Kenmore PRO V07800-B Use and Care Guide

ange Hood
Use & Care Guide
T(Vl
InstallationManual
Campana de cocina
Manual de uso y cuidado Manual de instalaci6n
Models 233.51003600 (30" wide - Stainless) Modelos 233.51063600 (36"wide - Stainless)
i"n
z
t.=
m
¢0 "r
ITI
Zl
0
r.=
V07800 rev. B Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com
SECTION ....................................................................... PAGE
Warranty .............................................................................. 2
Safety Instructions ............................................................... 2
Operation ............................................................................. 3
Cleaning .............................................................................. 3
Parts Included With Hood ................................................... 4
Parts Not Included With Hood ............................................ 4
Tools Needed ...................................................................... 4
51000 Series Range Hood System ................................... 5
Equivalent Duct Length Chart ............................................ 6
Prepare The Hood Location ............................................... 7
Prepare The Hood ............................................................... 8
Install The Hood .................................................................. 9
Connect The Wiring .......................................................... 10
Wiring Diagram ................................................................. 10
Finalize the Installation ..................................................... 10
Changing Light Bulbs ....................................................... 10
Install The Filters ............................................................... 11
Service Parts ..................................................................... 12
INTENDED FOR DOMESTIC COOKING ONLY ,
WARNING _,
TO REDUCE THE RiSK OF FIRE, ELECTRIC SHOCK, OR iNJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended bythe manufacturer. If you have questions, contact the manufacturer at the
address listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the
service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the
service panel.
3. Installation work and electrical wiring must be done by a
qualified person(s)in accordance with all applicable codes and standards, including fire-rated codes and standards.
4. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent backdrafting. Follow the heating equipment manufacturer's guideline and safety
standards such as those published by the National Fire
Protection Association (NFPA), and the American Society
for Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
5. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Do not use this range hood with any additional solid state
speed control device.
7. Ducted fans must always be vented to the outdoors.
8. To reduce the risk of fire, use only steel ductwork.
9. This unit must be grounded.
TO REDUCE THE RISK OF A RANGETOP GREASE FIRE:
1. Never leave surface units unattended at high settings. Believers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
2. Always turn hood ON when cooking at high heat or when
flambeing food (Cr&pes Suzette, Cherries Jubilee,
Peppercorn Beef Flambe).
3. Clean ventilating fans frequently. Grease should not be
allowed to accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate
for the size of the surface element.
If within 1 year from the date of installation, any part of this range hood fails to function properly due to a defect in
material or workmanship, Sears will repair the part or
furnish and install a new part, free of charge.
FULL 30-DAY WARRANTY ON FINISH ON PAINTED OR BRIGHT METAL PARTS
If within 30 days from the date of installation, the finish on
any painted or bright metal parts of this range hood is defective in material or workmanship, Sears will furnish
and install a new part, free of charge. WARRANTY SERVICE ISAVAILABLE BY CONTACTINGTHE
NEAREST SEARS SEVICE CENTER/DEPARTMENT iN THE
UNITED STATES.
This warranty applies only while this product is in use in the United States. This warranty gives you specific legal
rights and you may have other rights which vary from state
to state. Sears, Roebuck and Co., Dept 817WA, Hoffman Estates,
IL 60179
WARNING ,_, _,
TO REDUCETHE RISK OF INJURYTO PERSONS INTHE EVENT OF ARANGETOP GREASE FIRE, OBSERVETH EFOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO
PREVENT BURNS. Ifthe flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN -You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels
- This could cause a violent steam explosion.
4. Use an extinguisher ONLY if: A You know you have a Class ABC extinguisher and you
already know how to operate it.
B. The fire is small and contained in the area where itstarted. C. The fire department is being called. D. You can fight the fire with your back to an exit.
* Based on "Kitchen Fire Safety Tips" published by NFPA.
CAUTION ,A
1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
2. Toavoid motor bearing damage and noisy and/or unbalanced impellers,keepdrywallspray,construction dust,etc.offpower unit.
3. Your hood motor has a thermal overload which will automatically shut off the motor if it becomes overheated.
The motor will restart when it cools down. If the motor
continues to shut off and restart, have the hood serviced.
4. For best capture of cooking impurities, the bottom of the hood
shouldbe aminimum of24" (30' overa gas range)and a maximum
of 30" (36" over a gas range) above the cooking surface.
5. Toreduce the riskof fire and to properly exhaust air on a ducted installation, be sure to duct air outside - Do not exhaust air into
spaceswithin wallsor ceilingor intoattics,crawlspaces, or garage.
