Kenmore Elite 10674202400, 10674202401, 10674202402, 10674203400, 10674203401 Owner’s Manual

...

E L ! T E

Top-Mount Refrigerator

Refrigerador con montaje superior

R_frig_rateur superpos_

................ =.= _.._ _.._;, ._¢,._,;, _,,._°° IUI ¢=I IkI_;;;;;i_iI;>;;ll

Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com

2300951 Sears Canada Inc., Toronto, Ontario, Canada MSB 2B8 www.sears.ca

TABLEOF CONTENTS

WARRANTY

WARRANTY ..................................................................................... 2

REFRIGERATOR SAFETY .............................................................. 3

Proper Disposal of Your Old Refrigerator .................................... 3

INSTALLATION INSTRUCTIONS .................................................. 4

Unpack the Refrigerator ............................................................... 4

Location Requirements ................................................................ 4

Electrical Requirements ................................................................ 5

Water Supply Requirements ........................................................ 5

Connect the Water Supply ........................................................... 5

Refrigerator Doors - Contour ....................................................... 7

Adjust the Doors ........................................................................ 10

Prepare the Water System ........................................................ 10

Normal Sounds .......................................................................... 10

REFRIGERATOR USE ................................................................. 11

Ensuring Proper Air Circulation ................................................. 11

Using the Controls ..................................................................... 11

Water Dispenser ........................................................................ 12

Water Filter Status Light ............................................................ 14

Water Filtration System ............................................................. 14

Ice Maker ................................................................................... 14

REFRIGERATOR FEATURES ..................................................... 15

Refrigerator Shelves .................................................................. 15

Crispers and Meat Drawers ...................................................... 15

Crisper Humidity Control ........................................................... 16

Chilled Meat Drawer .................................................................. 16

Wine or Can/Bottle Rack ........................................................... 16

Utility or Egg Bin........................................................................ 16

FREEZER FEATURES ................................................................. 17

Freezer Shelf.............................................................................. 17

Adjustable Half-width Freezer Shelf .......................................... 17

Pull-out Freezer Floor ................................................................ 17

DOOR FEATURES ....................................................................... 17

Tilt-out Freezer Basket .............................................................. 17

Snap-on Door Rails ................................................................... 18

Door Bins ................................................................................... 18

Adjustable Utility Compartment & Tray ..................................... 18

Door Chill ................................................................................... 18

REFRIGERATOR CARE ............................................................... 19

Cleaning ..................................................................................... 19

Changing the Light Bulbs .......................................................... 19

Power Interruptions ................................................................... 20

Vacation and Moving Care ........................................................ 20

TROUBLESHOOTING .................................................................. 21

PROTECTION AGREEMENTS .................................................... 23

In the U.S.A ................................................................................ 23

In Canada .................................................................................. 24

Accessories ............................................................................... 24

WATER FILTER CERTIFICATIONS ............................................ 24

PRODUCT DATA SHEETS .......................................................... 25

SERVICE NUMBERS ............................................... BACK COVER

ONE-YEAR FULL WARRANTY ON REFRIGERATOR For one year from the date of purchase, when this refrigerator is

operated and maintained according to instructions attached to or furnished with the product, Sears will repair this refrigerator, free of charge, if defective in material or workmanship.

FIVE-YEAR FULL WARRANTY ON SEALED REFRIGERATION SYSTEM

For five years from the date of purchase, when this refrigerator is operated and maintained according to owner's instructions attached to or furnished with the product, Sears will repair the sealed system (consisting of refrigeration, connecting tubing, and compressor), free of charge, if defective in materials or workmanship.

The above warranty coverage applies only to refrigerators which are used for storage of food for private household purposes and excludes original and replacement Kenmore Filtered Ice & Water filter cartridges (if equipped with the filter system). Original and replacement cartridges are warranted for 30 days, parts only, against defects in material or workmanship.

WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEAREST SEARS SERVICE CENTER IN THE UNITED STATES OR CANADA.

This warranty applies only while this product is in use in the United States or Canada. This warranty gives you specific legal rights, and you may also have other rights which vary

from state to state or province to province. Warranty terms may vary in Canada. Contact your local Sears

Service Center for complete details.

Sears, Roebuck and Co.

Dept. 817WA, Hoffman Estates, IL 60179

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2B8

Product Record

In the space below, record your complete model number, serial number, and purchase date. You can find this information on the

model and serial number label located on the inside wall of the refrigerator compartment.

Have this information available to help you obtain assistance or service more quickly whenever you contact Sears concerning your refrigerator.

Model number 106.

Serial number

Purchase date

Save these instructions and your sales receipt for future reference.

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately follow instructions,

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet,

• Do not remove ground prong.

• Do not use an adapter,

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all panels before operating.

• Remove doors from your old refrigerator.

SAVE THESE INSTRUCTIONS

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline, away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker

kit ready models only).

• Use a sturdy glass when dispensing ice or water (on some models).

Proper Disposal of Your Old Refrigerator

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Take off the doors,

• Leave the shelves in place so that children may not easily climb inside.

INSTALLATION INSTRUCTIONS

Remove the Packaging

Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see "Refrigerator Safety."

On some models, shelves, bins, door shelf rails, and other feature parts may be packaged in the Interior FeaturePak.

Follow the instructions contained in the package for proper assembly.

• There are 4 bolts that secure the refrigerator to the shipping case. Keep these bolts because they are the refrigerator's leveling legs.

• Properly dispose of packaging.

IMPORTANT: Do not remove the white foam air return insert that is located behind the control panel on the ceiling of the

refrigerator (on some models). The insert is part of the refrigerator and not part of the packing material. If the insert is removed, ice may migrate down from the freezer and cause icicles to form.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to protect the floor. Always pull the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move it, as floor damage could occur.

Clean Before Using

After you remove all of the package materials, clean the inside of your refrigerator before using it. See the cleaning instructions in "Refrigerator Care."

Important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when removing them to avoid impact from dropping.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

Toensure proper ventilation for your refrigerator, allow for a V2" (1.25 cm) space on each side and at the top. When installing your

refrigerator next to a fixed wall, leave 2" (5.08 cm) minimum clearance on each side (some models require more) to allow for the door to swing open. If your refrigerator has an ice maker,

allow extra space at the back for the water line connections. NOTE: Do not install the refrigerator near an oven, radiator, or

other heat source, nor in a location where the temperature will fall below 55°F (13°C).

L JL

II I

2" Is.oecm)/

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an

extension cord. NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting.

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

IMPORTANT:

• If you turn the refrigerator on before the water line is connected, turn the ice maker OFR

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.

TOOLS NEEDED: Flat-blade screwdriver, Z/le"and 1/2"open-end wrenches or two adjustable wrenches, 1/4"nut driver and drill bit, hand drill or electric drill (properly grounded).

