Kenmore FREESTANDING ELECTRIC RANGE WITH DOUBLE OVENS Installation Instructions Manual

INSTALLATIONINSTRUCTIONS

FREESTANDINGELECTRICRANGE WITH DOUBLEOVENS

TableofContents

RANGE SAFETY ............................................................................. 1

INSTALLATION REQUIREMENTS ................................................ 2

Tools and Parts ............................................................................ 2

Location Requirements ............................................................... 2

Electrical Requirements ............................................................... 4

INSTALLATION INSTRUCTIONS .................................................. 5

Unpack Range ............................................................................. 5

Adjust Leveling Legs .................................................................... 5

Install Anti-Tip Bracket ................................................................ 5

Electrical Connection ................................................................... 6

Verify Anti-Tip Bracket Location ................................................ 11

Level Range ............................................................................... 11

Complete Installation ................................................................. 11

Moving the Range ..................................................................... 12

RANGESAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow
instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

iMPORTANT:

Save for local electrical inspector's use.

W10160642A

A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.

1.__ l Tip Over Hazard

Reconnect the anti=tip bracket, if the range is moved.
Failure to follow these instructions can result in death or serious burns to children and adults.

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed

here.

Tools needed

• Tape measure •

• Level •

• Phillips screwdriver •

• Flat-blade screwdriver •

Parts supplied

Check that all parts are included.

3 - 10-32 hex nuts (attached to terminal block)
3 - Terminal lugs

Oven racks
2 - #12 x 1%" screws (for mounting anti-tip bracket)

Anti-tip bracket (taped inside upper oven with literature
package)

Anti-tip bracket must be securely mounted to back wall or
floor. Thickness of floor may require longer screws to anchor

bracket to sub-floor. Longer screws are available from your
local hardware store.

Parts needed
If using a power supply cord:

• A UL listed power supply cord kit marked for use with ranges.
The cord should be rated at 250 volts minimum, 40 amps or
50 amps that is marked for use with nominal 1%" (3.5 cm)

diameter connection opening and must end in ring terminals
or open-end spade terminals with upturned ends.

• A UL listed strain relief.

Check local codes. Check existing electrical supply. See
"Electrical Requirements" section.

It is recommended that all electrical connections should be made
by a licensed, qualified electrical installer.

Wrench or pliers
%" nut driver

Hand or electric drill
1/8"(3.2 mm) drill bit

IMPORTANT: Observe all governing codes and ordinances.

• It is the installer's responsibility to comply with installation
clearances specified on the model/serial rating plate. The
model/serial rating plate is located behind the control panel.

• The range should be located for convenient use in the
kitchen.

To eliminate the risk of burns or fire by reaching over heated
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood
that projects horizontally a minimum of 5" (12.7 cm) beyond

the bottom of the cabinets.

• Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.

• The floor anti-tip bracket must be installed. To install the anti-
tip bracket shipped with the range, see "Install Anti-Tip
Bracket" section.

• Grounded electrical supply is required. See "Electrical
Requirements" section.

IMPORTANT: To avoid damage to your cabinets, check with your
builder or cabinet supplier to make sure that the materials used

will not discolor, delaminate or sustain other damage. This range
has been designed in accordance with the requirements of UL
and CSA International and complies with the maximum allowable
wood cabinet temperatures of 194°F (90°C).

Mobile Home - Additional Installation Requirements
The installation of this range must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280). When such standard is not
applicable, the Standard for Manufactured Home Installations,

ANSI A225.1/NFPA 501A or with local codes.
Mobile home installations require:

• When this range is installed in a mobile home, it must be
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the standards

listed above.

• Four-wire power supply cord or cable must be used in a
mobile home installation. The appliance wiring will need to be

revised. See "Electrical Connection" section.

Product Dimensions

A

Cabinet Dimensions

Cabinet opening dimensions shown are for 25" (64 cm)
countertop depth, 24" (61 cm) base cabinet depth and
36" (91.4 cm) countertop height.

If installing a range hood or microwave hood combination above
the range, follow the range hood or microwave hood combination

installation instructions for dimensional clearances above the
cooktop surface.