6. This product is equipped with a thermostat which may
start blower automatically. To reduce the risk of injury and to prevent power from being switch on accidentally, switch
power off at service panel and lock or tag service panel.
7. To reduce the risk of fire and electric shock, the Kenmore PRO 51000 Series hood must be installed with blower
models 51200, 51600, or 57745 only. Other blowers
cannot be substituted. (Blowers sold separately).
8. Please read specification label on product for further information and requirements.
AlwaysturnONyourhoodbeforeyoubegincookinginorder toestablishanairflowinthekitchen.Lettheblowerrunfora
fewminutestocleartheairafteryouturnofftherange.This willhelpkeepthewholekitchencleanerandbrighter.
r
I/oELAY o
z/OFF -- 1
_ J
HC0029
1.Delay Off Push Button
2. Blower Speed Push Buttons
3. Halogen Lights Push Button
Delay Off When blower is ON, press on this button (item 1 on picture
above) to start the Delay Off function. The blower will stay at its active power level for 5 minutes and then will shut off
automatically. During the delay function, the active speed LED is blinking slowly to show the delay function is on. To cancel
the delay function, press Delay Off button again; the blower will stay on. Tostop blower and delay function, press on blower
activated speed. Blower Speed
The blower has 3 speed levels. Press once on push button 1 to activate the blower on low
speed, on 2 for medium speed, and on 3 for high speed. When activated, the corresponding blower speed LED is lit.
To stop blower, press once again on the activated blower speed.
NOTE:When blower is off, pressing on blower speed 1 will
cause the blower to start on high speed for a very short lapse of time, and then resume on speed 1.
HEAT SENTRY "rM Your hood is equipped with a HEAT SENTRY TMthermostat.
This thermostat is a device that will turn on or speed up the blower if it senses excessive heat above the cooking surface.
1) if blower is OFF - it turns blower ON to high speed, and LED over speed 3 blinks rapidly. When the temperature level
drops to normal, the blower will return to its original setting (OFF) and LED over speed 3 will shut off.
2) if blower is ON at a lower speed setting - it turns blower up to HIGH speed, and LED over speed 3 blinks rapidly. When the temperature level drops to normal, the blower will still
be running on HIGH speed but the LED over speed 3 stops blinking and stay ON.
Baffle filters The baffle filters should be cleaned frequently. Use a warm
detergent solution. Baffle filters are dishwasher safe. Wash more often if your cooking style generates greater
grease - like frying foods or wok cooking. Remove filters by pushing filters towards the front of hood and
rotating filters downward. Blower Cleaning
Remove the baffle filters in order to access the blower. Vacuum blower to clean. Do not immerse in water. Refer to blower
instruction manual for more details. Hood Cleaning
Stainless steel cleaninq_ How to maintain its"BRIGHT LOOK" Do:
Regularly wash surfaces with clean cloth or rag soaked
with warm water and mild soap or liquid dish detergent.
- Always clean in the direction of original polish lines.
- Always rinse well with clear water (2 or 3times) aftercleaning. Wipe dry completely.
- You may also use a specialized household stainless steel cleaner.
Don't:
Do not use any steel or stainless steel wool or any other
scrapers to remove stubborn dirt.
Do not use any harsh or abrasive cleaners. Do not allow dirt to accumulate.
Do not let plaster dust or any other construction residues reach the hood. During construction/renovation, cover the
hood to make sure no dust sticks to stainless steel surface.
Avoid: when choosing a detergent
- Any cleaners that contains bleach will attack stainless steel.
- Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.
Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc., are highly explosive
and should not be used close to a range.
_ WARNING: The HEAT SENTRY TMthermostat
Halogen Lights Press this push button (item 3 on picture above) to control the
halogen lights. Press once for low intensity, twice for medium intensity and three
times for maximum intensity.Press another time to shut off the lights. NOTE: Light intensity gradually changes between setttings. Use GU10, 50W halogen bulbs. (Included. Please refer to
page 4 for ordering information.) Memory Setting: To memorize a specific light intensity, press
and hold halogen lights button for 2 seconds at the chosen light intensity. Lights will turn off. Next time this push button will
be pressed, lights will turn on at the intensity previously set. NOTE: Any change in light intensity will reset the memory.
can start the blower even if the hood is turned OFF. if you must stop the blower, press and
hold push button 3 for more than 2 seconds.
BaffleFilter (3perhood)
Parts Bag
HRO01 ^&
(includes 4 flat head screws #10-2", 8screws #8-3A', 4 Nuts #10-32,
2 Wall anchors and 2 Washers 3/16'ID x sA"OD)
120V, 50W, MR 16 with GU10 base OR PAR 16 with GU10 base, shiemded halogen lamp
(3 per 30" hood, 4 per 36" hood) Sears Part No. V05921
Ducting Accessories (See "51000 Series Range Hood System" on page 5 for
Ducting Accessory Model Nos.)