NOTE: Your refrigerator dealer has a kit available with a V4" (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or 3/_6" (4.76 mm) saddle valve which reduces water flow and clogs more easily.

Wa_rPmssum

A cold water supply with water pressure of between 30 and 120 psi (207 - 827 kPa) is required to operate the water dispenser

and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 - 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 - 414 kPa). If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 - 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

If your refrigerator has a water filter cartridge, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter cartridge. See "Water Filtration System."

If you have questions about your water pressure, call a licensed, qualified plumber.

Read aft directions before you begin. iMPORTANT: If you turn the refrigerator on before the water line

is connected, turn the ice maker OFE

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Locate a 1_,,to 11/4"(1.25 cm to 3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use V4"

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a grounded drill, drill a V4"hole in the cold water pipe you have selected.

......... HH

A. Cold water pipe B. Pipe clamp C. Copper tubing D. Compression nut

E. Compression sleeve

Shutoff valve

G. Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the V4"drilled hole

in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws

carefully and evenly so washer makes a water[ight seal. Do not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut onto the copper tubing as shown. Inser[ the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is

clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove the shipping tape from the gray, coiled water tubing on the rear of the refrigerator.

3. A 1/4"x V4"coupling is needed in order to connect the water tubing to an existing household water line. Thread the

provided nut onto the coupling on the end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten.

Style 1

1. Unplug refrigerator or disconnect power.

2. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do

not overtighten.

3. Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help prevent

damage to the tubing when the refrigerator is pushed back against the wall.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

C D

A, Tube clamp

B, Copper tubing

6. The ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the V4"(6.36 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

7. Plug in refrigerator or reconnect power.

8. Flush the water system. See "Prepare the Water System."

NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill ice container.

C. Compression nut D. Valve inlet

A B C D E F

A Refrigerator water tubing D Coupling (provided) B Nut (provided) E.Ferrule (purchased)

C Bulb _ Nut (purchased)

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

6. Plug in refrigerator or reconnect power.

7. Flush the water system. See "Prepare the Water System."

NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to

completely fill ice container.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

3. Thread the provided nut onto the water valve as shown. NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

A. Bulb

B.Nut (provided)

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

6. Plug in refrigerator or reconnect power.

7. Flush the water system. See "Prepare the Water System."

NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill ice container.

TOOLS NEEDED: 5/_6"hex-head socket wrench, #2 Phillips screwdriver, flat-blade screwdriver, 5/_e"open-end wrench, flat 2" putty knife.

IMPORTANT:

• Unplug refrigerator or disconnect power.

• Turn off the water supply to the refrigerator. If there is water in the dispenser's water line, some spilling may occur during door swing reversal.

• Remove food and any adjustable door or utility bins from doors.

• If you only want to remove and replace the doors, see "Remove Doors and Hinges" and "Replace Doors and Hinges."

• All graphics referenced in the following instructions are included later in this section after "Final Steps."

Remove Doors and Hinges

_8" Hex-head hinge screw

1. Unplug refrigerator or disconnect power.

2. Turn off the water supply to the refrigerator.

3. Open the refrigerator door and remove the base grille from the bottom front of the refrigerator. See Graphic 1.

4. Close the refrigerator door and keep beth deors closed until you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the doors while the hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working.

5. Pull the water dispenser wire/tube assembly out of the channel on the bottom of the refrigerator door. See Graphic 2.

6. Disconnect the wiring plug. See Graphic 3.

7. Disconnect the water dispenser tubing. Press the red outer ring against the face of the fitting and pull the dispenser tubing free. See Graphic 11.

NOTE: There may be water in the dispenser tubing if the dispenser has been used.

8. Remove the parts for the top hinge. See Graphic 4. Lift the freezer door free from the cabinet.

9. Remove the 5/_e"hex-head screw from the center rail. Loosen the two screws on the side just enough to remove the center

hinge. Remove the center hinge. Replace the center rail screw. See Graphic 5.

10. Lift the refrigerator door free from the cabinet.

11. Remove the parts for the bottom hinge. See Graphic 6.

Reverse Doors (optional)

IMPORTANT:

• If you want to reverse your doors so that they open in the opposite direction, follow these steps. If you are not reversing

the doors, see "Replace Doors and Hinges."

• The the graphics shown are for a right-hand swing refrigerator (hinges factory installed on the right).

Round-Head Door Handle DoorHinge

Handle Screw Screw Hole Plug Hole Plug

Right-Hand Swing to Left-Hand Swing If the door hinges were factory installed on the right-hand side of

the refrigerator, follow these steps.

1. Remove cabinet hinge hole plugs from the cabinet top and move them to opposite side hinge holes. See Graphic 7.

2. Remove door hinge hole plug from top of freezer door. Move to opposite side as shown. See Graphic 8.

3. Remove door stop from both the freezer and refrigerator doors and place them on the opposite side. See Graphic 9.

4. On the bottom of the refrigerator door, move the wire/tube assembly so the connector points toward the opposite (bottom-hinge) side. See Graphic 2.

5. Locate the water dispenser wire/tube assembly behind the left-hand side of the bottom rail. Break the tape and pull the loose end out from the bottom rail. See Graphic 10.

6. Unscrew the hose clip from the right-hand side of the bottom rail and remove it. Replace the hose clip (with the tab pointing down) on the left-hand side wire/tube assembly. See Graphic 12.

IMPORTANT: Do not completely tighten the hose clip to the bottom rail at this time.

7. Connect the right-hand side dispenser wire/tube assembly to the connectors located near the right-hand side of the water filter. Push the connectors and wire/tube assembly behind the bottom rail. See Graphic 10.

8. Go to "Replace Doors and Hinges."

Left-Hand Swing to Right-Hand Swing

If the refrigerator doors have already been reversed to left-hand swing and you wish to change back to a right-hand swing, follow

these steps.

1. Remove cabinet hinge hole plugs from the cabinet top and move them to opposite side hinge holes. See Graphic 7.

2. Remove door hinge hole plug from top of freezer door. Move to opposite side as shown. See Graphic 8.

3. Remove door stop from both the freezer and refrigerator doors and place them on the opposite side. See Graphic 9.

4. On the bottom of the refrigerator door, move the wire/tube assembly so the connector points toward the opposite (bottom-hinge) side. See Graphic 2.

5. Push the left-hand side dispenser wire/tube assembly behind the bottom rail. It will not be reconnected. See Graphic 10.

6. Unscrew the hose clip from the left-hand side of the bottom rail and remove it. Replace the hose clip (with the tab pointing

down) on the right-hand side wire/tube assembly. See Graphic 12.

IMPORTANT: Do not completely tighten the hose clip to the bottom rail at this time.

7. Disconnect the dispenser tubing and wiring plug from the connectors located near the right-hand side of the water filter.