A freestanding range may be installed next to combustible walls
with zero clearance.

b

A. 467/8'' (119.9 cm)
B. Model/serial number plate

(located behind the control

panel) *

C. 357/8'' (91.4 cm)
D. 297/8'' (75.9 cm)
E. 26%6"-27¼" (66.8- 69.2 cm)**

*Serial number plate may be rotated up from behind the control

panel for viewing from the front of the range.

**Excludes handle. Dimension given is from wall to front of oven

door and will vary based on electric outlet receptacle
installation.

H

A. 13" (33 cm) upper cabinet

depth

B. 30" (76.2 cm) min. opening

width

C. For minimum clearance to the

top of the cooktop,
see NOTE.

D. 30" (76.2 cm) min. opening

width

E. Cabinet door or hinge should

not extend into cutouL

F. 3-wire shaded area* -

7" (17.8 cm) min. from left
side cabinet, 53/4" (14.6 cm)
max. from floor, 6" (15.2 cm)

max. width

G. 4-wire shaded area* -

10" (25.4 cm) min. from right
side cabinet, 53_ '' (14.6 cm)
max. from floor, 6" (15.2 cm)

max. width
*Nothing located in shaded

areas can extend more than

!_±" (3.8 cm) from waft or

range will not slide all the way
back.

H. 17/2'' (3.8 cm) min. from floor if

using a flush mount outlet.

NOTE: 24" (61 cm) minimum when bottom of wood or metal
cabinet is protected by not less than 1/4"(0.64 cm) flame retardant
millboard covered with not less than No. 28 MSG sheet steel,

0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or

0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking

platform and the bottom of an unprotected wood or metal
cabinet.

Ifcodespermitandaseparategroundwireisused,itis
recommendedthataqualifiedelectricalinstallerdeterminethat
thegroundpathandwiregaugeareinaccordancewithlocal

codes.
Donotuseanextensioncord.

Besurethattheelectricalconnectionandwiresizeareadequate
andinconformancewiththeNationalElectricalCode,ANSI/

NFPA70-latesteditionandalllocalcodesandordinances.

Acopyoftheabovecodestandardscanbeobtainedfrom:

NationalFireProtectionAssociation

OneBatterymarchPark

Quincy,MA02269.

WARNING:Improperconnectionoftheequipment-grounding
conductorcanresultinariskofelectricshock.Checkwitha

qualifiedelectricianorservicetechnicianifyouareindoubtasto
whethertheapplianceisproperlygrounded.Donotmodifythe
powersupplycordplug.Ifitwillnotfittheoutlet,haveaproper
outletinstalledbyaqualifiedelectrician.

Electrical Connection

To properly install your range, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.

• Range must be connected to the proper electrical voltage
and frequency as specified on the model/serial number rating
plate. The model/serial number rating plate is located behind
the control panel or on the oven frame behind the storage
drawer panel. Refer to the figures in the "Product
Dimensions" section of the "Location Requirements" section.

• This range is manufactured with the neutral terminal
connected to the cabinet. Use a 3-wire, UL listed, 40- or
50-amp power supply cord (pigtail) (see Range Rating chart
below). If local codes do not permit ground through the
neutral, use a 4-wire power supply cord rated at 250 volts,
40 or 50 amps and investigated for use with ranges.

Range Rating* Specified Rating of

Power Supply Cord Kit

and Circuit Protection

120/240 Volts 120/208 Volts Amps

8.8 - 16.5 KW 7.8 - 12.5 KW 40 or 50**

16.6 - 22.5 KW 12.6 - 18.5 KW 50

If connecting to a 4-wire system:
This range is manufactured with the ground connected to the

cabinet. The ground must be revised so the green ground wire of
the 4-wire power supply cord is connected to the cabinet. See

"Electrical Connection."
Grounding through the neutral conductor is prohibited for new

branch-circuit installations (1996 NEC); mobile homes; and
recreational vehicles, or an area where local codes prohibit
grounding through the neutral conductor.

When a 4-wire receptacle of NEMA Type 14-50R is used, a
matching UL listed, 4-wire, 250-volt, 40- or 50-amp, range power
supply cord (pigtail) must be used. This cord contains 4 copper
conductors with ring terminals or open-end spade terminals with
upturned ends, terminating in a NEMA Type 14-50R plug on the
supply end.

