Kenmore Elite 10657862800, 10657862801, 10657863800, 10657863801, 10657864800 Owner’s Manual

...

E L I T E

Side by Side Refrigerator

Refrigerador de dos puertas

S ...._F

R6frig6rateur c6te & c6te

Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com

WlO167116A Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8 www.sears.ca

TABLEOF CONTENTS

WARRANTY ..................................................................................... 3

REFRIGERATOR SAFETY .............................................................. 4

Proper Disposal of Your Old Refrigerator .................................... 4

INSTALLATION INSTRUCTIONS .................................................. 5

Unpack the Refrigerator ............................................................... 5

Location Requirements ................................................................ 5

Electrical Requirements ................................................................ 6

Water Supply Requirements ........................................................ 6

Base Grille .................................................................................... 6

Refrigerator Doors ........................................................................ 7

Adjust the Doors ........................................................................... 8

Connect Water Supply ................................................................. 9

Prepare the Water System ........................................................ 10

Normal Sounds .......................................................................... 10

REFRIGERATOR USE ................................................................. 11

Ensuring Proper Air Circulation ................................................. 11

Using the Controls ..................................................................... 11

Water and Ice Dispensers ......................................................... 12

Water Filter Status Light ............................................................ 13

Water Filtration System ............................................................. 14

Ice Maker and Storage Bin........................................................ 15

REFRIGERATOR FEATURES ..................................................... 16

Refrigerator Shelves .................................................................. 16

Deli Bin....................................................................................... 16

Convertible Vegetable/Meat Drawer, Crisper and Covers ....... 16

Wine Rack.................................................................................. 17

Utility Bin .................................................................................... 17

FREEZER FEATURES .................................................................. 17

Freezer Shelf .............................................................................. 17

Freezer Basket or Bin ................................................................ 17

DOOR FEATURES ....................................................................... 18

Door Railsor Bins ...................................................................... 18

Door Bins ................................................................................... 18

REFRIGERATOR CARE ............................................................... 18

Cleaning ..................................................................................... 18

Changing the Light Bulbs .......................................................... 19

Power Interruptions ................................................................... 20

Vacation and Moving Care ........................................................ 20

TROUBLESHOOTING .................................................................. 21

Refrigerator Operation ............................................................... 21

Temperature and Moisture ........................................................ 22

Ice and Water ............................................................................. 22

PROTECTION AGREEMENTS .................................................... 23

ACCESSORIES ............................................................................. 24

WATER FILTER CERTIFICATIONS ............................................ 24

PERFORMANCE DATA SHEET .................................................. 25

SERVICE NUMBERS ............................................... BACK COVER

KENMORE LIMITED WARRANTY

When installed, operated and maintained according to all instructions supplied with the product, if this appliance fails due to a defect in material and workmanship within one year from the date of purchase, call 1-800-4-MY-HOME ®to arrange for free repair.

If the sealed refrigerant system is defective within five years from the purchase date, call 1-800-4-MY-HOME ®to arrange for free repair.

This warranty applies for only 90 days from the date of purchase

if this appliance is ever used for other than private family purposes.

This warranty covers only defects in material and

workmanship. Sears will NOT pay for:

1. Expendable items that can wear out from normal use,

including but not limited to filters, belts, light bulbs, and bags.

2. A service technician to instruct the user in correct product installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed, operated or maintained according to the all instructions supplied with the product.

5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose.

6. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than those recommended in all instructions supplied with the product.

7. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.

Disclaimer of implied warranties; limitation of remedies

Customer's sole and exclusive remedy under this limited warranty shall be product repair as provided herein. Implied warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law. Sears shall not be liable for incidental or consequential damages. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, or limitation on the duration of implied warranties of merchantability or fitness, so these exclusions or limitations may not apply to you.

This warranty applies only while this appliance is used inthe United States or Canada.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co.

Hoffman Estates, IL 60179

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2B8

PRODUCT RECORD

In the space below, record your complete model number, serial number, and purchase date. You can find this information on the model and serial number label located on the product.

Have this information available to help you obtain assistance or service more quickly whenever you contact Sears concerning your appliance.

Model number

Serial number

Purchase date

Save these instructions and your sales receipt for future reference.

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

SAVE THESE INSTRUCTIONS

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline, away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker kit ready models only).

• Use a sturdy glass when dispensing ice (on some models).

Proper Disposal of Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator. Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Takeoff the doors.

• Leave the shelves in place so that children may not easily climb inside.

INSTALLATION INSTRUCTIONS

< e J st@

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

• Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

• Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information see "Refrigerator Safety."

When Moving "{our Refrigerator: Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor. Always pull the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move it, as floor damage could occur.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for 1/2" (1.25 cm) space on each side and at the top. When installing your refrigerator next to a fixed wall, leave 2" (5.08 cm) minimum on each side (depending on your model) to allow for the door to swing open. Ifyour refrigerator has an ice maker, allow extra space at the back for the water line connections.

lie

1/2" 11.25 cm){ /

///

Clean Before Using

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions in "Refrigerator Care."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when removing them to avoid impact from dropping.

2" (5.08 cm}i

NOTES:

• It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source. Do not install in a location where the temperature will fall below 55°F (13°C).

• Normal minimum cabinet cut-out width required for product installation is 36" (91.44 cm). However, if the product is placed against an extended wall and the ability to remove the crisper pans is desired, an additional 18" (45.72 cm) of cabinet width is required, so a total cabinet opening width of 54" (137.16 cm)is recommended.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical

connection. Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an

extension cord. NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting. See "Using the

Controls."

Water Pressure

A cold water supply with water pressure of between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

• If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter. See "Water Filtration System."

If you have questions about your water pressure, call a licensed, qualified plumber.

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver •

• 7/le"(11.11 mm) andW'(12.7mm) open-end or two adjustable •

wrenches

NOTE: Your refrigerator dealer has a kit available with a W' (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 34e"

(4.76 mm) saddle valve which reduces water flow and clogs more easily.

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.

Y4"(6.35 mm) nut driver

Y4"(6.35 mm) drill bit Cordless drill

Remove the Base Grille:

1. Open both doors.

2. Place hands along the ends of the grille. Push in on the top of the base grille and pull up on the bottom.

NOTE: Be sure to refasten the Tech Sheet behind the base grille after cleaning.

Replace the Base Grille:

1. Open both doors.

2. Line up the grille support tabs with the metal clips.

3. Push the grille firmly to snap it into place.

_i_ _,_ _ o _ _ 's'_' _ _<_

Gatherthe required tools and parts before starting installation.

TOOLS NEEDED: 1/4"hex-head socket wrench, sad' hex-head socket wrench and a flat-blade screwdriver.

IMPORTANT: Beforeyou begin, turn the refrigerator control OFF.Unplug refrigerator or disconnect power. Removefood and any adjustable door or utility binsfrom doors. NOTE:To get your product through the doorway of your home,measure the doorway to see if you need to remove the doorhandles or

the whole doors. Seethe instructions below to remove either the door handlesor the whole doors.

