Kenmore Elite 79049212800, 79049213800, 79049219800 Installation Guide

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER.

iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.

READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.

FORYOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the

vicinity of this or any other appliance.

GENERAL INFORMATION

The Warm & Serve Drawer can be used:

• As a stand alone appliance As a combination 27" or 30" Warm & Serve Drawer with a 27" or 30" (76 cm) built-in oven mounted above

IMPORTANT: The warmer drawer must be installed on a surface that is leveled from left to right, rear to front, and is

capable of supporting 100 Ibs (45 Kg).

Warm & Serve Drawer Dimensions

NOTE: A 60" (152 cm) long cable is supplied with the

Warm & Serve Drawer.

Stand Alone Installation

60" (152 cm) Cord

IMPORTANT: The Warm & Serve Drawer runs off a single phase three-wire 120 volt, 60 hertz, AC only

electrical supply with ground.

Combination Warm & Serve Drawer/

27" or 30" (76 cm) Built-in Oven Installation

CAUTION: Install two 3" (7.6 cm) wide x 3.4" (1.9 cm) thick planks

capable of supporting 200 Ibs (90.7 Kg)

& Serve Drawer

271'Models 11¼"(28.6cm) 27"(68.6cm) 233/8"(59.4cm) 30"Models 11¼"(28.6cm) 30"(76.2cm) 233/8"(59.4cm)

(74_

H* = 11-7/8" (30,2 cm) Min. is the space between the bottom ofthe warmer drawer cutout and the bottom of the

oven cutout. This is a critical dimension and must be provided. J** = 3" (7.6 cm) Max. Electrical Junction Box for wall oven must be

lower than warmer drawer cutout.

27"Models 11¼"(28.6cm) 27"(68.6cm) 233/8"(59.4cm)

30"Models 11¼"(28.6cm) 30"(76.2cm) 233/8"(59.4cm)

27"Models- Min. 97/8"(25.1cm) 25½"(64.8cm) 235/8"(60cm)

Max. 10_A"(26cm) 253A"(65.4cm) 241'(61cm)

30"Models- Min. 97/8"(25.1cm) 28Y2"(72.4cm) 235/8"(60cm)

Max. 10_A"(26cm) 283A"(73cm) 24"(61cm)

Printed in the USA

27"-Min. 97/8"(25.1cm) 25Y2"(64.8cm) 235/8"(60cm) 2I'(5.1cm)

Max. 10¼1.(26cm) 25;A"(65.4cm) 24"(81cm) Do,endsons_itinnl

dimensionH

30"-Min. 97/8"(25.1cm) 28_"(72.4cm) 235/8"(60cm) 2I'(5.1cm)

Max. 10¼"(26cm) 283A"(73cm) 24"(61cm) Dn_ends0ns,itinnl

dimensionH

P/N318201813 (0805)Rev.A

English - pages 1-2; EspaAol - p_fginas3-4

Fran_ais - pages 5-6; Notes - pages 7-8

important Notes to the installer

1. Read all instructions contained in these installation instructions before installing appliance.

2. Remove all packing material from appliance before connecting the electrical supply.

3. Observe all governing codes and ordinances.

4. Besure to leave these instructions with the consumer.

important Note to the Consumer

Keep these instructions for future reference.

IMPORTANT SAFETY

INSTRUCTIONS

* Be sure your appliance is installed and plugged

into a 120 Volt grounded outlet.

* This appliance must be electrically grounded in

accordance with the National Electrical Code ANSI/ NFPA No. 70--latest edition in the United States,

or CSA C22.1, Part I in Canada, and local code requirements.

TooJs You Will Need

Phillips@ Screwdriver Pencil

Ruler or Tape Measure and Straight-edge Hand Saw or Saber Saw

Spirit Level Warm & Serve Drawer Installation

1.Locate the 2 anti-tip brackets supplied asshown in fig. 1.

z Zf

Use screws _, supplied to attach

drawer to front of

Figure 2

cabinet. ModeJ and Serial Number Location

The serial plate is located as shown below. When ordering parts for or making inquiries about your

Warm & Serve Drawer, always be sure to include the

model and serial numbers and a lot number or letter

from the serial plate.

>k" "

j._" jJ

......24" (64.3 cm) Max.

..-_. %" (60 cm) Min.

(32.15 cm).......... '--_ Figure 1

2.Slide drawer into cutout opening until front frame of

drawer is flush against cabinet. Be careful not to pinch electrical cord.

