Kenmore Elite 66544099502, 66544094502, 66544099500, 66544099501, 66544094500 Installation Guide
...
L 1 T
®
ELECTRIC COOKTOP INSTALLATION INSTRUCTIONS
INSTRUCCIONES DE INSTALACION DE LA SUPERFICIE
DE COCCION ELI_CTRICA
INSTRUCTIONS D'INSTALLATION DE LA
TABLE DE CUISSON I_LECTRIQUE
Table of Contents / |ndice / Table des mati_res
COOKTOP SAFETY .......................................... 2
INSTALLATION INSTRUCTIONS .................... 2
Tools and Parte .............................................. 2
Location Requirements ................................. 2
Eleetrioal Requirements ................................ 3
Prepare Cooktop for Installation ................... 4
Install Cooktop ............................................... 4
Make Electrical Connection ........................... 5
Attach Cooktop to Countertop ...................... 6
Complete Installation ..................................... 6
SERVICE NUMBERS ................. BACK COVER
SEGURIDAD DE LA SUPERFICIE DE
COCCION .......................................................... 8
INSTRUCCIONES DE INSTALACI()N ............. 8
Piezas y herramientae ................................... 8
Requieitos de ubicaei6n ................................ 8
Requieitos el_otrieos .................................... 9
Preparaci6n de la superficie de
coccion para la instalaci6n .......................... 10
Instalaci6n de la superficie de cocci6n ....... 10
Conexion del suministro el_ctrico ............... 12
Como fijar lasuperficie de coccion al
mostrador .................................................... 13
Complete la instalaci6n ............................... 13
NUMEROS DE
SERVICIO .......................... CONTRAPORTADA
SleCURITIe DE LA TABLE DE CUlSSON ...... 14
INSTRUCTIONS D'INSTALLATION .............. 14
Outillage et pi_ces ....................................... 14
Exigences d'emplacement .......................... 14
Specifications _lectriques .......................... 15
Preparation de la table de cuisson
pour I'installation ......................................... 16
Installation de la table de cuisson ............... 16
Raccordement _lectrique ............................ 18
Fixation de la table de cuisson au
plan de travail .............................................. 19
Achever I'installation .................................... 19
NUMleROS DE
SERVICE .................. COUVERTURE ARRIERE
iMPORTANT:
Save for local electrical inspector's use.
_nstaHer: Leave installation instructions with the homeowner,
Homeowner: Keep installation instructions for future reference.
I_PORTANTE:
Guarde para tenerlas a disposici6n deI inspector de electricidad local,
_nsta_ador: Deje Ias instrucciones de instalaci6n con el propietario,
Propietario: Conserve las instrucciones de instalaci6n para referencia futura,
iMPORTANT :
Conserver pour consultation par Hnspecteur local des installations electriques.
lnstaHateur : Remettre les instructions d'installation au proprietaire,
Proprietaire : Conserver les instructions d'installation pour reference uiterieure.
8286307
COOKTOP SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
INSTALLATION INSTRUCTIONS
• The cooktop must be a specified cooktop that is approved to
be installed either alone or over an undercounter built-in
Gather the required tools and parts before starting installation.
Tools needed
• Tape measure • Marker or pencil
• Flat-blade screwdriver • Pliers
Parts supplied
• Clamp brackets (2)
• 21/2'' (6.4 cm) clamping screws (2)
Parts needed
• A UL listed or CSA approved conduit connector
• ULlisted wire nuts
Check local codes. Check existing electrical supply. See
"Electrical Requirements."
All electrical connections should be made by a licensed, qualified
electrical installer.
Make sure you have everything needed for correct installation. It
is the responsibility of the installer to comply with the installation
clearances specified in these instructions.
IMPORTANT: Observe all governing codes and ordinances.
When installing cooktop, use minimum dimensions given.
• To eliminate the risk of burns or fire by reaching over the
heated surface units, cabinet storage space located above
the surface units should be avoided. If cabinet storage is to
be provided, the risk can be reduced by installing a range
hood that projects horizontally a minimum of 5" (12.7 cm)
beyond the bottom of the cabinets.
oven. Check the cooktop burner box for an approved
installation label. If you do not find this label, contact your
dealer to confirm that your cooktop is approved.