I __ Electrical Shock Hazard

Top Left Hinge

Do Not Remove Screw A

Failure to do so can result in death or electrical shock.

Door Removal

Top Right Hinge

Do Not Remove Screw A

Style 1 Handle

Removal

(Optional)

A B C

A. Wiring plugs

B.Wiring clip

C.Grommets

Disconnect power before removingdoors.

Style 2 Handle

Removal (Optional)

Style 3 Handle

Removal (Optional)

Water Dispenser Tubing Connection

A. Face of fitting

Level

Bottom Hinge

Do Not Remove Screw A

Door Alignment

Front Leveling

A J'_

A. Leveling Screw

Remove the Handles (optional)

Style 1

1. Apply firm pressure with your hand on the face of trim. Slide top trim up and bottom trim down away from handle. Lift trim pieces off shoulder screws. See Graphic 1.

2. Remove handle screws and handles. See Graphic 1.

3. Move refrigerator into place. Replace handles as shown. See Graphic 1.

Styles 2 and 3

1. Apply firm pressure on the handle to slide it up and off of the shoulder screws. See Graphic 1.

2. Move refrigerator into place. Replace handles as shown. See Graphic 1.

Remove the Doors

Electrical Shock Hazard

Disconnect power before removing doors. Failure to do so can result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Open both refrigerator doors. Remove the base grille by pulling up on the bottom outside corners. See Graphic 2.

3. Disconnect the water dispenser tubing located behind the base grille on the freezer door side. See Graphic 3.

• Press blue outer ring against the face of fitting and pull

the dispenser tubing free. NOTE: Keep the water tubing connector attached to the

tube that runs underneath the freezer. The door cannot be removed if the connector is still attached to the tube that

runs through the door hinge.

4. Disconnect the wiring located behind the base grille on the freezer door side. See Graphic 4.

• Remove the wiring clip using a 1/4"hex-head socket

wrench.

• Disconnect wiring plugs.

5. Close both doors and keep them closed until you are ready to lift them free from the cabinet.

6. Use a 5/16"hex-head socket wrench to remove the top left hinge screw and cover as shown. See Graphic 5.

7. Remove remaining left hinge screws and hinge as shown. See Graphic 5.

IMPORTANT: Do not remove screw A.

8. Lift freezer door straight up off bottom hinge. See Graphic 6. The water dispenser tubing and wiring remain attached to the freezer door and pull through the bottom left hinge. Be sure to avoid damaging the dispenser tubing and wiring.

9. Remove top right hinge cover and screws as shown. See Graphic 7.

IMPORTANT: Do not remove screw A.

10.

Lift the refrigerator door straight up off bottom hinge.

11.

It may not be necessary to remove the bottom hinges to move the refrigerator through a doorway. Both bottom hinges

have similar construction.

• If necessary, disassemble the hinges as shown. See

Graphic 8. IMPORTANT: To aid in door alignment and closing, there

is a shim located between the hinge and the cabinet. When the hinge is removed, the shim may fall out of place. If this occurs, set the shim aside so it can be put back in place when the hinge is reconnected later.

Replace the Doors and Hinges

1. Replace both bottom hinges, if removed. Make sure the shim is between the hinge and cabinet. Tighten screws.

2. Feed the water dispenser tubing and wiring through the bottom left hinge before replacing the freezer door on the hinge. Assistance may be needed.

NOTE: Provide additional support for the doors while the top hinges are being replaced. Do not depend on the door magnets to hold the doors in place while you are working.

3. Align and replace the top left hinge as shown. See Graphic 5. Tighten screws.

4. Replace left hinge cover and screws.

5. Reconnect water dispenser tubing and wiring.

• Push tubing into fitting until it stops and the black mark

touches the face of fitting. See Graphic 3.

• Reconnect wiring plugs. Reinstall the wiring clip over the

grommets. Tighten screw. See Graphic 4.

6. Replace the refrigerator door by lifting the door onto the bottom right hinge.

7. Align and replace the top right hinge as shown. See Graphic 7. Tighten screws.

8. Replace hinge cover and screws. Tighten screws.

9. Plug into a grounded 3 prong outlet or reconnect power.

Door Closing

1. Place a level inside the refrigerator at the back of the top shelf. See Graphic 9 in "Refrigerator Doors."

2. Locate the leveling screws behind the base grille of the refrigerator on either side.

3. Use a hex-head wrench to adjust the rear roller leveling screws until the refrigerator is level. Turn the rear roller leveling screw to the right to raise that side of the refrigerator or turn the leveling screw to the left to lower that side. See Graphic 11 in "Refrigerator Doors." Make sure refrigerator is level before proceeding.

4. Check the door alignment after leveling the refrigerator.

Align the Doors

IMPORTANT: First level the back of the refrigerator as described

in "Door Closing."

The doors may be uneven after leveling the refrigerator. See

Graphic 10 in "Refrigerator Doors." The doors are preset at the factory so that the refrigerator door is higher than the freezer door by approximately the thickness of a quarter. Once the doors are loaded with food, they should be even. If the door height needs to be adjusted after the doors have been loaded with food, follow these steps.

1. Use a hex-head wrench to adjust the front roller leveling screws until the doors are even. Turn the front roller leveling screw to the right to raise that side of the refrigerator or turn the leveling screw to the left to lower that side. See Graphic 11 in "Refrigerator Doors."

NOTE: Open and close both the refrigerator and freezer doors after each adjustment to check the door alignment.

2. Open the doors and replace the base grille. Line up the grille support tabs with the metal clips. Push the grille firmly to snap it into place.

NOTE: Be sure to refasten the Tech Sheet behind the base grille.

Read all directions before you begin. IMPORTANT: If you turn the refrigerator on before the water line

is connected, turn the ice maker OFE

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw the compression nut onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten.

3. Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help avoid damage to the tubing when the refrigerator is pushed back against the wall.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

u__, A

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Locate a 1/2"(12.70 mm) to 11/4" (3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

Determine the length of copper tubing you need. Measure from the connection on the lower rear corner of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

Using a cordless drill, drill a 1/4"(6.35 mm) hole in the cold water pipe you have selected.

G,, ............B

A. Tube clamp

B.Copper tubing

The ice maker is equipped with a built-in water strainer. If

C. Compression nut D. Valve inlet

your water conditions require a second water strainer, install it in the 1/4"(6.35 mm) water line at either tube connection.

Obtain a water strainer from your nearest appliance dealer.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not long enough, a 1/4"x 1/4"(6.35 mm x 6.35 mm) coupling is needed

in order to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the

end of the copper tubing. NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

A. Cold water pipe E.Compression sleeve B.Pipe clamp F Shutoff valve C. Copper tubing G.Packing nut D. Compression nut

Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the 1/4"(6.35 mm)

drilled hole inthe water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp

screws slowly and evenly so the washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.