3.Remove the drawer as instructed in the Use & Care

Guide and secure drawer housing to cabinet using the 3 nickel-plated screws supplied (see Figure 2). Do not overtighten screws.

4.The 60" (152 cm) appliance power cord can now be

connected into the 120 Volt outlet.

5.Proceed with mounting built-in oven above the drawer (if applicable). Follow installation instructions provided with built-in oven. Make sure to use anti-tip brackets supplied with the built-in oven.

Serial Plate Location

Combination Warm & Serve Drawer

and Cooktop installation

_-</::-- _

Warmer

Drawer

Cutout

You can install the warmer drawer in combination with

an electric or gas cooktop. You must follow the specifications from the installation instructions of the cooktop to avoid interference with the gas or electric

installation.

LA INSTALACION Y ELSERVICIO DEBEN SEREJECUTADOS POR UN INSTALADOR CALIFICADO. IMPORTANTE:

GUARDE ESTAS INSTRUCCIONES PARA EL USO DELiNSPECTORLOCAL DE ELECTRICIDAD.LEAY GUARDE

ESTASINSTRUCCIONES PARA FUTURAS REFERENCIAS.

PARA SU SEGURIDAD: No almacene o use gasolina u otros vapores y liquidos combustibles

cerca a _ste o a cualquier otro electrodom_stico. INFORMAClON GENERAL

Elcajon calentador puede set usado:

• Como unidad independiente

• Enuna combinacion entre el cajon calentador yel homo de30 (76 cm) pulgadasintegrado y montado por encima del cajon

IMPORTANTE: El cajon calentador debe de estar instalado con una surperficie liana, de la izquierda a la dececha, de la parte de atr_is al frente. La superficie debe poder sostener 1OOlibras (45 Kg).

Dimensiones del cajon calentador

NOTA: Un cable de 60" (152 cm) de largo es suministrado con el cajon calentador.

Instalaci6n de la unidad independiente

C " Cable de 60"

J (152 cm)

IMPORTANTE: El cajon calentador funciona con un

suministro de energ[a electrica de corriente alterna, de tres cables, de una sola fase, de 120 voltios, 60 hertz con

I[nea a tierra.

Instalaci6n de la combinaci6n cajon

calentador y homo de 30" (76 cm) integrado

Precauci6n: Dostablas de 3"(7.6 cm) por 3/4" (1.9 cm) necesitan ser instaladasy deber_qnsoportar

200 libras(90.7 Kg)

S _',"-.. _/- calentador

Distanda Minima del pige. _,_ _ 4 1/2 (11.4 cml_ f "- -'J_ . _ "-...

M0del0s27" 11_A"(28.6cm) 27"(68.6cm) 233/8"(59.4cm) M0del0s30" 11¼"(28.6ore) 30"(76.2ore) 233/8"(59.4ore)

M0del0s2T" Min. 97/8"(25.1cm) 25½"(64.8crn) 235/8"(60crn)

M_x. 10¼"(26cm) 253A"(65.4cm) 24"(61cm)

M0del0s30" Min. 97/8"(25.1cm) 28_"(72.4cm) 235/8"(60crn)

M_x. 10¼"(26cm) 28_A"(73cm) 24"(61cm)

29 1/16"

(74,9 cm)

H* = 11-7/8" (30.2 cm) Min. es una dimensi6n critica y necesita set respetada.

J**= 3" (7.6 cm) Max. La Caja para las conexiones electricas para el

homo de empotre p_ede estar de bajo de la abertura del cajon calentador.

M0del0s27" 11¼"(28.6cm) 27"(68.6cm) 233/8"(59.4cm) M0del0s30" 11¼"(28.6cm) 30"(76.2cm) 233/8"(59.4cm)

27"-Min. 97/8"(25.1cm) 25½"(64.8cm)235/8"(60cm)2"(5.1cm)

M_x. 10_A"(26cm) 253A"(65.4ore) 24"(61crn) _°_na°a°_

_imensi6ncritical{

30"-Min. 97/8"(25.1cm) 28½"(72.4cm) 235/8"(60cm) 2"(5.1cm)

MAx. 10¼"(26cm) 283A"(73cm) 24"(61crn) _0,_na0a0_,

_imensi6ncritical{

Impreso en los EUA

P/N 318201813 (0804) Rev.A

English - pages 1-2; EspaSol - p_iginas 3-4

Fran_ais - pages 5-6; Notes - Pages 7-8

+ 5 hidden pages