Blower (interior OR exterior) (See "51000 Series Range Hood System" on page 5 for
Blower Model Nos.)
/ / Q /
Screwdriver Tape 3/8"
(Robertson or Phillips) Pencil Measure Nutdriver
Drill Saw -or- Saw Duct Tape Stripper
Sabre Keyhole Wire
F
Wall& RoofCaps, Exterior Blower
L
Sears Stock Broan Model Brean Model Humber 57745 437 441
1200 cfm High Capacity 10" Round
Exterior Blower Roof Cap Wall Cap
I I J
Elbows and / _ -_. In-Line Dampers
r
h Broan Model 418 Broan Model 421
10" Round 10" Round Vertical
Adjustable Elbow jln-Line Damper
Ductwork
/
L
Broan Model 410 10" Round Duct
(2 ft. sections)
F
Choose 1of 5 Discharge
Transitions _ l
( i
I
I Broan
Model 427
I
(41/2"x18Y2" 10"Rd.,-vertical) tol0"Rd.,Horiz, tol0"Rd.,Horiz, tol0"Rd.,Horiz. to 10" Rd.,
1_6" high - lateral)
\ L
\
\
Broan Model 423 Broan Model 424 Broan Model 454 Broan Model 453 (4 W' x 18 V2" to (4 W' x 18 V2" (4 W' x 18 V2" (4 V2"x 18 V2"
I front - rear) Horiz. / right) Horiz. / left)
\
\
I I
I
I Optional Flue Extension
I
Sears Stock Humber
I 51012
51024
Broan Model 647 7" Round Wall Cap
Broan Model 407 7" Round Duct
(2 ft. sections)
]
Sears Stock Number 59091 Roof Cap
/
Broan Model 415
7" Round Adjustable Elbow
m
m
m
_b
O
m
m
_rB
m o_ 51036
Sears St Number 58140 __._
Rough-in Kit (Use with Exterior
Blower Model 57745)
Choose 1of 3 Blower Systems
L
SEARS STOCK NUMBERS available through your local
Sears store, on line at Sears.corn, or from Sears Parts
at 1-800-366-7278. For availability of Broan Models,
[ pease ca 1-800-558-1711.
Sears Stock Number 51200 Blower / Rough-in Kit (1200 cfm Interior Blower and
Rough-in Plate)
_eSears Stock
_f- _ Number 51600
_ \ _ Blower/
I _ _ _ / Rough-in Kit I "%_ / \ \o//) ) _ (600 cfm Interior
I _ \ _ Blower and I _ _ Rough-in Plate)
L_ \ / _ 51000 Series Hood
/'_ _ (Canopy with blower
controls & lighting.
Required for all
allations.)
HLO072
Kenmore range hoods are designed to perform efficiently when attached to long runs of duct. As a point of reference, this hood will function at approximately 80% of its rated air performance when 100 equivalent feet of 7" round ductwork is attached (for
600 cfm blowers) or 125 equivalent feet of 10" round duct is attached (for 1200 cfm blowers). Use this chart to calculate the equivalent duct length of your system. Note that 7" round is the minimum recommended duct size for 600 cfm blowers, and 10"
round is the minimum recommended duct size for 1200 cfm blowers.
Broan Model 424
Broan Model 407
Straight Duct
7-in. round x2-ft. long
Equivalent length
41/2-in. x 181/2-in. to
lO-in. Round - Horiz.
Front / Rear Transition
Equivalent length
10 ft.
(_ Broan Model 647
7-in. Round
Wall Cap
Equivalent length
3Oft.
(15-ft. w/o damper)
2ft.
Broan Model 437
Broan Model 410
Straight Duct
10=in. round x 2-ft. long
Equivalent length
2ft.
_) Broan Model 415
7-in. Round Elbow
Equivalent length
Broan Model 454
41/2-in. x 181/2-in. to
lO=in. Round - Horiz.
Right Transition
Equivalent length
12 ft.
Broan Model 453
41/2-in. x 181/2-in. to
lO-in. Round - Horiz.
Left Transition
Equivalent length
12ft.
10-in. Round
Roof Cap
luivalent length
40 ft.
(25-ft. w/o damper)
Broan Model 441
Wall Cap
lO-in. Round
Equivalent length
4O ft.
(25-ft. w/o damper)
8 ft.
10-in. Round Elbow
Broan Model 418
Equivalent length
10 ft.