A B C D E F G

A. Refrigerator water tubing E. Ferrule (purchased)

B. Nut (provided) F Nut (purchased)

C. Bulb G. Household water fine D. Coupfing (purchased)

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water tube on the rear of the refrigerator.

3. Thread the provided nut onto the water valve as shown. NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

Style 1

Style 2

_II

A. Bulb B. Nut (provided)

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including connections at the valve) that leak.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

NOTE: If your model has a base grille filter system, make sure the base grille filter is properly installed and the cartridge cap handle

is in the horizontal position.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain

filterable cysts.

2. Use a sturdy container to depress and hold the water dispenser lever for 5 seconds, then release it for 5 seconds.

Repeat until water begins to flow. Once water begins to flow, continue depressing and releasing the dispenser lever

(5 seconds on, 5 seconds off) for an additional 5 minutes. This will flush air from the filter and water dispensing system.

Additional flushing may be required in some households. NOTE: As air is cleared from the system, water may spurt out

of the dispenser.

3. Open the freezer door and turn on the ice maker. For Style 1, lower the wire shutoff arm. For Style 2, move the switch to the ON (left) position. Please refer to the "Ice Maker and Storage Bin" section for further instructions on the operation of your ice maker.

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced.

• Depending on your model, you may want to select the

maximum ice feature to increase the production of ice.

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See "Prepare the Water System" or "Water and Ice Dispensers."

NOTE: Allow 24 hours to produce the first batch of ice. Allow 3 days to completely fill ice container.

Please read before using the water system. Immediately after installation, follow the steps below to make

sure that the water system is properly cleaned.

1. Open the freezer door and turn off the ice maker. For Style 1, lift up the wire shutoff arm as shown. For Style 2, move the switch to the OFF (right) setting as shown. The On/Off switch is located on the top right side of the freezer compartment.

Your new refrigerator may make sounds that your old one didn't make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard surfaces, such as the floor, walls, and cabinets, can make the

sounds seem louder. The following describes the kinds of sounds and what may be making them.

• If your refrigerator is equipped with an ice maker, you will hear a buzzing sound when the water valve opens to fill the ice maker for each cycle.

• Your refrigerator is designed to run more efficiently to keep your food items at the desired temperatures and to minimize energy usage. The high efficiency compressor and fans may cause your refrigerator to run longer than your old one. You may also hear a pulsating or high-pitched sound from the compressor or fans adjusting to optimize performance.

• You may hear the evaporator fan motor circulating air through the refrigerator and freezer compartments. The fan speed may increase as you open the doors or add warm food.

• Rattling noises may come from the flow of refrigerant, the water line, or items stored on top of the refrigerator.

• Water dripping on the defrost heater during a defrost cycle may cause a sizzling sound.

• As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your refrigerator.

• Contraction and expansion of the inside walls may cause a popping noise.

• You may hear air being forced over the condenser by the condenser fan.

You may hear water running into the drain pan during the defrost cycle.

REFRIGERATOR USE

In order to ensure proper temperatures, you need to permit air to flow between the two sections. Cold air enters the bottom of the

freezer section and moves up. It then enters the refrigerator section through the top vent. Air then returns to the freezer as

shown.

Toturn cooling off, press and hold the TEMP and FILTER buttons at the same time for 3 seconds. Press and hold TEMP and

FILTER again to turn cooling on. Your refrigerator and freezer will not cool when cooling is off.

IMPORTANT: To avoid unintentionally changing other settings, be sure to press both buttons at exactly the same

time.

For your convenience, your refrigerator and freezer controls are preset at the factory. When you first install your refrigerator, make sure that the controls are still set to the "mid-settings."

To view set points, press the TEMP button on your dispenser panel. The factory recommended set points are 0°F (-18°C) for the freezer and 37°F (3°C) for the refrigerator.

IMPORTANT:

• Wait 24 hours before you put food into the refrigerator. If you add food before the refrigerator has cooled completely, your food may spoil.

NOTE: Adjusting the set points to a higher (colder) than recommended setting will not cool the compartments any

faster.

• If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls.

• The preset settings should be correct for normal household usage. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.

• Wait at least 24 hours between adjustments. Recheck the temperatures before other adjustments are made.

• The display screen on the dispenser control panel has a backlight, which will turn off automatically when the control

buttons have not been used for 30 seconds or more. When the backlight is off, the first press of a control button will only

reactivate the backlight, without changing any settings. Within 30 seconds after the backlight has been reactivated, additional presses of control buttons will change the applicable settings.

Do not block any airflow vents. If the vents are blocked, airflow will be obstructed and temperature and moisture problems may

occur. IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

Usn9 the Co st c÷s

Temperature Control Adjustment and Cooling On/Off

The refrigerator and freezer control buttons are located on the

dispenser panel.

s_tsense

? 6

cubed

ice [Acceier IceI

off unlocked

Light Lock

Adjusting the Controls

To adjust the set points, press and hold the TEMP button for 3 seconds. When adjust mode is activated, set points and

adjusting information will appear on the display screen.

r RECOMMENDED(dF) FREEZER REFRIGERATOR(3¢F) RECOMMENDE_

.oits°F°cl v I ""

NOTE: To view Celsius temperatures, press the UNITS button when adjust mode is activated. To return the display setting to Fahrenheit, press UNITS again.

Refrigerator Controls When adjust mode is activated, the fourth and fifth buttons (from

the left) adjust the refrigerator compartment temperature. The set point range for the refrigerator is 33°F to 45°F (0°C to 7°C).

• Press the fourth button (down arrow) to lower the set point.

• Press the fifth button (up arrow) to raise the set point.

rl°F --I --I°F U _J I

v I ^ I Retorn

Freezer Controls

When adjust mode is activated, the second and third buttons (from the left) adjust the freezer compartment temperature. The set point range for the freezer is -5°F to 5°F (-21°C to -15°C).

• Press the second button (down arrow) to lower the set point.

• Press the third button (up arrow) to raise the set point.

CONDITION: TEMPERATURE

ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR Setting

1° higher

REFRIGERATOR too warm REFRIGERATOR Setting

1° lower

FREEZER too cold FREEZER Setting

1° higher

FREEZER too warm/too little ice FREEZER Setting

1° lower

Door Ajar Alarm The Door Ajar Alarm feature sounds an alarm when the

refrigerator or freezer door is open for 5 minutes and the product cooling is turned on. The alarm will repeat every 2 minutes. Close

both doors to turn it off. The feature then resets and will reactivate when either door is left open again for 5 minutes.

Disabling Sounds

• To turn off all dispenser and control sounds, including the Door Ajar Alarm, press and hold ICE and TEMP at the same

time for 3 seconds. IMPORTANT: To avoid unintentionally changing other

settings, be sure to press both buttons at exactly the same time.

