Kenmore 91195982990, 91195987990, 91195989990, 91195409000, 91195402000 Installation Guide

INSTALLATION iNSTRUCTIONS FOR YOUR NEW

FREEoSTANDINGELECTRIC NGE

Before you begin. Read these instructions completely end carefully.

nMPORTANT. Save these instructions for local inspector's use.
IMPORTANT - OBSERVE ALL GOVERNB_G CODES AND ORDINANCES.

Note to HnstaHer . Be sure to leave these instructions with the Consumer.

Note =o Consumer. Keep t_ese instructions with your Use and Care Book for future

reference.

house fuse or open circuit breaker |
CAUTION: For personal safety remove

before beginning instaMation. Failure |
to do so could result in serious injury |

°re'e, de h.................. J

All rough-in and spacing dimensions must be met for safe
use ofyour range Electricity to the range can be

disconnected at the outlet without moving the range if the
outlet is in the preferred location (remove lower drawer)

Toreduce the risk of bums or fire when reaching over hot

surface elements, cabinet storage space above the
cooktop should be avoided If cabinet storage space is to

be provided above the cooktop, the risk can be reduced
by installing a range hood that sticks out at least 5" beyond

the front of the cabinets Cabinets installed above a

cooktop may"be no deeper than 73"
Be sure your appliance is properly installed and grounded

by a qualified technician

tipping the appliance, the appliance
WARNING: To reduce the ri_k of

must be secured byproperly iestafied

anti.tip device packed _Jith the
appliance,

Fig. 1

ADJACENTCABINETORFINAL
LOCATIONOF_NGE

WAll

REAR

LEVELINGLEG

Installationinstructionsareprovided for woodand concrete
in eitherfloor or wall Any othertype of constructionmay

requirespecialinstallationtechniquesas deemedneces-
sary toprovide adequatefasteningof theANTI.TIP

brackettothe floorand wall

Theuse ofthis bracketdoes notpreclude tipping of the

range whennot properlyinstalled
NOTE: TheinstallationoftheANTI.TIP bracket must

meetalllocal codesfor securing appliance

• Flat blade screwdriver • I 7/15"open end OF

• 5/t6" hex head screwdriver adjustable wrench

• Drill with 7/8" bit • !/4" Hex Head

• Phillips head screwdriver screwdriver

• Unlessproperlyinstalled,therange ':

could be tipped by steppingor sittingon ::

hot liquidsor fromtherangeitself

• Thisrangehasbeendesigned tomeet

all normalconditions

, fnstatfAnti-tip Devicepacked withrange .. [

.SeeInstallationInstructions

31-10301-1
229C4o53P'! 04,,2 I

Step 1 - Locating #_e bracket

1. Locate the bracket against the rear wall and either the

right or left cabinet. If the countertop overhangs the
cabinet, offset the bracket from the cabinet by the

amount of overhang, tf there is no adjacent cabinet.
position the edge of the bracket at the desired location

of the range side panel

continued...

N D 348_02

2, Usethe bracketas atemplateand markthe4 required

holesasshownin Fig, I for thetype ofconstructionas
indicated in Step 2

Step 2. Anti.Tip bracket installation

Wood Construction

1, Floor: Locatethe centerof thetwoholesidentified in

Fig. 1asFLOOR-WOOD,Drilla 7/8"pifotholein the
centerof eachhole (a nailor awl maybe usedif a drill
isnotavailable),AND

2, Wall: Locatethetwo holesidentified in Fig, 1 as WALL°

Drillan angled t/8" pilot hole (asshowninFig. 2) in the
centerof eachhole (anail or awlmaybeused ifa drill
isnotavailable)

MounttheANTI-TIPbracket withthe4 screwsprovided as
illustratedinFig, 2

Concrete Construction

I. HardwareRequired: 4 each 1/4°x 7-7/2_Iag bolt

(notprovided) 4 each 1/2"0 D sleeveanchor

2. Drilltherecommendedsizehole forthe anchorsintothe
concreteat thecenterof the holesidentified asFLOOR-

CONCRETEand WALL. tnstaflthesleeveanchorinto
thedrilled holesand then installthe lag bolts through

thebracket Thebolts mustbeproperly tightenedas
recommendedforthe hardware

Step 3 - Checking the Installation

Io Completethe installationof therangeper theinstallation

instructionsprovided withtheproduct

2. Checkifthe ANTI-TIPbracketis instafledand engaged

properly Removethekick panel or storage drawerand

inspecttheREAR LEVELINGLEG.Makesure itfits

securelyintothe slot

SeeFigures 3 and4 for allrough-inandspacing
dimensions

Therangemaybe placed withO"clearance(flush)atthe

back wallandside wallsoftherange

Fig. 3

I[

i

T

18 = MIN

0 w .._

i

WtlNIMUM DIMENSIONS BETWEEN COOKTOP,

WALLS, AND ABOVE COOKTOP

" RECOMMENDED SPACING TO HEAT SENSITIVE

SURFACES.

Makesurethewall coverings, countertopand cabinets
aroundtherange can withstandtheheat (up to200_F)

generatedby therange

Fig. 4

ACCEPTABLEELECTRICAL
OUTLETAREA

Orienttheelectrical
receptaclesothe

isparalleltothefloor.

21f2"

NOTE:Usea 4foot powercordtoprevent
interferencewith the storagedrawer.

Longerpowercords mayhaveto be

dressedtoallow for properdrawerclosure,