DRYER OPERATING MNSTRUCTNONS
Model 84082/94082
Hill 0
ll_ied= li£h 0
l_leliu_e 0
Lew 0
lle lear 0
l_l_ellr I 0 Ssfflleat 0
£1urleal 0 $£riskQsa_l 0
Les_IrV © Wdslle£11 0
lae_l 0 llcleSilealO
E_dmated
TU_
0£TI0_,IS Select
Before Operating Your Dryer
Read your dryer Owner's Guide. It has important
safety and warranty information. It also has many sug-
gestions for best drying results.
To reduce the risk of fire, electric
shock or injury to persons, read the IMPORTANT
SAFETY INSTRUCTIONS in your dryer Owner's Guide
before operating this appliance.
6. The changes you make will be remembered the
next time that cycle is selected. See the "Dryer
Settings Chart" for more details.
7. Press START to begin the cycle.
_, To pause the cycle or change settings,
press PAUSE/CANCEL once.To resume
the cycle, press START again.
_, To stop or change the cycle, press
PAUSE/CANCEL twice.
Operating Steps
Read "Drying Procedures" in your Owner's Guide. It
explains these operating steps in detail.
1. Prepare items for drying.
2. Check that lint filter is clean and in place.
3. Load the dryer. If desired, add a dryer fabric
softener sheet. Close the door.
4. Select the cycle and and settings for each load.
5. A suitable drying temperature, dryness level and
options will automatically be displayed for each
cycle. To change the temperature and dryness
level, press TEMP and DRYNESS until the desired
selections are made. To select an option, press
OPTIONS until the indicator for a desired option
flashes and press SELECT. Follow the same
steps to delete an option. If a dryness level or
option is not available for a cycle,it will not light.
8.
A signal will sound at the end of the cycle and
periodically during Wrinkle Rid when the Cycle
Signal option is selected. When the cycle
ends,remove items immediately and hang or
fold.
9. Clean the lint filter after every load.
Cycle Selection
Turn the Cycle Selector knob to the desired cycle.
For best results, follow the fabric care label
instructions on items to be dried. To change the
selection after the cycle has begun, press PAUSE/
CANCEL twice,
Auto Dry
Auto Dry cycles take the guesswork out of drying time.
The load will automatically be dried at the selected
temperature to the desired dryness level. The dryer
senses the moisture level of the load as it tumbles
through heated air. Auto Dry cycles save time and
energy and protect fabrics.When the load has reached
the selected dryness level, it will continue to tumble,
#rVisl 0
O_elll0w_ 0
Wri_kls Ril O
lileas Listlill_e_ 0
0 80
©©
STAIT Pause
Cae_el
unheated, during a Coo! Down period. This helps
reduce wrinkling and makes items easier to handle
during unloading.
Drying time varies depending on size and dampness
of load and fabric type. Room temperature and
humidity, type of installation and electrical voltage or
gas pressure can also affect drying time.
Towels
Select this Auto Dry cycle for towel loads.
Bulky
Select this cycle to dry a comforter, blanket, sleeping
bag or similar item.
Normal
Select this Auto Dry cycle for cotton items.
Perm Press
Select this Auto Dry cycle to dry cottons and blends
with a noqron finish.
Sport
Select this Auto Dry cycle to dry small loads of
lightweight, synthetic apparel worn for working out,
running, swimming, cycling, tennis and similar
activities.
Quick
Select this cycle to quickly dry a small load made up of
just a few items. It provides approximately 20
minutes of tumbling followed by a 1g-minute cool down
period.
PN 134464300 (0412)
Cycle Selection (Don't)
Delicate
Select this Auto Dry cycle for knits and delicate items.
Touch Up
Select Touch Up to help remove wrinkles from clean
and dry items that were not taken from the dryer at the
end of the cycle, have been stored in crowded closets
or drawers, or unpacked from luggage following a trip.
It provides approximately 10 minutes of tumbling
followed by a 5ominute coo! down period.
Timed Dry
To manually select the drying time for any load, turn
the Cycle Selector knob to a numbered setting. Dry-
ing times from 15 to 90 minutes are available in 20-
minute increments. You wil! not be able to select a
cycle or dryness level Timed Dry is recommended
when using the No Heat option.
i
Temperature Selection
For best results, follow the fabric care label
instructions on items to be dried. Press TEMP to
select the drying temperature for each load.
High is recommended for sturdy fabrics.
Medium High is recommended for regular fabrics.
Medium is recommended for wrinkle free, permanent
press and lightweight fabrics.
Low is recommended for delicate fabrics.
No Heat should only be used with a Timed Dry setting
to dry items containing feathers, down, foam rubber,
plastics or rubberolike materials; to freshen clothing,
pillows or blankets; or to dust draperies.
Note: Using No Heat in anyAuto Dry cycle will result in
long drying times and/or wet loads at the end of the
cycle.
