Kenmore Elite 79049203403, 79049202403, 79049183800, 79049273700, 79049209403 Installation Guide
iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER.
iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.
READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.
FORYOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
GENERAL iNFORMATiON
The Warmer Drawer can be used: As a stand alone appliance or as a cornbination Warmer Drawer with a built-in oven
mounted above
IMPORTANT: The warmer drawer must be installed on a surface leveled from left to right, rear to front and the surface
must be capable of supporting 100 pounds (45 Kg).
Warmer Drawer Dimensions
NOTE: A 60" (152 cm) long cable is supplied with the
Warmer Drawer.
Stand Alone Installation
iMPORTANT: The Warmer Drawer runs off a single
phase three-wire 120 volt, 60 hertz, AC only electrical
supply with ground.
Combination Warmer Drawer/
30" (76 cm) Built-in Oven Installation
Caution: Two 3" (7,6 cm) wide X 3/
4" (1,9 cm) thick planks have to be
installed and they should be able to
support 200 pounds. (90,7 Kg)
27"Models
30"Models
10"(25,4cm) 27"(68,6 cm) 23 3/8" (59.4cm)
10"(25,4cm) 30"(76,2 cm) 23 3/8" (59.4cm)
i!i!i!i!i!i!i!i!i!i!!i!ii!i!i_!iiiiiii_ii:i_!__i_i!_ii_i_!i_!i_!i_!i_!i_!_!i_!_i!_jiiiiii!i!i!ii!iiii_ii_i_i_i_ii_ii_iiiiilililililiiiill¸¸¸¸¸
27"Models-Min.
30"Models-Min.
* Note: It is also possible to install this warmer drawer in a
height opening of 9_A" (23.5 cm). Pleaserefer to page 3
for complete instructions.
PrintedinUnitedStates
83/8"(21,3cm)
Max.
85/8"(21,9cm)*
83/8"(21,3cm)
Max.
85/8"(21,9cm)*
251/2"(64,8cm) 235/8"(60cm)
253/4"(65,4cm) 24"(61cm)
281/2"(72,4cm) 235/8"(60cm)
283/4"(73cm) 24"(61cm)
B J
" lJ c
H* =10-1/8" (25.7 cm) Min. is a Critical
dimension and must he applied.
J** = 3" (7.6cm) Max. Electrical Junction Box for wall oven can he
lower than warmer drawer cutout or higher than walloven cutout.
27" Models 10" (25,4cm) 271'(68,6 cm) 23 3/8" (59.4cm)
30" Models 10" (25,4cm) 30"(76,2 cm) 23 3/8" (59.4cm)
28½" (72,4cm) 23 5/8"(60 cm)1_"(3.8
85/8"(21,9cm) 283A'' (73 cm) 24"(61cm) di,,e,si0,H
P/N 318201807 (0606) Rev.
English - pages 1-4
Espa_ol- paginas 5-8
Fran_ais - pages 9-12
Important Notes to the Installer
I. Read all the instructions contained in these installation
instructions before installing appliance.
2. Remove all packing material from the appliance before
connecting the electrical supply.
3. Observe all governing codesand ordinances.
4. Be sure to leave these instructions with the consumer.
Important Note to the Consumer
Keep these instructions for future reference.
IMPORTANT SAFETY
INSTRUCTIONS
• Be sure your appliance is installed and plugged
into a 120 Volt grounded outlet.
• This appliance must be electrically grounded in
accordance with the National Electrical Code ANSI/
NFPA No, 70--latest edition in the United States,
or CSA C22,1, Part 1 in Canada, and local code
requirements.
Tools You Will Need
Phillips@ Screwdriver
Pencil
Ruler or Tape Measure and Straight-edge
Hand Saw or Saber Saw
Level
I. Locate the 2 anti-tip brackets supplied as shown on
figure I. Fix them using 2 of the 4 black head
screws (10-16 X lY4") supplied.
2. Slide the drawer into the cutout opening until the
front frame of the drawer is flush against the
cabinet. Be careful not to pinch the electrical cord.
3. Remove the drawer as instructed in the Use & Care
Guide and secure the drawer housing to the cabinet
using the 2 black head screws (10-16 X 3A") supplied
(see Figure 2). Do not overtighten screws,
4. The 60" (152 cm) appliance power cord can now be
connected into the 120 Volt outlet.
5. Proceed with mounting the built-in oven above the
drawer (if applicable). Follow the installation
instructions provided with the built-in oven. Make
sure to use the anti-tip brackets supplied with the
built-in oven.
/
/
/
/
/
/
i
i
i
.....-
Warmer Drawer Installation
A, Standard installation (see cutout dimensions on
page 1).
/ .- /
/
Center",,'" ..............
Line _ .........
.-i_._ _ ....l..... / 24" (64.3 cm) Max.
" A.._ .._ 23 %" (80cm)Min.
27" Models 10 31/32"(27,9 cm) 21 15/16"(55,7 cm)
30" Models 12 21/32"(32,2 cm) 25 5/16"(64,3cm)
X
f"
Use the black head screws
supplied to attach the drawer
to the front of the cabinet.
Figure 2
Figure 1
B.Installationfora cutoutheightof 91/4(23.5cm)
(for30"WarmerDraweronly):
1. Locatethe 2 anti-tip bracketsandthe 2 front
supportssuppliedasshownonfigure3. Fixthem
usingthe 4 black headscrews(10-16 X lY4")
supplied
2. Installthe4spacers(Figure4)suppliedunderdrawer
asshowninfigure5 usingthe4screws(10-24X%").
Installtwospacersoneachsideof drawer.
3. Slidethe drawerintothe cutoutopeninguntilthe
front frame of the drawer is flush againstthe
cabinet.Becarefulnottopinchtheelectricalcord.
4. Removethedrawerasinstructedinthe Use& Care
Guide and secure the drawer housing to the cabinet
using the 2 black head screws (8-18 X Y2") supplied
(see Figure 2). Do not overtighten screws.
5. The 60" (152 cm) appliance power cord can now be
connected into the 120 Volt outlet.
6. Proceed with mounting the built-in oven above the
drawer (if applicable). Follow the installation
instructions provided with the built-in oven. Make
sure to use the anti-tip brackets supplied with the
built-in oven.
S SPACER
SCREW
Figure 4
Front Su
7"
Anti-tip Bracket
i
Use the screws supplied to fix
the drawer support
Figure 5
Figure 3
NOTES
Loading...