Push the wiring plug and connector tube behind the bottom rail. They will not be reconnected. The wire/tube assembly

will reconnect later with the door. See Graphic 11.

8. Go to "Replace Doors and Hinges."

Replace Doors and Hinges 3.

___ 4.

NOTE: Graphics and steps may be reversed if the door swing is

reversed.

1. Assemble the parts for the bottom hinge as shown. Tighten all screws. See Graphic 6.

2. Replace the refrigerator door. NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working.

3. Remove the 5/16"hex-head screw from the center rail. Loosen the two screws on the side just enough to replace the center

hinge. Replace the center hinge and center rail screw. Tighten all screws. See Graphic 5.

4. Reconnect the wiring plug. See Graphic 3.

5. Reconnect the water dispenser tubing by pushing the tubing into the fitting until it stops and the black mark touches the

face of the red outer ring. See Graphic 11.

6. Carefully push the wire/tube assembly into the clips on the bottom of the refrigerator door. See Graphic 2.

7. Replace the freezer door.

8. Assemble the parts for the top hinge as shown. Do not tighten completely. See Graphic 4.

9. Line up the doors so that the bottom of the freezer door aligns evenly with the top of the refrigerator door. Tighten all

screws.

10. Open the refrigerator door a full 120 °, Locate the black electrical tape on the wire/tube assembly. Make sure the hose clip is covering the tape and tighten the hose clip completely.

See Graphic 12.

Final Steps

Check all holes to make sure that hole plugs and screws are in place. Reinstall top hinge cover. See Graphic 4.

If the door swing is reversed, remove the bottom hinge cover from the left-hand side of the base grille and replace it on the

opposite side. Replace the base grille. See Graphic 1. Plug in refrigerator or reconnect power. Turn on the water supply to the refrigerator.

NOTE: Make sure the water dispenser tube connections, at the bottom of the refrigerator door, are fully tightened.

5. Flush the water system. See "Water Filtration System."

6. If the dispenser light is not working, recheck the wiring plug connection.

Return all removable door parts to doors and food to refrigerator.

Base Grille

A. Bottom Hinge Cover

A. Wiring Plug

I I

A. Cabinet Hinge Hole Plugs

.4 ........................_

A. Door Hinge Hole Plug

Top Hinge

.......................... A

A. TopHinge Cover

B. 5/,_" Hex-Head Hinge Screws C. Top Hinge

Center Hinge

A. 5/_,, Hex-Head Hinge Screws

B. Center Hinge

Bottom Hinge

Front View

"_ A. Door Stop

B. Door Stop Screw

[]

A. Bottom Hinge

B _/_6"Hex-Head Hinge Screws

A. Right Wire/Tube B. Left Wire/Tube

A. Red Outer Ring

A. Hose Clip

Door Closing

Your refrigerator has two front adjustable rollers - one on the right and one on the left. If your refrigerator seems unsteady or you want the doors to close easier, adjust the refrigerator's tilt using

the instructions below:

Plug into a grounded 3 prong outlet. 2.

Move the refrigerator into its final location.

Remove the base grille. See Base Grille graphic. The two leveling screws are part of the front roller assemblies which are at the base of the refrigerator on either side.

Use a screwdriver to adjust the leveling screws. Turn the leveling screw to the right to raise that side of the refrigerator or turn the leveling screw to the left to lower that side. It may take several turns of the leveling screws to adjust the tilt of 3. the refrigerator.

NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws and rollers. This makes it easier to adjust the screws.

NOTES:

• If your model has a base grille filter system, make sure the base grille filter is properly installed and the cap is in the

horizontal position.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain

filterable cysts.

Use a sturdy container to depress the water dispenser until the water begins to flow. Flush the water system by

dispensing and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the system will take approximately 5 minutes and

will help clear air from the line. Additional flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of the dispenser.

Turn on the ice maker by opening the freezer door and lowering the wire shutoff arm as shown. Please refer to the

"Ice Maker" section for further instructions on the operation of your ice maker.

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced.

• Depending on your model, you may want to select the

maximum ice feature to increase the production of ice.

5. Open both doors again and check to make sure that they close as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws to the right. It may take several more turns, and you should turn both leveling screws the same amount.

6. Replace the base grille.

Align Doors

If the space between your doors looks uneven, you can adjust it using the instructions below:

1. Pry off the top hinge cover.

2. Loosen the top hinge screws using a 5/_e"socket or wrench.

3. Have someone hold the door in place or put a spacer between the doors while you tighten the top hinge screws.

4. Replace the top hinge cover.

Please read before using the water system. Immediately after installation, follow the steps below to make

sure that the water system is properly cleaned.

1. Turn off the ice maker by opening the freezer door and lifting up the wire shutoff arm as shown.

Your new refrigerator may make sounds that your old one didn't make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard surfaces, such as the floor, walls, and cabinets, can make the

sounds seem louder. The following describes the kinds of sounds and what may be making them.

• If your refrigerator is equipped with an ice maker, you will hear a buzzing sound when the water valve opens to fill the ice maker for each cycle.

Your refrigerator is designed to run more efficiently to keep your food items at the desired temperatures and to minimize energy usage. The high efficiency compressor and fans may cause your refrigerator to run longer than your old one. You may also hear a pulsating or high-pitched sound from the compressor or fans adjusting to optimize performance.

You may hear the evaporator fan motor circulating air through the refrigerator and freezer compartments. The fan speed may increase as you open the doors or add warm food.

Rattling noises may come from the flow of refrigerant, the water line, or items stored on top of the refrigerator.

Water dripping on the defrost heater during a defrost cycle may cause a sizzling sound.

As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your refrigerator.

Contraction and expansion of the inside walls may cause a popping noise.

You may hear air being forced over the condenser by the condenser fan.

• You may hear water running into the drain pan during the defrost cycle.

REFRIGERATOR USE

In order to ensure proper temperatures, you need to permit airflow between the refrigerator and freezer sections. As shown in the illustration, cool air from the refrigerator enters through the bottom of the freezer section and moves up. Most of the air then flows through the freezer section vents and recirculates under the freezer floor. The rest of the air enters the refrigerator section through the top vent and flows down the back of the refrigerator compartment. This air is then evenly distributed throughout the refrigerator compartment through the eight vents.

Do not block any of these vents with food packages. If the vents are blocked, airflow will be prevented and temperature and

moisture problems may occur. IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To prevent odor transfer and drying out of food, wrap or cover foods tightly.

To Turn the Refrigerator Power On/Off and View Set Points:

• Press and hold ON/OFF for 2 seconds to turn on/off the digital control panel and the refrigerator cooling.

IMPORTANT: Pressing the power on/off button, while in the power on mode, turns off the display and product cooling.

NOTE: If the freezer set point is below zero, the indicator light next to the freezer display will light up.