The fourth (grounding) conductor must be identified by a green or
green/yellow cover and the neutral conductor by a white cover.
Cord should be Type SRD or SRDT with a UL listed strain relief
and be at least 4 ft (1.22 m) long.

@

4-wire receptacle (14-50R)

The minimum conductor sized for the copper 4-wire power
cord are:

40-amp circuit
2 No.-8 conductors

1 No.-10 white neutral
1 No.-8 green grounding

If connecting to a 3-wire system:
Local codes may permit the use of a UL listed, 3-wire, 250-volt,

40- or 50-amp range power supply cord (pigtail). This cord
contains 3 copper conductors with ring terminals or open-end
spade terminals with upturned ends, terminating in a NEMA Type
10-50P plug on the supply end. Connectors on the appliance end
must be provided at the point the power supply cord enters the
appliance. This uses a 3-wire receptacle of NEMA Type 10-50R.

*The NEC calculated load is less than the total connected load

listed on the model/serial rating plate.

**If connecting to a 50-amp circuit, use a 50-amp rated cord with

kit. For 50-amp rated cord kits, use kits that specify use with a
nominal 1%" (34.9 mm) diameter connection opening.

• A time-delay fuse or circuit breaker is recommended.
The range can be connected directly to the fused disconnect

(or circuit breaker box) through flexible or nonmetallic
sheathed, copper or aluminum cable. See "Electrical

Connection."

• Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack in the line so that
the range can be moved if servicing is ever necessary.

• A UL listed conduit connector must be provided at each end
of the power supply cable (at the range and at the junction
box).

• Wire sizes and connections must conform with the rating of
the range.

• The wiring diagram is located on the back of the range or
inside the storage drawer in a clear plastic bag.

3-wire receptacle (10-50R)

INSTALLATIONINSTRUCTIONS

U " pcsck

Excessive Weight Hazard

Use two or more people to move and install range.
Failure to do so can result in back or other injury.

1. Remove shipping materials, tape and protective film from the
range. Keep cardboard bottom under range.

2. Remove oven racks and parts package from inside oven.

3. To place range on its back, take 4 cardboard corners from the
carton. Stack one cardboard corner on top of another.
Repeat with the other 2 corners. Place them lengthwise on
the floor behind the range to support the range when it is laid

on its back.

4. Using 2 or more people, firmly grasp the range and gently lay
it on its back on the cardboard corners.

5. Pull cardboard bottom firmly to remove.

6. Use an adjustable wrench to loosen the leveling legs.

7. Place cardboard or hardboard in front of range. Using 2 or
more people, stand range back up onto cardboard or

hardboard.

NOTE: If height adjustment is made when range is standing,
tilt the range back to adjust the front legs, then tilt forward to
adjust the rear legs.

3,

When the range is at the correct height, check that there is
adequate clearance under the range for the anti-tip bracket.
Before sliding range into its final position, check that the anti-
tip bracket will slide under the range and onto the rear
leveling leg prior to anti-tip bracket installation.

f,

Remove the anti-tip bracket that is taped inside the upper
oven with the literature package.

2.

Determine which mounting method to use: floor or wall.
If you have a stone or masonry floor you can use the wall

mounting method.

3,

Determine and mark edge of range in the cutout space. The
mounting bracket can be installed on either the left side or
right side of the cutout. Position mounting bracket in cutout
so that right (or left) edge of the bracket is _sAd'(2.4 cm) from
the marked edge of the range, as shown.

A

...........I

f. If range height adjustment is necessary, use a wrench or

pliers to loosen the 4 leveling legs.
This may be done with the range on its back or with the range

supported on 2 legs after the range has been placed back to
a standing position.

NOTE: To place range back up into a standing position, put a
sheet of cardboard or hardboard in front of range. Using 2 or
more people, stand range back up onto the cardboard or

hardboard,

Tip Over Hazard

A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.
Failure to follow these instructions can result in death

or serious burns to children and adults.

A. Anti-tip bracket
B. Mark edge of range
C. ls/_6"(2.4 cm)

2,

Adjust the leveling legs to the correct height. Leveling legs
can be loosened to add up to a maximum of 1" (2.5 cm). A
minimum of SAd'(5 mm) is needed to engage the anti-tip

bracket.