• Ovens approved for this type of installation will have an
approval label located on the top of the oven. If you do not
find this label, contact your dealer to confirm that your oven is
approved. Refer to oven manufacturer's Installation
Instructions for approval for built-in undercounter use and
proper cutout dimensions.
• When installing cooktop over an undercounter built-in oven,
do not fasten cooktop to countertop with clamps. This will
make the cooktop easier to remove if future servicing
becomes necessary.
• The cooktop should be installed away from strong draft
areas, such as windows, doors, fans or strong heating vents.
The cooktop should be located for convenient use in the
kitchen.
• Use the countertop opening dimensions that are given with
these Installation Instructions. Given dimensions are
minimum clearances and provide 0" (0 cm) clearance.
• Grounded electrical supply is required. See "Electrical
Requirements" section.
Product Dimensions
\
X
A
\ c
A. 21%e" (54.! cm)
B. 30%6" (77.1 cm)
36%6" (92.3 cm)
C. 27/8"(7.3 cm)
Installation Clearances
C
NOTE: After you make the countertop cutout, some installations
may require notching down the base cabinet side walls to clear
the burner box. To avoid this modification, use a base cabinet
with sidewalls wider than the cutout.
If cabinet has a drawer, a 3" (7.6 cm) depth clearance from the
countertop to the top of the drawer (or other obstruction) in base
cabinet is required.
When installing a hood above the cooktop, follow the hood
instructions for dimensional clearances above the cooktop
surface.
Electrical Shock Hazard
Disconnect power before servicing.
Use 8 gauge copper wire.
Electrically ground cooktop.
Failure to follow these instructions can result in death,
fire, or electrical shock.
A. 30" (76.2 cm) on 30" (76.2 cm) models; 36" (91.4 cm) on
36" (91.4 cm) models
B. Combustible area above countertop (shown by dashed box above)
C. 30" (76.2 cm) minimum clearance between top of cooktop platform
and bottom of unprotected wood or metal cabinet (24" [61 cm]
minimum clearance if bottom of wood or metal cabinet is protected
by not less than V4"[0.6 cm] flame retardant millboard covered with
not less than No. 28 MSG sheet steel, 0.015" [0.04 cm] stainless
steel, or 0.024" [0.06 cm] aluminum or 0.020" [0.05 cm] copper)
D. 13" (33 cm) recommended upper cabinet depth
E. 2"(5.! cm)
F. 20_2" (52 cm)
G. 18" (45.7 cm) minimum clearance from upper cabinet to countertop
within minimum horizontal clearances to cooktop
H. Junction box or outlet," !2" (30.5 cm) minimum from bottom of
countertop; 10" (25.4 cm) from right side of cabinet
I. !4_2" (36.8 cm) on 15" (38.1 cm) models; 29_/2'' (74.9 cm) on
30" (76.2 cm) models; 35_2" (90.2 cm) on 36" (91.4 cm) models
J. 1" (2.5 cm) minimum distance to nearest left and right side
combustible surface above cooktop
K. !_/2'' (3.8 cm) max. counter thickness on 15" (38.1 cm) models. See
following illustration.
L. !" (2.5 cm) minimum clearance between back waft and countertop
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that
the ground path and wire gauge are in accordance with local
codes.
Do not ground to a gas pipe.
Check with a qualified electrical installer if you are not sure the
cooktop is properly grounded.
Do not have a fuse in the neutral or ground circuit.
Make sure that the electrical connection and wire size are
adequate and in conformance with the National Electrical Code,
ANSl/NFPA 70-latest edition or CSA Standards C22.1-94,
Canadian Electrical Code, Part 1 and C22.2 No. O-M91-1atest
edition, and all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
Before You Make the Electrical Connection:
To properly install your cooktop, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.
• A 4-wire or 3-wire, single phase, 240 volt, 60 Hz., AC only
electrical supply is required on a separate, 40-amp circuit,
fused on both sides of the line.