Cow FREEZER REFRIGERATOR CoW

COLDER COLDER

To View the Celsius Set Points:

• Press the °C SELECT touch pad. The indicator will light up.

Adjusting Digital Controls _

DTo Adjust Set Point Temperatures:

• Press the refrigerator or freezer up or down arrow until the desired temperature is reached.

NOTE: Wait at least 24 hours between adjustments and then recheck the temperatures before other adjustments are

made.

REFRIBERATOR COrn

IMPORTANT:

• The Refrigerator control adjusts the refrigerator compartment temperature. The Freezer control adjusts the freezer compartment temperature.

• Wait 24 hours after you turn on the refrigerator before you put food into it. If you add food before the refrigerator has cooled completely, your food may spoil. Adjusting the Refrigerator and Freezer controls to a lower (colder) setting will not cool the compartments any faster.

• If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked, before adjusting the controls.

• The preset settings should be correct for normal household usage. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.

Digital Controls

For your convenience, your controls are preset at the factory. When installing your refrigerator, make sure that the controls are still preset to the "set points" as shown.

IMPORTANT:

• The display in the power on mode indicates the freezer and refrigerator set points.

• The factory recommended set points are 0°F (-18°C) for the freezer and 37°F (3°C) for the refrigerator.

COLDER

• The set point range for the freezer is -5°F to 5°F (-21 °C to

-15°C) and 33°F to 45°F (1°C to 7°C) for the refrigerator.

CONDITION/REASON: TEMPERATURE

ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR

- Not set correctly for your Control 1° higher conditions

REFRIGERATOR too warm REFRIGERATOR

- High use or room very warm Control 1° lower FREEZER too cold FREEZER Control 1°

- Not set correctly for your higher conditions

FREEZER too warm/too little ice FREEZER Control 1°

- High use or heavy ice use lower

Additional Digital Control Panel Features

Additional features are located on the control panel at the top of the refrigerator compartment.

GrocerySavor TM

The GrocerySavor TM feature assists with periods of high refrigerator use, full grocery loads, or temporarily warm room

temperatures.

• Press GROCERY SAVORTM to set the temperatures to the lowest temperature for the freezer and for the refrigerator. The

GrocerySavor TM indicator light will remain on for 24 hours unless manually turned oft.

NOTE: The temperature display will not change. After 24 hours, the refrigerator and freezer compartments return to the previous temperature set points.

Acceler Ice 3x_Production This feature assists with temporary periods of heavy ice use by

increasing ice production.

• Press the Acceler Ice_i touch pad to turn on the feature. The accelerated ice setting will remain on until manually turned

off. NOTE: When the Acceler Ice_ifeature is on, the freezer

temperature will cool to the lowest temperature. When the ice storage bin is full, the freezer temperature will return to the

normal set point.

Cut Hazard

Use a sturdy glass when dispensing ice or water. Failure to do so can result in cuts.

IMPORTANT:

If you did not flush the water system when the refrigerator was first installed, press the water dispenser paddle with a glass or jar until you draw and discard 2 to 3 gal. (8 to 12 L) or approximately 5 minutes of water after water begins dispensing. It will take 3 to 4 minutes for the water to begin dispensing. The water you draw and discard cleans the system and helps clear air from the lines. Allow several hours for the refrigerator to cool down and chill water.

NOTE: After 4 minutes of continuous dispensing, the dispenser will stop dispensing to avoid flooding. To continue dispensing, remove the glass and press the dispensing paddle again.

When the refrigerator compartment door is open, the dispenser will not dispense water and the dispenser control panel will not display or receive input. The previous settings

will be retained.

Control Lockout

This feature will disable the control touch pads to prevent unintentional control setting changes.

NOTE: Control lockout does not shut oft power to the refrigerator.

• To disable the controls, press and hold the LOCK touch pad for 2 seconds. To reactivate the controls, press and hold the

LOCK touch pad for 2 seconds.

Dispense Water

1. Press a sturdy glass against the paddle to start dispensing.

2. Release pressure on the paddle and be sure the water has stopped dispensing before removing the glass.

NOTE: Water may have an off-flavor if you do not use the dispenser periodically. Dispense enough water every week to maintain a fresh supply.

Remove and Replace Dispenser Paddle

The Dispenser Light

The removable paddle is designed to catch small spills and allow for easy cleaning. There is no drain in the paddle. The paddle can

be removed from the dispenser to be emptied or cleaned. IMPORTANT: Press and hold LOCK OUT for 2 seconds to

activate the dispenser lock feature before removing the dispenser paddle. See "The Dispenser Lock."

1. Press up on the dispenser paddle, as shown, to release.

2. Pull down on the dispenser paddle to remove.

3. Replace the dispenser paddle by firmly snapping it into the dispenser cover as shown.

The dispenser light turns on automatically when you press the paddle to dispense water. If you want the light to be on

continuously, press the light bulb button, located on the left-hand side of the dispenser control panel, for either ON or AUTO.

NOTE: The dispenser lights are LEDs which do not need to be changed.

ON AUTO

ON: Press the light bulb button once to turn on the dispenser

light. The green indicator will appear below ON. AUTO: Press the light bulb button a second time to select the

auto mode. The green indicator will appear below AUTO. The dispenser light will automatically adjust to become brighter as the

room brightens, dimmer as the room darkens. OFF: Press the light bulb button a third time to turn the dispenser

light off.

The Dispenser Lock

The water dispenser can be locked for easy cleaning or to prevent unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the product, to the ice maker, or to the dispenser light. It simply deactivates the dispenser paddle.

To Lock the Dispenser: Press and hold the LOCK OUT button for 2 seconds until the red

indicator appears. The water dispenser and the dispenser control panel will not work.

To Unlock the Dispenser: Press and hold the LOCK OUT button for 2 seconds until the

indicator disappears. Then continue to dispense water as usual.

LOCKOUT

The water filter status light will help you know when to change your water filter cartridge. The light will change from green to yellow. This tells you that it is almost time to change the water filter cartridge. It is recommended that you replace the base grille water filter cartridge when the water filter indicator light changes to red OR water flow to your water dispenser or ice maker decreases noticeably. To change the base grille water filter cartridge, see "Water Filtration System."

After changing the water filter cartridge, reset the water filter status light.

Style 1

Press the light switch 5 times within 10 seconds. The status light will change from red to green.

(_ .................... g

A Status Light B. Light Switch

Style 2

Press and hold the water filter reset button for 2 seconds until the status light turns green. Your reset button is located on the

control panel in the refrigerator compartment.

WAFERFILTERSTA'flJS

GOOD

• REPI_CE_

NOTE: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

4. Slide the cap (removed in Step 2) onto the new filter. See illustration in Step 2.

5. With the cap in the vertical position, push the new filter into the base grille until it stops. Rotate the cap clockwise to a

horizontal position. Flush the water system. See "Flushing the Water System After Replacing Filter."

