Kenmore Elite 233.55229000, Elite 233.55224000, Elite 233.55223000, Elite 233.55129000, Elite 233.55124000 User Manual

...

ange

Use & Care / installation Manual

cocina

Manual de use y cuidado /instalaci6n

Models Modelos

233.55022000 (30" wide = White)

233.55023000 (30" wide =Stainless)

233.55024000 (30" wide =Biscuit)

233.55027000 (30" wide =Almond)

233.55029000 (30" wide =Black)

233.55222000 (42" wide = White)

233.55223000 (42" wide = Stainless)

233.55224000 (42" wide = Biscuit)

233.55227000 (42" wide =Almond)

233.55229000 (42" wide = Black)

233.55122000 (36" wide = White)

233.55123000 (36" wide = Stainless)

233.55124000 (36" wide =Biscuit)

233.55127000 (36" wide =Almond)

233.55129000 (36" wide = Black)

Patent No,:

US D450,829 S

626989A Sears, Roebuck and Co,, Hoffman Estates, UL60179 U,S,A, www,sears,com

SECTION ...................................................................... PAGE

Warranty .............................................................................. 2

Safety Instructions ............................................................... 2

Operation ............................................................................. 3

Cleaning ............................................................................... 3

Parts Included With Hood .................................................... 4

Parts Not Included With Hood ............................................. 4

Tools Needed ....................................................................... 4

Equivalent Duct Length Chart ............................................. 5

Prepare The Hood Location ................................................ 6

Prepare The Hood ....................................................... 7, 8, 9

Connect The Wiring ........................................................... 10

install The Hood ................................................................. 11

Service Parts ..................................................................... 12

if within 1 year from the date of installation, any part of this range hood fails to function properly due to a defect in mate-

rial or workmanship, Sears will repair the part or furnish and install a new part, free of charge.

FULL 30-DAY WARRANTY ON FINISH ON PAINTED OR BRIGHT METAL PARTS

if within 30 days from the date of installation, the finish on any painted or bright metal parts of this range hood is defective in

materia! or workmanship, Sears will furnish and install a new part, free of charge.

WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEAREST SEARS SEWCE CENTER/DEPART_,'IENT

_NTHE UNITED STATES,

This warranty applies only while this product is in use in the

United States. This warranty gives you specific legal rights and

you may have other rights which vary from state to state. Sears, Roebuck and Co., Dept 817WA, Hoffman Estates,

IL 6017

iNTENDED FOR DOMESTIC COOKING ONLY

FOR RESJ[:)ENTJAL USE ONLY

WARNmNGA A WARNmNGA A

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufac- turer. If you have questions, contact the manufacturer at

the address listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the

service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the

service panel.

3. installation work and electrical wiring must be done by a qualified person(s)in accordance with all applicable codes

and standards, including fire-rated codes and standards.

4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Fo!low the heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), and the American Society

for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

5. When cutting or drilling into wail or ceiling, do not damage electrical wiring and other hidden utilities.

6. To reduce the risk of fire or electric shock, do not use this

range hood with an additional speed control device.

7. Ducted fans must always be vented to the outdoors.

8. To reduce the risk of fire, use only metal ductwork.

9. Use with approved cord-connection kit only only.

10.This unit must be grounded.

TO REDUCE THE RiSK OF A RANGE TOP GREASE FIRE:

1. Never leave surface units unattended at high settings,

Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or when cooking flaming foods.

3. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

4. Use proper pan size. Always use cookware appropriate for the size of the surface element. 2

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE

FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. if the flames do not go out immediately, EVACUATE AND CALL THE FiRE DEPARTMENT.

2. NEVER PiCK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will result.

4. Use an extinguisher ONLY if: A. You know you have a Class ABC extinguisher and you

already know how to operate it.

B. The fire is small and contained in the area where it

started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

* Based on "Kitchen Firesafety Tips" published by NFPA.

CAUTION A

1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust,

etc. off power unit.

3. For best capture of cooking impurities, your range hood

should be mounted so that the top of the hood is 24-30" above the cooking surface.

4. Use only with range hood cord-connection kits that have been investigated and found acceptable for use with this

model range hood.

5. Please read specification label on product for further information and requirements.

hood is to be installed Non-Ducted:

Purchase a set of (2) non-ducted filters from your mocatdistributor or retailer and attach them to the

aluminum mesh fHtereo

I_N Lm_T

Fan and Lights 3 push button switches for each. Push any button to select one of 3fan speeds

or one of 3 light levels. Push the same button to turn fan or light off. Press another button to change fan speed or light level. A light above each fan button indicates the fan speed.

Heat Sentry Your range hood is equipped with the Heat Sentry feature, which monitors

temperature. The Heat Sentry wilI automatically turn the fan on at its highest speed when the temperature is above normal.

1) If a fan setting is selected when the Heat Sentry in on, the light above the fan button will flash on and off.

2) If the fan setting is off when the Heat Sentry is on, the light above fan button 3 will flash on and off rapidly.

After the temperature has lowered to normal, the fan will change to the setting prior to the Heat Sentry turning on.