The cooktop should be connected directly to the junction box
through flexible, armored or nonmetallic sheathed, copper
cable. The flexible, armored cable extending from the fuse
box or circuit breaker box should be connected directly to the
junction box.
Locatethejunctionboxtoallowasmuchslackaspossible
betweenthejunctionboxandthecooktopsothatthe
cooktopcanbemovedifservicingbecomesnecessaryinthe
future.
• Donotcuttheconduit.Usethelengthofconduitprovided.
• AULlistedorCSAapprovedconduitconnectormustbe
providedateachendofthepowersupplycable(atthe
cooktopandatthejunctionbox).Alistedconduitconnector
isalreadyprovidedatthecooktop.
• Ifthehousehasaluminumwiring,connectthealuminum
wiringtothecopperwirebyusingspecialconnectors
designedandULlistedforjoiningcoppertoaluminum.
Followtheelectricalconnectormanufacturer'srecommended
procedure.Aluminum/copperconnectionmustconformwith
localcodesandindustryacceptedwiringpractices.
t:
1=
Decide on the final location for the cooktop. Locate existing
wiring to avoid drilling into or severing wiring during
installation.
2.
Place the cooktop upside down on a protective surface.
3.
Remove foam strip from literature packing. Remove backing
from foam strip. Apply foam strip adhesive-side down around
bottom of cooktop, flush with edge.
NOTE: The foam strip protects the underside of the cooktop
glass from debris and helps the cooktop sit flat on uneven
counters.
Style 2: Cooktop over cabinets
1. Determine whether your cabinet construction provides
clearance for installing clamp brackets at burner box ends.
This is the recommended location. Clamp brackets can be
installed on the front and back of burner box bottom, if
necessary.
............................... C
\
E
A.Attachment screw holes foroptional frontand
back location
B.Clamp bracket (endlocations recommended)
C. Burnerbox bottom
D.Attachment screw
E.Attachment screw location (recommended)
2. The clamp brackets can be installed before or after the
cooktop is placed into the cutout. Complete the following
steps for the option you choose.
Installing Brackets Before Placing Cooktop in Cutout
1. Remove the attachment screws for the selected bracket
locations from the bottom of the burner box.
2. Select bracket mounting holes that will allow the bracket to
extend far enough out from the cooktop for the installation of
21/2'' (6.4 cm) clamping screws. See "Attach Cooktop to
Countertop" for illustration of clamping screw installation.
A. Burner box
B. Foam strip
Style 1: Cooktop over undercounter built-in oven
IMPORTANT: Clamp brackets should not be used.
1. Turn cooktop right side up.
2. Place cooktop in cutout.
NOTE: Make sure that the front edge of the cooktop is
parallel to the front edge of the countertop. If repositioning is
needed, lift entire cooktop up from cutout to avoid scratching
the countertop.
A. Edge of burner box bottom
B. Clamp bracket
3. Attach brackets to burner box bottom with bracket
attachment screws using the bracket mounting holes
selected in Step 2.
4. Rotate brackets so they do not extend beyond edge of
burner box.
5. Tighten screws just enough to hold brackets in place when
cooktop is put in cutout.
6. Turn the cooktop right side up and place in cutout.
NOTE: Make sure that the front edge of the cooktop is
parallel to the front edge of the countertop. If repositioning is
needed, lift entire cooktop up from cutout to avoid scratching
the countertop.
7. Loosen the screws and rotate the brackets so that they are
perpendicular to the edge of the burner box and extend
beyond its edge. Securely tighten screws.
Installing Brackets After Placing Cooktop in Cutout
1. Place cooktop in cutout.
NOTE: Make sure that the front edge of the cooktop is
parallel to the front edge of the countertop. If repositioning is
needed, lift entire cooktop up from cutout to avoid scratching
the countertop,
2. Remove the attachment screws for the selected bracket
locations from the bottom of the burner box,
3. Select bracket mounting holes that will allow the bracket to
extend far enough out from the cooktop for the installation of
21/2'' (6,4 cm) clamping screws
F
A /
E
__ _ .....................D
C
A, Glasscooktop
B,Burner box
C,Attachment screw
D.Clampbracket (extends far enough beyond
burner box to allow installation of clamping
screws)
E.2_/2'' (6.4cm) clampingscrew (tobe installed in
"Attach Cooktop to Countertop')
E Countertop
4=
Attach brackets to burner box bottom with bracket
attachment screws using the bracket mounting holes
selected in Step 3, Securely tighten screws,
3. Connect the flexible cable conduit from the cooktop to the
junction box using a UL listed or CSA approved conduit
connector.