[

Flushing the Water System After Replacing Filter

Use a sturdy container to depress the water dispenser bar until the water begins to flow. Flush the water system by dispensing and discarding 2 to 3 gal. (8 to 12 L) of water. Flushing the system will take approximately 5 minutes and will help clear air from the line. Additional flushing may be required in some households.

NOTE: After 4 minutes of continuous dispensing, the dispenser will stop dispensing to avoid flooding. To continue dispensing, remove the glass and press the dispensing paddle again. As air is cleared from the system, water may spurt out of the dispenser.

Using the Dispenser Without the Water Filter

You can run the dispenser without a water filter. Your water will not be filtered.

1. Remove the base grille water filter.

2. Slide the cap off the end of the filter.

IMPORTANT: Do not discard the cap. It is part of your refrigerator. Keep the cap to use with the replacement filter.

3. With the cap in the vertical position, insert the cap into the base grille until it stops.

Changing the Water Filter

Locate the filter cap in the front base grille. Rotate the cap counterclockwise to a vertical position and pull the cap and

filter out through the base grille. NOTE: There will be water in the filter. Some spilling may

OCCU_

Remove the cap by sliding it off the end of the used filter. The cap will slide to the left or right.

IMPORTANT: Do not discard the cap. It is part of your refrigerator. Keep the cap to use with the replacement filter.

3. Take the new filter out of its packaging and remove the protective cover from the O-rings. Discard the protective

cover.

4. Rotate the cap to a horizontal position.

Turning the Ice Maker On/Off

NOTE: Do not force the wire shutoff arm up or down.

• To turn the ice maker on, simply lower the wire shutoff arm.

NOTE: Your ice maker has an automatic shutoff. As ice is made, the ice cubes will fill the ice storage bin and the ice

cubes will raise the wire shutoff arm to the OFF (arm up) position.

• To manually turn the ice maker off, lift the wire shutoff arm to the OFF (arm up) position and listen for the click to make sure the ice maker will not continue to operate.

Ice Production Rate

Slide-out Shelves (on some models)

• NORMAL Ice Production: The ice maker should refill the ice storage bin in 15-20 hours. If ice is not being made fast

enough, adjust the freezer control one degree colder. Wait 24 hours. If necessary, continue to adjust the freezer control

one degree at a time until you reach the coldest temperature. Wait 24 hours between each adjustment. See "Adjusting

Digital Controls."

• MAXIMUM Ice Production (on some models): The ice maker should refill the ice storage bin in 9-13 hours. If your

refrigerator has the Acceler Ice 3_ifeature, push the ACCELER ICE3_button on the control panel in the refrigerator

compartment. A green light will indicate the Acceler Ice3_i feature is on.

NOTE: When the Acceler Ice_ feature is on, the freezer temperature will cool to the lowest temperature. When the ice

storage bin is full, the freezer temperature will return to the normal set point.

Remember

• Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

• The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage paris of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.

• Do not store anything on top of the ice maker or in the ice storage bin.

REFRIGERATOR FEATURES

Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word "Accessory." Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please

call 1-800-4-MY-HOME _.

To Remove and Replace a Shelf in a Metal Frame:

1. Pull the shelf forward to the stop. Tilt the front of the shelf up

and lift it slightly as you pull the shelf from the frame.

2. Replace the shelf by guiding it back into the slots on the frame and pushing the shelf in past the stop.

Shelves and Shelf Frames

To Remove and Replace a Shelf/Frame:

1. Remove the shelf/frame by tilting it up at the front and lifting it out of the shelf supports.

2. Replace the shelf/frame by guiding the rear shelf hooks into the shelf supports. Tilt the front of the shelf up until rear shelf hooks drop into the shelf supports. Check to make sure that the shelf is securely in position.

Slide-away Shelf

For storage flexibility, the slide-away shelf slides back and down to allow you to store tall items on the front half of the shelf below.

To Make the Shelf Half-depth:

Raise up on the shelf and slide it toward the back of the refrigerator compartment until it stops.

Important information to know about glass shelves and covers:

Your model may have glass or wire shelves. Store similar foods together and adjust the shelves to fit different heights. This

reduces the time the refrigerator door is open and saves energy.

Drawers

To Remove and Replace a Drawer:

1. Slide drawer straight out to the stop. Lift the front of the drawer and slide it out the rest of the way.

2. Replace a drawer by sliding it back in fully past the stop.

Crisper Cover

To Remove the Crisper(s) Cover:

1. Remove crisper(s). Hold the glass insert firmly with one hand

and press up in the center of the glass insert until it rises above the plastic frame. Carefully slide the glass insert

forward to remove.

2. Lift the cover frame and remove it.

The chilled meat drawer temperature control is located on the left-hand side of the meat drawer cover. Slide the meat drawer

temperature control forward to make the meat drawer less cold or backward to make the drawer more cold.

To Replace the Crisper(s) Cover:. NOTE: Before reinstalling the cover, make sure the U-shaped

reinforcement bar is reinstalled in the front edge of the crisper cover.

1. Fit back of cover frame into supports on side walls of the refrigerator and lower the front of the cover frame into place.

2. Slide rear of glass insert into cover frame and lower front into place.

Meat Drawer Cover

To Remove and Replace the Meat Drawer Cover:.

1. Remove the meat drawer. Tilt up the front of the cover and lift at the back. Pull the cover straight out.

2. Replace the cover by guiding the rear hooks into the shelf supports. Tilt the cover up at the front until the rear hooks drop into the slots. Lower the front of the cover to a level position and replace the meat drawer.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and moisture-proof. Rewrap if necessary. See the following chart for

storage times. When storing meat longer than the times given, freeze the meat.

Fresh fish or shellfish ......................... use same day as purchased

Chicken, ground beef, variety meats (liver) ...................... 1-2 days

Cold cuts, steaks/roasts ................................................... 3-5 days

Cured meats ................................................................... 7-1g days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or plastic containers with tight lids.

e Rack

To Remove and Replace the Wine Rack (left) or Can/Bottle Rack (right):

1. Remove the rack by pulling it straight out from the shelf.

2. Replace the rack by sliding it in between the shelf and the wall of the refrigerator.

The Humidity Control is located on the crisper drawer. You can adjust the amount of humidity in the moisture-sealed crisper using the settings between HIGH and LOW.

LOW (open) lets moist air out of the crisper for best storage of fruits and vegetables with skins.

• Fruit: Wash, let dry and store in refrigerator in plastic bag in crisper. Do not wash or hull berries until they are ready to use. Sort and keep berries in original container in crisper.

• Vegetables with skins: Place in plastic bag or plastic container and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage of fresh, leafy vegetables.

