Kenmore Elite 10678586800, 59677592800, 59677593800, 59677594800, 59677596800 Owner’s Manual

...

L 1 T

Models/Modelos/Mod_les

596.7759_800

596.7760_800

596.7857_800

596.7858_800

-I

mint(io

Bottom-Mount Refrigerator

Refrigerador con congelador en la parte inferior

R6frig6rateur b cong61ateur en bas

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com

W10182820A Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8 www.sears.ca

TABLEOF CONTENTS

WARRANTY ..................................................................................... 2

REFRIGERATOR SAFETY .............................................................. 3

Proper Disposal of Your Old Refrigerator .................................... 3

INSTALLATION INSTRUCTIONS .................................................. 4

Unpack the Refrigerator ............................................................... 4

Location Requirements ................................................................ 4

Electrical Requirements ................................................................ 5

Water Supply Requirements ........................................................ 5

Connect the Water Supply ........................................................... 5

Refrigerator Door(s) and Drawer .................................................. 7

Adjust the Doors ........................................................................... 9

Water System Preparation ........................................................... 9

REFRIGERATOR USE ................................................................. 10

Opening and Closing Doors ...................................................... 10

Using the Controls ..................................................................... 10

Water Dispenser ........................................................................ 12

Water Filter Status Light ............................................................ 12

Water Filtration System ............................................................. 12

Ice Maker ................................................................................... 13

REFRIGERATOR FEATURES ..................................................... 13

Refrigerator Shelves .................................................................. 13

Crisper and Crisper Cover ......................................................... 13

Crisper Humidity Control ........................................................... 14

Gourmet Pantry TM Drawer ......................................................... 14

FREEZER FEATURES .................................................................. 14

Lower Wire Basket .................................................................... 14

DOOR FEATURES ....................................................................... 15

Dairy Center ............................................................................... 15

Door Bins ................................................................................... 15

Grip Pads ................................................................................... 15

Fresh-N-Ready Bin TM ................................................................ 15

REFRIGERATOR CARE ............................................................... 16

Cleaning ..................................................................................... 16

Changing the Light Bulb ............................................................ 16

Power Interruptions ................................................................... 17

Vacation and Moving Care ........................................................ 17

TROUBLESHOOTING .................................................................. 18

Refrigerator Operation ............................................................... 18

Temperature and Moisture ........................................................ 19

Ice and Water ............................................................................. 19

PROTECTION AGREEMENTS .................................................... 20

ACCESSORI ES ............................................................................. 20

WATER FILTER CERTIFICATIONS ............................................ 20

PRODUCT DATA SHEETS .......................................................... 21

SERVICE NUMBERS ............................................... BACK COVER

KENMORE ELITE®APPLIANCE WARRANTY

ONE YEAR LIMITED WARRANTY

When installed, operated and maintained according to all instructions supplied with the product, if this appliance fails due

to a defect in material or workmanship within one year from the

date of purchase, call 1-800-4-MY-HOME ®to arrange for free repair.

If this appliance is used for other than private family purposes,

this warranty applies for only 90 days from the date of purchase.

FIVE-YEAR LIMITED WARRANTY ON SEALED REFRIGERATION SYSTEM

For five years from the date of purchase, when this refrigerator is operated and maintained according to the instructions supplied with it, Sears will repair the sealed system (consisting of refrigerant, connecting tubing, and compressor), free of charge, if defective in materials or workmanship.

THIS WARRANTY COVERS ONLY DEFECTS IN MATERIAL AND WORKMANSHIP. SEARS WILL NOT PAY FOR:

1. Expendable items that can wear out from normal use, including but not limited to filters, belts, light bulbs, and bags.

2. A service technician to instruct the user in correct product installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed,

operated or maintained according to all instructions supplied with the product.

5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose.

6. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than those recommended in all instructions supplied with the product.

7. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

Customer's sole and exclusive remedy under this limited warranty shall be product repair as provided herein. Implied warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law. Sears shall not be liable for incidental or consequential damages. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, or limitations on the duration of implied warranties of merchantability or fitness, so these exclusions or limitations may not apply to you.

This warranty applies only while this appliance is used in the United States and Canada.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co.

Hoffman Estates, IL 60179

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2B8

PRODUCT RECORD

In the space below, record your complete model number, serial number, and purchase date. You can find this information on the model and serial number label located on the product.

Have this information available to help you obtain assistance or service more quickly whenever you contact Sears concerning your appliance.

Model number

Serial number

Purchase date

Save these instructions and your sales receipt for future reference.

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:To reduce the risk of fire, electric shock, or injury to persons when using the refrigerator, follow basic precautions,

including the following:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

SAVETHESEINSTRUCTIONS

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline, away from refrigerator.

[] Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker kit ready models only).

Proper Disposal of Your Old Refrigerator

Suffocation Hazard Remove doors from your old refrigerator. Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily climb inside.

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For more information, see "Refrigerator Safety."

• Dispose of/recycle all packaging materials.

When Moving Your Refrigerator: Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor. Always pull the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move it, as floor damage could occur.

LO(,,<__£fI Fleql.lI;l(_ mel"_ts

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for a W' (1.25 cm) space at the top and behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line connections. When installing your refrigerator next to a fixed wall, leave a 3%" (9.5 cm) minimum space between the refrigerator and wall to allow the door to swing open.

NOTE: It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source. Do not install the refrigerator in a location where the temperature will fall below 55°F (13°C).

Clean Before Using

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions in "Refrigerator Care."

important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when

removing them to avoid impact from dropping.

1/2" (1.25 cm) /

E ]

3%" (9.5cm)

ElectricalShockHazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire_ or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an

extension cord. NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn Cooling OFF,and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and turn Cooling ON. See "Using the Controls."

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver • 1/4II Nut driver

• 7/16IIand 1/211Open-end or two • 1/411Drill bit adjustable wrenches • Cordless drill

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Do not use a piercing-type or 3/16II(4.76 mm) saddle valve which reduces water flow and clogs more easily.

• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain

above freezing.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 35 and 120 psi (241 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 4O

to 60 psi (276 to 414 kPa):

Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

Allow the storage tank on the reverse osmosis system to refill after heavy usage.

If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. See "Water Filtration System."

If you have questions about your water pressure, call a licensed, qualified plumber.

Read all directions before you begin. IMPORTANT: If you turn the refrigerator on before the water line

is connected, turn the ice maker OFR

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Find a 1/2"to 11/4'' (12.7 mm to 31.8 mm) vertical cold water pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the bottom. This will help keep water away from the drill. This also keeps normal sediment from collecting in the valve.

Determine the length of copper tubing you need. Measure from the connection on the rear of the refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

Using a cordless drill, drill a 1/4"hole in the cold water pipe you have selected.

........ A

Water Pressure

A cold water supply with water pressure of between 35 and 120 psi (241 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

A. Cold water pipe

B. Pipe clamp C. Copper tubing D. Compression nut

E. Compression sleeve F. Shutoff valve

G. Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the 1/4"drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe.

Connect to Refrigerator

Depending on your model, the water line may come down from the top or up from the bottom. Follow the connection instructions for your model.

Style 1

1. Remove plastic cap from water valve inlet port. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Confirm copper tubing is secure by pulling on copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks when coiling the copper tubing. Secure copper tubing to refrigerator cabinet with a "P" clamp.

4. Slide the compression nut over the sleeve and screw into the water valve inlet port.

A. Plastic water tubing C. Compression nut

B.Sleeve D. Copper tubing

Using an adjustable wrench, hold the nut on the plastic water line to keep it from moving. Then, with a second wrench turn

the compression nut on the copper tubing counterclockwise to completely tighten. Do not overtighten.

A. Plastic water line D. Copper tubing B. Water valve inlet port E. "P" clamp C. Compression nut

B_ @

C D i E i

A. Copper tubing D. Compression sleeve B. "P" clamp E. Water valve inlet port

C. Compression nut

3. Turn on water supply to refrigerator and check for leaks. Correct any leaks.

Style 2

1. Create a service loop (minimum diameter of 2 ft [61 cm]) with the copper tubing. Avoid kinks when coiling the copper tubing.

2. Remove the plastic cap from water valve inlet port. Place a compression nut and sleeve on the copper tubing.

3. Insert the end of the copper tubing into the water valve inlet port. Shape tubing slightly so that the tubing feeds straight into the port to avoid kinks.

6. Check connection by pulling on copper tubing. Attach copper tubing to refrigerator cabinet with a "P" clamp. Turn on water

supply to refrigerator and check for leaks. Correct any leaks.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill the ice container.

Graphicsareincludedlaterinthissection.

Remove and Replace Handles

1. Using a %2" Allen wrench, loosen the two set screws located on the side of each handle. See Graphics 1 and 2.

2. Pull the handle straight out from the door. Make sure you 3. keep the screws for reattaching the handles,

3. To replace the handles, reverse the directions.

Remove Doors and Hinges

Electrical Shock Hazard

Disconnect power before removing doors. Failure to do so can result in death or electrical shock.

IMPORTANT:

• Remove food and any adjustable door or utility bins from doors,

• All graphics referenced in the following instructions are included later in this section after "Final Steps."

TOOLS NEEDED: %6", %", 1/4"hex-head socket wrench, #2 Phillips screwdriver, and a flat-blade screwdriver.

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the refrigerator door while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working.

Starting with the right-hand side door, remove the parts for the top hinge as shown in Top Hinge graphic. Lift the refrigerator door from the bottom hinge pin,

NOTE: On some models, remove the shim from the bottom hinge pin and keep it for later use. See Bottom Hinge graphic,

Before removing the left-hand side door, disconnect the wiring plug located on top of the top hinge by wedging a flat- blade screwdriver or your fingernail between the two sections. See Wiring Plug graphic.

NOTE: The green, ground wire remains attached to the hinge,

Remove the parts for the top hinge as shown in Top Hinge graphic. Lift the left-hand side door from the bottom hinge pin.

NOTE: On some models, remove the shim from the bottom hinge pin and keep it for later use. See Bottom Hinge graphic.

2. Replace the partsforthe bottom hingeas shown inBottom

Hinge graphic.Tightenscrews.Replacetherefrigeratordoor. NOTE: Provideadditionalsupportforthe refrigeratordoor

whilethe hingesarebeingmoved. Do notdepend on thedoor gasketmagnets to holdthedoor inplacewhileyou are

working. Align the door so that the bottom of the refrigerator door

aligns evenly with the top of the freezer drawer. Tighten all screws,

Reconnect the wiring plug on top of the left-hand side refrigerator door.

5. Replace the top hinge covers.

Remove and Replace Freezer Drawer Front

IMPORTANT: Two people may be required to remove and replace the freezer drawer front. Graphics are included later in this

section.

Remove Drawer Front

1. Open the freezer drawer to full extension.

2. Loosen the four screws attaching the drawer glides to the drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws in the drawer front.

3. Lift drawer front upward and off the screws. See Drawer Front Removal graphic.

Replace Drawer Front

1. Slide the drawer glides out of the freezer compartment. Insert

the screws in the top of the drawer front into the slots in the drawer brackets. See Drawer Front Replacement graphic.

2. Pull the drawer brackets toward you to position the two screws in the bottom of the drawer front into the brackets.

See Drawer Front Replacement graphic.

3. Completely tighten the four screws.

Final Steps

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Replace Doors and Hinges

1. Assemble the parts for the top hinge as shown in Top Hinge

graphic. Do not tighten the screws completely.

1. Plug in refrigerator to a grounded 3 prong outlet.

2. Return all removable door parts to doors and food to refrigerator.

Top Hinges

A. Hinge Cover Screw B. Top Hinge Cover

C. 5A6"Hex-Head Hinge Screws D. Top Hinge

Bottom Hinges

o_ ............. A

_. c

A. Shim (on some models)

B. Bottom Hinge C. Hinge Screws

Wiring Plug

A. %2" Set Screw

A. Loosen 4 Door Bracket Screws

Adi , te Doot s

Your refrigerator has two adjustable, front leveling screws - one on each side of the refrigerator base. If your refrigerator seems unsteady or you want the door to close more easily, use the

instructions below.