4. Drilltwo1/8"(3mm)holesthatcorrespondtothebracket
holesofthedeterminedmountingmethod.Seebelow.

Floor Mounting

A B

A. #12 x 1%" screws

B.Anti-tip bracket

Wall Mounting

A B

A. #12x 1%" screws
B.Anti-tip bracket

5=

Using the Phillips screwdriver, mount anti-tip bracket to the
wall or floor with the two #12 x 1%" screws provided.

Power Supply Cord

Electrical Shock Hazard

Disconnect power before servicing.
Use a new 40 amp power supply cord.
Plug into a grounded outlet.

Failure to follow these instructions can result in death,
fire, or electrical shock.

1. Disconnect power. 3.

2. Use Phillips screwdriver to remove the terminal block cover

screw located on the back of the range, Pull cover down and
toward you to remove cover.

Direct Wire

Electrical Shock Hazard

Disconnect power before servicing.
Use 8 gauge copper or 6 gauge aluminum wire.

Electrically ground range.
Failure to follow these instructions can result in death,

fire, or electrical shock.

Remove plastic tag holding three 10-32 hex nuts from the
middle post of the terminal block.

Addstrainrelief.

4. • Replacecord/conduitplateandinsertscrews.

Style 1: Power supply cord strain relief

• Assemble a UL listed strain relief in the opening.

A

• Assemble a UL listed conduit connector in the opening.

A. UL listed strain relief

• Feed the power supply cord through the strain relief in the

cord/conduit plate on bottom of range. Allow enough
slack to easily attach the wiring to the terminal block.

• Tighten strain relief screw against the power supply cord.

J

t

B

Style 2: Direct wire strain relief

• Use Phillips screwdriver to remove screws and slide

cord/conduit plate down and out.

• Position cord/conduit plate as shown in the following

illustration.

A. Removableretaining nut

B.Strain relief

• Feed the flexible conduit through the strain relief, allowing
enough slack to easily attach wiring to the terminal block.

• Tighten strain relief screw against the flexible conduit.

5,

Replace back panel and screws on rear of range.

6.

Complete installation following instructions for your type of
electrical connection:

4-wire (recommended)
3-wire (if 4-wire is not available)

Electrical Connection Options

If your home has: And you will be Go to Section:

connecting to:

4-wire receptacle A UL listed, 4-wire connection:
(NEMA type 14-50R) 250-volt Power supply cord

40-amp, range
minimum,

power supply
cord

4-wire direct A fused 4-wire connection:

disconnect or Direct wire
circuit breaker

(12.7 crn) box

3-wire receptacle A UL listed,
(NEMA type 10-50R) 250-volt

3-wire connection:
Power supply cord

minimum,

power supply

40-amp, range
cord

3=

Feed the power supply cord through the strain relief in the
cord/conduit plate on bottom of range. Allow enough slack to
easily attach the wiring to the terminal block.

3-wire direct A fused

1" disconnect or

(2.5 crn) _ circuit breaker

3-wire connection:
Direct wire

box

4-wire connection: Power Supply Cord

Use this method for:

New branch-circuit installations (1996 NEC)
Mobile homes

Recreational vehicles
In an area where local codes prohibit grounding through the

neutral
Part of metal ground strap must be cut out and removed•

'B

A. Metal ground strap
B. Ground-link screw

2=

Use Phillips screwdriver to remove the ground-link screw
from the back of the range. Save the ground-link screw.

A. Terminalblock

B.Ground-link screw

C. Cord/conduit plate
D.Power supply cord wires

4=

Use Phillips screwdriver to connect the green ground wire
from the power supply cord to the range with the ground-link
screw. The ground wire must be attached first.

5=

Use %" nut driver to connect the neutral (white) wire to the
center terminal block post with one of the 10-32 hex nuts•

F

D

A. 10-32 hex nut
B. Ground-link screw

C• Line ! (black)

6=

Connect line 1 (black) and line 2 (red) wires to the outer

D. Green ground wire

E. Neutral (center) wire
E Line 2 (red)

terminal block posts with 10-32 hex nuts.

7.

