPERATED WITH A CRACKEDGLASS.
Do not throw logs into the firebox. Always

*

place logs carefully.
Load logs with ends pointing to the front of the

*

heater. This will help prevent logs rolling
forward.
Do not overfire (allow firebox to glow red) as

*

this could damage your firebox.
Always leave a minimum of 25mm (1) of ash

*

in the bottom of the firebox. Never empty it
completely.

WARNING: ANY MODIFICATION OF THE

*

APPLIANCE THAT HAS NOT BEE N
APPROVED IN WRITING BY THE TESTING
A U T H O R I T Y I S C O N S I D E R E D A S
BREACHING AS/NZS 4013.

The appliance or flue system should not be

*

modified in any way without the written
approval of the manufacturer.

The heater can get very hot, so
watch obvious fire hazards:

Do not place clothing or other combustible

*

materials on top of theheater.

* WARNING: DO NOT USE FLAMMABLE

LIQUIDS OR AEROSOLS OR PLACE
TH ESE IN TH E VI CIN ITY OF THIS
APPLIANCE WHEN IT IS OPERATING.
WARNING: DO NOT STORE FUEL WITHIN

*

HEATER INSTALLATION CLEARANCES.

Do not store flammable liquids near the

*

heater.
Do not store fuel closeto the stove.

*

Exclusion of Liability

Whilst every care has been taken in formulating these instructions, no responsibility whatsoever will attach to
and/or claim lie against, the manufacturer and/or the distributor of the heater as a result of any failure to follow
the whole or any part of the instructions and/or as a result of incorrect information herein and/or any omission
here from.

ASSEMBLING YOUR NEW HEATER

There are a number of heaters in the Kent range. The heaters are mounted on columns, which require some
assembly. All heaters will require
firebrick and baffle plate assembly.

Convection models are supplied with fans, which will need to be assembled.

3

Column Assembly

There are a few different column styles. Some do
not require screws: you assemble the column by
inserting the tags located at either end of the front
and rear panels. Push the front and rear panels
down to lock tags into position. The column can
be further secured if you wish by fitting self
tapping screws into the holes provided between
the tags (screws not provided).

Other side panels have nuts and screws
provided for you to screwthe panels together.

If your heater comes with a fan, the side panels
will have two holes at the top for securing the fan.
These must face the rearof the firebox.

Next, fit the aluminium heatshield to the top of the
column, ensuring the
shield locates in the
slots at the top of the
column.

You must now attach
the firebox. Lay the
firebox on its back.
Locate the column
onto the four locating
points on the base of
the heater. Ensure the
side of the column with a 45 mm gap on the
bottom edge goes at therear of the heater.

Secure the column to the base of the heater with
the four self tapping screwsprovided.

Now stand the heater and column assembly up
and place into the base.

Deflector & Heat Shield

(For Jindabyne only) Fit the top deflector and
rear heatshield to the rear of the firebox by
pushing the long screws through the holes on the
back firebox panel. Fit
the top deflector first,
then the spacers, rear
heatshield and finally the
n u t s .
Secure
tightly.

Fan Assembly

Fix the fan to the
column using the
f o u r l o c a t i n g
screws provided.

The earth wires on
the fan will need to
be fixed to the
column. Refer to
detail view below.

The fan can be removed
f o r c l e a n i n g b y
unscrewing the locating
screws. Remember to
disconnect the power
supply before touching
the fan.

Firebricks (Standard Firebox)

Standard sized fireboxes use 7 firebricks and a
ceramic base liner in the arrangement shown
below.

Place the base liner down so that it is flush
against the front of the firebox. Place two
firebricks on each side laying down. Place
three firebricks at the back standing upright.

Now place the brick retainer along the back
firebricks so that the lip hangs over the front of
the bricks.

If necessary, push the side bricks towards the
back of the heater so they sit against the brick
retainer. This arrangement prevents the back
bricks from falling forward.

4

ASSEMBLING YOUR NEW HEATER

Firebricks (Slimline Firebox)

Slimline fireboxes use 6 firebricks and a ceramic
base liner in the arrangementshown below.

Place the base liner down so that it is flush
against the front of the firebox. Place two
firebricks on each side standing upright. Place
two firebricks at the backlaying down sideways.

Now place the brick retainer along the back
firebricks so that the lip hangs over the front of
the bricks.

If necessary, push the side bricks towards the
back of the heater so they sit against the brick
retainer. This arrangement prevents the back
bricks from falling forward.

Kick Plate

(For Jindabyne only) To assemble the kick plate,
use the two shortlocating screws provided.

Insert the screws from the inside of the firebox and
then screw the spacer to the front, as shown in the
diagram below. Use the spacers with the threaded
tip.

Now, place the kick plate against the spacers and
secure with the twodome nuts provided.

All Models - Baffle Plate

The baffle plate
MUST be installed
prior to operating the
appliance. Ensure
that the baffle plate is
pointing forward.

The left side of the
pla t e s h o u ld b e
directed over the
plate bracket and pushed against the top left
edge of the firebox. The right hand side should
then be lifted up over the right hand bracket. The
plate can now be allowed to rest into position.
Ensure the plate is sitting evenly on both
brackets, and is pushed all the way to the back of
the heater.