To avoid fire hazard, do not use heat
to dry items containing feathers or down, foam rubber,
plastics, or similarly textured, rubberolike materials.
Use the No Heat setting only.
Cycle Adjustments
A suitable dryness level and options will automatically
be displayed for each cycle. The settings can be
changed before the cycle is started. Those adjust-
ments will automatically be remembered each time
that cycle is selected. If a dryness level or option is not
recommened for a cycle, the indicator will not light.
If changes are attempted after the cycle starts, the
status lights will blink and the signal will beep 3 times.
The cycle must be canceled before the settings can
be changed. See the "Dryer Settings Chart" for more
details.
Dryness Leve_
To change the dryness level, press DRYNESS until
the desired selection is made. Select Normal Dry for
most loads.
Occasionally a load may seem too damp or over:dried
at the end of the cycle. To increase drying time for
similar loads in the future, select More Dry. For loads
requiring less drying time, select Less Dry.
Select Damp Dry for items you wish to partially dry
before hanging or ironing.
Note: To prevent over-drying, not every dryness leve!
is available with every cycle.
Options
To select or delete Soft Heat, Shrink Guard, Wrinkle
Rid or Cycle Signal, press OPTIONS until the
blinking light indicates the desired option. Then,
while it is blinking, press SELECT. The indicator
will light when the option has been selected. It will
no longer be lighted when the option has been
deleted. To provide the best care for your laundry
items, not every option is available with every cycle.
Select Soft Heat to protect fabrics from the effects of
over-drying. Wrinkling, static build-up, linting, fading
and harshness can occur if loads are dried too long at
the wrong temperature. As the load tumbles and
becomes drier, the temperature is gradually lowered.
Select Shrink Guard to lower the initial drying
temperature. Add it to the Soft Heat option to further
protect fabrics from overdrying.
Select Wrinkle Rid if the dried load might not be
removed promptly at the end of the cycle. The dry load
will continue tumbling without heat for 30 minutes to
help reduce wrinkling. When the Cycle Signal is
selected, a beep will be heard every 5 minutes as a
reminder to remove the load.
The Cycle Signal will sound at the end of the cycle and
periodically during Wrinkle Rid.
Dryer Features
_ (Contro_ Lock)
To avoid having someone accidentally start or stop
the dryer, press OPTIONS and SELECT at the same
time until the Q (Control Lock) indicator is lighted. To
remove the control lock, press OPTIONS and SELECT
again.
Estimated Time
The estimated total cycle time will be displayed
when the cycle is selected. The approximate time
remaining will be displayed during the cycle.
Drying time varies depending on size and
dampness of load and fabric type. Room tempera-
ture and humidity, type of installation and electrical
voltage or gas pressure can also affect drying time.
Status Lights
The following indicators may be lighted during the
cycle:
Drying
Coo! Down
_, Wrinkle Rid
o Clean Lint Filter
Q (Control Lock)
PN 134464300 (0412)
4 beeps / E4A
ERROR CODE CHART
If the dryer stops, the status lights flash, the signal beeps and a code is displayed, an error has occured. Press PAUSE/CANCEL twice. Consult the Error Code Chart below or the "Avoid
Service Checklist" in the Owner's Guide for the possible cause and solution. Make necessary corrections, then select a cycle and press START. If the dryer stops, status lights flash
again, the beeping continues and the code reappears, please contact service for assistance.
Dryer ran too long Lint filter blocked. Ventilation system clogged. Dryer overloaded.
DRYER SETTINGS CHART
AVAILABLE CYCLE SETTINGS - These temperatures, dryness levels and options are available with the following cycles:
Towel Bulky Normal Perm Press Sport Quick Delicate Touch Up Timed Dry
Estimated drying 15 to 90
time*** 60 minutes 45 minutes 50 minutes 40 minutes 20 minutes 30 minutes 20 minutes 15 minutes minutes
Temperatures
High ,/ ,/ ,/
Medium-High ,/ ,/ ,/ ,/ ,/ ,/
Medium ,/ ,/ ,/ ,/ ,/ ,/ ,/
Low ,/ ,/ ,/ ,/ ,/ ,/ ,/ ,/
"k'k "k'k "k'k "k'k "k'k
No Heat ,/
Dryness Level
More Dry ,/ ,/
"k "k "k "k
Normal Dry ,/ ,/ ,/ ,/ ,/
Less Dry ,/ ,/ ,/ ,/
Damp Dry ,/ ,/ ,/ ,/
Options
Soft Heat ,/ ,/ ,/ ,/ ,/
Shrink Guard ,/ ,/ ,/ ,/
Wrinkle Rid ,/ ,/ ,/ ,/ ,/ ,/ ,/
"k "k "k "k "k "k "k "k "k
Cycle Signal ,/ ,/ ,/ ,/ ,/ ,/ ,/ ,/ ,/
Factory setting ,/ Available settings ** Not recommended *** Estimated cycle duration is based on normal dryness
level and factory settings.
PN 134464300 (0412)
Loading...