• Leafy vegetables: Wash in cold water, drain and trim or tear oft bruised and discolored areas. Place in plastic bag or plastic container and store in crisper.

Humldlly _Htrol

moQeooQeo _w

L o' s;;;gg'" I:I

Depending on your model, you may have a one, two or three piece bin. Eggs may be stored in the egg tray or loose in the bin.

NOTE: Store eggs in a covered container for long-term storage. If your model does not have an egg storage bin, store eggs in their

original carton on an interior shelf.

FREEZER FEATURES

call 1-800-4-MY-HOME _.

To Remove and Replace the Shelf:

1. Remove the shelf by lifting the entire shelf slightly and moving it all the way to the left-hand side. Tilt the right-hand side up and out of the shelf supports.

2. Replace the shelf by inserting the left-hand end all the way into the shelf supports. Then, lower the right-hand end of the shelf and insert it into the shelf supports.

NOTE: The shelf should lower slightly and lock into place. If the shelf does not appear stable, make sure both ends of the shelf are inserted into the shelf supports.

Frozen Food Storage Guide

Storage times will vary according to the quality and type of food, the type of packaging or wrap used (should be airtight and moisture-proof), and the storage temperature. Seal the package or container securely to prevent taste and odor transfer throughout the product. Ice crystals inside a sealed package are

normal. Put no more unfrozen food into the freezer than will freeze within

24 hours (no more than 2 to 3 Ibs. of food per cubic foot [907- 1,350 g per 28 L] of freezer space). Leave enough space in the freezer for air to circulate around packages. The freezer door must close tightly. For more information on preparing food for freezing, check a freezer guide or reliable cookbook.

To Remove and Replace the Shelf:

1. Remove the shelf by lifting the shelf up and pulling straight out,

2, Replace the shelf overthe supports and lower it into place.

To Remove and Replace the Freezer Floor:

1. Lift both back "fences" up and out.

2. Remove the freezer floor by pulling it out about 1" (2.5 cm) with one hand around the air tower section (center back) and

one hand at center front.

3. Lift up floor at rear until hooks release from cabinet and pull the floor out the rest of the way.

4. Replace the freezer floor by sliding the floor straight in until the hooks drop into place at rear of cabinet.

5. Replace "fences" by aligning pins with socket in the floor, and pushing down until they snap into place.

DOOR FEATURES

call 1-800-4-MY-HOME _.

Y'Tft-o £ Bsskdt

The freezer basket tilts out for easy access to items stored in the freezer door. The freezer basket may be removed for easier

cleaning.

To Remove the Tilt-out Freezer Basket:

1. Tilt open the freezer basket.

2. Grasp the left-hand bracket. Firmly press the bracket toward the outside to pull the bracket away from the door tab.

NOTE: To keep the basket from falling, hold the basket while removing the bracket.

To Remove and Replace the Shelf Rack:

1. Remove the rack by tilting the front end up and lifting it off the full-width wire shelf.

2. Replace the rack by tilting the back side of the rack down so that it hooks around the back edge of the full-width wire shelf.

A. Bracket

3. Grasp the right-hand bracket. Firmly press the bracket toward the outside to pull the bracket away from the door

tab. NOTE: To keep the basket from falling, hold the basket while

removing the bracket.

4, Remove the basket.

To Replace the Tilt-out Freezer Basket'.

1. Snap the right-hand bracket onto the tab above the freezer

door shelf IMPORTANT: Be sure that the bracket touches the shelf and

push the bracket back until it snaps firmly into place.

2. Insert the left-hand basket post into the left-hand bracket.

A Basketpost

3. While holding the left-hand bracket in place, insert the right- hand basket post into the right-hand bracket on the freezer

door.

4. Snap the left-hand bracket onto the tab above the freezer door shelf.

IMPORTANT: Be sure that the bracket touches the shelf and push the bracket back until it snaps firmly into place.

To Remove and Replace Bins:

1. Remove the bin by lifting it and pulling it straight out.

2. Replace the bin by sliding it in above the desired support and pushing it down until it stops.

The utility compartment and tray slide from one side to the other for more flexible storage. The tray fits on either side of the utility compartment or partially underneath it. Try moving it to different positions to find the option that works best for you.

To Install and Adjust the Utility Compartment and Tray:

1o Insert the front of the utility tray into the slot on the back of

the shelf rail. Lower the back of the tray into position.

2. Place the front of the utility compartment on top of the shelf rail. Lower the back of the compartment onto the ribs on the refrigerator door.

The door chill vents are located in the refrigerator door. These vents allow cold air to flow onto items stored in the refrigerator

The door rails may be removed for easier cleaning.

door.

To Remove and Replace the Rails:

Remove the rails by pushing in slightly on the front of the [L-"___ bracket while pulling out on the inside tab. Repeat these steps for the other end of the rail.

Replace the rails by aligning the ends of the brackets with the buttons on the sides of the door liner. Firmly snap bracket and rail assembly onto the tabs above the shelf as shown.

REFRIGERATOR CARE

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to prevent

odors from building up. Wipe up spills immediately.

To Clean Your Refrigerator

1. Unplug refrigerator or disconnect power.

2. Remove all removable parts from inside, such as shelves,

crispers, etc.

3. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

• Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools. These can scratch or damage materials.

• To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs. to 1 qt. [26 g to 0.95 L] of water).

4. Determine whether your refrigerator exterior is painted metal, Ultra Satin TM (stainless look) finish, brushed aluminum or

stainless steel, and choose the appropriate cleaning method. NOTE: Ultra Satin TM (stainless look) finish has a smooth,

uniform color with a glossy finish that resists fingerprints. Stainless steel has a distinct grainy texture with variation in color that is natural to steel.

Painted metal: Wash exteriors with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive

or harsh cleaners, or cleaners designed for stainless steel. Dry thoroughly with a soft cloth. For additional protection against damage to painted metal exteriors, apply appliance

wax (or auto paste wax) with a clean, soft cloth. Do not wax plastic parts.

Brushed aluminum: Wash with a clean sponge or soff cloth and a mild detergent in warm water. Do not use abrasive or

harsh cleaners, or cleaners designed for stainless steel. Dry thoroughly with a soft cloth.

Ultra Satin TM (stainless look) finish: Wash with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners, or cleaners designed for stainless steel. Dry thoroughly with a soft cloth.

Stainless steel finish: Wash with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners. Dry thoroughly with a soft cloth.

• To keep your stainless steel refrigerator looking like new and to remove minor scuffs or marks, it is suggested that you use the manufacturer's approved Stainless Steel Cleaner & Polish. To order the cleaner, see "Accessories."

IMPORTANT: This cleaner is for stainless steel parts only!

Do not allow the Stainless Steel Cleaner & Polish to come into contact with any plastic parts such as the trim

pieces, dispenser covers or door gaskets. If accidental contact does occur, clean plastic part with a sponge and mild detergent in warm water. Dry thoroughly with a soft

cloth.