Securely tighten hex nuts.
NOTE: For power supply cord replacement, only use a power

cord rated at 250 volts minimum, 40 amps or 50 amps that is
marked for use with nominal 1%" (3.5 cm) diameter
connection opening, with ring terminals and marked for use
with ranges.

8. Replace terminal block access cover•

3-wire connection: Power Supply Cord

Direct Wire Installation: Copper or Aluminum Wire

Use this method only if local codes permit connecting chassis
ground conductor to neutral wire of power supply cord.

1. Feed the power supply cord through the strain relief in the
cord/conduit plate on bottom of range. Allow enough slack to

easily attach the wiring to the terminal block.

A. Terminal block
B. Ground-link screw

C. Cord/conduit plate
D. Power supply cord wires

2=

Use %" nut driver to connect the neutral (white) wire to the
center terminal block post with one of the 10-32 hex nuts.

This range may be connected directly to the fuse disconnect or
circuit breaker box. Depending on your electrical supply, make
the required 3-wire or 4-wire connection.

1. Strip outer covering back 3" (7.6 cm) to expose wires. Strip
the insulation back 1" (2.5 cm) from the end of each wire.

(7.6 cm)

2. Allow enough slack in the wire to easily attach the wiring
terminal block.

3. Complete electrical connection according to your type of
electrical supply (4-wire or 3-wire connection).

4-wire Connection: Direct Wire

Use this method for:

• New branch-circuit installations (1996 NEC)

• Mobile homes

• Recreational vehicles

• In an area where local codes prohibit grounding through the
neutral

1. Part of metal ground strap must be cut out and removed.

E

A ..........

C

A. 10-32 hex nut
B.Line ! (black)

D. Neutral (white) wire

E. Line 2 (red)

C.Ground-link screw

3=

Connect line 1 (black) and line 2 (red) wires to the outer
terminal block posts with 10-32 hex nuts.

4.

Securely tighten hex nuts.
NOTE: For power supply cord replacement, only use a power

cord rated at 250 volts minimum, 40 amps or 50 amps that is
marked for use with nominal 1%" (3.5 cm) diameter

connection opening, with ring terminals and marked for use
with ranges.

5. Replace terminal block access cover.

A. Metal ground strap
B. Ground-link screw

2=

Use Phillips screwdriver to remove the ground-link screw
from the back of the range. Save the ground link screw and
discard the remaining end of the ground link.

3. Pulltheconduitthroughthestrainreliefoncord/conduitplate
onbottomofrange.Allowenoughslacktoeasilyattach
wiringtotheterminalblock.

6. Use%"nutdrivertoconnecttheneutral(white)wiretothe
centerterminalblockpostwithoneofthe10-32hexnuts.

D

F

E

A. Terminal block
B. Ground-link screw

C. Cord/conduit plate
D. Line 2 (red) wire

4.

Attach terminal lugs to line I (black), neutral (white), and line 2

E. Neutral (white) wire

F. Line ! (black) wire

G. Bare (green) ground wire

(red) wires. Loosen (do not remove) the set screw on the front
of the terminal lug and insert exposed wire end through

bottom of terminal lugs, Securely tighten set screw to XX Ibs-
in. torque. See Bare Wire Torque Specifications chart.

/ E

C

A. 10-32 hex nut
B. Line 1 (black)

C. Bare (green) ground wire
D. Ground-link screw

b

E. Neutral (white) wire
F Line 2 (red)

G. Terminal lug

7. Connect line 1 (black) and line 2 (red) wires to the outer
terminal block posts with 10-32 hex nuts.

8. Securely tighten hex nuts.

9. Replace terminal block access cover.

3-wire connection: Direct Wire

Use this method only if local codes permit connecting ground
conductor to neutral supply wire.

1. Pull the conduit through the hole and conduit plate on bottom
of range. Allow enough slack to easily attach the wiring to the

terminal block.

A. Terminal lug
B. Set screw

C. Line 1 (black) wire
D. Neutral (white) wire

E.Line 2 (red) wire

Bare Wire Torque Specifications
Attaching terminal lugs to the terminal block - 20 Ibs-in. (2.3 N-m)

Wire Awg Torque
8 gauge copper 25 Ibs-in. (2.8 N-m)

6 gauge aluminum 35 Ibs-in. (4.0 N-m)

5. Use Phillips screwdriver to connect the bare (green) ground
wire to the range with the ground-link screw. The ground wire

must be attached first and must not contact any other
terminal.