• To turn all sounds back on, press and hold ICE and TEMP at the same time for 3 seconds again.

Press RETURN to exit adjust mode, or allow about 15 seconds of inactivity and adjust mode will turn off automatically.

Additional Features

Accelerated Ice Production

The Accelerated Ice feature assists with temporary periods of

heavy ice usage by increasing ice production over a 24-hour period.

• Press the ACCELER ICE button to turn on the feature. The display screen indicates whether the feature is on or off.

ON OFF

The Accelerated Ice setting will remain on for 24 hours unless manually turned off. The display will continue to show your

normal temperature set point.

NOTE: If increased ice production is desired at all times, change the freezer control to a lower setting. Setting the freezer to a

colder temperature may make some foods, such as ice cream, harder.

SmartSense TM Temperature Management

The SmartSense TM feature assists with regulating the

temperature inside the refrigerator and freezer. If a large quantity of warm food is placed in the refrigerator or warm air enters the

refrigerator while the door is held open, SmartSense TM activates to quickly restore the temperature to the set point.

smartsense

Depending on your model, you may have one or more of the following options: the ability to select either crushed or cubed ice, a special light that turns on when you use the dispenser, or a lock option to avoid unintentional dispensing.

The Water Dispenser

If you did not flush the water system when the refrigerator was first installed, do so now. Use a sturdy container to depress and hold the water dispenser lever for 5 seconds, then release it for 5 seconds. Repeat until water begins to flow. Once water begins to flow, continue depressing and releasing the dispenser lever (5 seconds on, 5 seconds off) for an additional 5 minutes. This will flush air from the filter and water dispensing system. Additional flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of the dispenser.

Allow 24 hours for the refrigerator to cool down and chill water. IMPORTANT: Depending on your model, the small removable

tray at the bottom of the dispenser is designed to catch small spills and allow for easy cleaning. There is no drain in the tray. The tray can be removed from the dispenser and carried to the sink to be emptied or cleaned.

To Dispense Water:

1. Press a sturdy glass against the water dispenser lever.

NOTE: SmartSense TM is always on when your refrigerator is operating. You do not need to press any buttons to activate it.

The SmartSense TM icon on the dispenser display screen

indicates that the feature is functioning properly.

Temperature Display Always On

This feature keeps the temperature display on at all times.

• Press and hold TEMP and LOCK at the same time for 3 seconds to turn the feature on.

IMPORTANT: To avoid unintentionally locking the dispenser or changing other settings, be sure to press both buttons at exactly the same time.

Press and hold TEMP and LOCK at the same time for 3 seconds again to turn the feature off.

2. Remove the glass to stop dispensing. NOTE: Water may have an off-flavor if you do not use the

dispenser periodically. Dispense enough water every week to maintain a fresh supply.

The Ice Dispenser

The Dispenser Light (on some models)

Ice dispenses from the ice maker storage bin in the freezer when the dispenser lever is pressed. The dispensing system will not operate when the freezer door is open. To turn off the ice maker, see "Ice Maker and Storage Bin."

Your ice maker can produce both crushed and cubed ice. Before dispensing ice, select which type of ice you prefer by pressing

the ICE button.

The display screen indicates which type of ice is selected.

crushed

CRUSHED

For crushed ice, cubes are crushed before being dispensed. This may cause a slight delay when dispensing crushed ice. Noise from the ice crusher is normal, and pieces of ice may vary in size. When changing from crushed to cubed, a few ounces of crushed ice will be dispensed along with the first cubes.

To Dispense Ice:

1. Press the button to select the desired type of ice.

Cut Hazard

Use a sturdy glass when dispensing ice. Failure to do so can result in cuts.

Press a sturdy glass against the ice dispenser lever. Hold the glass close to the dispenser opening so ice does not fall outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to the lever in order to activate the ice dispenser. Pressing hard

will not make the ice dispense faster or in greater quantities.

Remove the glass to stop dispensing. NOTE: Ice may continue to dispense for up to 10 seconds

after removing the glass from the lever. The dispenser may continue to make noise for a few seconds after dispensing.

cubed

CUBED

When you use the dispenser, the light will automatically turn on. If you want the light to be on continuously, you may choose either ON or HALE The display screen indicates which mode is

selected.

\!/ ',,A/

-;O,- ,0, 0

g u u

on half off

ON HALF OFF

ON: Press LIGHT to turn the dispenser light on. HALF: Press LIGHT a second time to select HALF mode. The

dispenser light will remain on, but at a lower intensity. OFF: Press LIGHT a third time to turn the dispenser light off. The dispenser lights are LEDs that can not be changed. If it

appears that your dispenser lights are not working, see "Troubleshooting" for more information.

The Dispenser Lock (on some models)

The dispenser can be turned off for easy cleaning or to avoid unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the refrigerator, to the ice maker, or to the dispenser light. It simply deactivates the dispenser controls and levers. To turn off the ice maker, see "Ice Maker and Storage Bin."

• Press and hold LOCK for 3 seconds to lock the dispenser.

• Press and hold LOCK a second time to unlock the dispenser. The display screen indicates when the dispenser is locked.

db 6

locked unlocked

LOCKED UNLOCKED

Lght

The water filter status light will help you know when to change your water filter. When the water filter status display changes from "GOOD" to "ORDER," this tells you that it is almost time to change the water filter cartridge. Replace the water filter cartridge when the water filter status display changes to "REPLACE." If water flow to your water dispenser or ice maker decreases noticeably, change the filter sooner. The filter should be replaced at least every 6 months depending on your water quality and usage. To change the filter, see "Water Filtration System."

INDICATOR: STATUS: NEW or GOOD (green) New filter installed

ORDER (yellow) Order filter REPLACE (red) OR Replace water filter

when water flow decreases

After changing the water filter, reset the status light by pressing

and holding the FILTER button for 3 seconds. The status light will change from Replace (red) to New/Good (green) when the system

is reset.

Style 1 Style 2

,_new

good

order

L replace

GOOD ORDER

REPLACE

PRESS & HOLD

TO RESET Filter Status

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain

filterable cysts.

Changing the Water Filter

The water filter is located in the base grille below the freezer

compartment door. It is not necessary to remove the base grille to remove the filter.

1. Remove the filter by pressing the eject button and pulling straight out on the filter cap.

NOTES:

Avoid twisting the cap when removing the filter because this could cause the cap to come off. If this occurs, replace the cap and pull the filter straight out.

• There will be water in the filter. Some spilling may occur.

A ...................................................................

Take the new cartridge out of its packaging and remove the covers from O-rings.

..........................

A. Cover

B. O-ring

Place the cap (removed in Step 2) on the new filter. Align the ridge on the cap with the arrow on the filter. Turn the cap clockwise until it snaps into place.

A. Eject button

B. Arrow on filter C. Ridge on cap

5. Push the new filter into the opening in the base grille. As the filter is inserted, the eject button will depress. The eject button will pop back out when the filter is fully engaged.