1. Remove the base grille. Grasp the grille firmly and pull it toward you.

2. Raise or lower the cabinet.

Using a %" hex driver, turn the roller adjustment screw(s) on each side to raise or lower that side of the refrigerator.

NOTE: Having someone push against the top of the refrigerator takes some weight off the adjustment screws and

rollers. This makes it easier to turn the screws. It may take several turns of the roller adjustment screw to adjust the tilt of

the refrigerator.

• To raise, turn the roller adjustment screw to the right.

• To lower, turn the roller adjustment screw to the left. Turn the brake foot clockwise until it is firmly against the floor

to keep the refrigerator from rolling forward when the freezer drawer is pulled open.

Please read before using the water system. Immediately after installation, follow the steps below to make

sure that the water system is properly flushed.

1. Turn off the ice maker by opening the freezer door and lifting up the wire shutoff arm as shown.

Install the interior water filter. The interior water filter mounting bracket is located on the left side wall of the refrigerator compartment.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

Remove blue bypass cap and retain for later use. Carefully remove the interior water filter from its

packaging. Remove the sealing label from the end of the filter and insert it into the filter head.

Gently rotate the filter clockwise until it stops. Then snap the filter cover closed.

A. Rear roller adjustment screw

B. Front roller adjustment screw C. Brake foot

NOTE: Your refrigerator may have a rear roller adjustment screw on each side. To raise or lower the rear of the

refrigerator, use a %" hex driver to turn the screws.

Open the door again to make sure that it closes as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws clockwise. It may take several more turns, and you should turn both screws the same

amount.

4. Replace the base grille.

Press the Water button on the dispenser control panel. Use a sturdy container to depress and hold the dispenser lever for 5 seconds, then release it for 5 seconds. Repeat until water begins to flow. Once water begins to flow, continue depressing and releasing the dispenser lever (5 seconds on, 5 seconds off) for an additional 2 minutes. This will flush air from the filter and water dispensing system. Additional flushing may be required in some households. As air is cleared from the system, water may spurt out of the dispenser.

NOTE: After five minutes of continuous dispensing, the dispenser will stop dispensing water to avoid flooding. To continue dispensing, remove the container and press the dispensing lever again.

Inspect the filter system for water leaks. If you see water leaks, see the "Troubleshooting" section.

Turn on the ice maker by opening the freezer door and lowering the wire shutoff arm as shown. Please refer to the "Ice Maker" section for further instructions on the operation of your ice maker.

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced.

REFRIGERATOR USE

, .%,_/

There are two refrigerator compartment doors. The doors can be

opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

• When the left side door is opened, the hinged seal automatically folds inward so that it is out of the way.

• When both doors are closed, the hinged seal automatically forms a seal between the two doors.

A. Hinged seal

...._(Jl [[01_::>

IMPORTANT:

• When the power is on, the temperature display shows the actual temperature of the compartment.

• Wait 24 hours for your refrigerator to cool completely before adding food. If you add food before the refrigerator has cooled completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer temperature controls to a colder than recommended setting will not cool the compartments any faster.

The recommended settings should be correct for normal household refrigerator use. The controls are set correctly when milk or juice is as cold as you like and when ice cream

is firm.

• If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls.

Temperature Controls

For your convenience, your temperature controls are preset at

the factory. When you first install your refrigerator, make sure the

controls are still set to the recommended set points as shown.

Recommended Settings

To Turn Cooling Off/On:

Press the Freezer Up Arrow until OFF appears in the display. Neither compartment will cool. Press either the Freezer or Refrigerator Down Arrow to turn the cooling back on.

Adjusting Controls

The REFRIGERATOR control adjusts the refrigerator compartment temperature. The FREEZER control adjusts the freezer compartment temperature.

If you need to adjust the temperature in either the refrigerator or freezer compartment, use the settings listed in the chart as a guide.

To Adjust Set Point Temperatures: The first touch of the Up Arrow or Down Arrow displays the

current temperature set point. The display will show the set point for approximately 3 seconds, and then return to the actual temperature.

• Press the Up Arrow or Down Arrow touch pads until the desired temperature set point is displayed.

NOTE: Except when first turning on the refrigerator, do not adjust either temperature control more than one setting at a time. Wait 24 hours for the temperature to stabilize between adjustments.

CONDITION/REASON: ADJUSTMENT: REFRIGERATOR too warm REFRIGERATOR

Control 1° lower

FREEZER too warm/too little ice FREEZER Control 1°

lower

REFRIGERATOR too cold REFRIGERATOR

Control 1° higher

FREEZER too cold FREEZER Control 1°

higher

Additional Control Center Features

Grocery Savor

The Grocery Savor feature assists with periods of high refrigerator use, full grocery loads, or temporarily warm room temperatures.

• Press the Grocery Savor touch pad to set the freezer and refrigerator to the lowest temperature settings. Press the Grocery Savor touch pad again to return to the normal refrigerator set point.

NOTE: The Grocery Savor feature will automatically shut off in approximately 12 hours. When Grocery Savor is on, you cannot adjust the temperature in either compartment.

Fr_zBr

Recommended Setting (0 +)

Refrigerator

Recomm_ded Settlng (38 +)

Acceler-lce

The Acceler-lce feature assists with temporary periods of heavy ice use by increasing ice production.

• Press Acceler-lce to set the freezer to the lowest temperature settings. Press Acceler-lce again to return the freezer to the normal set point.

NOTE: The Acceler-lce feature will automatically shut off in approximately 24 hours. When Acceler-lce is on, you cannot adjust the freezer temperature.

Door Ajar

The Door Ajar feature sounds a chime every few seconds when the refrigerator door has been left open for 5 continuous minutes.

