Kenmore Pro 79031023700, 79031023701 Installation Guide

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY

A QUALiFiED iNSTALLER.

iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.

READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.

If the information in this manual is not followed exactly, a fire or explosion may result causing

property damage, personal injury or death.
FOR YOUR SAFETY:

-- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.

-- WHAT TO DO IF YOU SMELL GAS:

° Do not try to light any appliance.
° Do not touch any electrical switch; do not use any phone in your building.
° Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

° If you cannot reach your gas supplier, call the fire department.

-- Installation and service must be performed by a qualified installer, service agency or the gas supplier.

For Standard
Installation:

Gas Cooktop Dimensions

GasCooktop Cutout
Dimensions 3"(7.6cm)

2"(5.1 cm) Dia.

Opening to route

power cable

F

G

Do not slide unit into cabinet cutout.
Protruding screws on the bottom of ur it

may damage the bottom front finish.

C

4"X 4" (10.2 cmx I0.2 cm)

i to route gas supply.

**Note: D & Eare critical to the proper
installation of the cooktop. D reflects the

finished dimension. Due to the variation in
countertop materials, it isrecommended to first

undercut this dimension, and then adjust it

Figure 1

upon installation of the cooktop.

* 30" (76.2 cm) rain. for

unprotected cabinet and
24" (61 cm) rain. for cabinet
with protected bottom surface.

71/4

(18.4 cm)

30 (76.2) 297/8(75.9) 25 (63.5) 73A(19.7) 29_5/16 (76) I 293/16(74.1)

All dimensions are stated in inches and (cm).
NOTE: Wiring diagrams for this cooktop are enclosed in this booklet

22 (55.9) 1% (2.9) Max 7V2 (19.1)

318201473 (0708) Rev. C

English - pages 1-8

Espahol - p_iginas 9-16

Wiring Diagram page - 8

For Installation with the optional Stainless Steel Backsplash.

GasCooktop Dimensions

2" (5. I cm)

9"(22.9cm)
Optional

Stainless Steel

Backsplash

* 30" (76.2 cm) min. for

unprotected cabinet and
24" (61 cm) min. for cabinet
with protected bottom surface.

C

***Note: Applies only in case
of countertop backwall.

2"(5.1 cm) Dia.--

opening to route

power cable.

GasCooktop Cutout Dimensic%

Do not slide unit into cabinet cutout.

Protruding screws on the bottom of unit
may damage the bottom front finish.

Figure 2

4"X 4" (10.2 cm x 10.2 cm)

pening to route gas supply.

H

7Y4"(18.4 cm)

29V8

cm)

**Note: D & E are critical to the proper
installation of the cooktop. D reflectsthe

finished dimension. Due to the variation in
countertop materials, it isrecommended to first

undercut this dimension, and then adjust it
upon installation of the cooktop.

30 (76.2) 297/8(75.9) 25 (63.5) 73A(19.7) 29_s/_(76) 293/_6(74.1) 22(55.9) 1Y8(2.9) Max. 7Y2(19.1) 29_s/_6(76)

All dimensions are stated in inches and (cm).

Important Notes to the Installer

1. Read all instructions contained in these installation
instructions before installing the cooktop.

2. Remove all packing material before connecting the
electrical supply to the cooktop.

3. Observe all governing codes and ordinances.

4. Be sure to leavethese instructions with the consumer.

5. Note: For operation at 2000 ft. elevations above see
level, appliance rating shall be reduced by 4 percent

for each additional 1000 ft.

Important Note to the Consumer

Keep these instructions with your Use and Care Guide for

future reference.

Depth Adjustment Filler Kit #903051-9100

This cooktop isdesigned to replace existing unit. If the
depth of your countertop opening isbigger than 7Y4" (18.4
cm) and lessthan 8Y2" (21.6 cm) you can order a free filler

kit #903051-9100 by calling SearsParts & Repair Center at
1-800-4-MY-HOME®.

Optional Item Available:

• A 9" (22.9cm) Stainless Steel Backsplash

Kit #903048-9100
This kit can be ordered for purchase through SearsParts

& Repair Center at 1-800-4-MY-HOME®.

IMPORTANT SAFETY

• Be sure your cooktop is installed and grounded
properly by a qualified installer or service

technician.
This cooktop must be electrically grounded in

accordance with local codes or, in their absence,
with the National Electrical Code ANSI/NFPA No.

70--latest edition in the United States, or in
Canada, with the Canadian Electrical Code, CSA

C22.1 Part 1.

• The burners can be lit manually during an

electrical power outage. To light a burner, hold a

lit match to the burner head, then slowly turn the
Surface Control knob to LITE. Use caution when

lighting burners manually.

• Do not store items of interest to children in

cabinets above the cooktop. Children could be

seriously burned climbing on the cooktop to reach
items.

• To eliminate the need to reach over the surface
burners, cabinet storage space above the burners

should be avoided.

• Adjust surface burner flame size so it does not

extend beyond the edge of the cooking utensil.

Excessive flame is hazardous.

• Never use your cooktop for warming or heating

the room. Prolonged use of the cooktop without

adequate ventilation can be hazardous.

• Do not store or use gasoline or other flammable

vapors and liquids near this or any other
appliance. Explosions or fires could result.