Fuee

The hood control contains a fuse to protect it from power surges_ If the fuse has opened (blown), the green fan-Ievel indicators wilI operate properly when

the fan buttons/switches are pressed - but the fan and lights will not turn on. The fuse is a 5 x 20 ram, 10 Amp, Fast-Acting, 125V (rain.). Common manufac-

turer and part numbers are: Littlefuse, 217010; Bussmann, GMA10A; Wickmann, 1942100. Radio Shack, Digikey (1-800-344-4539), and most elec- tronic supply stores have them in stock.

To replace the fuse:

1. Disconnect power at service entrance.

2. Remove filters, bottom panel, light wire harness, and air chute.

3. Remove and inspect fuse. If it is not open (blown), additional diagnostics need to be done.

4. Instal! new fuse.

5. Re-assemble air chute, light wire harness, bottom panel, and filters.

6. Turn on power and check hood/control operation.

NomDucted Operation Purchase a set of CIean Cooking Filters and attach them to the aluminum

mesh fiIters. See page 4 for Clean Cooking Filter information.

CIean Cooking Filters availabIe by calIing Sears at 1-800-4-MY-HOME ® NOTE: For models that are installed in the non-ducted mode, the most

effective operation is achieved at speeds 1 and 2. These speeds

provide the most efficient and quiet operation during cooking, while maximizing the benefits of the recircuiating filtration system.

etectric shock, disconnect from

WARNING: To reduce the risk of

power suppmy before cleaning,

Amuminum mesh filters Clean frequently using hot water and a mild

detergent or in your dishwashen The alumi- num mesh filters should be washed approxi-

mately every month depending on the amount of usage. Wash more often if your

cooking style generates greater grease - like frying foods or wok cooking.

Non-ducted filters (Cmean Cooking hoods only)

(available separately - see page 4)

Clean filter surfaces frequently with a damp cloth and a mild detergent. DO NOT im-

merse filters in water or put in dishwasher. The special "Clean Sense" feature indicates

when the filter is to be replaced. The blue and yellow strips wilI blend to green when it

is time to change the filter. The "Clean Sense" feature works best when facing toward the

cooking surface.

Painted hood surfaces Wiping reguIarly with mild soap/detergent

and warm water should protect painted hood surfaces. Be cautious about using "New and

Improved" cleaning agents. Your hood is in- stalled over hot cooking equipment. Most

chemicals found in cleaning agents react with heat to loosen paint.

Stainless steel hood surfaces StainIess steel hoods should be washed

regularly with a clean cloth, warm water and mild soap or dish detergent. Clean in the di-

rection of the polish Iines. Rinse wel! with clear water and wipe dry immediately. You

may wish to apply Iight oil used for furniture polishing to emphasize it's bright finish.

Teflon ®hood surfaces Do not use abrasive cIoth, steet wool pads,

or scouring powder on the Tefion®-coated bottom cover or on any painted surface.

Fan assembBy Fan blade can be cleaned with a damp cloth

and mild detergent. Use care when clean- ing fan blade - it must not become bent or

misaligned. DO NOT ALLOW WATER TO ENTER MOTOR. Make sure all surfaces are

completely dry before re-installing filters and restoring power.

Motor is permanently lubricated. Do not oil or disassemble motor.

¢e

Teflon_ is a registered trademark of DuPont.

7-inch Round Duct Adapter

Light Bumb (2 per hood) Sears Part No, 57853

3_A" × 10"

DamperlDuct Connector

Aluminum Grease Filter (2 per hood)

(4 hood mounting screws inside)

Parts Bag

OPTmONAL PARTS (purchase separately)

Clean Cooking Filters

(Non-ducted hoods only) (2 per hood)

Sears Part Nos, 50191 (30")

50192 (36") 50193 (42")

7-inch Round Damper (For use with 7-inch Round Duct)

Sears Part No, 59183

Splashplate Sears Part Nos,

58120 30" Black/Biscuit 58128 30" White/Almond 58130 36" Black/Biscuit

58138 36" White/Almond

Cord Kit (Allows hood to be plugged into a

standard 120 VAC wall outlet)

Sears Part No, 233,22HCK44D

Ducting Accessories (See "Equivalent Duct Length Chart" on page 5 for Ducting Accessory Model Nos.

"Parts Not included With Hood" availabme by calming |

Sears at I=800=4=MY-HOME _

/ / Q /

Screwdriver Tape !/4"

(Fiat & Phillips) Pencil Measure Nutdriver

Sabre Keyhome Wire

Drill Saw -or- Saw Duct Tape Stripper

KenmorerangehoodsaredesignedtoperformefficientlywhenattachedtoIongrunsofduct.Asapointofreference,thishood wilIfunctionatapproximately80%ofitsratedairflowwhen200equivalent feet of 7" round ductwork is attached. Use this chart to

calculate the equivaIent duct length of your system.

Broan Modem401

Straight Duct

3¼qn. x 10=in. x 2-ft, long

Equivalent length

2ft.

Broan Modem406

Straight Duct

6=in° round × 2-ft. mong

Equivalent length

2 ft.