The chime will sound until the door is closed or Door Ajar is turned off. The lights bulbs will turn off if any door is left open for

6 continuous minutes. Closing all the doors for 1 second will cause the lights to come back on.

• Press the Door Ajar touch pad to turn this feature on or off. The indicator light will be lit when the Door Ajar feature is on.

Humidity Control (on some models)

The Humidity Control feature turns on a heater to help reduce moisture on the door hinge seal. Use in humid environments or when you notice moisture on the door hinge seal. The refrigerator uses more energy when Humidity Control is on.

• Press Humidity Control when the environment is warm and more humid, or if you notice moisture on the door hinge seal. The indicator light will be lit when humidity control is ON.

Press Humidity Control again to turn OFF and save energy when the environment is less humid.

Temp Alarm (on some models)

The Temp Alarm feature provides temperature information in the event of a power outage.

Power outage: During a power outage, if the temperatures in the refrigerator and freezer compartments exceed normal operating temperatures, the highest temperature reached will be displayed.

• Press the Temp Alarm touch pad until the indicator light is lit, to turn on this feature. Press and hold Temp Alarm for 3 seconds until the indicator light goes off to turn off this

feature.

Temperature alarm: An alarm will sound repeatedly if the freezer or refrigerator compartment temperatures exceed normal operating temperatures for an hour or more.

The temperature displays will alternately show the current temperatures and the highest temperatures the compartments

reached.

Press the Temp Alarm touch pad once to stop the audible alarm and alternating temperature displays. The Temp Alarm light will continue to flash until the refrigerator returns to the set temperature.

Filter Reset (on some models)

The Filter Reset control allows you to restart the water filter status tracking feature each time you replace your water filter. See "Water Filtration System."

• Press and hold the Filter Reset touch pad for 3 seconds, until the Replace light turns off.

Good Replace

User Preferences

The control center allows you to set user preferences, if desired.

Temperature Display (F_C)

This preference allows you to change the temperature display. F - Temperature in degrees Fahrenheit C - Temperature in degrees Celsius

Alarm (AL)

This preference allows you to turn off the sound of all alarms. ON - You will hear the alarm sound.

OFF - You will not hear the alarm sound.

Sabbath Mode (SAB)

ON - All control center lights, interior lights and alarm tones will be disabled.

OFF - All control center lights, interior lights and alarm tones will be enabled.

NOTE: Press the door alarm touch pad for three seconds to restore all lights.

To Access the User Preferences Menu:

1. Press and hold the Door Alarm touch pad for three seconds. The preference name will appear in the Freezer display and the preference status (F or C) or (ON or OFF) will appear in the Refrigerator display.

2. Use the Freezer (+) or (-) touch pads to scroll through the preference names. When the desired preference name is displayed, press the Refrigerator (+) or (-) touch pads to change the preference status.

3. Set your preferences by pressing and holding the Door Alarm touch pad for three seconds.

IMPORTANT:

• If you did not flush the water system when the refrigerator was first installed, see "Water System Preparation" for instructions on flushing the water system.

• Allow 24 hours for the refrigerator to cool down and chill water. Dispense enough water every week to maintain a fresh supply.

Dispensing Water

1. Hold a container under the dispenser while pressing the button.

2. Release the button to stop dispensing.

_Jd_,et' :s: ..... ,. ,,,

IMPORTANT:

• The water filter should be replaced when the Replace status light is lit or earlier if the flow of water to your water dispenser or ice maker decreases noticeably.

• Air trapped in the system may cause water and the water filter to eject. Dispense water for 2 minutes before removing

the used water filter.

Replacing the Water Filter

The water filter mounting bracket is located on the right side of the refrigerator compartment.

1. Turn the used water filter counterclockwise until it releases from the filter mounting bracket.

2. Drain water from the water filter into the sink, and discard the used water filter. Wipe up the excess water in the filter cover.

3. Remove the sealing label from the end of the new water filter and insert the water filter into the filter mounting bracket. Gently rotate the water filter clockwise until it stops, and snap

the filter cover closed.

The water filter status light will help you know when to change the water filter. When the Replace light is on, a new water filter

should be installed.

After replacing the water filter, press and hold FILTER RESET for

3 seconds until the Replace light turns off. See "Using the Controls."

Non-Indicator Water Filter

If your refrigerator does not have a water filter status light, you should change the water filter every 6 months depending on your usage. Ifthe water flow to the dispenser or ice maker decreases noticeably before 6 months have passed, replace the water filter

more often.

4. Flush the water system. See "Water System Preparation."

5. Inspect the water filter system for leaks. If you see water leaks, see "Troubleshooting."

Using the Dispenser Without a Water Filter

You can use the water dispenser without a water filter, but your water will not be filtered. Ifyou choose this option, replace the water filter with the blue bypass cap.

Turning the Ice Maker On/Off

Toturn the ice maker ON, simply lower the wire shutoff arm. Tomanually turn the ice maker OFF, lift the wire shutoff arm to the

OFF (arm up) position and listen for the click. NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin and the ice cubes will raise the wire shutoff arm to the OFF (arm up) position. Do not force the wire shutoff arm up or down.

Ice Production Rate

• The ice maker should produce a complete batch of ice approximately every 3 hours.

• To increase ice production, lower the freezer and refrigerator temperature. See "Using the Controls." Wait 24 hours between adjustments.

Remember

• Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.

• Do not store anything on top of the ice maker or in the ice storage bin.

REFRIGERATOR FEATURES

Your model may have some or all of these features.

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when removing them to avoid impact from dropping.

The shelves in your refrigerator are adjustable to meet your individual storage needs.

Storing similar food items together in your refrigerator and adjusting the shelves to fit different heights of items will make finding the exact item you want easier. It will also reduce the amount of time the refrigerator door is open, and save energy.

Shelves and Shelf Frames

To remove and replace a shelf/shelf frame:

1. Remove the shelf/frame by tilting it up at the front and lifting it

out of the shelf supports.