6. Pull gently on the cap to check that the filter is securely in place.

7. Flush the water system. See "Flushing the Water System After Changing Filter."

A. Eject button

B. Filter cap

2. Remove the cap by turning it counterclockwise until it stops. IMPORTANT: Do not discard the cap. It is part of your

refrigerator. Keep the cap to use with the replacement filter.

Flushing the Water System After Changing Filter

After connecting the refrigerator to a water source, flush the water system. Use a sturdy container to depress and hold the water dispenser lever for 5 seconds, then release it for 5 seconds. Repeat until water begins to flow. Once water begins to flow, continue depressing and releasing the dispenser lever (5 seconds on, 5 seconds off) for an additional 5 minutes. This will flush air from the filter and water dispensing system. Additional flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of the dispenser.

Using the Dispenser Without the Water Filter Cartridge

You can run the dispenser without a water filter cartridge. Your water will not be filtered.

1. Remove the filter by pressing the eject button and pulling on the cap. See "Changing the Water Filter" earlier in this

section.

2. Remove the cap by turning it counterclockwise until it stops. IMPORTANT: Do not discard the cap. It is part of your

refrigerator. Keep the cap to use with the replacement filter.

3. With the cap in a horizontal position, insert the cap into the base grille until it stops.

• Maximum Ice Production (on some models): In maximum ice production, the ice maker should produce approximately 10 to 14 batches of ice in a 24-hour period. If your refrigerator has the maximum ice production feature, push the switch to MAX.

Style 2:

The On/Off switch is located on the top right side of the freezer compartment.

1. To turn the ice maker on, slide the control to the ON (left) position.

NOTE: Your ice maker has an automatic shutoff. The ice maker sensors will automatically stop ice production, but the

control will remain in the ON (left) position.

2. To manually turn the ice maker off, slide the control to the OFF (right) position.

Turn the cap counterclockwise until the cap slips into the attachment slot. Then, turn the cap clockwise until it is in a horizontal position.

NOTE: The cap will not be even with the base grille.

Turning the Ice Maker On/Off

Style 1:

The On/Off switch for the ice maker is a wire shutoff arm located

on the side of the ice maker.

1. To turn the ice maker on, simply lower the wire shutoff arm. NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes will fill the ice storage bin and the ice cubes will raise the wire shutoff arm to the OFF (arm up) position.

2. To manually turn the ice maker off, lift the wire shutoff arm to the OFF (arm up) position and listen for the click to make sure the ice maker will not continue to operate.

Removing and Replacing the Storage Bin

Style 1:

1. Pull the covering panel out from the bottom and then slide it back toward the rear.

2. Lift the wire shutoff arm so it clicks into the OFF (up) position. Ice can still be dispensed, but no more can be made.

3. Lift up the front of the storage bin and pull it out.

4. Replace the bin by pushing it in all the way or the dispenser will not work. Push the wire shutoff arm down to the ON

position to restart ice production. Make sure the door is closed tightly.

Style 2:

1. Hold the base of the storage bin with both hands and press the release button to lift the storage bin up and out.

NOTE: It is not necessary to turn the ice maker control to the OFF (right) position when removing the storage bin. The sensor cover ("flipper door") on the left wall of the freezer stops the ice maker from producing ice if the door is open or the storage bin is removed.

2. Replace the storage bin on the door and push down to make sure it is securely in place.

To Increase Ice Production Rate:

Normal Ice Production: In normal ice production mode, the ice maker should produce approximately 7 to 9 batches of ice in a

24-hour period. If ice is not being made fast enough, turn the Freezer Control toward a higher (colder) number in

half number steps. (For example, if the control is at 3, move it to between 3 and 4.) Wait 24 hours between each

increase.

Cleaning the Storage Bin

1. Empty the ice container. Use warm water to melt the ice if necessary.

NOTE: Do not use anything sharp to break up the ice in the bin. This can cause damage to the ice container and the dispenser mechanism.

2. Wash ice bin with a mild detergent, rinse well and dry thoroughly. Do not use harsh or abrasive cleaners or solvents.

Remember

• Allow 24 hours to produce the first batch of ice. Allow 3 days to completely fill ice container.

• Discard the first three batches of ice produced to avoid impurities that may be flushed out of the system.

• The quality of your ice will be only as good as the quality of the water supplied to your ice maker.

• Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.

It is normal for the ice cubes to be attached at the corners. They will break apart easily.

For Style 1 ice maker, do not force the wire shutoff arm up or down.

Do not store anything on top of the ice maker or in the ice storage bin.

Yourmodel may have glass or wire shelves. Store similar foods together and adjust the shelvesto fit different heights. This reduces the timethe refrigerator door isopen and saves energy.

Shelves and Shelf Frames (Fixed and Slide-out)

To Remove and Replace a Shelf:

1. Pull the shelf forward to the stop. Tilt the front of the shelf up. Lift to remove from the shelf supports.

2. Replace the shelf/frame by aligning the shelf with the shelf supports. Slide the shelf onto the shelf supports. Be sure that the shelf is securely in position.

The deli drawer stores raisins, nuts, spreads, and other small items at normal refrigerator temperatures.

To Remove and Replace the Deli Bin:

1. Remove the deli bin by sliding it straight out to the stop. Lift the front and back of the bin up and out of the shelf supports. Tilt the bin sideways to remove from the refrigerator compartment.

2. Replace the deli bin by sliding it back past the stop and pushing into place.

REFRIGERATOR FEATURES

Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word "Accessory." Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please

call the toll-free number on the back cover or in the "Accessories" section.

important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when removing them to avoid impact from dropping.

(0_' ::f_e !'_""'so ,,,,se ;_>_;_'"

Crisper and Convertible Vegetable Meat Drawers

To Remove and Replace Drawers:

1. Slide crisper or meat drawer straight out to the stop. Lift the front of drawer with one hand while supporting the bottom of

drawer with other hand and slide the drawer out the rest of the way.

2. Replace the crisper or meat drawer by sliding it back in fully past the drawer stop.

Crisper or Vegetable/Meat Drawer Covers

To Remove and Replace Covers:

1. Remove the crisper and meat drawers. Press up in center of crisper glass insert until it rises above the plastic frame. Holding the crisper glass firmly, slide the glass insert forward

to remove.

2. Lift crisper cover frame and remove. Repeat steps to remove the meat drawer cover.

Replace the shelf by inserting the left side of the shelf into the support holes. Lower the right side of the shelf and insert into support holes.

NOTE: Be sure that both sides of the shelf are positioned evenly in the shelf support holes and the shelf is secure.

Style 2

3. Replace back of meat drawer cover frame into supports or slides on side walls of the refrigerator and lower or slide the

front of the cover frame into place.