Broan Model 407

Straight Duct

7=in, round × 2-fto mong

Equivalent length

2 ft.

6qn, Round Elbow

Broan Modem419

Equivalent length

8 ft.

Broan ModeB 428

3¼=in. x 10-in.

Right-angle Elbow

Equivalent length

8.5 ft.

3¼qn° × 10=in,

D Broan Model 429

Right-angBe Fiat EBbow

Equivalent length

24 ft.

Broan IVlodet430

3¼-in° x 10-in,

Right-angme

Short

Eave Elbow

quivalent [ength

15 ft.

Broan Model 431

3¼qn. x 10-in.

Right-angle

Long

Eave E_bow

quivalent length

15 ft.

6=in. Round

Wall Cap

_ Sears ModeB 59691

Equivalent length

34 ft.

(6-fL w/o damper)

7=in. Round

WalmCap

(_ Broan Modem647

EquivaIent Iength

34 ft.

(6-fL w/o damper)

Sears Modet

59391

3¼qn. x

10-in.

Wall Cap

Equivalent

length

45 ft.

(7-ft= w/o damper)

Model 59091

Roof Cap

(accepts 7=in° round

or 3¼=in, x 10-in. duct)

Equivalent length

30 ft. (7-ft= w/o damper)

¢b

7qn, Round Elbow

Broan Modem415

Equivalent length

8 ft.

3¼-in° × 10-in. to

6=in°Round Transition

Sears Model 59581

Equivalent length

5.5 ft.

3¼=in. × !0=in. to

7=in. Round

Broan Model 412H

Transition

Equivalent Iength

5.5 ft.

Sears Modem "Ducting Accessories" available by calling:

Sears at 1-80O-4-MY-HOME e_

Broan Modet "Ducting Accessories" available by calling:

1_800=558-1711.

{b _b

1. Determine whether hood will discharge vertically (3¼" x 10" or 7" Round), horizontally (3V4"x 10" only) or non-ducted.

For vertical or horizontal discharge, run ductwork between

the hood location and a roof cap or wall cap.

For best results, use a minimum number of transitions and

elbows.

2. Use these diagrams for proper placement of ductwork and electrical cutout in cabinet or wail.

For a non-ducted installation, DO NOT cut a duct access hole.

ROOF CAP

24" - 30" ABOVE

COOKINGSURFACE

HOOD MOUNTING SCREWS (4)

31A'X 10" or 7" ROUND

For vertical discharge)

HOUSE WIRING

or Back of hood)

3W' X 10" DUCT (For horizontal discharge)

3. Run house wiring between service panel and hood

location.

7" ROUND

HOOD MOUNTING SCREWS (4) [VERTICAL DUCTING 1

1315/!6" (30" hood)

(36" hood)

WOOD SHIMS t ELECTRmCAL

(recessed°bottom CENTER (in cabinet bottom)

cabinets onmy) LiNE

ACCESS HOLE

f t ,_ ELECTRm(;AL

ACCESS HOLE

WOOD SHIMS CENTER (in cabinet bottom)

(recessed-bottom L|NE

cabinets only)

WOOD SHIMS

(recessed-bottom

cabinets only)

1" 1615/16 (db"nooo_ 1 1 ....

HOOD1915/16"(42" hood) t 1 915/16" (42" hood)

CAB|NET FRONT

_UU" nooo_ ._4_1315/16

.... (30" hood)--'_ /

I 16 5/16 (36 hood)

ELECTRICAL

MOUNTmNG CENTER ACCESS HOLE

SCREWS (4) L|NE (in walm)

Remove 7" Round Duct PBate from top of hood. Set duct plate aside - with mounting screws.

Remove tape holding FHters in place. Pull down on filter

tabs and lift filters out. Set filters aside.

7"ROUND

DUCTPLATE

FILTERS

3. Remove Teflone_-coated bottom cover from hood. Set cover and mounting screws aside.

4. Remove Damper/Duct Connector from inside the hood, Set connector aside - with mounting screws and parts

bag.

TEFLON_-

BOTTOM

COVER

(Held in

place with

2 screws)

DAMPER/

DUCT

CONNECTOR

{b _b

Teflon e_is a registered trademark of DuPonL 7

5.Removeeithertoporbackwiringknockoutandinstall approvedEmectrica_CabmeCmamp.

tf hood is to be installed Non-Ducted:

e Purchase a set of CmeanCooking FHters and attach

them to the aBuminum mesh fHterso

e Skip to Step 15or_ Page 10.

See page 4 for Clean Cooking FHter information.

CmeanCooking Filters avaimable by caning Sears

at 1-800=4_MY=NOME _

ELECTRICAL

CABLE CLAMP

The renewing Steps (6 thru 14) are fer DUCTED INSTALLATION ONLY.

6. Remove _ PaneB -held in place with (3) #8 screws

and (2) #8 screws, Disconnect light assembly wire har- ness (white connector).

Remove Air Chute -held in place with one (1) screw. NOTE: Be careful not to disconnect any wires.

AIR CHUTE

(3) #8 SCREWS MGHT

PANEL

8. Remove Baffle from air chute.

BAFFLE

+ 16 hidden pages