Kenmore HD-950 User Manual

Installation and Operating Instructions

NOTE: This filter housing does not include a filter cartridge. Choose the appropriate filter cartridge for your needs and install in housing according

to the Cartridge Replacement instructions before proceeding with installation. See cartridge selection chart.

Operating Specifications

Pressure Range: 30–100 psi (2.1–6.9 bar) Temperature Range: 40–100°F (4.4–37.7°C)

Parts Included

Filter Housing Housing Wrench

Precautions

WARNING: Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after the system.

CAUTION: Filter must be protected against freezing, which can cause cracking of

the filter and water leakage.

CAUTION: The rubber O-ring provides the water-tight seal between the cap and

the bottom of the housing. It is important that the O-ring be properlyseated in the groove above the threads of the housing or a water leak could occur.

CAUTION: Because of the product’s limited service life and to prevent costly

repairs or possible water damage, we strongly recommend that the bottom of all plastic housings be replaced every ten years. If the bottom of your housing has been in use for longer than this period, it should be replaced immediately. Date the bottom of any new or replacement housing to indicate the next recommended replacement date.

NOTE:

• For cold water use only.

• Make certain that installation complies with all state and local laws and regulations.

• The contaminants or other substances removed or reduced by the selected cartridge are not necessarily in your water. Ask your local water municipality for a copy of their water analysis, or have your water tested by a reputable water testing lab.

• After prolonged periods of non-use (such as during a vacation) it is recommended that the system be flushed thoroughly. Let water run for 5–6 minutes before using.

• The filter cartridge used with this system has a limited service life. Changes in taste, odor, color, and/or flow of the water being filtered indicate that the cartridge should be replaced.

• Some harmless bacteria may attack cellulose media cartridges. The CP5-BBS is not recommended on non-chlorinated water. If your cartridge seems to disintegrate or develops a musty or moldy odor, switch to a synthetic media cartridge or consult the manufacturer.

Heavy Duty Water Filter Model HD-950

Tested and Certified by NSF International to NSF/ANSI Standard 42 with cartridge RFC-BBS. See Performance Data Sheet in Manual for specific claims.

Technical Support: 1-800-645-5426

(M-F 7:30 am - 5:00 pm CST)

145054 Rev G11/03

Tools Required

•2 adjustable wrenches • File

• 2 Pipe Wrenches • Pencil

• Pipe threader • Pipe Cutter or Hacksaw

Materials Required (not included)

Depends on type, size, and location of pipe on which filter will be installed. Measure the pipe to determine what size nipples, union, and valve you will need. If you are not installing on 1-inch pipe, you will also need to purchase the appropriate size bushings. Consult your local hardware store to learn more about your particular installation needs.

NOTE: Galvanized fittings must be used with galvanized pipe.

Optional Materials

•150456 WBA Mounting Bracket

•Jumper Wire (See your Local Dealer)

Installation

NOTE:

• Please read all instructions, specifications, and precautions before installing and using your water filter.

• Install filter cartridge in housing before proceeding with installation (see Filter Cartridge Replacement on page 3).

• Install filter after water meter or pressure tank.

• Numbered diagrams correspond with numbered steps.

1. Apply about 12 inches (300 mm) of Teflon® tape in clockwise direction to pipe threads of each fitting.

2. If mounting bracket (not supplied) is to be used, attach to cap before assembling the fittings. NOTE: Allow 1-1/2 inches (33 mm) clearance below housing to enable filter cartridge

changes.

3. Assemble all fittings. Start adapters into cap by hand. Use a wrench to tighten firmly. DO NOT OVER-TIGHTEN.

4. Measure length (shown as X on diagram) across assembled fittings and subtract 1 inch (25 mm) if you are installing on 3/4 inch (19 mm) pipe, or 1-1/2 inches (38 mm) if you are installing on 1 inch (25 mm) pipe. Mark section of pipe to be removed.

5. Using a pipe cutter or hacksaw, remove marked section of pipe and thread remaining ends. Wrap threads with Teflon tape.

6. Align filter assembly with ends of pipe, making certain cap opening marked “IN” is facing the incoming water supply. It will be necessary to spread ends of pipe apart to install filter assembly. Using two adjustable wrenches, hold incoming adapter securely with one wrench and tighten nut with second wrench. Repeat procedure for outgoing adapter.

CAUTION: If water pipes are used to ground electrical systems, appliances, or phones, be

certain to install a jumper wire. Contact your local electrician for more information. (Diagram 6)

Slowly turn on water supply to filter and depress red pressure-relief button on cap to release trapped air. Check for leaks. Open nearest faucet and flush filter for 10 minutes, wait one hour, then flush again for 10 minutes.

Troubleshooting

Leaks between cap and bottom of housing:

1. Turn off water supply and depress pressure-relief button.

2. Clean and lubricate O-ring with silicone grease. Also, clean the groove where the o-ring seats. Replace o-ring back in groove above threads. Screw bottom of housing back on cap securely by hand. Do not overtighten.

3. Turn on water supply. If leaks persist, or if there are other leaks on the system, turn off water supply. Call Technical Support at 1-800-645-5426.

Leaks on inlet/outlet connections:

1. Turn off water supply. For brass fittings, tighten nut 1/2-turn with wrench.

2. Turn on water supply. If leaks persist, or if there are other leaks on system, turn off water supply. Call Technical Support at 1-800-645-5426.

Replacement Parts

1 151039 Pressure-relief Assembly 2 154531 Cap, 1” HFPP Blue 3 151122 Oring (OR-100) 4 153029 Heavy Duty Blue Housing 5 150296 SW-3 Housing Wrench For replacement parts, contact your nearest retailer or call Culligan Consumer Services @ 1-888-777-7962. The HD-950 is covered by a limited five year warranty. See warranty for details.

Cartridge Replacement

A. Turn off water supply to filter. Depress red pressure-relief button on top of filter. Use

wrench to unscrew bottom of housing.

NOTE: If turning off water supply to filter will also turn off water supply to the rest of the home, be sure to fill a bucket of water first to allow you to clean housing after it has been removed.

B. Locate and remove large O-ring, wipe clean of lubricant and set aside. Discard used

cartridge. Rinse out bottom of housing and fill about 1/3 full with water. Add about 2 tablespoons of bleach and scrub cap and bottom of housing with nonabrasive sponge or cloth. Rinse thoroughly. Lubricate O-ring with clean silicone grease. Insert O-ring back into groove and smooth into place with finger. Insert new cartridge over standpipe in bottom of housing.

C. Screw bottom of housing onto the cap and hand-tighten. DO NOT OVER-TIGHTEN.

Turn on water supply slowly to allow filter to fill with water. Depress red pressure-relief button to release trapped air. Check for leaks before leaving installation.

NOTE: After installation, flush the cartridge for 10 minutes, wait one hour, then flush again for 10 minutes before using the water.

2 3

+ 5 hidden pages