4. Tighten screws on conduit connector if present.
5. Complete installation following instructions for your type of
electrical connection:
4-wire (recommended)
3-wire (if 4-wire is not available)
Electrical Connection Options
If your home has: And you will be
Go to Section:
connecting to:
4-wire direct A fused 4-Wire Cable from
disconnect or Power Supply
circuit breaker
box
(12.7 cm)
3-wire direct A fused 3-Wire Cable from
disconnect or Power Supply
circuit breaker
box
4-Wire Cable from Power Supply
IMPORTANT: Use the 4-wire cable from power supply where local
codes do not permit connecting the frame-ground conductor to
the neutral (white) junction box wire.
A
B
Electrical Shock Hazard
Disconnect power before servicing.
Use 8 gauge copper wire.
Electrically ground cooktop.
Failure to follow these instructions can result in death,
fire, or electrical shock.
This cooktop is manufactured with a frame connected, green or
bare ground wire, Connect the cooktop cable to the junction box
through the UL listed or CSA approved conduit connector.
1. Disconnect power.
2. Remove junction box cover, if present.
A. Cable from power supply
B. Red wires
C. Green (or bare) ground wires
D. 4-wire cable from cooktop
E.Junction box
F. White wires
G. UL listed wire nut
H. Black wires
L UL listed or CSA approved
conduit connector
1. Connect the 2 black wires together using a UL listed wire nut.
2. Connect the 2 red wires together using a UL listed wire nut.
3. Connect the 2 white wires together using a UL listed wire nut.
4. Connect the green (or bare) ground wire from the cooktop
cable to the green (or bare) ground wire (in the junction box)
using a UL listed wire nut.
5. Replace junction box cover.
6. Reconnect power.
3-Wire Cable from Power Supply
IMPORTANT: Use the 3-wire cable from power supply where local
codes permit connecting the frame-ground conductor to the
neutral (white) junction box wire:
A
E
F
H
C
D
A. Cable from power suppiy
B. Red wires
C. White and green (or bare)
ground wires (from cooktop)
D.4-wire cable from cooktop
E.Junction box
F. White wire (from power supply)
G. UL listed wire nut
H. Black wires
L UL listed or CSA approved
conduit connector
1. Connect the 2 black wires together using a UL listed wire nut.
2. Connect the 2 red wires together using a UL listed wire nut.
3. Connect the green or bare and white cooktop cable wires to
the white (neutral) wire in the junction box using a UL listed
wire nut.
4. Replace junction box cover.
5. Reconnect power.
NOTE: This section applies only if you are using clamp brackets.
A .........................................................
A. Glass cooktop
B. Burner box
C. Clamp bracket
•...................................................................F
D. Countertop
E.2_±" (6.4 cm) clamping screw
F. Attachment screw
/ ........................................O
1. Place the 21/2'' (6.4 cm) clamping screws into the brackets.
2. Check to be sure the cooktop is still level.
3. Use a flat-blade screwdriver to tighten the screws against the
countertop. Do not overtighten.
1. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped,
2. Dispose of/recycle all packaging materials.
3. Use a mild solution of liquid household cleaner and warm
water to remove waxy residue caused by protective shipping
material, Dry thoroughly with a soft cloth. For more
information, see the "Cooktop Care" section of the
Use and Care Guide.
4. Read "Cooktop Use" in the cooktop Use and Care Guide.
NOTE: If the cooktop does not work after turning on the power,
check that a circuit breaker has not tripped or a household fuse
has not blown. See "Troubleshooting" section in the Use and
Care Guide for further information.
If you need Assistance or Service:
Please reference the "Assistance or Service" section of the Use
and Care Guide or contact the dealer from whom you purchased
your cooktop.
Loading...