Assembly Instructions
Liquid Propane Gas Grill
Models: 920.16201, 920.16203
EngineeringCodes:KCKt1645- KCK11625
No Tools Required
FLAVOR
/'_ CAUTION:
Assemblerllnstallerleavetheseinstructions
withthe consumer.
Consumer/Userreadall theseinstructions
and keepthem ina safe placeforfuture
reference.
Sears, RoebuckandCo.,Hoffman Estates,IL 60179U.S.A.
114122420209
• Easy Assembly Instructions
• Important Warranty Information
• Safety and Maintenance Tips
/_WARNING:
Units not equipped with a side burner
CANNOT BE converted to a Side
Burner unit. If a conversion is attempted
the warranty will be voidr
Table of Contents Page
Hazard Statements ............... 2
Hardware ...................... 2
Product Packaging ............... 3
Assembly Instructions .......... 4-13
Parts Diagram ................. 14
Parts List ..................... 15
Before Use Information ........... 15
Service Numbers ........ Back Cover
Hardware
DU
Frame
(10)
(32500198)
1/4-20X 2"
CarriageBolt
Hazard Statements
//_ WARNING:
The edges of sheet metal parts can cause
injury if not handled with care.
USE EXTREME CAUTION!
,_k WARNING:
Combustion by-products produced when
using this product contains chemicals
known to the State of California to cause
cancer, birth defects, or other reproductive
harm.
Z_ WARNING:
To ensure proper gas flow, burner control
valves must be "OFF" before opening the
gas cylinder valve.
//_ WARNING:
Units not equipped with a side burner
CANNOT BE converted to a Side Burner
unit. If a conversion is attempted the
warranty will be void!
/'_ IMPORTANT:
Your grill may not have all the parts
shown. Please refer to the back of these
instructions for a listing of parts for your
specific model of grill.
Front Basket
Assembly for
Model
920.16203
DM
(2)
(32500197)
10-24x I 3/4
CarriageBolt
Frame
Front
Handle
Assembly
Z) (10)
(32500179) (00402371)
10-24x3/4 114-20
CarriageBolt StarWasher
Grill Lid and Burner
132300112)
Hinge Pin T (00402507)
Frame Front Handle
Assembly and Front Basket
Assembly
Grill Lid
Assembly
NO
Assembly
DZ
MR
HairPin
11412242 (rig. 2)
(10) (4)
(32700101) (32700132)
114-20 t0-24
Wing Nut WingNut
Carton Contents
Note: not all parts are shown in
illustration.
Model920.16201
1AssemblyInstruction
UseandCare Manual
HardwarePackage(seepage2, Hardware)
IgniterPackage
LargeHardwarePackage
FrameKitBox
BaseAssembly
ControlPanelAssembly
HeatShield
BottomCasting
TopCasting
Burner
Handle
HeatTent
CookingGrid
BottomWarmingRack
FrontBasket
CyfinderWire
2-SplashShields
2 Sidetables
2-BasketEndCaps(leftand Right)
Model920.16203
1-AssemblyInstruction
UseandCareManual
HardwarePackage(seepage2, Hardware)
IgniterPackage
LargeHardwarePackage
FrameKitBox
SideBurnerKit Box
BaseAssembly
ControlPanelAssembly
HeatShield
BottomCasting
TopCasting
Burner
SideBurner
Handle
HeatTent
CookingGrid
BottomWarmingRack
TopWarmingRack
FrontBasket
Side Basket
CylinderWire
Sidetables
2-SplashShields
2-BasketEndCaps(left and Right)
FrameKit
Top
for model
920.16201)
11412242 (Pg, 3)
Assembly instructions
I MPORTANT: Duringassembly,referto PartsDiagramand PartsListson pages14and 15.
Step 1
Open the Frame Kit,
Remove Legs (4 and 13), 2 carriage bolts (DU) and 2 wing nuts (CP).
Locate the Base Assembly (1), Bottom
Casting (42) and Grease Can Wire nmiddleholes
(49) for assembly in this step.
1a-Insert Legs (4 and 13) and
align middle holes, Figure 1.
I b-Lower legs at the same
time onto the Base Assembly
(t). Snap into place, Figure 2.
1 C- Place the Iocator pins on the
Bottom Casting (42) into the
alignment holes on the legs.
Secure with 2 carriage bolts (DU),
2 star washers and 2 wing nuts
(CP), Figure 3.
1d-Placethe Grease Can Wire (49)
into the Bottom Casting, Figure 4.
Note: Grease can not included.
Use an ordinary soup can.
Correct Incorrect
Locatorpins
3
•!•!
|
11412242 (Pg.4)
4
Step 1
DU
DU 42
ld !
i
lc
CP
4
13
11412242 (Pg 5)