2. Replace the shelf/frame by guiding the rear shelf hooks into the shelf supports. Tilt the front of the shelf up until rear shelf hooks drop into the shelf supports.

3. Lower the front of the shelf and make sure that the shelf is in position.

To remove and replace the crisper(s}:

1. Slide crisper(s) straight out to the stop. Lift the front of the crisper(s) and slide out the rest of the way.

2. Replace the crisper(s) by sliding back in fully past the drawer stop.

To remove the crisper(s) cover:

1. Remove crisper(s).

2. Holding the glass insert firmly with one hand, press up in center of glass insert until it rises above the plastic frame.

Gently, slide the glass insert forward to remove.

3. Lift the cover frame up and remove it.

To replace crisper(s) cover:

1. Fit back of cover frame into supports on side walls of the refrigerator and lower the front of the cover frame into place.

2. Slide rear of glass insert into cover frame and lower front into place.

You can control the amount of humidity in the moisture-sealed crisper. Adjust the control to any setting between LOW and

HIGH. LOW (open) lets moist air out of the crisper for best storage of

fruits and vegetables with skins.

• Fruit: Wash, let dry and store in refrigerator in plastic bag or crisper. Do not wash or hull berries until they are ready to use. Sort and keep berries in original container in crisper, or store in a loosely closed paper bag on a refrigerator shelf.

• Vegetables with skins: Place in plastic bags or plastic container and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage of

fresh, leafy vegetables.

• Leafy vegetables: Wash in cold water, drain and trim or tear off bruised and discolored areas. Place in plastic bag or plastic container and store in crisper.

Drawer Temperature Control

The temperature control, located under the lid on the right-hand side of the drawer, regulates the amount of cold air coming into

the drawer. NOTE: Cold air directed into the drawer can decrease the

refrigerator temperature. The refrigerator temperature may need to be adjusted.

• Slide the temperature control to the least cold setting if you want the drawer to be the same temperature as the refrigerator compartment.

• Slide the temperature control to a colder setting when you want the drawer to be colder than the refrigerator compartment.

NOTE: Use the coldest setting when storing meats.

Colder

The full-width, temperature-controlled drawer can be used to

store large party trays, dell items, or beverages. For storage flexibility the drawer features a divider and an adjustable temperature control.

NOTE: Do not place leafy vegetables in the temperature-

controlled drawer. Colder temperatures could damage leafy

produce.

Drawer Removal and Replacement

To remove the drawer:

1. Lift the lid. Pull the drawer out to its full extension.

2. Tilt up the front of the drawer and pull it straight out.

To replace the drawer:

1. Push the metal glide rails to the rear of the refrigerator.

2. Place the drawer onto the glide rails and slide the drawer toward the rear of the refrigerator.

Drawer Divider

To remove the divider:

1. Pull the drawer out to its full extension.

2. Lift the front of the divider to unhook it from the rear wall of the drawer and lift the divider out.

To replace the divider:

1. Hook the back of the divider over the rear wall of the drawer.

2. Lower the divider into place.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and moisture-proof. Rewrap if necessary. See the following chart for storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish ......................... use same day as purchased

Chicken, ground beef, variety meats (liver) ...................... 1-2 days

Cold cuts, steaks/roasts ................................................... 3-5 days

Cured meats ................................................................... 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or plastic containers with tight lids.

FREEZER FEATURES

Your model may have some or all of these features.

To remove wire basket: Pull drawer open to full extension. Tilt the lower basket forward

and lift out.

To replace wire basket:

Tilt the lower basket front down and set the basket into the drawer rail.

DOOR FEATURES

Your model may have some or all of these features.

To remove and replace the dairy center:

1. Remove the dairy center by raising and holding the cover up while lifting the dairy center up and pulling it straight out.

2. Replace the dairy center by sliding it in above the desired support and pushing it down until it stops.

©oo Bns

To remove and replace the bins:

1. Remove the bin by lifting it up and pulling it straight out.

2. Replace the bin by sliding it in above the desired support and pushing it down until it stops.

To Remove and Replace the Bin Parts:

1. Press either release button to open the tilt-out portion of the bin.

A. Release buttons

To remove the tilt-out portion of the bin, press in on the curved levers on each side of the bin. Pull up and out.

NOTES:

• The bin can not be removed if it is tilted out all the way.

Tilt it only part of the way before pressing the curved levers to remove it.

• Clean the parts as instructed in the "Cleaning" section.

, {a_a/s s.£_

Grips pads help keep items from sliding in the door bins. Grip pads are removable and are top-rack dishwasher safe for easy cleaning.

This bin keeps healthy snacks like fresh fruits and vegetables convenient for the whole family. It includes a removable berry

basket for rinsing and storing delicate items like grapes and berries.

To Remove and Replace the Bin:

1. Remove the bin by lifting it and pulling it straight out.

2. Replace the bin by sliding it in above the desired supports and pushing it down until it stops.

A. Curved lever

3. Reinstall the tilt-out portion of the bin. Be sure it is properly

seated in the bottom of the bin before inserting the curved levers into position.

4. Replace the interior parts of the bin.

A. Strainer basket

B. Dividers C. Strainer mat

REFRIGERATOR CARE

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency.

If you need to clean the condenser:

Remove the base grille. Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately. IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator: NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh

cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean sponge or soft cloth and a mild detergent in warm water.

• To keep your stainless steel refrigerator looking like new

and to remove minor scuffs or marks, it is suggested that you use the manufacturer's approved Stainless Steel

Cleaner & Polish. To order the cleaner, see "Accessories." IMPORTANT: This cleaner is for stainless steel parts only! Do not allow the Stainless Steel Cleaner & Polish to come into

contact with any plastic parts such as the trim pieces, dispenser covers or door gaskets. If unintentional contact

does occur, clean plastic part with a sponge and mild detergent in warm water. Dry thoroughly with a soft cloth.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to replace the bulb with an appliance bulb of the same size, shape, and wattage (no greater than 40 watts).

