Kenmore Elite 79048893110, 79048893111, 79048893112, 79048883112, 79048883111 Installation Guide

Convection Microwave Oven Installation Instructions

Installation and service must be performed by a qualified installer.

IMPORTANT: Save for local electrical inspector's use.

Read and Save these instructions for future reference.

The electrical requirements for this oven are 120 volts, 15 amps.

NOTE

1. Base must be capable of supporting 150 pounds (68.0 kg)
for the Convection Microwave Oven only.

2. Make sure base is level and front of cabinet is square. If
the cabinet base is not level, the oven will tend to slide out
when opening the door.

3. Minimum required distance is 36" (91.44 cm) from the
floor.

4. The outlet should not be located in the shaded area of

Figure 1. It is required the outlet be a dedicated 120 volts

with a 15amp rating for the appliance.

5. Minimum required distance between the Microwave Oven
and the wail oven cutouts should be at least 3 inches. The

actual visible space will be reduced due to the overlap of
the Microwave Oven lower vent and the wail oven.

Figure 1

Product Dimensions

Model A B C D

27" (68.8) 27" (68.8) 213¼" (55.3) 247/8" (63.2) 203¼" (52.6)
30" (76.4) 30" (76.4) 213¼'' (55.3) 28" (71.1) 203¼" (52.6)

Cutout dimensions and cabinet width

Model Min. F Max. G Min. H Max. [

27" (68.8) 251/8'' (63.8) 255/8'' (65.1) 24" (61.0) min. 21" (53) 211/2" (54.6) 27" (68.8) min.
30" (76.4) 281/2 '' (72.4) 29" (73.7) 24" (61.0) min. 21" (53) 211/2'' (54.6) 301/8 '' (76.5) min.

All dimensions are in inches (cm).

P/N 316902472

TINSEB527MRRO

1 E

Convection Microwave Oven Installation instructions

IMPORTANT NOTES TO THE INSTALLER

Read all instructions contained in these installation
instructions before installing the Convection Microwave

Oven. This oven can be built into a cabinet or wail
by itself or above any electric wail oven or warming

drawer.

.

Remove aii packing material from inside the oven
cavity before connecting the electrical supply to the

Convection Microwave Oven. DO NOT REMOVE THE
WAVEGUIDE COVER, which is located on the cavity

ceiling. See Figure 2A.

Waveguide Cover_

Oven Cavity

Door Seals

and Sealing

Surfaces

Hinge

Safety

Door Latch ,_

iMPORTANT SAFETY

iNSTRUCTiONS

Never use your appliance for warming or heating the room.
Prolonged use of the oven without adequate ventilation can
be dangerous.

CARPENTRY

Refer to Figure 1for the dimensions required for your
appliance, and the space necessary to install the oven. The
oven support surface should be solid plywood or similar

material, the surface must be level from side to side and
from front to rear.

ELECTRICAL REQUIREMENTS

The appliance operates on a 120 volt, 60 Hz electrical

supply with a separate ground wire. Provide a separate
circuit with a fuse or circuit breaker rated for 15 amps.

Figure 2A Figure 2B

3. Remove the 2 shipping duct supports (see Figure 2B) by
removing the 2 screws securing each side. Reinsert 2
screws (each side) to secure the stainless cover.

4. Remove the feature sticker, if there is one, from the
outside of the door.

.

Check the oven for any damage, such as misaligned or
bent door, damaged door seals and seaiiing surfaces,
broken or loose door hinges and latches and dent inside
the cavity or on the door.

If there is any damage, do not operate the oven and
contact your dealer or KENMORE AUTHORIZED SERVICER.

6. Observe all governing codes and local ordinances.

7. Be sure to leave these instructions with the consumer.

IMPORTANT NOTE TO THE CONSUMER
Keep these instructions with your Owner's Guide for future

reference.

Observe all governing codes and local ordinances

To prevent damage to the oven control, during cold
temperature weather, wait at least three (3) hours
after receiving this oven before supplying power to the
appliance. This will prevent possible damage to the built-in
oven control at power on.

CABINET INSTALLATION

The Convection Microwave Oven can tip when the door is
open. The Anti-Tip brackets supplied with the Convection

Microwave Oven must be attached to the cabinet and
the appliance to prevent tipping of the unit and injury to

persons.

ANTI-TIP BRACKETS INSTALLATION INSTRUCTIONS

1. Unpack the Convection Microwave Oven and find the
2 Anti-Tip brackets and screws included in the literature
package.

E 2

2. Install the Anti-Tip bracket in the cabinet as shown

on Figure 3. Note: To prevent damage to cabinet, it is

recommended to drill 1,_6"(0.16 cm) diameter pilot holes
before installing the Anti-Tip brackets.