10

A. Terminal block
B. Ground-link screw

C. Cord/conduit plate

F

D. Line 2 (red) wire
E. Bare (green) ground wire
F. Line ! (black) wire

2,

Attach terminal lugs to line I (black), bare (green) ground, and
line 2 (red) wires. Loosen (do not remove) the set screw on the
front of the terminal lug and insert exposed wire end through
bottom of terminal lugs. Securely tighten set screw to XX Ibs-
in. torque. See Bare Wire Torque Specifications chart.

g
B

B

Slide range back so rear range foot is engaged with
anti-tip bracket.

C D

A. Terminal lug
B. Set screw

C. Line 1 (black) wire
D. Bare (green) ground wire

E.Line 2 (red) wire

Bare Wire Torque Specifications
Attaching terminal lugs to the terminal block - 20 Ibs-in. (2.3 N-m)

Wire Awg Torque

8 gauge copper 25 Ibs-in. (2.8 N-m)
6 gauge aluminum 35 Ibs-in. (4.0 N-m)

3. Use %" nut driver to connect the bare (green) ground wire to
the center terminal block post with one of the 10-32 hex nuts.

F

E

D

C

A. 10-32 hex nut

B. Line 1 (black)
C. Ground-link screw

D. Bare (green) ground wire

& Line 2 (red)
F. Terminal lug

4. Connect line 1 (black) and line 2 (red) wires to the outer
terminal block posts with 10-32 hex nuts.

5. Securely tighten hex nuts.

6. Replace terminal block access cover.

Making sure the anti-tip bracket is installed:

• Look for the anti-tip bracket securely attached to floor or

wall.

Place rack in oven. Place level on rack and check levelness of
range, first side to side; then front to back.

2. If range is not level, pull range forward until rear leveling leg is
removed from the anti-tip bracket.

3. Use wrench to adjust leveling legs up or down until range is
level. Push range back into position.

4. Check that rear leveling leg is engaged in anti-tip bracket.

NOTE: Range must be level for satisfactory baking conditions.

1. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check that the range is level. See "Level Range."

5. Use a mild solution of liquid household cleaner and warm
water to remove waxy residue caused by protective shipping
material. Dry thoroughly with a soft cloth. For more
information, read the "Range Care" section of the Use and

Care Guide.

6. Read the range Use and Care Guide.

7. Plug power cord into appropriate outlet. Slide range into its
final location. Check that the flexible conduit or power supply

cord are not bent.

8. Turn power on. Turn on surface burners and oven. See the
Use and Care Guide for specific instruction on range
operation.

If range does not operate, check the following:

• Household fuse is intact and tight; or circuit breaker has not
tripped.

• Range is plugged into an outlet.

• Electrical supply is connected.

• See "Troubleshooting" inthe Use and Care Guide.
When the range has been on for 5 minutes, check for heat. If

range is cold, turn off the range and contact a qualified
technician.

11

For direct-wired ranges:

Tip Over Hazard

A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.
Failure to fellow these instructions can result in death

or serious burns to children and adults.

When moving range, slide range onto cardboard or hardboard to
avoid damaging the floor covering.

If removing the range is necessary for cleaning or maintenance:

For power supply cord-connected ranges:

1. Slide range forward.

2. Unplug the power supply cord.

3. Complete cleaning or maintenance.

4. Plug in power supply cord.

5. Check that anti-tip bracket is installed:

• Look for the anti-tip bracket securely attached to floor or
wall.

• Slide range back so rear range foot is under anti-tip
bracket.

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.

1. Disconnect power.

2. Slide range forward.

3. Complete cleaning or maintenance.

4. Check that anti-tip bracket is installed:

• Look for the anti-tip bracket securely attached to floor or
wall.

• Slide range back so rear range foot is under anti-tip
bracket.

5.

Reconnect power.

6.

Check that range is level.

6.

Check that range is level.

W10160642A

© 2007. Whirlpool Corporation,
All rights reserved.

Printed in U.S.A.

10/07