Changing the Refrigerator Light Bulb

1. Unplug the refrigerator or disconnect power.

2. Slide the light shield toward the back of the compartment to release it from the light assembly.

Replace burned-out bulb(s) with appliance bulb(s) no greater than 40 watts.

Replace the light shield by inserting the tabs on the shield into the liner holes on each side of light assembly. Slide the

shield toward the front until it locks into place. NOTE: To avoid damaging the light shield, do not force the

shield beyond the locking point.

5. Plug in refrigerator or reconnect power.

Changing the Freezer Light Bulb

1. Unplug refrigerator or disconnect power.

NOTE: You may need to remove the upper freezer shelf or basket to access the light assembly.

2. The light shield opens from the back. Firmly press forward on the notches in the back of the shield and pull the shield down.

3. Remove the shield and replace the burned-out bulb with an appliance bulb no greater than 40 watts.

4. Insert the front tabs of the shield into the liner and snap the back portion of the shield over the light assembly.

5. Plug in refrigerator or reconnect power.

If the power will be out for 24 hours or less, keep the door or doors closed (depending on your model) to help food stay cold

and frozen. If the power will be out for more than 24 hours, do one of the

following:

• Remove all frozen food and store it in a frozen food locker.

• Place 2 Ibs (907 g) of dry ice in the freezer for every cubic foot (28 L) of freezer space. This will keep the food frozen for 2 to 4 days.

• If neither a food locker nor dry ice is available, consume or can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled one. A freezer full of meat stays cold longer than a freezer full of baked goods. If you see that food contains ice crystals, it may be refrozen, although the quality and flavor may be affected. If the condition of the food is poor, dispose of it.

Vacations

If You Choose to Leave the Refrigerator On While You're

Away:.

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker:

• Depending on your model, raise wire shutoff arm to OFF (up) position, or press the switch to OFR

• Shut off water supply to the ice maker.

3. Empty the ice bin.

If You Choose to Turn the Refrigerator Off Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day ahead of time.

• When the last load of ice drops, raise the wire shutoff arm to the OFF (up) position or press the switch to OFE depending on your model.

3. Turn the Temperature controls off. See "Using the Controls."

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in. This stops odor and mold from building up.

Moving

When you are moving your refrigerator to a new home, follow these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• Disconnect the water line from the back of the

refrigerator.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or press the switch to OFF, depending on your model.

2. Remove all food from the refrigerator and pack all frozen food in dry ice.

3. Empty the ice bin.

4. Turn the Temperature controls off. See "Using the Controls."

5. Unplug refrigerator.

6. Clean, wipe, and dry thoroughly.

7. Take out all removable parts, wrap them well, and tape them together so they don't shift and rattle during the move.

8. Depending on the model, raise the front of the refrigerator so it rolls more easily OR raise the leveling screws so they don't scrape the floor. See "Adjust the Doors."

9. Tape the doors closed and tape the power cord to the back of the refrigerator.

When you get to your new home, put everything back and refer to the "Installation Instructions" section for preparation instructions. Also, if your refrigerator has an automatic ice maker, remember to reconnect the water supply to the refrigerator.

TROUBLESHOOTING

Try the solutions suggested here first inorder to avoid the cost of an unnecessary service call.

The refrigerator will not operate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord, Failure to follow these instructions can result in death,

fire, or electrical shock.

Power cord unplugged? Plug into a grounded 3 prong

outlet. Is outlet working? Plug in a lamp to see if the outlet is

working. Household fuse blown or circuit breaker tripped? Replace

the fuse or reset the circuit breaker, If the problem continues, call an electrician.

Are controls on? Make sure the refrigerator controls are on. See "Using the Controls."

New installation? Allow 24 hours following installation for the refrigerator to cool completely,

NOTE: Adjusting the temperature controls to coldest setting will not cool either compartment more quickly.

The refrigerator seems noisy

Refrigerator noise has been reduced over the years. Due to this reduction, you may hear intermittent noises from your new refrigerator that you did not notice from your old model. Below are listed some normal sounds with explanations.

• Buzzing - heard when the water valve opens to fill the ice

maker

• Pulsating - fans/compressor adjusting to optimize

performance

• Hissing/Rattling - flow of refrigerant, movement of water

lines, or from items placed on top of the refrigerator

• Sizzling/Gurgling - water dripping on the heater during

defrost cycle

• Popping - contraction/expansion of inside walls, especially

during initial cool-down

• Water running - may be heard when water melts during the

defrost cycle and runs into the drain pan

• Creaking/Cracking - occurs as ice is being ejected from the

ice maker mold.

The doors will not close completely

• Door blocked open? Move food packages away from door.

• Bin or shelf in the way? Push bin or shelf back in the correct

position,

The doors are difficult to open

The motor seems to run too much

Your new refrigerator may run longer than your old one due to its high-efficiency compressor and fans. The unit may run even longer if the room is warm, a large food load is added, doors are opened often, or if the doors have been left open.

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

• Gaskets dirty or sticky? Clean gaskets and contact surfaces

with mild soap and warm water. Rinse and dry with soft cloth.

Temperature is too warm

• New installation? Allow 24 hours following installation for the refrigerator to cool completely.

• Door(s) opened often or left open? Allows warm air to enter refrigerator. Minimize door openings and keep doors fully

closed,

• Large load of food added? Allow several hours for refrigerator to return to normal temperature.

• Controls set correctly for the surrounding conditions? Adjust the controls a setting colder. Check temperature in 24 hours. See "Using the Controls."

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

• Humid room? Contributes to moisture buildup.

• Door(s) opened often or left open? Allows humid air to enter refrigerator. Minimize door openings and keep doors fully closed.

Water filter installed on the refrigerator? Remove filter and operate ice maker. If ice quality improves, then the filter may be clogged or incorrectly installed, Replace filter or reinstall it correctly.

• Reverse osmosis water filtration system connected to your cold water supply? This can decrease water pressure. See "Water Supply Requirements,"

• Questions remain regarding water pressure? Call a licensed, qualified plumber.