4. Slide rear of glass insert into cover frame and lower front into place. Repeat steps to replace the crisper cover.

Wse

To Install and Remove the Wine Rack:

1. Install the wine rack by aligning it with the three shelf tabs located on the bottom of the shelf. Pull the wine rack straight

down until it locks onto the shelf tabs as shown.

2. To remove the wine rack, lift it straight up and off the shelf tabs.

_>_*;some mo(%s ,._A#i;.O o_i

NOTE: For long-term storage, place eggs in a covered container or in their original carton on an interior shelf.

To Remove and Replace the Shelf:

1. Lift the shelf up and off the supports.

2. Replace the shelf by lowering it onto the shelf supports. Be sure that the shelf is securely in place.

Frozen Food Storage Guide

Storage times will vary according to the quality and type of food, the type of packaging or wrap used (should be airtight and

moisture-proof), and the storage temperature. Ice crystals inside a sealed package are normal. This simply means that moisture in

the food and air inside the package have condensed, creating ice crystals. Put no more unfrozen food into the freezer than will freeze within

24 hours (no more than 2 to 3 Ibs of food per cubic foot [907 to 1,360 g per 28 L] of freezer space). Leave enough space

in the freezer for air to circulate around packages. Be sure to leave enough room for the door to close tightly.

For more information on preparing food for freezing, check a freezer guide or reliable cookbook.

FREEZER FEATURES

call the toll-free number on the cover or in the "Accessories" section.

Style 1

To Remove and Replace the Shelf:

1. Slide the shelf to one side. Tilt the shelf upward to remove the

shelf from the support holes. To remove the left side from the support holes, pull the shelf up and to the right.

Bas B

_s ast c bs on so_se mode@

The freezer basket or bin can be used to store bags of frozen fruits and vegetables that may slide oft freezer shelves.

To Remove and Replace the Freezer Basket or Bin:

1. Remove basket or bin by sliding it out to the stop.

2. Lift the front of the basket or bin and slide it out the rest of the way.

Replace the basket or bin by positioning it on the side wall guide rails. Lift the basket or bin front slightly while pushing it past the guide rail stops and slide basket or bin in the rest of the way.

DOOR FEATURES

call the toll-free number on the cover or in the "Accessories" section.

REFRIGERATOR CARE

©o@ Rss Bns

The door rails may be removed for easier cleaning.

Snap-On Door Rails or Bins

To Remove and Replace the Rails or Bins:

1. Remove the rails by pushing in slightly on the front of the bracket while pulling out on the inside tab. Repeat these steps for the other end of the rail.

2. Replace the rails by aligning the ends of the brackets with the buttons on the sides of the door liner. Firmly snap bracket and rail assembly onto the tabs above the shelf as shown.

Drop-In Door Rails

To Remove and Replace the Rails:

1. Remove the rails by pulling straight up on each end of the rail.

2. Replace the rails by sliding the shelf rail into the slots on the door and pushing the rail straight down until it stops.

©oo Bns

To Remove and Replace the Bins:

1. Remove the bin by lifting it and pulling it straight out.

2. Replace the bin by sliding it in above the desired support and pushing it down until it stops.

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically. However, clean both compartments about once a month to avoid

buildup of odors. Wipe up spills immediately.

To Clean Your Refrigerator:

1. Unplug refrigerator or disconnect power.

2. Remove all removable parts from inside, such as shelves, crispers, etc.

3. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

• Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on plastic parts, interior and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools. These can scratch or damage materials.

• To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs to 1 qt [26 g to 0.95 L] of water).

4. Determine whether your refrigerator exterior is painted metal, brushed aluminum or stainless steel and choose the

appropriate cleaning method. Painted metal: Wash exteriors with a clean sponge or soft

cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners, or cleaners designed for stainless steel. Dry thoroughly with a soft cloth. Additionally, to avoid damage to painted metal exteriors, apply appliance wax (or auto paste wax) with a clean, soft cloth. Do not wax plastic parts.

Brushed aluminum: Wash with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners, or cleaners designed for stainless steel. Dry thoroughly with a soft cloth.

Stainless steel finish: Wash with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners. Dry thoroughly with a soft cloth.

• To keep your stainless steel refrigerator looking like new

and to remove minor scuffs or marks, it is suggested that you use the manufacturer's approved Stainless Steel

Cleaner and Polish. To order the cleaner, see the "Accessories" section.

IMPORTANT: This cleaner is for stainless steel parts only!

Do not allow the Stainless Steel Cleaner and Polish to come into contact with any plastic parts such as the trim pieces,

dispenser covers or door gaskets. If unintentional contact does occur, clean plastic part with a sponge and mild detergent in warm water. Dry thoroughly with a soft cloth.

There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille. See "Base Grille" graphic or "Base Grille" section.

• Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to replace the bulb with one of the same size and shape. The dispenser light requires a heavy duty 1O-watt bulb. All other lights require a 40-watt appliance bulb. Replacement bulbs are available from your dealer.

1. Unplug refrigerator or disconnect power.

2. Remove light shield when applicable as shown. NOTE: To clean the light shield, wash it with warm water and

liquid detergent. Rinse and dry the shield well.

3. Remove light bulb and replace with one of the same size, shape and wattage.

4. Replace light shield when applicable as shown.

5. Plug in refrigerator or reconnect power.

Dispenser Light (on some models)

Refrigerator Control Panel Light

Reach behind the refrigerator control panel to remove and replace light bulb.

Crisper Lights

If necessary, remove the top crisper drawer to access the crisper light shield. Remove the light shield by lifting the ends

out of the brackets as shown. Replace the light shield by inserting the ends into the

brackets. If necessary, replace the top crisper drawer.

Upper Freezer Light (on some models)

Style 1

• Remove light shield by grasping the top center of the shield and pulling forward while turning it slightly to one side. If necessary, remove top crisper drawer to gain access to the crisper light shield.

• Replace the light shield by inserting the tabs on one end into the slotted holes in the refrigerator or freezer liner. Then, bend

the shield at the center to insert the tabs on the other end.

Reach through the dispenser area to remove and replace light bulb.

A. Dispenserlight

NOTE: On some models, the dispenser lights are LEDs that can not be changed.

Style 2

• Remove the light shield by squeezing the sides of the light shield in toward the center while pulling the shield forward as

shown. Replace the light shield by fitting the tabs into the slotted

holes in the freezer liner. Push in the shield until it snaps into place.

Lower Freezer Light (on some models)

Style 1 - Beneath Ice Bin

• Remove the light shield by grasping the sides and squeezing in toward the center. Once the side hooks of shield are free

from the freezer lining, pull down the shield.

• Replace the light shield by squeezing the sides toward the center and inserting the side hooks into the slotted holes. Once the side hooks are in place, snap the front tab into the

slotted hole.

Style 2 - Behind Freezer Basket

• Depending on your model, remove the top freezer basket or top freezer basket shelf. Remove light shield by removing the Phillips screw on the top of the shield. Gently rotate the shield until the left tab can be pulled from the freezer wall.