There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille. See "Base Grille" graphic or "Base Grille" section.

• Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

6. Plug in refrigerator or reconnect power.

NOTE: Not all bulbs will fit your refrigerator. Be sure to replace the bulb with one of the same size, shape, and wattage.

1. Unplug refrigerator or disconnect power.

2. Remove the bulb from behind the control panel in the refrigerator or from behind the light shield in the freezer (on some models). Replace it with a bulb of the same wattage.

3. Plug in refrigerator or reconnect power.

If the power will be out for 24 hours or less, keep the door or doors closed (depending on your model) to help food stay cold

and frozen. If the power will be out for more than 24 hours, do one of the

following:

• Remove all frozen food and store it in a frozen food locker.

• Place 2 Ibs. (907 g) of dry ice in the freezer for every cubic foot (28 L) of freezer space. This will keep the food frozen for 2 to 4 days.

• If neither a food locker nor dry ice is available, consume or can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled one. A freezer full of meat stays cold longer than a freezer full of baked goods. If you see that food contains ice crystals, it may be refrozen, although the quality and flavor may be affected. If the condition of the food is poor, dispose of it.

Vacations

If You Choose to Leave the Refrigerator On While You're Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker:

• Raise wire shutoff arm to OFF (up) position or move the

switch to the OFF (right) setting.

• Shut off water supply to the ice maker.

3. Empty the ice bin.

If You Choose to Turn the Refrigerator Off Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF (right) setting.

3. Depending on the model, turn the Thermostat Control or Refrigerator Control to OFR See "Using the Controls."

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in. This stops odor and

mold from building up.

Moving

When you are moving your refrigerator to a new home, follow these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• Disconnect the water line from the back of the

refrigerator.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF (right) setting.

2. Remove all food from the refrigerator and pack all frozen food in dry ice.

3. Emptythe ice bin.

4. Depending on the model, turn the Thermostat Control or Refrigerator Control to OFR See "Using the Controls."

5. Unplug refrigerator.

6. Empty water from the defrost pan.

7. Clean, wipe, and dry thoroughly.

8. Take out all removable parts, wrap them well, and tape them together so they don't shift and rattle during the move.

9. Depending on the model, raise the front of the refrigerator so it rolls more easily OR screw in the leveling legs so they don't

scrape the floor. See "Adjust the Doors."

10. Tape the doors closed and tape the power cord to the refrigerator cabinet.

When you get to your new home, put everything back and refer to the "Installation Instructions" section for preparation instructions.

Also, if your refrigerator has an automatic ice maker, remember to reconnect the water supply to the refrigerator.

TROUBLESHOOTING

Try the solutions suggested hers first in order to avoid the cost of an unnecessary service call.

Your refrigerator will not operate The refrigerator seems to make too much noise

• Is the power cord unplugged? Plug into a grounded 3 prong • The sounds may be normal for your refrigerator. See outlet. "Normal Sounds."

• Has a household fuse blown, or has a circuit breaker tripped? Replace the fuse or reset the circuit breaker.

• Is the Refrigerator Control turned to the OFF position? See "Using the Control(s)," depending on the model.

• Is the refrigerator defrosting? Recheck to see whether the refrigerator is operating in 30 minutes. Your refrigerator will regularly run an automatic defrost cycle.

• Is the refrigerator not cooling? For models with digital controls, turn the refrigerator off and then back on again to reset. See "Using the Controls." If this does not correct the problem, call for service.

The lights do not work

• Is the power cord unplugged? Plug into a grounded 3 prong outlet.

• Is a light bulb loose in the socket or burned out? See "Changing the Light Bulb(s)," depending on the model.

There is water in the defrost drain pan

• Is the refrigerator defrosting? The water will evaporate. It is normal for water to drip into the defrost pan.

• Is it more humid than normal? When it is humid, expect that the water in the defrost pan will take longer to evaporate.

The motor seems to run too much

• Is the room temperature hotter than normal? The motor will run longer under warm conditions. At normal room temperatures, your motor will run about 40% to 80% of the

time. Under warmer conditions, it will run even more.

• Has a large amount of food just been added to the refrigerator?. Adding a large amount of food warms the refrigerator. The motor normally will run longer to cool the refrigerator back down.

• Are the doors opened often? The motor will run longer when this occurs. Conserve energy by getting all items out at one time, keeping food organized, and closing the door as soon as possible.

• Is the control set correctly for the surrounding conditions? See "Using the Control(s)," depending on the model.

• Are the doors closed completely? Close the doors firmly. If they do not close completely, see "The doors will not close completely" later in this section.

NOTE: Your new refrigerator will run longer than your old one due to its high-efficiency motor.

The ice maker is not producing ice or not enough ice

Is the freezer door closed completely? Firmly close the freezer compartment door. If the freezer compartment door

will not close all the way, see "The doors will not close completely" later in this section.

• Has the ice maker just been installed? Wait 72 hours for full ice production to begin. Once your refrigerator is cooled, the

ice maker should produce 70-120 cubes every 24 hours.

• Is the freezer temperature cold enough to produce ice? Wait 24 hours after hookup for ice production. See "Using the Control(s)," depending on the model.

• Is the wire shutoff arm in the OFF (arm up) position? Lower the wire shutoff arm to the ON (arm down) position. See "Ice Maker."

• Is the water line shutoff valve to the refrigerator turned on? Turn on the water valve. See "Connect the Water

Supply."

Does the ice maker mold have water in it or has no ice been produced? Be sure your refrigerator has been

connected to a water supply and the supply shutoff valve is turned on. See "Connect the Water Supply."

• Is an ice cube jammed in the ejector arm? Remove the ice from the ejector arm with a plastic utensil. See "Ice Maker."

• Has a large amount of ice just been removed? Allow 24 hours for ice maker to produce more ice.

• Is the control set correctly?. If too little ice is produced, see "Using the Control(s)," depending on the model.

Is there a water filter installed on the refrigerator?. The filter may be full or incorrectly installed. Depending on your model, remove the water filter cartridge. See "Water Filtration

System." Operate the dispenser. If the water flow increases noticeably, your filter is full and needs to be replaced.

• Is a reverse osmosis water filtration system connected to your cold water supply? See "Water Supply Requirements,"

NOTE: If not due to any of the above, there may be a problem with the water line. Call for service.

Off-taste, odor or gray color in the ice Water flow from the dispenser decreases noticeably

• Are the plumbing connections new, causing discolored or off-flavored ice? Discard the first few batches of ice.

Have the ice cubes been stored too long? Throw old ice

away and make a new supply. Has food in the refrigerator been wrapped properly? See

"Refrigerator Features." Do the freezer and ice bin need to be cleaned? See

"Cleaning." Does the water contain minerals (such as sulfur)? A filter

may need to be installed to remove the minerals. Is there a water filter installed on the refrigerator?.