Off-taste, odor or gray color in the ice

• New plumbing connections? New plumbing connections can cause discolored or off-flavored ice,

• Ice stored too long? Discard ice. Wash ice bin. Allow 24 hours for ice maker to make new ice.

• Odor transfer from food? Use airtight, moisture proof packaging to store food,

• Are there minerals (such as sulfur) in the water? A water filter may need to be installed to remove the minerals.

Water filter installed on the refrigerator? Gray or dark discoloration in ice indicates that the water filtration system needs additional flushing, Flush the water system before using a new water filter. Replace water filter when indicated. See "Water Filtration System."

The ice maker is not producing ice or not enough ice

• Refrigerator connected to a water supply and the supply shutoff valve turned on? Connect refrigerator to water supply and turn water shutoff valve fully open.

• Kink in the water source line? A kink in the line can reduce water flow, Straighten the water source line.

• Ice maker turned on? Make sure wire shutoff arm or switch (depending on model) is in the ON position.

• New installation? Wait 24 hours after ice maker installation for ice production to begin. Wait 72 hours for full ice

production.

• Freezer door closed completely? Firmly close the freezer compartment door. Ifthe freezer compartment door will net close all the way, see "The doors will not close completely,"

• Large amount of ice recently removed? Allow 24 hours for ice maker to produce more ice.

• Ice cube jammed in the ice maker ejector arm? Remove ice from the ejector arm with a plastic utensil.

Water filter installed on the refrigerator? Remove filter and operate ice maker. If ice volume improves, then the filter may be clogged or incorrectly installed, Replace filter or reinstall it correctly,

• Reverse osmosis water filtration system connected to your cold water supply? This can decrease water pressure, See "Water Supply Requirements,"

The water dispenser will not operate properly

• Refrigerator connected to a water supply and the supply shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

• Kink in the water source line? Straighten the water source line.

• New installation? Flush and fill the water system, See "Water Dispenser."

• Is the water pressure at least 35 psi (241 kPa)? The water pressure to the home determines the flow from the dispenser.

See "Water Supply Requirements," Water filter installed on the refrigerator? Remove filter and

operate dispenser. If water flow increases, the filter may be clogged or incorrectly installed, Replace filter or reinstall it

correctly,

• Refrigerator door closed completely? Close the door firmly. If it does not close completely, see "The doors will not

close completely."

• Recently removed the doors? Make sure the water dispenser wire/tube assembly has been properly

reconnected. See "Refrigerator Doors,"

• Reverse osmosis water filtration system connected to your cold water supply? This can decrease water pressure.

See "Water Supply Requirements,"

Water is leaking from the dispenser system

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

• Water shutoff valve not fully open? Turn the water shutoff valve fully open.

• Kink in the water source line? A kink in the line can reduce water flow, Straighten the water source line.

NOTE: One or two drops of water after dispensing is normal.

• Glass not being held under the dispenser long enough? Hold the glass under the dispenser 2 to 3 seconds after releasing the dispenser lever.

• New installation? Flush the water system, See "Water Dispenser."

• Recently changed water filter? Flush the water system. See "Water Dispenser."

• Water on the floor near the base grille? Make sure the water dispenser tube connections are fully tightened. See "Refrigerator Doors."

Water from the dispenser is warm

NOTE: Water from the dispenser is only chilled to 50°F (10°C).

• New installation? Allow 24 hours after installation for the water supply to cool completely.

Recently dispensed large amount of water? Allow 24 hours for water supply to cool completely.

Water not been recently dispensed? The first glass of water

may not be cool. Discard the first glass of water. Refrigerator connected to a cold water pipe? Make sure

the refrigerator is connected to a cold water pipe. See "Water Supply Requirements."

PROTECTION AGREEMENTS

Master Protection Agreements

Congratulations on making a smart purchase. Your new Kenmore ®product is designed and manufactured for years of dependable operation. But like all products, it may require preventive maintenance or repair from time to time. That's when having a Master Protection Agreement can save you money and aggravation.

The Master Protection Agreement also helps extend the life of your new product. Here's what the Agreement* includes:

v' Parts and labor needed to help keep products operating

properly under normal use, not just defects. Our coverage goes well beyond the product warranty. No deductibles, no functional failure excluded from coverage-- real protection.

v' Expert service by a force of more than 10,000 authorized

Sears service technicians, which means someone you can trust will be working on your product.

v' Unlimited service calls and nationwide service, as often as

you want us, whenever you want us.

v' "No-lemon" guarantee - replacement of your covered

product if four or more product failures occur within twelve months.

v' Product replacement if your covered product can't be fixed. v' Annual Preventive Maintenance Check at your request - no

extra charge.

v' Fast help by phone - we call it Rapid Resolution - phone

support from a Sears representative on all products. Think of us as a "talking owner's manual."

v' Power surge protection against electrical damage due to

power fluctuations.

v' $250 Food Loss Protection annually for any food spoilage

that is the result of mechanical failure of any covered refrigerator or freezer.

v' Rental reimbursement if repair of your covered product takes

longer than promised.

v' 10% discount off the regular price of any non-covered repair

service and related installed parts.

Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime day or night, or schedule a service appointment online.

The Master Protection Agreement is a risk free purchase. If you cancel for any reason during the product warranty period, we will provide a full refund. Or, a prorated refund anytime after the product warranty period expires. Purchase your Master Protection Agreement today!

Some limitations and exclusions apply. For prices and

additional information in the U.S.A. call 1-800-827-6655. *Coverage in Canada varies on some items. For full details

call Sears Canada at 1-800-361-6665.

Sears Installation Service For Sears professional installation of home appliances, garage

door openers, water heaters, and other major home items, in the U.S.A. or Canada call 1-800-4-MY-HOME ®.

ACCESSORIES

Replacement Parts:

To order stainless steel cleaner or replacement filters, call 1-800-4-MY-HOME ®and ask for the appropriate part number listed below or contact your authorized Kenmore dealer.