INSTRUCTIONS

Installation of this cooktop must conform with local codes
or, in the absence of local codes, with the National Fuel
Gas Code ANSI Z223.1/NFPA54--1atest edition in the

United States, or in Canada, with the Canadian Fuel Gas
Code, CAN/CGA B149 and CAN/CGA B149.2.

When installed in a manufactured (mobile) home
installation must conform with the Manufactured Home

Construction and Safety Standard, title 24 CFR,part
3280 [Formerly the Federal Standard for Mobile Home
Construction and Safety, title 24, HUD (part 280)] or,
when such standard is not applicable, the Standard for

Manufactured Home Installation, ANSI/NCSBCS A225. I
or with local codes where applicable.

This cooktop has been design certified by CSA

International. As with any appliance using gas and
generating heat, there are certain safety precautions you

should follow. You will find them in the Use and Care
Guide, read it carefully.

The electrical power to the cooktop

must be shut off while gas line connections are
being made. Failure to do so could result in serious
injury or death.

13"(33cm)max.depth ,

forcabinetinstalledabove
cooktop

30"(76.2cm)Min.
ClearanceBetweenthe

TopoftheCooking
PlatformandtheBottom

ofanUnprotectedWood
orMetalCabinet

24"(61cm)Min.
whenBottomofWoodjlf

orMetalCabinetis
ProtectedbyNotLess

ThanI/8" Flame
RetardantMillboard

Covered With Not Less
Than No. 28 MGS

Sheet Steel, 0.015"
(0.4 mm) Stainless
Steel, 0.024" (0.6 mm)

Aluminum or 0.020"
(0.5 mm) Copper

"_-. _min

"l_ between rear edge of

18" (45.7 cm) P

Min.

cutout and nearest
combustible surface

30" (76.2 cm) min.
clearance between

the top of the
cooking platform and

the bottom of an

unprotected wood or
metal cabinet.

_To eliminate the risk of
burns or fire from reaching over heated

surfaces, cabinet storage space located
above the cooktop should be avoided. If

cabinet storage is provided, risk can be
reduced by installing a range hood that

projects horizontally a minimum of 7"
(17.8 cm) beyond the bottom of the

cabinets.

It isnot recommended to use

drawer underneath cooktop.

30" (76.2cm) 30" (76.2cm) 5" (12.7 cm) 5" (12.7 cm)

Figure 3 - CABINET DESIGN

Wall Outlet Location

(10_'cm)/-_

:

I 5"

, (12.7 cm)

Recommended , |

area for 120V I |
grounded outlet _, / ,,

on rear wall. _ (40.6 cm)

CENTRE

NOTE: If an LINE

outlet is not OFUNIT
available, have I

one installed by a ,
qualified I

technic_

Figure 4'- OFUNIT

Provide an Adequate Gas Supply

This cooktop is designed to operate on natural gas at 4"
(10.2 cm) of manifold pressure only.
A pressure regulator is connected in series with the

manifold on the cooktop and must remain in series with
the supply line.

For proper operation, the maximum inlet pressure to
the regulator must be no more than 14" (35.6 cm) of

water column (W.C.) pressure.

For checking the regulator, the inlet pressure must be at

least 1"(2.5 cm) (or 2.5 kPa) greater than the regulator

manifold pressure setting. The regulator isset for 4"
(10.2 cm) of manifold pressure, the inlet pressure must

be at least 5" (12.7 cm).
The gas supply line to the appliance should be 1/2" (1.3

cm) or 3/4" (1.9 cm) pipe.

LP/Propane Gas Conversion

This appliance can be used with Natural gas or LP/

Propane gas. It is shipped from the factory for use with

natural gas.
A kit for converting to LPgas is supplied with your
cooktop. The kit is marked "FOR LP/PROPANEGAS

CONVERSION".
The conversion must be performed by a qualified service

technician in accordance with the kit instructions and all

local codes and requirements. Failure to follow

instructions could result in serious injury or property
damage. The qualified agency performing this work
assumes responsibility for the conversion.

16

.. _, CENTRE

LINE

Failure to make the appropriate

conversion can result in serious personal injury and
property damage.

Important: Remove all packing material and

literature from cooktop before connecting gas and
electrical supply to cooktop.

Install Pressure Regulator

Install the pressure regulator with the arrow on the
regulator pointing up toward the unit in a position where
you can reach the access cap.

Do not make the connection too tight.
The regulator is die cast. Overtightening may crack the
regulator resulting in a gas leak and possible fire or

explosion.

Manual GAS FLOW Pressure
Shutoff Flare _'_ Flare Regulator

Valve Union Union _,

Nipple Flexible Nippl

Off Connector

All connections must be wrench-tightened

Figure 5

Assemble the flexible connector from the gas supply pipe
to the pressure regulator in the following order:

I. manual shutoff valve

2. I/2" (1.3 cm) nipple

3. 1/2" (1.3 cm) flare union adapter

4. flexible connector

5. I/2" (1.3 cm) flare union adapter

6. 1/2" (1.3 cm) nipple

7. pressure regulator
Use pipe-joint compound made for use with Natural and

LP/Propane gas to seal all gas connections. If flexible

connectors are used, be certain connectors are not

kinked.
The supply line should be equipped with an approved

shutoff valve. This valve should be located in the same
room as the cooktop and should be in a location that

allows ease of t_
opening and

closing. Do not %%
block access to

the shutoff valve.
The valve is for

turning on or
shutting off gas
to the appliance.

Shutoff Valve

Open position

Access

Cap