Gray or dark discoloration in ice indicates that the water filtration system needs additional flushing. Run additional

water through the water dispenser to flush the water filtration system more thoroughly, at least 2 to 3 gal. (8 to 12 L) or

5 minutes initially. Discard discolored ice.

The water dispenser will not operate properly

Has the water system not filled? The water system needs

to be filled the first time it is used. Use a sturdy container to depress the water dispenser until water begins to flow. Dispense and discard 2 to 3 gal. (8 to 12 L) of water. This will take approximately 5 minutes and will help clear air from the line. Additional flushing may be required in some households. See "Water Dispenser."

Is the water shutoff valve not turned on or the water line connected at the source? Be sure the water shutoff valve is

turned on and the water source is connected to the refrigerator. See "Connect the Water Supply."

Is the water shutoff valve clogged or incorrectly installed? See "Connect the Water Supply." If clogging or installation is not a problem, call for service or contact a plumber.

Is there a kink in the home water source line? If you find or suspect a kink in the water line, contact a licensed, qualified plumber.

Is there a water filter installed on the refrigerator?. The filter may be clogged or incorrectly installed. First, check the

filter installation instructions to ensure that the filter was installed correctly and is not clogged. If installation or

clogging is not a problem, call for service. Is the refrigerator door closed completely? Close the door

firmly. If it does not close completely, see "The doors will not close completely" later in this section.

Have you recently removed or reversed the doors? Make sure the water dispenser wire/tube assembly has been properly reconnected at the bottom of the refrigerator door. See "Refrigerator Doors."

Is a reverse osmosis water filtration system connected to your cold water supply? See "Water Supply Requirements."

Is there a water filter installed on the refrigerator?. The

filter may be full or incorrectly installed. Depending on your model, remove the water filter cartridge. See "Water Filtration System." Operate the dispenser. If the water flow increases

noticeably, your filter is full and needs to be replaced.

Water leaking from the dispenser system

Is the glass not being held under the water dispenser long

enough? Hold the container under the water dispenser 2 to 3 seconds after releasing the dispenser lever. Water may continue to dispense during this time.

Is the dispenser dripping between uses? The water filtration system may have air in the lines, causing water to drip. Additional flushing may help clear air from the lines. Normal dispenser use should flush air from the lines within

24 to 72 hours. Is there water on the floor near the base grille? Make sure

the water dispenser tube connections, at the bottom of the refrigerator door, are fully tightened. See "Refrigerator

Doors."

The dispenser water is not cool enough

• Has the refrigerator been newly installed? Allow 24 hours for the refrigerator to cool completely.

• Has a large amount of water been recently dispensed? Allow 24 hours for the water to cool completely.

• Has water not been recently dispensed? The first glass of water may not be cool. Discard the first glass of water.

The divider between the two compartments is warm

The warmth is probably due to normal operation of the automatic exterior moisture control.

Temperature is too warm

Are the air vents blocked in either compartment? This

prevents cold air movement between the compartments. Move objects away from the air vents. See "Ensuring Proper

Air Circulation" for air vent locations. Are the door(s) opened often? The refrigerator will warm

when this occurs. Keep the refrigerator cool by getting all items out at one time, keeping food organized, and closing the door as soon as possible.

Has a large amount of food just been added to the refrigerator or freezer?. Adding a large amount of food

warms the refrigerator. It can take several hours for the refrigerator to return to the normal temperature.

Are the controls set correctly for the surrounding conditions? See "Using the Control(s)," depending on your

model. Is the refrigerator not cooling? For models with digital

controls, turn the refrigerator off and then back on again to reset. See "Using the Control(s)." if this does not correct the problem, call for service.

There is interior moisture buildup

The doors will not close completely

• Are the air vents blocked in the refrigerator?. Remove any objects from in front of the air vents. See "Ensuring Proper Air

Circulation" for air vent locations.

• Are the door(s) opened often? Avoid humidity buildup by getting all items out at one time, keeping food organized, and

closing the door as soon as possible.

• Is the room humid? It is normal for moisture to build up inside the refrigerator when the room air is humid.

• Is the food packaged correctly? Check that all food is securely wrapped. Wipe off damp food containers before placing them in the refrigerator.

• Is the control set correctly for the surrounding conditions? See "Using the Control(s)," depending on your

model.

• Was a self-defrost cycle completed? It is normal for droplets to form after the refrigerator self-defrosts.

The doors are difficult to open

• Are the gaskets dirty or sticky?. Clean gaskets and the surface that they touch. Rub a thin coat of paraffin wax on the gaskets following cleaning.

PROTECTION AGREEMENTS

• Are food packages blocking the door open? Rearrange containers so that they fit more tightly.

• Is the ice bin out of position? Push the ice bin in all the way.

• Are the crisper cover, pans, shelves, bins, or baskets out of position? Put these items into their correct positions. See

"Refrigerator Features" for more information.

• Are the gaskets sticking? Clean gaskets and the surface that they touch. Rub a thin coat of paraffin wax on the

gaskets following cleaning.

• Does the refrigerator wobble or seem unstable? Level the refrigerator. See "Adjust the Doors."

Were the doors removed during product installation and not properly replaced? Remove and replace the doors

according to "Refrigerator Doors," or call a qualified service technician.

Master Protection Agreements

Congratulations on making a smart purchase. Your new Kenmore _"_product is designed and manufactured for years of dependable operation. But like all products, it may require preventive maintenance or repair from time to time. That's when having a Master Protection Agreement can save you money and aggravation.

Purchase a Master Protection Agreement now and protect

yourself from unexpected hassle and expense.

The Master Protection Agreement also helps extend the life of your new product. Here's what's included in the Agreement:

=/Expert service by our 12,000 professional repair specialists =/Unlimited service and no charge for parts and labor on all

covered repairs

=/"No-lemon" guarantee- replacement of your covered product

if four or more product failures occur within twelve months

=/Product replacement if your covered product can't be fixed

=/Annual Preventive Maintenance Check at your request - no

extra charge

=/Fast help by phone - phone supporf from a Sears technician

on products requiring in-home repair, plus convenient repair scheduling

=/Power surge protection against electrical damage due to

power fluctuations

=/Rental reimbursement if repair of your covered product takes

longer than promised

Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime day or night, or schedule a service appointment online.

Sears has over 12,000 professional repair specialists, who have access to over 4.5 million quality parts and accessories. That's the kind of professionalism you can count on to help prolong the life of your new purchase for years to come. Purchase your Master Protection Agreement today!

Some limitations and exclusions apply. For prices and additional information, call 1-800-827-6655.

Sears Installation Service

For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, in the

U.S.A. call 1-80O-4-MY-HOME ®.

+ 53 hidden pages