Stainless Steel Cleaner & Polish: Order Part #D22 M40083 R

Replacement Filter:

Order Part #469006-750

WATER FILTER

CERTIFICATIONS

Statc uf Cahfom_a

Department of Hcatth Services

Water Treatment Device

Certificate Number

03- 1583

Da(e ]_stlcd: Sepler, lix.r 16, 20(})

Ika_e R_._l_e_l A,,rll 2? "(X)4

Trademark/Model DesionaTion

UKFS001 AXX750

,169006-750

67OO35?3-75

Manufacturer: PenluPu_e If,,

turbidity

Orqanie Contammams

Rated Service Capactty: 750 gal Rated Serv+ce Flow: 0 78 gpm

Do no_ u_, _bere _alcr is m,cmb*ol_g_eally u_k' or with waler _f u_k_w_ quah_y, except that _s(em_ cemfied e_( reduc_lo_ may bc usvd oft dlsm_c_d _alers _hat r_y ctm_am ht_rab)¢ cy_t_

Conditions of Certification:

Deplacement Elements

[JKFS_ IAXX

PRODUCT DATA SHEETS

Interior Water Filtration System

Model 469006-750 Capacity 750 Gallons (2839 Liters)

System tested and certified by NSF International against NSF/ANSI

Class I*; and against NSF/ANSl Standard 53 for the reduction of Lead, Standard 42 for the reduction of Chlorine Taste and Odor, Particulate

Mercury, Atrazine, Benzene, p-Dichlorobenzene, Carbofuran,

Toxaphene, Cysts, Turbidity, Asbestos and Lindane.

This system has been tested according to NSF/ANSl Standards 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSl Standards 42 and 53.

Substance Reduction NSF Reduction Average Influent Challenge Maximum Average Minimum% Average% Aesthetic Effects Requirements Influent Concentration Effluent Effluent Reduction Reduction

Chlorine Taste/Odor 50% reduction 1.88 mg/L 2.0 mg/L _+10% 0.06 mg/L 0.05 mg/L 96.84 >97.26

Particulate Class I* 5,700,000 #/mL

Contaminant NSF Reduction Average Influent Challenge Maximum Average Minimum% Average%

Reduction Requirements Influent Concentration Effluent Effluent Reduction Reduction

Lead: @ pH 6.5 0.010 mg/L 0.153 mg/L _ 0.15 mg/L _+10% < O.O01mg/L < O.0Olmg/L >99.29% >99.35% Lead: @ pH 8.5 0.010 mg/L 0.150 mg/L t 0.15 mg/L _+10% < 0.001mg/L < 0.001mg/L >99.29% >99.33%

Mercury: @ pH 6.5 0.002 mg/L 0.006 mg/L 0.006 mg/L _+10% 0.0005 mg/L 0.0003 mg/L 90.91 95.70 Mercury: @ pH 8.5 0.002 mg/L 0.006 mg/L 0.006 mg/L _+10% 0.0015 mg/L 0.0008 mg/L 75.93 86.22

Benzene 0.005 mg/L 0.014 mg/L 0.015 mg/L _+10% 0.0011 mg/L 0.0006 mg/L 92.14% 95.71% p-Dichlorobenzene 0.075 mg/L 0.208 mg/L 0.225 mg/L _+10% < 0.0005 mg/L < 0.0005 mg/L 99.74% 99.76%

Carbofuran 0.04 mg/L 0.081 mg/L 0.08 mg/L _+10% < 0.001mg/L < 0.001mg/L 98.46% 98.74% Toxaphene 0.003 mg/L 0.015 mg/L 0.015 _+10% < 0.001mg/L < 0.001mg/L 91.67% 92.97%

Atrazine 0.003 mg/L 0.009mg/L 0.009 mg/L _+10% < 0.002 mg/L < 0.002 mg/L 75.31% 76.99% Asbestos 99% 155 MF/L 107to 108fibers/L t_ <1 MF/L <1 MF/L >99.99% >99.99%

Live Cysts _ >99.95% 166,500 #/L 50,000/L min. <1 #/L; <1 #/L _ >99.99 >99.99

Turbidity 0.5 NTU 10.7 NTU 11 _+1 NTU 0.49 NTU 0.31 NTU 95.2 97.09

Lindane 0.0002 mg/L 0.002 mg/L 0.002 _+10% < 0.0001 mg/L 0.000 mg/L 96.50% 98.72%

85% reduction At least 10,000 69,000 #/mL** 30,583 #/mL 98.94 99.52

particles/mL

Test Parameters: pH = 7.5 + 0.5 unless otherwise noted. Flow = 0.78 gpm (1.9 Lpm). Pressure

71.6°F (20°C to 22°C).

• It is essential that operational, maintenance, and filter replacement requirements be carried out for the product to

• Refer to the "Warranty" section for the Manufacturer's limited warranty.

perform as advertised.

• The filter monitor system measures the amount of water that passes through the filter and alerts you to replace the filter.

When 90% of the filter's rated life is used, the yellow (Order) light comes on. When 100% of the filter's rated life is used, the red (Replace) light comes on, and it is recommended that you replace the filter. For models without filter status lights,

Application Guidelines/Water Supply Parameters

Water Supply City or Well Water Pressure 35 - 120 psi (241 - 827 kPa) Water Temperature 33 ° - 100°F (1° - 38°C) Service Flow Rate 0.78 gpm (2.9 L/min.) @ 60 psi

replace the filter every 6 months. Use replacement filter model 469006-750. 2007 suggested retail price of

$49.99 U.S.A./S65.95 Canada. Prices are subject to change without notice.

• The product is for cold water use only.

• Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

• Refer to the "Water Filtration System" section for the Manufacturer's name and telephone number.

*Class Iparticle size: >0.5 to <1 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

fThese contaminants are not necessarily in your water supply. Performance may vary based on local water conditions.

ttFibers greater than 10 um in length

*Based on the use of Cryptosporidium parvum oocysts

® NSF is a registered trademark of NSF International.

= 60 psig (413.7 kPa). Temp. = 68°F to

+ 47 hidden pages