• Replace the light shield by inserting the left tab into the freezer wall. Align top tab with screw hole and replace screw.

Vacations

If You Choose to Leave the Refrigerator On While You're Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker:

• Raise wire shutoff arm to OFF (up) position or move the switch to the OFF (right) setting.

• Shut off water supply to the ice maker.

3. Empty the ice bin.

If You Choose to Turn the Refrigerator Off Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day ahead of time.

• When the last load of ice drops, raise the wire shutoff arm to the OFF (up) position or move the switch to the OFF (right) setting.

3. Depending on the model, turn the Temperature Control or Refrigerator Control to OFE See "Using the Controls."

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in. This stops odor and mold from building up.

If the power will be out for 24 hours or less, keep the door or doors closed (depending on your model) to help food stay cold

and frozen. If the power will be out for more than 24 hours, do one of the

following:

• Remove all frozen food and store it in a frozen food locker.

• Place 2 Ibs (907 g) of dry ice in the freezer for every cubic foot (28 L) of freezer space. This will keep the food frozen for 2 to 4 days.

• If neither a food locker nor dry ice is available, consume or can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled one. A freezer full of meat stays cold longer than a freezer full of baked goods. If you see that food contains ice crystals, it may be refrozen, although the quality and flavor may be affected. If the condition of the food is poor, dispose of it.

Moving

When you are moving your refrigerator to a new home, follow these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day ahead of time.

• Disconnect the water line from the back of the refrigerator.

• When the last load of ice drops, raise the wire shutoff arm to the OFF (up) position or move the switch to the OFF (right) setting.

2. Remove all food from the refrigerator and pack all frozen food in dry ice.

3. Empty the ice bin.

4. Depending on the model, turn the Temperature Control or Refrigerator Control to OFF. See "Using the Controls."

5. Unplug refrigerator.

6. Empty water from the defrost pan.

7. Clean, wipe, and dry thoroughly.

8. Take out all removable parts, wrap them well, and tape them together so they don't shift and rattle during the move.

9. Depending on the model, raise the front of the refrigerator so it rolls more easily OR screw in the leveling legs so they don't scrape the floor. See "Adjust the Doors."

10. Tape the doors closed and tape the power cord to the back of the refrigerator.

When you get to your new home, put everything back and refer to the "Installation Instructions" section for preparation instructions. Also, if your refrigerator has an automatic ice maker, remember to reconnect the water supply to the refrigerator.

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.

The refrigerator will not operate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

• Power cord unplugged? Plug into a grounded 3 prong

outlet.

• Is outlet working? Plug in a lamp to see if the outlet is working.

• Household fuse blown or circuit breaker tripped? Replace the fuse or reset the circuit breaker. If the problem continues,

call an electrician. Are controls on? Make sure the refrigerator controls are on.

See "Using the Controls." New installation? Allow 24 hours following installation for

the refrigerator to cool completely. NOTE: Adjusting the temperature controls to coldest setting

will not cool either compartment more quickly.

The refrigerator is noisy

Refrigerator noise has been reduced over the years. Due to this reduction, you may hear intermittent noises from your new refrigerator that you did not notice from your old model. Below are listed some normal sounds with an explanation.

• Buzzing - heard when the water valve opens to fill the ice maker

• Pulsating- fans/compressor adjusting to optimize performance

• Rattling - flow of refrigerant, water line, or from items placed on top of the refrigerator

• Sizzling/Gurgling - water dripping on the heater during defrost cycle

• Popping - contraction/expansion of inside walls, especially during initial cool-down

• Water running - may be heard when water melts during the defrost cycle and runs into the drain pan

• Creaking/Cracking - occurs as ice is being ejected from the ice maker mold.

The doors will not close completely

• Door blocked open? Move food packages away from door.

• Bin or shelf in the way? Push bin or shelf back in the correct position.

The doors are difficult to open

The motor seems to run too much

Your new refrigerator may run longer than your old one due to its high-efficiency compressor and fans. The unit may run even longer if the room is warm, a large food load is added, doors are opened often, or if the doors have been left open.

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

• Are the gaskets dirty or sticky? Clean gaskets with mild soap and warm water.

The lights do not work

• Is a light bulb loose in the socket or burned out? See "Changing the Light Bulbs."

• Is the dispenser light set to OFF? The dispenser light will operate only when the levers are pressed. If you want the dispenser light to stay on continuously, set the dispenser light to ON, or NIGHT LIGHT or AUTO or HALF or DIM. See "Water and Ice Dispensers."

• Is the dispenser light set to NIGHT LIGHT or AUTO? If the dispenser is set to the NIGHT LIGHT or AUTO mode, be sure the dispenser light sensor is not blocked. See "Water and Ice Dispensers."

Temperature is too warm

• New installation? Allow 24 hours following installation for the refrigerator to cool completely.

• Door(s) opened often or left open? Allows warm air to enter refrigerator. Minimize door openings and keep doors fully

closed.

• Large load of food added? Allow several hours for refrigerator to return to normal temperature.

• Controls set correctly for the surrounding conditions? Adjust the controls a setting colder. Check temperature in 24 hours. See "Using the Controls."

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

• Humid room? Contributes to moisture buildup.

• Door(s) opened often or left open? Allows humid air to enter refrigerator. Minimize door openings and keep doors fully closed.

• Large amount of ice recently removed? Allow 24 hours for ice maker to produce more ice.

• Ice cube jammed in the ice maker ejector arm? Remove ice from the ejector arm with a plastic utensil.

• Reverse osmosis water filtration system connected to your cold water supply? This can decrease water pressure. See "Water Supply Requirements."

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

• Water shutoff valve not fully open? Turn the water shutoff valve fully open.

• Kink in the water source line? A kink in the line can reduce water flow. Straighten the water source line.

• Reverse osmosis water filtration system connected to your cold water supply? This can decrease water pressure. See "Water Supply Requirements."

• Questions remain regarding water pressure? Call a licensed, qualified plumber.

Off-taste, odor or gray color in the ice

New plumbing connections? New plumbing connections

can cause discolored or off-flavored ice. Ice stored too long? Discard ice. Wash ice bin. Allow

24 hours for ice maker to make new ice. Odor transfer from food? Use airtight, moisture proof

packaging to store food. Are there minerals (such as sulfur) in the water? A water

filter may need to be installed to remove the minerals. Is there a water filter installed on the refrigerator? Gray or

dark discoloration in ice indicates that the water filtration system needs additional flushing.

The ice dispenser will not operate properly

ce and e

The ice maker is not producing ice or not enough ice

• Refrigerator connected to a water supply and the supply shutoff valve turned on? Connect refrigerator to water supply and turn water shutoff valve fully open.

Kink in the water source line? A kink in the line can reduce water flow. Straighten the water source line.

Ice maker turned on? Make sure wire shutoff arm or switch (depending on model) is in the ON position.