Broan Model 427
41/2-in. × 181/2-in. to
lO=in. Round, 6-in. High
- Lateral Transition Equivalent length
2ft.
Broan Model 423
41/2-in. x 181/2-in. to
1O-in. Round - Vertical
Transition
Equivalent length
2ft.
Sears
Model 59091
Roof Cap
(7-in. round)
Equivalent length
30 ft. (7-ft. w/o damper)
EARS STOCK NUMBERS available through your Iocai
ears store, on line at Sears.corn, or from Sears Parts at_
1-800-366-7278. For availability of Broan Models,
please call 1-800-558-1711. J
m
1. The Kenmore PRO Series hood must be installed with interior blower models 51200 or 51600, or exterior blower 57745 only. Other blowers cannot be substituted.
(Blowers sold separately.) Plan where and how the ductwork will be located.
Install proper-sized ductwork, transition(s), elbow(s), and roof or wall cap for the model of blower you are using.
For best results, use a minimum number of transition
and elbows.
ROOF CAP
\
, 7"(178 ram)
ROUND DUCT
OPTIONAL FLUE
EXTENSION
or SOFFIT
HOOD
7" (178 ram)
ROUND
ELBOW
f
24" TO 30" (609 1o 762 turn)
ABOVE COOKING SURFACE
HHOO61A
MODEL 51600 SINGLE BLOWER
TYPICAL DUCTWORK
ROOF CAP
OPTIONAL FLUE
EXTENSION
or SOFFIT
\
10" (254 ram)
l WALL CAP
]
2. Dimensions for the most common installations are shown below.
Adjust your measurements for various heights of ceilings, soffits, cabinets or cooktops. For proper operation, the
hood must be a minimum of 24" (30" for a gas range) and a maximum of 30" (36" for a gas range) above the
cooktop.
H * Ai Ceiling
Cabinet,II T T
soffit or . / Top of wood
Hood _,_
t
Minimum distance between
the hood and an electric
cooktop: 24" (610 mm)
Maximum distance between
the hood and an electric
cooktop: 30" (762 mm)
q_l_
HHOO64A highcooktop I
Standard 36" (914 mm)l
MINIMUM AND MAXIMUM DISTANCE i
BETWEEN COOKTOP ELECTRIC RANGE
m
m
m
m
O
m
m
HOOD
t
24" TO 30" (609 1o 762 rara)
ABOVE COOKING SURFACE
}4F]0062A
to 10"
(114 x 470 to
254 rnra) ROUND
TRANSITION
(see page 5)
MODEL 51200 DUAL BLOWER |
TYPICAL DUCTWORK
EXTERIOR BLOWER
10" (254 rnra)
ND DUCT
OPTIONAL FLUE
or SOFFIT ROUND ELBOW
HOOD
S _58140
,_ (see page 5)
24" TO 30" (609 1o 762 ram)
ABOVE COOKING SURFACE
HHOO63A
/
(254 ram)
>EXTERIOR
BLOWER
ROUGH-IN KIT
MODEL 57745 EXTERIOR BLOWER |
TYPICAL DUCTWORK
1
!
1
I . A Am Ceiling
Icabinet'II ]" T
soffit or II A / Top of wood
ecora,,4, /mo°nt,ngstdp
, f,ue 1A+f"(2 mm)
% V
Hood \\_
t
Minimum distance between
the hood and a gas
cooktop: 30" (762 ram)
Maximumdistance between
the hood and a gas
cooktop: 36" (914 ram)
HHOO65A high cooktop |
{ M,NIMUMANDMAXIMUMDISTANCEi
BETWEEN COOKTOP
2
1. Measure and mark a level line on wall above cooktop location for the wood mounting strip (see illustration
to the right and under step 2 on page 7). Unscrew the mounting strip from the hood and discard the screws.
Use #10=2" fiat head screws (included in the parts bag) to secure the mounting strip to the drywall. Make sure to hit
the wall studs.
CAUTION: Due to the weight of this hood, ensure that the wood strip is attached to all of
the available wall studs (2 studs minimum for the 30" hood, more for a 36" hood); not into
drywall alone.
2. Remove filters from hood and set aside.
from
Page7)
11/2"
138ram)
1. Drywall HD0169A
2. Wood Mounting Strip
3. Flat Head Screw
4. Wall Anchor Location
5. Outline of the Back of the Hood
6. Wall Studs
3. Using a Phillips #2 or a Robertson #2 screwdriver, remove 4 screws retaining the pan to the hood (shaded part on
illustration beside) and set aside.
HD0172
HD0170
Loading...
+ 16 hidden pages