New installation? Wait 24 hours after ice maker installation for ice production to begin. Wait 72 hours for full ice

production.

• Freezer door closed completely? Close the door firmly. If it does not close completely, see "The doors will not close completely."

• Ice bin installed correctly? Be sure the ice bin is firmly in position.

• New installation? Wait 24 hours after ice maker installation for ice production to begin. Wait 72 hours for full ice

production.

• Ice stuck in the delivery chute? Use a plastic utensil to clear the delivery chute.

• Has the wrong ice been added to the bin? Use only cubes produced by the current ice maker.

• Has the ice melted around the auger (metal spiral) in the ice bin? Empty the ice container. Use warm water to melt the ice if necessary.

Cut Hazard

Use a sturdy glass when dispensing ice. Failure to do so can result in cuts.

• Is the ice dispenser stalling while dispensing "crushed" ice? Change the ice button from "crushed" to "cubed." If

cubed ice dispenses correctly, depress the button for "crushed" ice and begin dispensing again.

• Has the dispenser arm been held in too long? Ice will stop dispensing when the arm is held in too long. Wait 3 minutes for dispenser motor to reset before using again.

The water dispenser will not operate properly

Water is leaking from the dispenser

NOTE: One or two drops of water after dispensing is normal.

• Glass not being held under the dispenser long enough? Hold the glass under the dispenser 2 to 3 seconds after releasing the dispenser lever.

• New installation? Flush the water system. See "Prepare the Water System" or "Water and Ice Dispensers."

• Recently changed water filter? Flush the water system. See "Prepare the Water System" or "Water and Ice Dispensers."

The dispenser water is not cool enough

NOTE: Water from the dispenser is chilled to only 50°F (10°C).

• New installation? Allow 24 hours after installation for the water supply to cool completely.

• Recently dispensed large amount of water? Allow 24 hours for water supply to cool completely.

• Water not been recently dispensed? The first glass of water may not be cool. Discard the first glass of water.

• Refrigerator connected to a cold water pipe? Make sure the refrigerator is connected to a cold water pipe. See "Water Supply Requirements."

• Freezer door closed completely? Close the door firmly. If it does not close completely, see "The doors will not close completely."

• Refrigerator connected to a water supply and the supply shutoff valve turned on? Connect refrigerator to water supply and turn water shutoff valve fully open.

• Is the water pressure at least 30 psi (207 kPa)? The water pressure to the home determines the flow from the dispenser. See "Water Supply Requirements."

Kink in the home water source line? Straighten the water source line.

• New installation? Flush and fill the water system.

• Water filter installed on the refrigerator? The filter may be clogged or incorrectly installed.

• Is a reverse osmosis water filtration system connected to

your cold water supply? See "Water Supply Requirements."

PROTECTION AGREEMENTS

Master Protection Agreements

Congratulations on making a smart purchase. Your new Kenmore ®product is designed and manufactured for years of dependable operation. But like all products, it may require preventive maintenance or repair from time to time. That's when having a Master Protection Agreement can save you money and aggravation.

The Master Protection Agreement also helps extend the life of your new product. Here's what the Agreement* includes:

Parts and labor needed to help keep products operating properly under normal use, not just defects. Our coverage goes well beyond the product warranty. No deductibles, no functional failure excluded from coverage-- real protection.

Expert service by a force of more than 10,000 authorized Sears service technicians, which means someone you can

trust will be working on your product. Unlimited service calls and nationwide service, as often as

you want us, whenever you want us. "No-lemon" guarantee - replacement of your covered

product if four or more product failures occur within twelve months.

Product replacement if your covered product can't be fixed.

Annual Preventive Maintenance Check at your request - no

extra charge. Fast help by phone - we call it Rapid Resolution - phone

support from a Sears representative on all products. Think of us as a "talking owner's manual."

Power surge protection against electrical damage due to power fluctuations.

$250 Food Loss Protection annually for any food spoilage that is the result of mechanical failure of any covered refrigerator or freezer.

Rental reimbursement if repair of your covered product takes longer than promised.

10% discount off the regular price of any non-covered repair service and related installed parts.

Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime day or night, or schedule a service appointment online.

The Master Protection Agreement is a risk free purchase. If you cancel for any reason during the product warranty period, we will provide a full refund. Or, a prorated refund anytime after the product warranty period expires. Purchase your Master Protection Agreement today!

Some limitations and exclusions apply. For prices and additional information in the U.S.A. call 1-800-827-6655.

*Coverage in Canada varies on some items. For full details

call Sears Canada at 1-800-361-6665.

Sears Installation Service

For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, in the

U.S.A. or Canada call 1-800-4-MY-HOME e.

ACCESSORIES

WATER FILTER

CERTIFICATIONS

Stale of Catifbrn ia

Department of Health Services

Water Treatment Device

Certificate Number

04 - 1605

Date Issued: Jalmary 5,2004

Dale Revised: December 14, 2(,'05

Trademark/Model Designation

Kenmore Advanced Rebigelalor Filter TI KB I Kenmore TIKB1

Kenmore Ul{imate T I KB l Kenmole Ulfimale II T1KBI

Manufactm'er: Sears, Roebuck an_l Comp_g_

Chlorobenzene Cblor0Ncr{g

2 4-D DBCP

o-DichlorobeIlZc.'h_ p-Dichlorobenk_n_

L2-Dichloroethane

1,1-Dichloroethylen_

cis- 1,2-Dichloroethylen_ trails- 1,2-Diehloroethylene

],2-Dichloropropane

cis-1,3-Dichloropropylene Dinoseb

Rated Service Capacity: 100ga] Rated Service FIow: 05gpm

Do not use where _ater is microbiologiealty unsafe or _ith *rater of unknown quatit_, except that

systems certified for cyst reduction may be llsed on disinl}cted waters that may contain filterable cysts.

Reolacemenl Elemenl(s}

T1RFKB1 T1RFKB1 T1RFKB1 T1RFKB1

2,4,5-TP (Silvex) Tribromoacefic Acid

1 2.4-Trichlorobenzene

1.1 1-Tr ch oroethane .t.2-TrlcNoroelhane

Trlchtoroe_hylene I'ribalomethanes 1 l'llMa

Bronmdlchloronlethane Bromolbrm

Chloro_btm Chlorodiblomome/hane

Xylenes

Replacement Parts"

To order stainless steel cleaner or replacement filters, call

1-800-4-MY-HOME e and ask for the appropriate part number listed below or contact your authorized Kenmore dealer.

Stainless Steel Cleaner and Polish: Order Part #D22 M40083 R

Base Grille Water Filter: Replacement Filter:

Order Part #9030 (T1RFKB2 or T1RFKB1 or P1RFKB2 or P1RFKB1)

In Canada, Order Part #9030B (T1RFKB2 or T1RFKB1 or P1RFKB2 or P1RFKB1)

+ 56 hidden pages